/linux/Documentation/devicetree/bindings/sound/ |
H A D | qcom,wcd9335.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause 3 --- 5 $schema: http://devicetree.org/meta-schemas/core.yaml# 10 - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> 13 Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC with in-built 27 clock-names: 29 - const: mclk 30 - const: slimbus 35 interrupt-names: 37 - const: intr1 [all …]
|
H A D | qcom,pm8916-wcd-analog-codec.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause 3 --- 4 $id: http://devicetree.org/schemas/sound/qcom,pm8916-wcd-analog-codec.yaml# 5 $schema: http://devicetree.org/meta-schemas/core.yaml# 10 - Konrad Dybcio <konradybcio@kernel.org> 17 const: qcom,pm8916-wcd-analog-codec 25 interrupt-names: 27 - const: cdc_spk_cnp_int 28 - const: cdc_spk_clip_int 29 - const: cdc_spk_ocp_int [all …]
|
H A D | cirrus,cs42l43.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause 3 --- 5 $schema: http://devicetree.org/meta-schemas/core.yaml# 10 - patches@opensource.cirrus.com 21 - $ref: dai-common.yaml# 26 - cirrus,cs42l43 31 vdd-p-supply: 33 Power supply for the high voltage interface. 35 vdd-a-supply: 37 Power supply for internal analog circuits. [all …]
|
H A D | dialog,da7219.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 3 --- 5 $schema: http://devicetree.org/meta-schemas/core.yaml# 10 - David Rau <David.Rau.opensource@dm.renesas.com> 13 The DA7219 is an ultra low-power audio codec with 14 in-built advanced accessory detection (AAD) for mobile 16 sample rates up to 96 kHz at 24-bit resolution. 28 VDD-supply: 30 VDD power supply for the device. 32 VDDMIC-supply: [all …]
|
H A D | qcom,wcd934x.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 3 --- 5 $schema: http://devicetree.org/meta-schemas/core.yaml# 10 - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> 13 Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC. 14 It has in-built Soundwire controller, pin controller, interrupt mux and 27 reset-gpios: 31 slim-ifc-dev: 38 clock-names: 41 vdd-buck-supply: [all …]
|
/linux/arch/arm64/boot/dts/qcom/ |
H A D | msm8916-pm8916.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only 3 * msm8916-pm8916.dtsi describes common properties (e.g. regulator connections) 6 * were rarely re-used for different purposes. Devices that deviate from the 8 * the necessary properties in the board-specific device tree. 15 vdda-supply = <&pm8916_l2>; 19 vdda-supply = <&pm8916_l2>; 20 vddio-supply = <&pm8916_l6>; 24 vddio-supply = <&pm8916_l6>; 28 pll-supply = <&pm8916_l7>; 32 vdd-cdc-io-supply = <&pm8916_l5>; [all …]
|
H A D | msm8939-pm8916.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only 3 * msm8939-pm8916.dtsi describes common properties (e.g. regulator connections) 6 * were rarely re-used for different purposes. Devices that deviate from the 8 * the necessary properties in the board-specific device tree. 15 vdda-supply = <&pm8916_l2>; 16 vddio-supply = <&pm8916_l6>; 20 vddio-supply = <&pm8916_l6>; 24 vdda-supply = <&pm8916_l2>; 25 vddio-supply = <&pm8916_l6>; 29 vddio-supply = <&pm8916_l6>; [all …]
|
H A D | msm8929-pm8916.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only 3 * msm8929-pm8916.dtsi describes common properties (e.g. regulator connections) 6 * were rarely re-used for different purposes. Devices that deviate from the 8 * the necessary properties in the board-specific device tree. 15 vdda-supply = <&pm8916_l2>; 16 vddio-supply = <&pm8916_l6>; 20 vddio-supply = <&pm8916_l6>; 24 vdda-supply = <&pm8916_l2>; 25 vddio-supply = <&pm8916_l6>; 29 vddio-supply = <&pm8916_l6>; [all …]
