| /freebsd/sys/contrib/device-tree/Bindings/dma/ |
| H A D | lpc1850-dmamux.txt | 1 NXP LPC18xx/43xx DMA MUX (DMA request router)
4 - compatible: "nxp,lpc1850-dmamux"
5 - reg: Memory map for accessing module
6 - #dma-cells: Should be set to <3>.
7 * 1st cell contain the master dma request signal
8 * 2nd cell contain the mux value (0-3) for the peripheral
11 - dma-requests: Number of DMA requests for the mux
12 - dma-masters: phandle pointing to the DMA controller
14 The DMA controller node need to have the following poroperties:
15 - dma-requests: Number of DMA requests the controller can handle
[all …]
|
| H A D | ti-dma-crossbar.txt | 1 Texas Instruments DMA Crossbar (DMA request router)
4 - compatible: "ti,dra7-dma-crossbar" for DRA7xx DMA crossbar
5 "ti,am335x-edma-crossbar" for AM335x and AM437x
6 - reg: Memory map for accessing module
7 - #dma-cells: Should be set to match with the DMA controller's dma-cells
8 for ti,dra7-dma-crossbar and <3> for ti,am335x-edma-crossbar.
9 - dma-requests: Number of DMA requests the crossbar can receive
10 - dma-masters: phandle pointing to the DMA controller
12 The DMA controller node need to have the following poroperties:
13 - dma-requests: Number of DMA requests the controller can handle
[all …]
|
| H A D | fsl-imx-dma.txt | 1 * Freescale Direct Memory Access (DMA) Controller for i.MX
3 This document will only describe differences to the generic DMA Controller and
4 DMA request bindings as described in dma/dma.txt .
6 * DMA controller
9 - compatible : Should be "fsl,<chip>-dma". chip can be imx1, imx21 or imx27
10 - reg : Should contain DMA registers location and length
11 - interrupts : First item should be DMA interrupt, second one is optional and
12 should contain DMA Error interrupt
13 - #dma-cells : Has to be 1. imx-dma does not support anything else.
16 - dma-channels : Number of DMA channels supported. Should be 16.
[all …]
|
| H A D | mtk-uart-apdma.txt | 4 - compatible should contain:
5 * "mediatek,mt2712-uart-dma" for MT2712 compatible APDMA
6 * "mediatek,mt6577-uart-dma" for MT6577 and all of the above
7 * "mediatek,mt8516-uart-dma", "mediatek,mt6577" for MT8516 SoC
9 - reg: The base address of the APDMA register bank.
11 - interrupts: A single interrupt specifier.
12 One interrupt per dma-requests, or 8 if no dma-requests property is present
14 - dma-requests: The number of DMA channels
16 - clocks : Must contain an entry for each entry in clock-names.
17 See ../clocks/clock-bindings.txt for details.
[all …]
|
| H A D | dma-router.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/dma/dma-router.yaml#
5 $schema: http://devicetree.org/meta-schema
[all...] |
| H A D | owl-dma.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/dma/owl-dma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Actions Semi Owl SoCs DMA controller
10 The OWL DMA is a general-purpose direct memory access controller capable of
11 supporting 10 independent DMA channels for the Actions Semi S700 SoC and 12
12 independent DMA channels for the S500 and S900 SoC variants.
15 - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
18 - $ref: dma-controller.yaml#
[all …]
|
| H A D | arm-pl330.txt | 1 * ARM PrimeCell PL330 DMA Controller
3 The ARM PrimeCell PL330 DMA controller can move blocks of memory contents
7 - compatible: should include both "arm,pl330" and "arm,primecell".
8 - reg: physical base address of the controller and length of memory mapped
10 - interrupts: interrupt number to the cpu.
13 - dma-coherent : Present if dma operations are coherent
14 - #dma-cells: must be <1>. used to represent the number of integer
16 - dma-channels: contains the total number of DMA channels supported by the DMAC
17 - dma-requests: contains the total number of DMA requests supported by the DMAC
18 - arm,pl330-broken-no-flushp: quirk for avoiding to execute DMAFLUSHP
[all …]
|
| H A D | renesas,rzn1-dmamux.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/renesas,rzn1-dmamux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Renesas RZ/N1 DMA mux
10 - Miquel Raynal <miquel.raynal@bootlin.com>
13 - $ref: dma-router.yaml#
17 const: renesas,rzn1-dmamux
21 description: DMA mux first register offset within the system control parent.
