Home
last modified time | relevance | path

Searched +full:imx21 +full:- +full:uart (Results 1 – 22 of 22) sorted by relevance

/freebsd/sys/contrib/device-tree/src/arm/nxp/imx/
H A Dimx27.dtsi1 // SPDX-License-Identifier: GPL-2.0+
5 #include "imx27-pinfunc.h"
7 #include <dt-bindings/clock/imx27-clock.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/irq.h>
13 #address-cells = <1>;
14 #size-cells = <1>;
17 * pre-existing /chosen node to be available to insert the
43 aitc: aitc-interrupt-controller@10040000 {
[all …]
H A Dimx31.dtsi1 // SPDX-License-Identifier: GPL-2.0+
3 // Copyright 2016-2018 Vladimir Zapolskiy <vz@mleia.com>
4 // Copyright 2012 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
7 #address-cells = <1>;
8 #size-cells = <1>;
11 * pre-existing /chosen node to be available to insert the
34 #address-cells = <1>;
35 #size-cells = <0>;
38 compatible = "arm,arm1136jf-s";
44 avic: interrupt-controller@68000000 {
[all …]
H A Dimx50.dtsi1 // SPDX-License-Identifier: GPL-2.0+
7 #include "imx50-pinfunc.h"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/clock/imx5-clock.h>
12 #address-cells = <1>;
13 #size-cells = <1>;
16 * pre-existin
[all...]
H A Dimx25.dtsi1 // SPDX-License-Identifier: GPL-2.0+
5 #include <dt-bindings/gpio/gpio.h>
6 #include "imx25-pinfunc.h"
9 #address-cells = <1>;
10 #size-cells = <1>;
13 * pre-existing /chosen node to be available to insert the
46 #address-cells = <1>;
47 #size-cell
[all...]
H A Dimx53.dtsi1 // SPDX-License-Identifier: GPL-2.0+
6 #include "imx53-pinfunc.h"
7 #include <dt-bindings/clock/imx5-clock.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controlle
[all...]
H A Dimx6sll.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
4 * Copyright 2017-2018 NXP.
8 #include <dt-bindings/clock/imx6sll-clock.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #include "imx6sll-pinfunc.h"
14 #address-cells = <1>;
15 #size-cells = <1>;
46 #address-cells = <1>;
47 #size-cells = <0>;
[all …]
H A Dimx51.dtsi1 // SPDX-License-Identifier: GPL-2.0+
6 #include "imx51-pinfunc.h"
7 #include <dt-bindings/clock/imx5-clock.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/irq.h>
13 #address-cells = <1>;
14 #size-cells = <1>;
17 * pre-existing /chosen node to be available to insert the
42 tzic: tz-interrupt-controller@e0000000 {
[all …]
H A Dimx35.dtsi1 // SPDX-License-Identifier: GPL-2.0
7 #include "imx35-pinfunc.h"
10 #address-cells = <1>;
11 #size-cells = <1>;
14 * pre-existing /chosen node to be available to insert the
38 #address-cells = <1>;
39 #size-cells = <0>;
42 compatible = "arm,arm1136jf-s";
48 avic: avic-interrupt-controller@68000000 {
49 compatible = "fsl,imx35-avic", "fsl,avic";
[all …]
H A Dimx6sl.dtsi1 // SPDX-License-Identifier: GPL-2.0
5 #include <dt-bindings/interrupt-controller/irq.h>
6 #include "imx6sl-pinfunc.h"
7 #include <dt-bindings/clock/imx6sl-clock.h>
10 #address-cells = <1>;
11 #size-cells = <1>;
14 * pre-existing /chosen node to be available to insert the
50 #address-cells = <1>;
51 #size-cells = <0>;
54 compatible = "arm,cortex-a9";
[all …]
H A Dimx6sx.dtsi1 // SPDX-License-Identifier: GPL-2.0
5 #include <dt-bindings/clock/imx6sx-clock.h>
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/input/input.h>
8 #include <dt-bindings/interrupt-controller/arm-gic.h>
9 #include "imx6sx-pinfunc.h"
12 #address-cells = <1>;
13 #size-cells = <1>;
16 * pre-existing /chosen node to be available to insert the
60 #address-cells = <1>;
[all …]
H A Dimx6qdl.dtsi1 // SPDX-License-Identifier: GPL-2.0+
6 #include <dt-bindings/clock/imx6qdl-clock.h>
7 #include <dt-bindings/input/input.h>
8 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #address-cells = <1>;
12 #size-cells = <1>;
15 * pre-existing /chosen node to be available to insert the
58 compatible = "fixed-clock";
59 #clock-cells = <0>;
60 clock-frequency = <32768>;
[all …]
H A Dimx6ul.dtsi1 // SPDX-License-Identifier: GPL-2.0
5 #include <dt-bindings/clock/imx6ul-clock.h>
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/input/input.h>
8 #include <dt-bindings/interrupt-controller/arm-gic.h>
9 #include "imx6ul-pinfunc.h"
12 #address-cells = <1>;
13 #size-cells = <1>;
16 * pre-existing /chosen node to be available to insert the
57 #address-cells = <1>;
[all …]
H A Dimx7s.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
6 #include <dt-bindings/clock/imx7d-clock.h>
7 #include <dt-bindings/power/imx7-power.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #include <dt-bindings/reset/imx7-reset.h>
12 #include "imx7d-pinfunc.h"
15 #address-cells = <1>;
16 #size-cells = <1>;
[all …]
/freebsd/sys/contrib/device-tree/Bindings/serial/
H A Dfsl-imx-uart.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/serial/fsl-im
[all...]
