| /linux/arch/arm/mach-pxa/ |
| H A D | mfp-pxa27x.h | 136 #define GPIO38_FFUART_RI MFP_CFG_IN(GPIO38, AF1)
181 #define GPIO38_PWM1_OUT MFP_CFG_OUT(GPIO38, AF3, DRIVE_LOW)
236 #define GPIO38_SSP2_TXD MFP_CFG_OUT(GPIO38, AF2, DRIVE_LOW)
259 #define GPIO38_SSP3_TXD MFP_CFG_OUT(GPIO38, AF1, DRIVE_LOW)
315 #define GPIO38_KP_MKIN_4 MFP_CFG_IN(GPIO38, AF2)
354 #define GPIO38_USB_P2_3 MFP_CFG_IN(GPIO38, AF3)
|
| H A D | mfp-pxa320.h | 51 #define GPIO38_AC97_SYNC MFP_CFG(GPIO38, AF1)
254 #define GPIO38_SSP2_RXD MFP_CFG(GPIO38, AF2)
255 #define GPIO38_SSP2_TXD MFP_CFG(GPIO38, AF5)
394 #define GPIO38_U2D_OPMODE1 MFP_CFG(GPIO38, AF4)
|
| H A D | mfp-pxa300.h | 139 #define GPIO38_KP_MKOUT_5 MFP_CFG_LPM(GPIO38, AF5, DRIVE_HIGH)
469 #define GPIO38_UTM_CLK MFP_CFG(GPIO38, AF1)
556 #define GPIO38_ULPI_CLK MFP_CFG(GPIO38, AF1)
|
| /linux/arch/arm64/boot/dts/qcom/ |
| H A D | msm8916-huawei-g7.dts | 277 * However, gpio38 does not change its state when inserting/removing the
283 * It behaves just like gpio38 normally does. Usually GPIO56 is used as
286 * SD card slot and forgot to re-route to gpio38.
|
| H A D | ipq6018-cp01-c1.dts | 59 pins = "gpio38", "gpio39", "gpio40", "gpio41";
|
| H A D | msm8939-sony-xperia-kanuti-tulip.dts | 52 pins = "gpio38";
|
| H A D | apq8096-ifc6640.dts | 109 pins = "gpio38";
119 pins = "gpio38";
|
| H A D | msm8916-lg-c50.dts | 138 pins = "gpio38";
|
| H A D | ipq5332-rdp441.dts | 80 pins = "gpio38";
|
| /linux/drivers/pinctrl/bcm/ |
| H A D | pinctrl-bcm6362.c | 93 PINCTRL_PIN(38, "gpio38"),
198 BCM_PIN_GROUP(gpio38),
357 "gpio38",
|
| H A D | pinctrl-bcm63268.c | 102 PINCTRL_PIN(38, "gpio38"),
221 BCM_PIN_GROUP(gpio38),
357 "gpio38",
|
| H A D | pinctrl-bcm6318.c | 78 PINCTRL_PIN(38, "gpio38"),
182 BCM_PIN_GROUP(gpio38),
|
| /linux/arch/arm/boot/dts/broadcom/ |
| H A D | bcm2835-rpi-cm1-io1.dts | 57 "GPIO38",
|
| H A D | bcm2837-rpi-cm3-io3.dts | 57 "GPIO38",
|
| H A D | bcm2835-rpi-zero.dts | 70 "", /* GPIO38 */
|
| H A D | bcm2835-rpi-b.dts | 68 "", /* GPIO38 */
|
| H A D | bcm2835-rpi-a.dts | 68 "", /* GPIO38 */
|
| H A D | bcm2835-rpi-b-plus.dts | 68 "USB_LIMIT", /* GPIO38 */
|
| H A D | bcm2835-rpi-a-plus.dts | 66 "USB_LIMIT", /* GPIO38 */
|
| H A D | bcm2835-rpi-b-rev2.dts | 68 "", /* GPIO38 */
|
| H A D | bcm2837-rpi-zero-2-w.dts | 80 "NC", /* GPIO38 */
|
| /linux/drivers/pinctrl/ |
| H A D | pinctrl-mlxbf3.c | 87 PINCTRL_PIN(38, "gpio38"),
119 "gpio32", "gpio33", "gpio34", "gpio35", "gpio36", "gpio37", "gpio38", "gpio39",
|
| H A D | pinctrl-lantiq.h | 145 GPIO38, enumerator
|
| /linux/arch/arm/boot/dts/nuvoton/ |
| H A D | nuvoton-npcm750-runbmc-olympus-pincfg.dtsi | 126 gpio38_pins: gpio38-pins {
127 pins = "GPIO38/SMB3CSCL";
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | cirrus,madera.yaml | 56 gpio34, gpio35, gpio36, gpio37, gpio38, gpio39 ]
|