Home
last modified time | relevance | path

Searched full:stby (Results 1 – 25 of 28) sorted by relevance

12

/linux/Documentation/devicetree/bindings/regulator/
H A Drohm,bd96801-regulator.yaml35 STBY state.
52 STBY state.
56 rohm,keep-on-stby:
58 Keep the regulator powered when PMIC transitions to STBY state.
H A Drohm,bd96802-regulator.yaml33 STBY state.
37 rohm,keep-on-stby:
39 Keep the regulator powered when PMIC transitions to STBY state.
H A Dpfuze100.yaml53 fsl,pmic-stby-poweroff:
/linux/Documentation/devicetree/bindings/display/bridge/
H A Dtoshiba,tc358775.yaml38 stby-gpios:
102 stby-gpios: false
127 stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>;
186 stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>;
/linux/drivers/regulator/
H A Dpcap-regulator.c93 const u8 stby; member
104 .stby = _stby, \
113 /* V5 STBY and LOWPWR are on PCAP_REG_VREG2 */
123 /* VAUX2 ... VSIM2 STBY and LOWPWR are on PCAP_REG_LOWPWR */
133 /* SW3 STBY is on PCAP_REG_AUXVREG */
H A Dbd96801-regulator.c8 * the configurations which should be done when the PMIC is in STBY mode.
14 * should be able to ensure the PMIC is in STBY state when the
20 * Users who require the STBY state configurations can have a look at the
27 * STBY configuration support in your downstream driver ;)
489 * If STBY configs are supported, we must pass node in bd96801_walk_regulator_dt()
502 if (of_property_read_bool(np, "rohm,keep-on-stby")) { in bd96801_walk_regulator_dt()
508 "failed to set %s on-at-stby\n", in bd96801_walk_regulator_dt()
H A Dpfuze100-regulator.c838 "fsl,pmic-stby-poweroff")) in pfuze100_regulator_probe()
/linux/arch/arm64/boot/dts/freescale/
H A Dimx8mp-libra-rdk-fpsc.dts43 reg_can1_stby: regulator-can1-stby {
47 regulator-name = "can1-stby";
51 reg_can2_stby: regulator-can2-stby {
55 regulator-name = "can2-stby";
H A Dimx8mp-phyboard-pollux-rdk.dts67 reg_can1_stby: regulator-can1-stby {
74 regulator-name = "can1-stby";
77 reg_can2_stby: regulator-can2-stby {
84 regulator-name = "can2-stby";
H A Dimx8mp-venice-gw74xx.dts146 reg_can1_stby: regulator-can1-stby {
156 reg_can2_stby: regulator-can2-stby {
/linux/drivers/mfd/
H A Drohm-bd96801.c10 * be done when the PMIC is in STBY mode.
16 * should be able to ensure the PMIC is in STBY state when the
22 * Users who require the STBY state configurations can have a look at the
29 * STBY configuration support or a proper fix in your downstream driver ;)
239 /* Registers which do not update value unless PMIC is in STBY */
244 * change when we write it unless PMIC is in STBY. It's safer to not
257 /* Registers which do not update value unless PMIC is in STBY */
/linux/arch/sh/boards/mach-hp6xx/
H A Dpm_wakeup.S20 ! clear STBY bit
/linux/Documentation/devicetree/bindings/clock/
H A Dimx6q-clock.yaml47 fsl,pmic-stby-poweroff:
/linux/arch/arm/boot/dts/nxp/imx/
H A Dimx6qdl-skov-cpu.dtsi137 reg_can1_stby: regulator-can1-stby {
147 reg_can2_stby: regulator-can2-stby {
H A Dimx6sx-sabreauto.dts60 reg_can_stby: regulator-can-stby {
62 regulator-name = "can-stby";
H A Dimx6sx-sdb.dts149 /* Transceiver EN/STBY is active low on RevB board */
H A Dimx6sx-sdb-reva.dts148 /* Transceiver EN/STBY is active high on RevA board */
H A Dimx7d-zii-rpu2.dts52 reg_can1_stby: regulator-can1-stby {
63 reg_can2_stby: regulator-can2-stby {
/linux/Documentation/devicetree/bindings/mfd/
H A Drohm,bd96802-pmic.yaml81 /* These can be set only when PMIC is in STBY */
H A Drohm,bd96801-pmic.yaml100 /* These can be set only when PMIC is in STBY */
/linux/drivers/iio/magnetometer/
H A Dmag3110.c182 * Takes up to 1/ODR to come out of active mode into stby in mag3110_wait_standby()
245 * to transition to STBY. This can take up to 1 /ODR to occur in mag3110_change_config()
/linux/arch/arm64/boot/dts/allwinner/
H A Dsun50i-a64-amarula-relic.dts44 powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */
/linux/drivers/iio/adc/
H A Dad7606.h129 * @gpio_standby: GPIO descriptor for stand-by signal (STBY),
/linux/Documentation/devicetree/bindings/iio/adc/
H A Dadi,ad7606.yaml100 Must be the device tree identifier of the STBY pin. This pin is used to
/linux/drivers/pmdomain/imx/
H A Dscu-pd.c115 /* Align with the IMX_SC_PM_PW_MODE_[OFF,STBY,LP,ON] macros */

12