/linux/drivers/mux/ |
H A D | Kconfig | 13 tristate "Analog Devices ADG792A/ADG792G Multiplexers" 16 ADG792A and ADG792G Wide Bandwidth Triple 4:1 Multiplexers 18 The driver supports both operating the three multiplexers in 25 tristate "Analog Devices ADGS1408/ADGS1409 Multiplexers" 43 multiplexers, which in that case will be operated in parallel.
|
/linux/Documentation/devicetree/bindings/mux/ |
H A D | mux-controller.yaml | 15 several parallel multiplexers. Presumably there will be at least one 17 control several multiplexers for a single consumer. 140 * parallel 4-way multiplexers controlled by the same two GPIO-lines.
|
H A D | adi,adg792a.txt | 1 Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers
|
H A D | gpio-mux.yaml | 14 multiplexers, if the same pins control more than one multiplexer.
|
H A D | reg-mux.yaml | 13 Define register bitfields to be used to control multiplexers. The parent
|
/linux/Documentation/devicetree/bindings/i2c/ |
H A D | i2c-mux-gpmux.yaml | 59 However, I2C transactions to devices behind all I2C multiplexers connected 66 The properties of mux-locked and parent-locked multiplexers are discussed
|
H A D | i2c-mux-ltc4306.txt | 19 multiplexers on the bus and the devices behind them use same I2C addresses.
|
H A D | i2c-mux.yaml | 17 For i2c multiplexers/switches that have child nodes that are a mixture of both
|
H A D | i2c-mux-pca954x.yaml | 63 necessary for example, if there are several multiplexers on the bus and
|
/linux/drivers/iio/multiplexer/ |
H A D | Kconfig | 7 menu "Multiplexers" menu
|
/linux/Documentation/admin-guide/media/ |
H A D | imx.rst | 68 - Two video multiplexers for selecting among multiple sensor inputs 113 multiplexers, but the internal IPUv3 topology downstream from there 151 multiplexers as described below. 154 two video multiplexers. Both CSI0 and CSI1 can receive any virtual 155 channel, as selected by the video multiplexers. 165 These are the video multiplexers. They have two or more sink pads to
|
/linux/Documentation/devicetree/bindings/clock/st/ |
H A D | st,clkgen-mux.txt | 3 This binding supports only simple indexed multiplexers, it does not
|
/linux/include/linux/platform_data/ |
H A D | mlxcpld.h | 11 /* Platform data for the CPLD I2C multiplexers */
|
/linux/sound/soc/codecs/ |
H A D | tlv320aic31xx.h | 49 #define AIC31XX_CLKMUX AIC31XX_REG(0, 4) /* Clock clock Gen muxing, Multiplexers*/ 62 #define AIC31XX_CLKOUTMUX AIC31XX_REG(0, 25) /* Clock setting register 9, Multiplexers */
|
/linux/Documentation/devicetree/bindings/media/ |
H A D | video-mux.yaml | 14 Video multiplexers allow to select between multiple input ports. Video
|
/linux/Documentation/devicetree/bindings/clock/ti/davinci/ |
H A D | pll.txt | 5 an multiplexers for various clock signals.
|
/linux/Documentation/devicetree/bindings/clock/ |
H A D | ingenic,cgu.yaml | 11 typically includes a variety of PLLs, multiplexers, dividers & gates in order
|
/linux/Documentation/devicetree/bindings/iio/adc/ |
H A D | xilinx-xadc.txt | 43 multiplexers for simultaneous sampling.
|
/linux/Documentation/devicetree/bindings/gpio/ |
H A D | gpio-pca95xx.yaml | 13 Bindings for the family of I2C GPIO multiplexers/expanders: NXP PCA95xx,
|
/linux/Documentation/iio/ |
H A D | ad7380.rst | 146 Inputs ``AinX0`` of multiplexers correspond to the first half of IIO channels (i.e
|
/linux/drivers/media/pci/bt8xx/ |
H A D | bttv-cards.c | 2180 …Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled… 2188 …/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/ 4552 * video multiplexers to provide up to 16 video inputs. These 4553 * multiplexers are controlled by the lower 8 GPIO pins of the 4554 * bt878. The multiplexers probably Pericom PI5V331Q or similar. 4589 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/ in picolo_tetra_muxsel()
|
/linux/drivers/spi/ |
H A D | Kconfig | 1285 This adds support for SPI multiplexers. Each SPI mux will be
|
/linux/drivers/media/pci/cx18/ |
H A D | cx18-av-core.c | 675 /* Set up analog front end multiplexers */ in set_input()
|
/linux/drivers/gpio/ |
H A D | Kconfig | 1925 Say yes here to enable a driver for GPIO multiplexers based on latches
|
/linux/drivers/usb/serial/ |
H A D | ftdi_sio_ids.h | 608 * CustomWare / ShipModul NMEA multiplexers product ids (FTDI_VID)
|