| /linux/Documentation/ABI/testing/ |
| H A D | debugfs-driver-dcc | 36 be configured sequentially and not in a overlapping
126 be configured and enabled sequentially, e.g. list
|
| /linux/include/uapi/linux/ |
| H A D | blkzoned.h | 27 * @BLK_ZONE_TYPE_SEQWRITE_REQ: The zone must be written sequentially
28 * @BLK_ZONE_TYPE_SEQWRITE_PREF: The zone can be written non-sequentially
|
| /linux/Documentation/devicetree/bindings/interrupt-controller/ |
| H A D | microchip,sama7g5-eic.yaml | 35 should be specified sequentially from output 0 to output 1.
|
| H A D | actions,owl-sirq.yaml | 38 They shall be specified sequentially from output 0 to 2.
|
| H A D | fsl,irqsteer.yaml | 30 the input interrupts. They should be specified sequentially from
|
| /linux/Documentation/kbuild/ |
| H A D | Kconfig.recursion-issue-01 | 11 # by stepping through the questions it needs to address sequentially.
|
| /linux/arch/mips/include/uapi/asm/ |
| H A D | ucontext.h | 11 * sigcontext. They are placed sequentially in memory at the end of struct
|
| /linux/Documentation/userspace-api/media/rc/ |
| H A D | rc-tables.rst | 381 - Decrease channel sequentially
389 - Increase channel sequentially
|
| /linux/Documentation/devicetree/bindings/firmware/ |
| H A D | cznic,turris-omnia-mcu.yaml | 35 The interrupt numbers correspond sequentially to GPIO numbers, taking the
|
| /linux/Documentation/core-api/ |
| H A D | idr.rst | 45 If you need to allocate IDs sequentially, you can use
|
| /linux/drivers/hid/ |
| H A D | hid-roccat-pyra.h | 102 * These are sent sequentially
|
| /linux/drivers/misc/ibmasm/ |
| H A D | command.c | 100 * Commands are executed sequentially. One command (sp->current_command)
|
| /linux/Documentation/filesystems/ |
| H A D | zonefs.rst | 14 write zones of the device must be written sequentially starting from the end
41 sequentially. Each sequential zone has a write pointer maintained by the
138 Sequential zone files can only be written sequentially, starting from the file
|
| H A D | ubifs.rst | 90 media that read faster sequentially
|
| /linux/drivers/md/ |
| H A D | dm-kcopyd.c | 569 * If we need to write sequentially and some reads or writes failed, in run_io_job()
805 * we need to write sequentially. If one of the destination is a in dm_kcopyd_copy()
818 * If we need to write sequentially, errors cannot be ignored. in dm_kcopyd_copy()
|
| /linux/drivers/net/ieee802154/ |
| H A D | adf7242.c | 182 * Packet RAM sequentially
185 * Packet RAM sequentially
193 #define CMD_SPI_PRAM_WR 0x1E /* Write data sequentially to current
196 #define CMD_SPI_PRAM_RD 0x3E /* Read data sequentially from current
|
| /linux/arch/sh/drivers/dma/ |
| H A D | dmabrg.c | 80 * handles every set and unmasked bit sequentially.
|
| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | field-order.rst | 10 Progressive video transmits all lines of a video image sequentially.
|
| /linux/tools/testing/selftests/kexec/ |
| H A D | test_kexec_file_load.sh | 37 # sequentially. As a result, a policy rule may be defined, but
|
| /linux/net/sctp/ |
| H A D | ulpqueue.c | 413 * Walk through the queue sequentially and look for a sequence of in sctp_ulpq_retrieve_reassembled()
510 * Walk through the queue sequentially and look for the first in sctp_ulpq_retrieve_partial()
609 * Walk through the queue sequentially and look for a sequence of in sctp_ulpq_retrieve_first()
|
| /linux/drivers/net/wireless/marvell/mwifiex/ |
| H A D | init.c | 477 * The following operations are performed sequentially -
593 * The following operations are performed sequentially -
|
| /linux/drivers/pwm/ |
| H A D | pwm-berlin.c | 27 * low three bits of PWM_CONTROL. (Sequentially, they are 1, 4, 8, 16, 64,
|
| /linux/usr/ |
| H A D | gen_initramfs.sh | 32 sequentially and immediately. -u and -g states are preserved across
|
| /linux/Documentation/networking/ |
| H A D | segmentation-offloads.rst | 129 If the value of the IPv4 ID is not sequentially incrementing it will be
|
| /linux/drivers/gpu/drm/i915/gem/ |
| H A D | i915_gem_wait.c | 53 * So instead of looking for boosts sequentially, look for all boosts in i915_gem_object_boost()
|