Searched full:attenuator (Results 1 – 15 of 15) sorted by relevance
| /linux/drivers/iio/amplifiers/ |
| H A D | Kconfig | 21 ADRF5702: 0.125 dB LSB, 8-Bit, Silicon Digital Attenuator 22 ADRF5703: 0.25 dB LSB, 7-Bit, Silicon Digital Attenuator 23 ADRF5720: 0.5 dB LSB, 6-Bit, Silicon Digital Attenuator 24 ADRF5730: 0.5 dB LSB, 6-Bit, Silicon Digital Attenuator 25 ADRF5731: 2 dB LSB, 4-Bit, Silicon Digital Attenuator 26 HMC271A: 1dB LSB 5-Bit Digital Attenuator SMT 27 HMC792A 0.25 dB LSB GaAs MMIC 6-Bit Digital Attenuator 28 HMC1018A: 1.0 dB LSB GaAs MMIC 5-BIT Digital Attenuator 29 HMC1019A: 0.5 dB LSB GaAs MMIC 5-BIT Digital Attenuator 30 HMC1119 0.25 dB LSB, 7-Bit, Silicon Digital Attenuator
|
| H A D | ad8366.c | 8 * ADRF5702: 0.125 dB LSB, 8-Bit, Silicon Digital Attenuator, 50 MHz to 20 GHz 9 * ADRF5703: 0.25 dB LSB, 7-Bit, Silicon Digital Attenuator, 9 kHz to 20 GHz 10 * ADRF5720: 0.5 dB LSB, 6-Bit, Silicon Digital Attenuator, 9 kHz to 40 GHz 11 * ADRF5730: 0.5 dB LSB, 6-Bit, Silicon Digital Attenuator, 100 MHz to 40 GHz 12 * ADRF5731: 2 dB LSB, 4-Bit, Silicon Digital Attenuator, 100 MHz to 40 GHz 13 * HMC271A: 1dB LSB 5-Bit Digital Attenuator SMT, 0.7 - 3.7 GHz 14 * HMC792A 0.25 dB LSB GaAs MMIC 6-Bit Digital Attenuator 15 * HMC1018A: 1.0 dB LSB GaAs MMIC 5-BIT DIGITAL ATTENUATOR, 0.1 - 30 GHz 16 * HMC1019A: 0.5 dB LSB GaAs MMIC 5-BIT DIGITAL ATTENUATOR, 0.1 - 30 GHz 17 * HMC1119 0.25 dB LSB, 7-Bit, Silicon Digital Attenuator
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-frequency-admv1014 | 5 Read/write value for the digital attenuator gain (IF_I) with coarse steps. 11 Read/write value for the digital attenuator gain (IF_Q) with coarse steps. 17 Read/write value for the digital attenuator gain (IF_I) with fine steps. 23 Read/write value for the digital attenuator gain (IF_Q) with fine steps.
|
| /linux/Documentation/devicetree/bindings/iio/amplifiers/ |
| H A D | adi,hmc425a.yaml | 13 Digital Step Attenuator IIO devices with gpio interface. 15 ADRF5750 2 dB LSB, 4-Bit, Silicon Digital Attenuator, 10 MHz to 60 GHz 18 HMC425A 0.5 dB LSB GaAs MMIC 6-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, 2.2 - 8.0 GHz 21 HMC540S 1 dB LSB Silicon MMIC 4-Bit Digital Positive Control Attenuator, 0.1 - 8 GHz
|
| /linux/Documentation/hwmon/ |
| H A D | powr1220.rst | 27 An in-line attenuator allows measurements from 0 to 6 V. The 28 attenuator is enabled or disabled depending on the setting of the 29 input's max value. The driver will enable the attenuator for any
|
| /linux/drivers/input/mouse/ |
| H A D | cyapa_gen6.c | 624 /* 2. IDAC and RX Attenuator Calibration Data (Center Frequency). */ in cyapa_gen6_show_baseline() 633 data[0], /* RX Attenuator Mutual */ in cyapa_gen6_show_baseline() 635 data[2], /* RX Attenuator Self RX */ in cyapa_gen6_show_baseline() 637 data[4], /* RX Attenuator Self TX */ in cyapa_gen6_show_baseline() 641 /* 3. Read Attenuator Trim. */ in cyapa_gen6_show_baseline() 649 /* set attenuator trim values. */ in cyapa_gen6_show_baseline()
|
| /linux/Documentation/devicetree/bindings/clock/ |
| H A D | renesas,versaclock7.yaml | 14 jitter attenuator ICs with fractional and integer dividers.
|
| /linux/sound/soc/codecs/ |
| H A D | ak4458.h | 75 /* DAC Digital attenuator transition time setting
|
| H A D | cs42l56.c | 124 { 32, 0x00 }, /* r20 - ADCA Attenuator */ 125 { 33, 0x00 }, /* r21 - ADCB Attenuator */
|
| /linux/Documentation/admin-guide/media/ |
| H A D | si476x.rst | 98 0x04 fmagc1 FMAGC1 attenuator resistance
|
| H A D | bttv.rst | 765 the main difference is that they have attached a programmable attenuator to 3 782 who make the audio attenuator. Their publicly available data-sheet available
|
| /linux/sound/usb/ |
| H A D | mixer.c | 1770 * min < 0 < max: Attenuator + amplifier? Likely to be sane in check_insane_volume_range() 1772 * min < 0 = max: DSP? Voltage attenuator with FW conversion to dB? in check_insane_volume_range()
|
| /linux/drivers/usb/serial/ |
| H A D | cp210x.c | 135 { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
|
| /linux/drivers/media/dvb-frontends/ |
| H A D | dib7000p.c | 1708 * As the minimum output power of DTA-2111 is -31dBm, a 16 dBm attenuator
|
| /linux/drivers/media/usb/dvb-usb/ |
| H A D | dib0700_devices.c | 1718 … if (rf_gain_limit < 2000) /* activate the external attenuator in case of very high input power */ in dib8096_set_param_override()
|