23 '#dma-cells':
[all …]
|
| H A D | mediatek,uart-dma.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/mediatek,uart-dma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Long Cheng <long.cheng@mediatek.com>
13 The MediaTek UART APDMA controller provides DMA capabilities
17 - $ref: dma-controller.yaml#
22 - items:
23 - enum:
24 - mediatek,mt2712-uart-dma
[all …]
|
| H A D | owl-dma.txt | 1 * Actions Semi Owl SoCs DMA controller
3 This binding follows the generic DMA bindings defined in dma.txt.
6 - compatible: Should be "actions,s900-dma".
7 - reg: Should contain DMA registers location and length.
8 - interrupts: Should contain 4 interrupts shared by all channel.
9 - #dma-cells: Must be <1>. Used to represent the number of integer
11 - dma-channels: Physical channels supported.
12 - dma-requests: Number of DMA request signals supported by the controller.
13 Refer to Documentation/devicetree/bindings/dma/dma.txt
14 - clocks: Phandle and Specifier of the clock feeding the DMA controller.
[all …]
|
| H A D | fsl,imx-dma.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/dma/fsl,imx-dma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Freescale Direct Memory Access (DMA) Controller for i.MX
10 - Animesh Agarwal <animeshagarwal28@gmail.com>
13 - $ref: dma-controller.yaml#
18 - fsl,imx1-dma
19 - fsl,imx21-dma
20 - fsl,imx27-dma
[all …]
|
| H A D | zxdma.txt | 1 * ZTE ZX296702 DMA controller
4 - compatible: Should be "zte,zx296702-dma"
5 - reg: Should contain DMA registers location and length.
6 - interrupts: Should contain one interrupt shared by all channel
7 - #dma-cells: see dma.txt, should be 1, para number
8 - dma-channels: physical channels supported
9 - dma-requests: virtual channels supported, each virtual channel
11 - clocks: clock required
16 dma: dma-controller@09c00000{
17 compatible = "zte,zx296702-dma";
[all …]
|
| H A D | k3dma.txt | 1 * Hisilicon K3 DMA controller
3 See dma.txt first
6 - compatible: Must be one of
7 - "hisilicon,k3-dma-1.0"
8 - "hisilicon,hisi-pcm-asp-dma-1.0"
9 - reg: Should contain DMA registers location and length.
10 - interrupts: Should contain one interrupt shared by all channel
11 - #dma-cells: see dma.txt, should be 1, para number
12 - dma-channels: physical channels supported
13 - dma-requests: virtual channels supported, each virtual channel
[all …]
|
| H A D | renesas,nbpfaxi.txt | 1 * Renesas "Type-AXI" NBPFAXI* DMA controllers
3 * DMA controller
7 - compatible: must be one of
17 - #dma-cells: must be 2: the first integer is a terminal number, to which this
26 - max-burst-mem-read: limit burst size for memory reads
29 - max-burst-mem-write: limit burst size for memory writes
32 If both max-burst-mem-read and max-burst-mem-write are set, DMA_MEM_TO_MEM
35 You can use dma-channels and dma-requests as described in dma.txt, although they
40 dma: dma-controller@48000000 {
51 #dma-cells = <2>;
[all …]
|
| H A D | mmp-dma.txt | 1 * MARVELL MMP DMA controller
3 Marvell Peripheral DMA Controller
7 - compatible: Should be "marvell,pdma-1.0"
8 - reg: Should contain DMA registers location and length.
