| /linux/arch/arm64/boot/dts/marvell/ |
| H A D | armada-3720-espressobin.dtsi | 45 led2: gpio-led2 { label
46 /* led2 is working only on v7 board */
51 led2 {
52 label = "led2";
|
| H A D | armada-3720-espressobin-ultra.dts | 51 led2 {
52 label = "ebin-ultra:green:led2";
|
| H A D | armada-3720-espressobin-v7.dts | 38 &led2 {
|
| H A D | armada-3720-espressobin-v7-emmc.dts | 43 &led2 {
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-health-afe440x | 11 1 LED2
17 Note that channels 5 and 6 represent LED2-ALED2 and LED1-ALED1
|
| /linux/arch/parisc/include/asm/ |
| H A D | led.h | 10 #define LED2 0x04 macro
16 #define LED_DISK_IO LED2 /* for disk activity */
|
| /linux/arch/arm/boot/dts/microchip/ |
| H A D | at91-wb50n.dts | 49 led2 {
50 label = "wb50n:red:led2";
|
| /linux/arch/arm/boot/dts/xilinx/ |
| H A D | zynq-zturn-common.dtsi | 42 usr-led2 {
43 label = "usr-led2";
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | lantiq,pinctrl-xway.txt | 48 clkout1, clkout2, mdio, dfe led0, dfe led1, ephy led0, ephy led1, ephy led2
86 gphy0 led0, gphy0 led1, gphy0 led2, gphy1 led0, gphy1 led1, gphy1 led2
|
| /linux/arch/arc/boot/dts/ |
| H A D | abilis_tb100_dvk.dts | 64 led2 {
65 label = "LED2";
|
| H A D | abilis_tb101_dvk.dts | 64 led2 {
65 label = "LED2";
|
| /linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos4412-odroidx.dts | 37 led2 {
38 label = "led2:mmc0";
|
| H A D | exynos4412-tiny4412.dts | 44 led2 {
45 label = "led2";
|
| /linux/Documentation/devicetree/bindings/leds/ |
| H A D | ti,tps61310.yaml | 16 up to 2 x 400mA (LED1 and LED3) and 800mA (LED2) in flash mode.
17 In torch mode, each sink (LED1, LED2, LED3) supports currents up to 175mA.
|
| /linux/drivers/leds/ |
| H A D | leds-bd2802.c | 40 LED2, enumerator
224 reg = bd2802_get_reg_addr(LED2, RED, BD2802_REG_HOURSETUP); in bd2802_configure()
237 enum led_ids other_led = (id == LED1) ? LED2 : LED1; in bd2802_enable()
551 BD2802_CONTROL_RGBS(led2r, LED2, RED);
552 BD2802_CONTROL_RGBS(led2g, LED2, GREEN);
553 BD2802_CONTROL_RGBS(led2b, LED2, BLUE);
|
| /linux/include/linux/mfd/ |
| H A D | tps65010.h | 115 #define LED2 2 macro
146 * led: LED1 or LED2
189 * and LED2 (with hardware blinking capability, not currently exposed).
|
| H A D | adp5520.h | 135 #define ADP5520_GPIO_C3 (1 << 7) /* LED2 or GPIO7 aka C3 */
156 #define ADP5520_COL_C3 (1 << 7) /* LED2 or GPIO7 aka C3 */
|
| /linux/arch/arm64/boot/dts/freescale/ |
| H A D | mba8mx.dtsi | 77 led2: led2 { label
78 label = "led2";
|
| H A D | imx93-phyboard-segin-peb-eval-01.dtso | 33 user-led2 {
|
| H A D | imx8mm-phyboard-polis-peb-eval-01.dtso | 45 user-led2 {
|
| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | omap5-uevm.dts | 81 led2 {
103 label = "omap5:green:led2";
|
| H A D | logicpd-som-lv-baseboard.dtsi | 34 led2 {
35 label = "led2";
|
| /linux/arch/arm/boot/dts/allwinner/ |
| H A D | sun8i-s3-pinecube.dts | 31 led2 {
32 label = "pine64:ir:led2";
|
| /linux/arch/arm/mach-omap1/ |
| H A D | board-osk.c | 65 /* TPS65010 has four GPIOs. nPG and LED2 can be treated like GPIOs with
237 /* Set LED2 off by default */ in osk_tps_setup()
238 tps65010_set_led(LED2, OFF); in osk_tps_setup()
|
| /linux/arch/arm64/boot/dts/ti/ |
| H A D | k3-am642-hummingboard-t.dts | 39 led2: led-2 { label
40 label = "led2";
|