| /linux/arch/sh/ |
| H A D | Kconfig.cpu | 24 Selecting this option will enable support for SH processors that
34 Selecting this option will enable support for software FPU emulation.
43 Selecting this option will enable support for SH processors that
53 Selecting this option will allow the Linux kernel to use SH3 on-chip
62 Selecting this option will enable an in-kernel API for manipulating
|
| /linux/Documentation/leds/ |
| H A D | ledtrig-usbport.rst | 9 It requires selecting USB ports that should be observed. All available ones are
10 listed as separated entries in a "ports" subdirectory. Selecting is handled by
13 Please note that this trigger allows selecting multiple USB ports for a single
|
| /linux/drivers/iommu/intel/ |
| H A D | Kconfig | 67 Selecting this option will enable a DMAR device at boot time if
84 Selecting this option will enable by default the scalable mode if
97 Selecting this option will enable the performance monitoring
|
| /linux/arch/sh/boards/mach-r2d/ |
| H A D | Kconfig | 9 Selecting this option will configure the kernel for R2D-PLUS.
17 Selecting this option will configure the kernel for R2D-1.
|
| /linux/fs/squashfs/ |
| H A D | Kconfig | 197 file systems will be readable without selecting this option.
212 file systems will be readable without selecting this option.
227 file systems will be readable without selecting this option.
241 file systems will be readable without selecting this option.
|
| /linux/Documentation/devicetree/bindings/sound/ |
| H A D | everest,es8375.yaml | 42 0 represents selecting MCLK.
43 1 represents selecting SCLK.
|
| H A D | adi,adau1701.txt | 19 - adi,pin-config: An array of 12 numerical values selecting one of the
|
| /linux/Documentation/hwmon/ |
| H A D | lm93.rst | 95 #P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this
150 are constrained by the hardware. Selecting a value which is not available
160 frequency values are constrained by the hardware. Selecting a value which is
245 the hardware. Selecting a value which is not available will cause the driver
258 The available ramp times are constrained by the hardware. Selecting a value
|
| /linux/drivers/pinctrl/meson/ |
| H A D | pinctrl-meson-axg-pmx.c | 17 * The value 0 is always selecting the GPIO mode, while other
18 * values (start from 1) for selecting the function mode.
|
| /linux/Documentation/block/ |
| H A D | deadline-iosched.rst | 9 Selecting IO schedulers
12 selecting an io scheduler on a per-device basis.
|
| /linux/drivers/usb/core/ |
| H A D | Kconfig | 143 ACPI selecting value 2 is analogous to selecting value 0.
|
| /linux/arch/sh/boards/mach-sdk7780/ |
| H A D | Kconfig | 12 Selecting this option will enable support for the expansion
|
| /linux/drivers/net/ethernet/pensando/ionic/ |
| H A D | ionic_fw.c | 174 devlink_flash_update_timeout_notify(dl, "Selecting", NULL, in ionic_firmware_update()
186 err = ionic_fw_status_long_wait(ionic, "Selecting", in ionic_firmware_update()
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-led-trigger-usbport | 8 selected for the USB port trigger. Selecting ports makes trigger
|
| /linux/Documentation/admin-guide/hw-vuln/ |
| H A D | index.rst | 6 possible mitigations along with guidance for selecting mitigations if they
|
| /linux/Documentation/networking/ |
| H A D | mptcp.rst | 79 The Packet Scheduler is in charge of selecting which available *subflow(s)* to
94 On Linux, MPTCP can be used by selecting MPTCP instead of TCP when creating the
|
| H A D | secid.rst | 10 the label of the flow. This label of the flow is currently used in selecting
|
| /linux/drivers/scsi/libsas/ |
| H A D | Kconfig | 31 Allows sas hosts to receive SMP frames. Selecting this
|
| /linux/arch/x86/ |
| H A D | Kconfig.cpu | 176 Select this for a VIA C3 "Nehemiah". Selecting this enables usage
184 Select this for a VIA C7. Selecting this uses the correct cache
193 support in order to fully benefit from selecting this option.
|
| /linux/Documentation/maintainer/ |
| H A D | feature-and-driver-maintainers.rst | 97 Selecting the maintainer
101 this section provides guidance on selecting one and describes common
|
| /linux/Documentation/devicetree/bindings/clock/ |
| H A D | gpio-mux-clock.yaml | 25 description: GPIO reference for selecting the parent clock.
|
| /linux/drivers/net/wireless/broadcom/brcm80211/ |
| H A D | Kconfig | 44 Selecting this enables additional code for debug purposes.
|
| /linux/drivers/media/usb/pwc/ |
| H A D | Kconfig | 28 The built-in microphone is enabled by selecting USB Audio support.
|
| /linux/Documentation/userspace-api/media/dvb/ |
| H A D | fe-dishnetwork-send-legacy-cmd.rst | 38 It provides a non-standard method for selecting Diseqc voltage on the
|
| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | common.rst | 13 - Changing device properties, selecting a video and audio input, video
|