9 - interrupts: Either contain all of the per-channel DMA interrupts
13 - dma-channels: Number of DMA channels supported by the controller (defaults
15 - #dma-channels: deprecated
16 - dma-requests: Number of DMA requestor lines supported by the controller
18 - #dma-requests: deprecated
20 "marvell,pdma-1.0"
[all …]
|
| H A D | renesas,shdma.txt | 3 Sh-/r-mobile and R-Car systems often have multiple identical DMA controller
4 instances, capable of serving any of a common set of DMA slave devices, using
6 SHDMA DT nodes to be placed under a DMA multiplexer node. All such compatible
7 DMAC instances have the same number of channels and use the same DMA
8 descriptors. Therefore respective DMA DT bindings can also all be placed in the
12 * DMA multiplexer
15 - compatible: should be "renesas,shdma-mux"
16 - #dma-cells: should be <1>, see "dmas" property below
19 - dma-channels: number of DMA channels
20 - dma-requests: number of DMA request signals
[all …]
|
| H A D | snps-dma.txt | 1 * Synopsys Designware DMA Controller
4 - compatible: "snps,dma-spear1340"
5 - reg: Address range of the DMAC registers
6 - interrupt: Should contain the DMAC interrupt number
7 - dma-channels: Number of channels supported by hardware
8 - dma-requests: Number of DMA request lines supported, up to 16
9 - dma-masters: Number of AHB masters supported by the controller
10 - #dma-cells: must be <3>
11 - chan_allocation_order: order of allocation of channel, 0 (default): ascending,
13 - chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1:
[all …]
|
| H A D | arm-pl08x.txt | 1 * ARM PrimeCells PL080 and PL081 and derivatives DMA controller
4 - compatible: "arm,pl080", "arm,primecell";
7 - arm,primecell-periphid: on the FTDMAC020 the primecell ID is not hard-coded
11 - reg: Address range of the PL08x registers
12 - interrupt: The PL08x interrupt number
13 - clocks: The clock running the IP core clock
14 - clock-names: Must contain "apb_pclk"
15 - lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs
16 - lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs
17 - mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents
[all …]
|
| H A D | st,stm32-dma.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/st,stm32-dma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: STMicroelectronics STM32 DMA Controller
10 The STM32 DMA is a general-purpose direct memory access controller capable of
11 supporting 8 independent DMA channels. Each channel can have up to 8 requests.
12 DMA clients connected to the STM32 DMA controller must use the format
13 described in the dma.txt file, using a four-cell specifier for each
14 channel: a phandle to the DMA controller plus the following four integer cells:
[all …]
|
| H A D | st_fdma.txt | 3 The FDMA is a general-purpose direct memory access controller capable of
4 supporting 16 independent DMA channels. It accepts up to 32 DMA requests.
10 - compatible : Should be one of
11 - st,stih407-fdma-mpe31-11, "st,slim-rproc";
12 - st,stih407-fdma-mpe31-12, "st,slim-rproc";
13 - st,stih407-fdma-mpe31-13, "st,slim-rproc";
14 - reg : Should contain an entry for each name in reg-names
15 - reg-names : Must contain "slimcore", "dmem", "peripherals", "imem" entries
16 - interrupts : Should contain one interrupt shared by all channels
17 - dma-channels : Number of channels supported by the controller
[all …]
|
| H A D | st,stm32-mdma.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/st,stm32-mdma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 The STM32 MDMA is a general-purpose direct memory access controller capable of
11 supporting 64 independent DMA channels with 256 HW requests.
12 DMA clients connected to the STM32 MDMA controller must use the format
13 described in the dma.txt file, using a five-cell specifier for each channel:
21 3. A 32bit mask specifying the DMA channel configuration
22 -bit 0-1: Source increment mode
[all …]
|
| H A D | snps,dma-spear1340.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/dma/snps,dma-spear1340.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Synopsys Designware DMA Controller
10 - Viresh Kumar <vireshk@kernel.org>
11 - Andy Shevchenko <andriy.shevchenko@linux.intel.com>
14 - $ref: dma-controller.yaml#
19 - const: snps,dma-spear1340
20 - items:
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | snps,dwc-qos-ethernet.txt | 13 - compatible: One of:
14 - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
15 Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
16 - "nvidia,tegra186-eqos", "snps,dwc-qo
[all...] |
| /freebsd/sys/contrib/device-tree/Bindings/dma/stm32/ |
| H A D | st,stm32-dma.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/stm32/st,stm32-dma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: STMicroelectronics STM32 DMA Controller
10 The STM32 DMA is a general-purpose direct memory access controller capable of
11 supporting 8 independent DMA channels. Each channel can have up to 8 requests.
12 DMA clients connected to the STM32 DMA controller must use the format
13 described in the dma.txt file, using a four-cell specifier for each
14 channel: a phandle to the DMA controller plus the following four integer cells:
[all …]
|
| H A D | st,stm32-mdma.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/stm32/st,stm32-mdma.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 The STM32 MDMA is a general-purpose direct memory access controller capable of
11 supporting 64 independent DMA channels with 256 HW requests.
12 DMA clients connected to the STM32 MDMA controller must use the format
13 described in the dma.txt file, using a five-cell specifier for each channel:
21 3. A 32bit mask specifying the DMA channel configuration
22 -bit 0-1: Source increment mode
[all …]
|