|
H A D | msm8916-motorola-harpia.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-motorola-common.dtsi" 10 chassis-type = "handset"; 20 interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>; 22 pinctrl-0 = <&battery_alert_default>; 23 pinctrl-names = "default"; 25 maxim,rsns-microohm = <10000>; 26 maxim,over-heat-temp = <600>; 27 maxim,cold-temp = <(-200)>; [all …]
|
H A D | msm8916-longcheer-l8150.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/interrupt-controller/irq.h> 11 #include <dt-bindings/leds/common.h> 16 chassis-type = "handset"; 25 stdout-path = "serial0"; [all …]
|
H A D | msm8916-asus-z00l.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/interrupt-controller/irq.h> 15 chassis-type = "handset"; 24 stdout-path = "serial0"; 27 gpio-keys { [all …]
|
H A D | msm8916-acer-a1-724.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/interrupt-controller/irq.h> 11 #include <dt-bindings/leds/common.h> 14 * NOTE: The original firmware from Acer can only boot 32-bit kernels. 15 * To boot this device tree using arm64 it is necessary to flash 64-bit [all …]
|
H A D | msm8916-lg-m216.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 13 chassis-type = "handset"; 22 stdout-path = "serial0"; 26 compatible = "simple-battery"; 27 voltage-min-design-microvolt = <3300000>; 28 voltage-max-design-microvolt = <4350000>; [all …]
|
H A D | msm8916-huawei-g7.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 6 /dts-v1/; 8 #include "msm8916-pm8916.dtsi" 9 #include <dt-bindings/gpio/gpio.h> 10 #include <dt-bindings/input/input.h> 11 #include <dt-bindings/interrupt-controller/irq.h> 12 #include <dt-bindings/leds/common.h> 13 #include <dt-bindings/sound/apq8016-lpass.h> 16 * Note: The original firmware from Huawei can only boot 32-bit kernels. 17 * To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP [all …]
|
H A D | msm8916-alcatel-idol347.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/leds/common.h> 15 chassis-type = "handset"; 24 stdout-path = "serial0"; 27 reserved-memory { [all …]
|
H A D | msm8996-xiaomi-common.dtsi | 1 // SPDX-License-Identifier: BSD-3-Clause 8 #include <dt-bindings/input/input.h> 9 #include <dt-bindings/gpio/gpio.h> 10 #include <dt-bindings/leds/common.h> 11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 15 compatible = "gpio-gate-clock"; 17 #clock-cells = <0>; 18 enable-gpios = <&pm8994_gpios 15 GPIO_ACTIVE_HIGH>; 20 pinctrl-names = "default"; 21 pinctrl-0 = <&divclk1_default>; [all …]
|
H A D | msm8916-longcheer-l8910.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 3 /dts-v1/; 5 #include "msm8916-pm8916.dtsi" 6 #include "msm8916-modem-qdsp6.dtsi" 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/leds/common.h> 11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 16 chassis-type = "handset"; 25 stdout-path = "serial0"; [all …]
|
H A D | msm8916-wingtech-wt88047.dts | 1 // SPDX-License-Identifier: GPL-2.0-only 6 /dts-v1/; 8 #include "msm8916-pm8916.dtsi" 9 #include "msm8916-modem-qdsp6.dtsi" 11 #include <dt-bindings/gpio/gpio.h> 12 #include <dt-bindings/input/input.h> 13 #include <dt-bindings/leds/common.h> 18 chassis-type = "handset"; 27 stdout-path = "serial0"; 30 speaker_amp: audio-amplifier { [all …]
|
/linux/arch/arm64/boot/dts/mediatek/ |