H A Dfsl-imx-uart.txt1 * Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
4 - compatible : Should be "fsl,<soc>-uart"
5 - reg : Address and length of the register set for the device
6 - interrupts : Should contain uart interrupt
9 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
11 - fsl,inverted-tx , fsl,inverted-rx : Indicate that the hardware attached
15 - rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
16 linux,rs485-enabled-at-boot-time: see rs485.txt. Note that for RS485
17 you must enable either the "uart-has-rtscts" or the "rts-gpios"
18 properties. In case you use "uart-has-rtscts" the signal that controls
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/freescale/
H A Dimx8mn.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 #include <dt-bindings/clock/imx8mn-clock.h>
7 #include <dt-bindings/power/imx8mn-power.h>
8 #include <dt-bindings/reset/imx8mq-reset.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interrupt-controller/arm-gic.h>
12 #include <dt-bindings/thermal/thermal.h>
14 #include "imx8mn-pinfunc.h"
17 interrupt-parent = <&gic>;
[all …]
H A Dimx8mm.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 #include <dt-bindings/clock/imx8mm-clock.h>
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/input/input.h>
9 #include <dt-bindings/interrupt-controller/arm-gic.h>
10 #include <dt-bindings/power/imx8mm-power.h>
11 #include <dt-bindings/reset/imx8mq-reset.h>
12 #include <dt-bindings/thermal/thermal.h>
14 #include "imx8mm-pinfunc.h"
17 interrupt-parent = <&gic>;
[all …]
H A Dimx8mq.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 * Copyright (C) 2017-2018 Pengutronix, Lucas Stach <kernel@pengutronix.de>
7 #include <dt-bindings/clock/imx8mq-clock.h>
8 #include <dt-bindings/power/imx8mq-power.h>
9 #include <dt-bindings/reset/imx8mq-reset.h>
10 #include <dt-bindings/gpio/gpio.h>
11 #include "dt-bindings/input/input.h"
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
13 #include <dt-bindings/thermal/thermal.h>
14 #include <dt-bindings/interconnect/imx8mq.h>
[all …]
H A Dimx8mp.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 #include <dt-bindings/clock/imx8mp-clock.h>
7 #include <dt-bindings/power/imx8mp-power.h>
8 #include <dt-bindings/reset/imx8mp-reset.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interconnect/fsl,imx8mp.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
13 #include <dt-bindings/thermal/thermal.h>
15 #include "imx8mp-pinfunc.h"
[all …]
/freebsd/sys/contrib/device-tree/Bindings/dma/
H A Dfsl-imx-sdma.txt4 - compatible : Should be one of
5 "fsl,imx25-sdma"
6 "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
7 "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
8 "fsl,imx51-sdma"
9 "fsl,imx53-sdma"
10 "fsl,imx6q-sdma"
11 "fsl,imx7d-sdma"
12 "fsl,imx6ul-sdma"
13 "fsl,imx8mq-sdma"
[all …]
/freebsd/sys/dts/arm/
H A Dimx51x.dtsi32 #address-cells = <1>;
33 #size-cells = <1>;
41 #address-cells = <1>;
42 #size-cells = <0>;
48 d-cache-line-size = <32>;
49 i-cache-line-size = <32>;
50 d-cache-size = <0x8000>;
51 i-cache-size = <0x8000>;
53 timebase-frequency = <0>;
54 bus-frequency = <0>;
[all …]
/freebsd/sys/dev/uart/
H A Duart_dev_imx.c1 /*-
2 * SPDX-License-Identifier: BSD-2-Clause
41 #include <dev/uart/uart.h>
42 #include <dev/uart/uart_cpu.h>
43 #include <dev/uart/uart_cpu_fdt.h>
44 #include <dev/uart/uart_bus.h>
45 #include <dev/uart/uart_dev_imx.h>
71 * Low-level UART interface.
98 msg, bas->bsh,
129 * don't know what u-boot might have set up. in imx_uart_getbaud()
[all …]