| /linux/Documentation/devicetree/bindings/phy/ |
| H A D | phy-stm32-usbphyc.yaml | 162 st,tune-squelch-level:
164 Tunes the squelch DC threshold value
263 st,tune-squelch-level = <3>;
281 st,tune-squelch-level = <3>;
|
| H A D | nvidia,tegra20-usb-phy.yaml | 193 description: HS squelch detector level.
|
| /linux/Documentation/networking/device_drivers/hamradio/ |
| H A D | baycom.rst | 136 ser12 if software DCD is utilised, the radio's squelch should always be
138 as it is much faster than most hardware squelch circuitry. The
|
| H A D | z8530drv.rst | 620 slow squelch.
|
| /linux/arch/arm/boot/dts/st/ |
| H A D | stm32mp135f-dhcor-dhsbc.dts | 402 st,tune-squelch-level = <1>;
420 st,tune-squelch-level = <1>;
|
| H A D | stm32mp135f-dk.dts | 597 st,tune-squelch-level = <1>;
611 st,tune-squelch-level = <1>;
|
| /linux/drivers/net/ethernet/broadcom/bnxt/ |
| H A D | bnxt_hwrm.h | 19 BNXT_HWRM_CTX_SILENT = BIT(2), /* squelch firmware errors */
|
| /linux/drivers/phy/marvell/ |
| H A D | phy-mvebu-a3700-utmi.c | 145 /* Wait for squelch calibration */ in mvebu_a3700_utmi_phy_power_on()
|
| /linux/drivers/phy/st/ |
| H A D | phy-stm32-usbphyc.c | 526 ret = of_property_read_u32(np, "st,tune-squelch-level", &val); in stm32_usbphyc_phy_tuning()
531 dev_warn(usbphyc->dev, "phy%d: invalid st,tune-squelch\n", index); in stm32_usbphyc_phy_tuning()
|
| /linux/arch/x86/platform/olpc/ |
| H A D | olpc.c | 241 * Squelch SCIs while suspended. This is a fix for in olpc_xo1_ec_suspend()
|
| /linux/drivers/phy/qualcomm/ |
| H A D | phy-qcom-snps-femto-v2.c | 328 "qcom,squelch-detector-bp",
|
| /linux/drivers/phy/rockchip/ |
| H A D | phy-rockchip-naneng-combphy.c | 474 /* Set Rx squelch input filler bandwidth */ in rk3528_combphy_cfg()
999 /* Set Rx squelch input filler bandwidth */ in rk3576_combphy_cfg()
|
| /linux/drivers/hid/ |
| H A D | hid-ntrig.c | 520 case HID_DG_CONTACTID: /* Not trustworthy, squelch for now */ in ntrig_input_mapping()
|
| /linux/drivers/phy/samsung/ |
| H A D | phy-exynos5-usbdrd.c | 2143 /* TX Keeper Disable, Squelch on when U3 */
2198 /* Squelch off when U3 */
|
| /linux/drivers/scsi/mvsas/ |
| H A D | mv_94xx.c | 108 /* R10Ch DFE Resolution Control/Squelch and FFE Setting in set_phy_ffe_tuning()
|
| /linux/drivers/net/hamradio/ |
| H A D | baycom_ser_hdx.c | 298 * PLL algorithm for the hardware squelch DCD algorithm in ser12_rx()
|
| /linux/include/linux/soundwire/ |
| H A D | sdw.h | 660 * @is_mockup_device: status flag used to squelch errors in the command/control
|
| /linux/drivers/net/ethernet/smsc/ |
| H A D | smc91x.h | 753 #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
|
| /linux/drivers/usb/host/ |
| H A D | octeon-hcd.h | 1699 * @sqrxtune: Squelch Threshold Adjustment
|
| /linux/tools/testing/selftests/net/ |
| H A D | pmtu.sh | 1063 # squelch the output of the del-if commands since it can be wordy
|
| /linux/drivers/net/ethernet/marvell/ |
| H A D | skge.h | 1219 PHY_B_AC_L_SQE = 1<<15, /* Bit 15: Low Squelch */
|
| /linux/arch/m68k/ifpsp060/src/ |
| H A D | pfpsp.S | 10273 # 'N' bit for a negative QNAN or SNAN input so we must squelch it here.
|
| H A D | fpsp.S | 13842 # 'N' bit for a negative QNAN or SNAN input so we must squelch it here.
|