H A D | mt8183-kukui-audio-da7219.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0 OR MIT) 10 pinctrl-names = "default"; 11 pinctrl-0 = <&da7219_pins>; 14 interrupts-extended = <&pio 165 IRQ_TYPE_LEVEL_LOW>; 16 dlg,micbias-lvl = <2600>; 17 dlg,mic-amp-in-sel = "diff"; 18 VDD-supply = <&pp1800_alw>; 19 VDDMIC-supply = <&pp3300_alw>; 20 VDDIO-supply = <&pp1800_alw>; 25 dlg,adc-1bit-rpt = <1>; [all …]
|
/linux/arch/arm64/boot/dts/freescale/ |
H A D | imx8mp-verdin-dahlia.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT 7 native-hdmi-connector { 8 compatible = "hdmi-connector"; 14 remote-endpoint = <&hdmi_tx_out>; 20 compatible = "simple-audio-card"; 21 simple-audio-card,bitclock-master = <&codec_dai>; 22 simple-audio-card,format = "i2s"; 23 simple-audio-card,frame-master = <&codec_dai>; 24 simple-audio-card,mclk-fs = <256>; 25 simple-audio-card,name = "verdin-wm8904"; [all …]
|
H A D | imx8mm-verdin-dahlia.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT 7 sound_card: sound-card { 8 compatible = "simple-audio-card"; 9 simple-audio-card,bitclock-master = <&dailink_master>; 10 simple-audio-card,format = "i2s"; 11 simple-audio-card,frame-master = <&dailink_master>; 12 simple-audio-card,mclk-fs = <256>; 13 simple-audio-card,name = "verdin-wm8904"; 14 simple-audio-card,routing = 19 "Headphone Jack", "MICBIAS", [all …]
|
/linux/arch/arm/boot/dts/samsung/ |
H A D | exynos4412-odroidu3.dts | 1 // SPDX-License-Identifier: GPL-2.0 3 * Hardkernel's Exynos4412 based ODROID-U3 board device tree source 7 * Device tree source file for Hardkernel's ODROID-U3 board which is based 11 /dts-v1/; 12 #include <dt-bindings/leds/common.h> 13 #include "exynos4412-odroid-common.dtsi" 14 #include "exynos4412-prime.dtsi" 17 model = "Hardkernel ODROID-U3 board based on Exynos4412"; 18 compatible = "hardkernel,odroid-u3", "samsung,exynos4412", "samsung,exynos4"; 29 vbus_otg_reg: regulator-1 { [all …]
|
H A D | exynos4412-odroidx.dts | 1 // SPDX-License-Identifier: GPL-2.0 3 * Hardkernel's Exynos4412 based ODROID-X board device tree source 7 * Device tree source file for Hardkernel's ODROID-X board which is based 11 /dts-v1/; 12 #include <dt-bindings/leds/common.h> 13 #include "exynos4412-odroid-common.dtsi" 16 model = "Hardkernel ODROID-X board based on Exynos4412"; 17 compatible = "hardkernel,odroid-x", "samsung,exynos4412", "samsung,exynos4"; 29 compatible = "gpio-leds"; 34 default-state = "on"; [all …]
|
/linux/arch/arm/boot/dts/st/ |
H A D | stm32mp157c-phycore-stm32mp15-som.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) 3 * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de> 4 * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved 8 #include <dt-bindings/gpio/gpio.h> 9 #include <dt-bindings/input/input.h> 10 #include <dt-bindings/interrupt-controller/arm-gic.h> 11 #include <dt-bindings/interrupt-controller/irq.h> 12 #include <dt-bindings/leds/common.h> 13 #include <dt-bindings/leds/leds-pca9532.h> 14 #include <dt-bindings/mfd/st,stpmic1.h> [all …]
|
/linux/arch/arm/boot/dts/nvidia/ |
H A D | tegra124-nyan.dtsi | 1 // SPDX-License-Identifier: GPL-2.0 2 #include <dt-bindings/input/input.h> 3 #include <dt-bindings/thermal/thermal.h> 14 stdout-path = "serial0:115200n8"; 20 * missing a unit-address. However, the bootloader on these Chromebook 22 * Adding the unit-address causes the bootloader to create a /memory 34 /delete-node/ memory@80000000; 40 vdd-supply = <&vdd_3v3_hdmi>; 41 pll-supply = <&vdd_hdmi_pll>; 42 hdmi-supply = <&vdd_5v0_hdmi>; [all …]
|