xref: /linux/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml (revision a1c613ae4c322ddd58d5a8539dbfba2a0380a8c0) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/pinctrl/renesas,rzn1-pinctrl.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Renesas RZ/N1 Pin Controller
8
9maintainers:
10  - Fabrizio Castro <fabrizio.castro.jz@renesas.com>
11  - Geert Uytterhoeven <geert+renesas@glider.be>
12
13properties:
14  compatible:
15    items:
16      - enum:
17          - renesas,r9a06g032-pinctrl # RZ/N1D
18          - renesas,r9a06g033-pinctrl # RZ/N1S
19      - const: renesas,rzn1-pinctrl   # Generic RZ/N1
20
21  reg:
22    items:
23      - description: GPIO Multiplexing Level1 Register Block
24      - description: GPIO Multiplexing Level2 Register Block
25
26  clocks:
27    maxItems: 1
28
29  clock-names:
30    const: bus
31    description:
32      The bus clock, sometimes described as pclk, for register accesses.
33
34allOf:
35  - $ref: pinctrl.yaml#
36
37required:
38  - compatible
39  - reg
40  - clocks
41  - clock-names
42
43additionalProperties:
44  anyOf:
45    - type: object
46      allOf:
47        - $ref: pincfg-node.yaml#
48        - $ref: pinmux-node.yaml#
49
50      description:
51        A pin multiplexing sub-node describes how to configure a set of (or a
52        single) pin in some desired alternate function mode.
53        A single sub-node may define several pin configurations.
54
55      properties:
56        pinmux:
57          description: |
58            Integer array representing pin number and pin multiplexing
59            configuration.
60            When a pin has to be configured in alternate function mode, use
61            this property to identify the pin by its global index, and provide
62            its alternate function configuration number along with it.
63            When multiple pins are required to be configured as part of the
64            same alternate function they shall be specified as members of the
65            same argument list of a single "pinmux" property.
66            Integers values in the "pinmux" argument list are assembled as:
67            (PIN | MUX_FUNC << 8)
68            where PIN directly corresponds to the pl_gpio pin number and
69            MUX_FUNC is one of the alternate function identifiers defined in:
70            <include/dt-bindings/pinctrl/rzn1-pinctrl.h>
71            These identifiers collapse the IO Multiplex Configuration Level 1
72            and Level 2 numbers that are detailed in the hardware reference
73            manual into a single number. The identifiers for Level 2 are simply
74            offset by 10.  Additional identifiers are provided to specify the
75            MDIO source peripheral.
76
77        bias-disable: true
78        bias-pull-up:
79          description: Pull up the pin with 50 kOhm
80        bias-pull-down:
81          description: Pull down the pin with 50 kOhm
82        bias-high-impedance: true
83        drive-strength:
84          enum: [ 4, 6, 8, 12 ]
85
86      required:
87        - pinmux
88
89      additionalProperties:
90        $ref: "#/additionalProperties/anyOf/0"
91
92    - type: object
93      additionalProperties:
94        $ref: "#/additionalProperties/anyOf/0"
95
96examples:
97  - |
98    #include <dt-bindings/clock/r9a06g032-sysctrl.h>
99    #include <dt-bindings/pinctrl/rzn1-pinctrl.h>
100    pinctrl: pinctrl@40067000 {
101            compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl";
102            reg = <0x40067000 0x1000>, <0x51000000 0x480>;
103            clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>;
104            clock-names = "bus";
105
106            /*
107             * A serial communication interface with a TX output pin and an RX
108             * input pin.
109             */
110            pins_uart0: pins_uart0 {
111                    pinmux = <
112                            RZN1_PINMUX(103, RZN1_FUNC_UART0_I) /* UART0_TXD */
113                            RZN1_PINMUX(104, RZN1_FUNC_UART0_I) /* UART0_RXD */
114                    >;
115            };
116
117            /*
118             * Set the pull-up on the RXD pin of the UART.
119             */
120            pins_uart0_alt: pins_uart0_alt {
121                    pinmux = <RZN1_PINMUX(103, RZN1_FUNC_UART0_I)>;
122
123                    pins_uart6_rx {
124                            pinmux = <RZN1_PINMUX(104, RZN1_FUNC_UART0_I)>;
125                            bias-pull-up;
126                    };
127            };
128    };
129