| /linux/drivers/net/mdio/ |
| H A D | Kconfig | 221 the amlogic g12a SoC. The multiplexers connects either the external
232 the amlogic GXL SoC. The multiplexer connects either the external
242 BCM6368 based Broadcom SoCs. This multiplexer connects one of several
253 iProc based Broadcom SoCs. This multiplexer connects one of several
263 are controlled via GPIO lines. The multiplexer connects one of
275 bus multiplexer connects one of several child MDIO busses to
286 The multiplexer connects one of several child MDIO busses to a
|
| /linux/drivers/sbus/char/ |
| H A D | Kconfig | 37 first I2C controller connects mainly to configuration PROMs (NVRAM,
39 connects to environmental control devices such as fans and
40 temperature sensors. The second controller also connects to the
|
| H A D | bbc_i2c.c | 49 * connects mainly to configuration proms (NVRAM, cpu configuration,
50 * dimm types, etc.). Whereas the second I2C controller connects to
52 * The second controller also connects to the smartcard reader, if present.
|
| /linux/Documentation/devicetree/bindings/iio/adc/ |
| H A D | renesas,rcar-gyroadc.yaml | 75 connects to a shared input pin of the GyroADC.
83 TI/ADI ADC connects to a shared input pin of the GyroADC.
91 ADC connects to a shared input pin of the GyroADC.
|
| /linux/Documentation/devicetree/bindings/display/bridge/ |
| H A D | fsl,imx8qxp-pixel-link.yaml | 34 connects to.
40 link connects to.
|
| /linux/fs/ocfs2/cluster/ |
| H A D | tcp_internal.h | 93 /* connects are attempted from when heartbeat comes up until either hb
97 * shutdown is careful to first mark the nn such that no connects will
|
| /linux/net/ncsi/ |
| H A D | Kconfig | 11 support. Enable this only if your system connects to a network
|
| /linux/drivers/gpu/drm/xe/ |
| H A D | xe_tile_sysfs_types.h | 14 * struct kobj_tile - A tile's kobject struct that connects the kobject
|
| H A D | xe_gt_sysfs_types.h | 14 * struct kobj_gt - A GT's kobject struct that connects the kobject and the GT
|
| /linux/drivers/media/usb/pvrusb2/ |
| H A D | pvrusb2-cs53l32a.h | 13 This module connects the pvrusb2 driver to the I2C chip level
|
| H A D | pvrusb2-video-v4l.h | 13 This module connects the pvrusb2 driver to the I2C chip level
|
| H A D | pvrusb2-cx2584x-v4l.h | 13 This module connects the pvrusb2 driver to the I2C chip level
|
| H A D | pvrusb2-wm8775.h | 13 This module connects the pvrusb2 driver to the I2C chip level
|
| /linux/arch/arm/boot/dts/intel/ixp/ |
| H A D | intel-ixp42x-linksys-wrv54g.dts | 183 * EthB connects to the KS8995 CPU port and faces ports 1-4
228 * EthC connects to MII-P5 on the KS8995 bypassing
|
| /linux/Documentation/devicetree/bindings/sound/ |
| H A D | cs53l30.txt | 26 the hardware design connects both SDOUT1 and SDOUT2
|
| /linux/net/x25/ |
| H A D | Kconfig | 24 One connects to an X.25 network either with a dedicated network card
|
| /linux/Documentation/spi/ |
| H A D | spi-sc18is602.rst | 18 This driver provides connects a NXP SC18IS602/603 I2C-bus to SPI bridge to the
|
| /linux/Documentation/devicetree/bindings/input/ |
| H A D | pine64,pinephone-keyboard.yaml | 14 It connects via I2C, providing a raw scan matrix, a flashing interface, and a
|
| /linux/Documentation/devicetree/bindings/interrupt-controller/ |
| H A D | andestech,plicsw.yaml | 12 controller (PLIC_SW). PLIC_SW directly connects to the machine-mode
|
| /linux/Documentation/devicetree/bindings/display/hisilicon/ |
| H A D | dw-dsi.txt | 12 The input port connects to ADE output port with the reg value "0".
|
| /linux/include/uapi/linux/ |
| H A D | usbdevice_fs.h | 146 * except find out what device connects to what port. */
149 char port [127]; /* e.g. port 3 connects to device 27 */
|
| /linux/tools/include/uapi/linux/ |
| H A D | usbdevice_fs.h | |
| /linux/Documentation/admin-guide/perf/ |
| H A D | starfive_starlink_pmu.rst | 6 StarLink Coherent Network on Chip (CNoC) that connects multiple CPU
|
| /linux/tools/testing/selftests/drivers/net/lib/py/ |
| H A D | __init__.py | 7 Former is for local host only tests, latter creates / connects
|
| /linux/tools/testing/selftests/drivers/net/hw/lib/py/ |
| H A D | __init__.py | 7 Former is for local host only tests, latter creates / connects
|