Home
last modified time | relevance | path

Searched full:resistors (Results 1 – 25 of 50) sorted by relevance

12

/freebsd/sys/contrib/device-tree/Bindings/leds/
H A Drichtek,rt8515.yaml15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
H A Dleds-lm3532.txt11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
/freebsd/sys/contrib/device-tree/Bindings/usb/
H A Dti,tusb73x0-pci.yaml28 PWRONx# pins are active high and their internal pull-down resistors are
30 and their internal pull-down resistors are enabled.
/freebsd/sys/contrib/device-tree/Bindings/pinctrl/
H A Dpinctrl-mt6797.txt59 or 3 for the advanced pull-up resistors.
61 or 3 for the advanced pull-down resistors.
H A Dmediatek,mt6797-pinctrl.yaml109 Pull up setings for 2 pull resistors, R0 and R1. User can
120 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dmediatek,mt6795-pinctrl.yaml133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dmediatek,pinctrl-mt6795.yaml134 Pull up setings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dmediatek,mt6779-pinctrl.yaml162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dmediatek,mt8183-pinctrl.yaml146 Pull up settings for 2 pull resistors, R0 and R1. User can
158 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dmediatek,mt8365-pinctrl.yaml152 Pull up settings for 2 pull resistors, R0 and R1. User can
166 Pull down settings for 2 pull resistors, R0 and R1. User can
H A Dbrcm,bcm11351-pinctrl.txt88 pull-up resistors (1.2k, 1.8k, 2.7k) available
177 - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
H A Dmediatek,mt7981-pinctrl.yaml389 Pull up settings for 2 pull resistors, R0 and R1. Valid arguments
401 Pull down settings for 2 pull resistors, R0 and R1. Valid arguments
H A Dmediatek,mt7986-pinctrl.yaml335 Pull up settings for 2 pull resistors, R0 and R1. Valid arguments
347 Pull down settings for 2 pull resistors, R0 and R1. Valid arguments
/freebsd/sys/contrib/device-tree/Bindings/mfd/
H A Dadi,adp5585.yaml23 - adi,adp5585-02 # No pull-up resistors by default on special pins
25 - adi,adp5585-04 # Pull-down resistors on all pins by default
31 - adi,adp5589-02 # Pull-down resistors by default on special pins
/freebsd/sys/contrib/device-tree/Bindings/hwmon/
H A Dntc-thermistor.yaml12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
H A Dadi,ltc2991.yaml16 sense resistors or temperature sensing transistors.
/freebsd/sys/contrib/device-tree/Bindings/gpio/
H A Dgpio-xra1403.txt5 - Internal pull-up resistors
H A Dexar,xra1403.yaml17 - Internal pull-up resistors
/freebsd/sys/contrib/device-tree/Bindings/iio/imu/
H A Dst_lsm6dsx.txt24 - st,pullups : enable/disable internal i2c controller pullup resistors.
H A Dst,lsm6dsx.yaml80 description: enable/disable internal i2c controller pullup resistors.
/freebsd/sys/contrib/device-tree/Bindings/net/
H A Dethernet-phy.yaml247 supported by the builtin resistors of the PHY, otherwise the resistors may
/freebsd/sys/contrib/device-tree/Bindings/power/supply/
H A Drichtek,rt9467.yaml18 integrated sensing resistors.
/freebsd/sys/contrib/device-tree/src/arm64/renesas/
H A Dr9a09g056n48-rzv2n-evk.dts288 /* There are no pull-up resistors on the EVK, so enable the internal pull-up */
295 /* There are no pull-up resistors on the EVK, so enable the internal pull-up */
/freebsd/sys/contrib/device-tree/src/arm/st/
H A Dstm32mp153c-lxa-fairytux2-gen2.dts101 * The required pull-up resistors however are on v3v3_hdmi.
/freebsd/share/man/man4/
H A Dlpbb.460 -------- | 1 - .1 uF capacitor | 6 - 10K 5% resistors |

12