xref: /linux/drivers/net/usb/usbnet.c (revision 822d4a8e390a08ccfaf2abb347ae670b230b196f)
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * USB Network driver infrastructure
4  * Copyright (C) 2000-2005 by David Brownell
5  * Copyright (C) 2003-2005 David Hollis <dhollis@davehollis.com>
6  */
7 
8 /*
9  * This is a generic "USB networking" framework that works with several
10  * kinds of full and high speed networking devices:  host-to-host cables,
11  * smart usb peripherals, and actual Ethernet adapters.
12  *
13  * These devices usually differ in terms of control protocols (if they
14  * even have one!) and sometimes they define new framing to wrap or batch
15  * Ethernet packets.  Otherwise, they talk to USB pretty much the same,
16  * so interface (un)binding, endpoint I/O queues, fault handling, and other
17  * issues can usefully be addressed by this framework.
18  */
19 
20 #include <linux/module.h>
21 #include <linux/hex.h>
22 #include <linux/init.h>
23 #include <linux/netdevice.h>
24 #include <linux/etherdevice.h>
25 #include <linux/ctype.h>
26 #include <linux/ethtool.h>
27 #include <linux/workqueue.h>
28 #include <linux/mii.h>
29 #include <linux/usb.h>
30 #include <linux/usb/usbnet.h>
31 #include <linux/slab.h>
32 #include <linux/kernel.h>
33 #include <linux/pm_runtime.h>
34 
35 /*-------------------------------------------------------------------------*/
36 
37 /*
38  * Nineteen USB 1.1 max size bulk transactions per frame (ms), max.
39  * Several dozen bytes of IPv4 data can fit in two such transactions.
40  * One maximum size Ethernet packet takes twenty four of them.
41  * For high speed, each frame comfortably fits almost 36 max size
42  * Ethernet packets (so queues should be bigger).
43  *
44  * The goal is to let the USB host controller be busy for 5msec or
45  * more before an irq is required, under load.  Jumbograms change
46  * the equation.
47  */
48 #define	MAX_QUEUE_MEMORY	(60 * 1518)
49 #define	RX_QLEN(dev)		((dev)->rx_qlen)
50 #define	TX_QLEN(dev)		((dev)->tx_qlen)
51 
52 // reawaken network queue this soon after stopping; else watchdog barks
53 #define TX_TIMEOUT_JIFFIES	(5*HZ)
54 
55 /* throttle rx/tx briefly after some faults, so hub_wq might disconnect()
56  * us (it polls at HZ/4 usually) before we report too many false errors.
57  */
58 #define THROTTLE_JIFFIES	(HZ/8)
59 
60 // between wakeups
61 #define UNLINK_TIMEOUT_MS	3
62 
63 /*-------------------------------------------------------------------------*/
64 
65 /* use ethtool to change the level for any given device */
66 static int msg_level = -1;
67 module_param (msg_level, int, 0);
68 MODULE_PARM_DESC (msg_level, "Override default message level");
69 
70 /*-------------------------------------------------------------------------*/
71 
72 static const char * const usbnet_event_names[] = {
73 	[EVENT_TX_HALT]		   = "EVENT_TX_HALT",
74 	[EVENT_RX_HALT]		   = "EVENT_RX_HALT",
75 	[EVENT_RX_MEMORY]	   = "EVENT_RX_MEMORY",
76 	[EVENT_STS_SPLIT]	   = "EVENT_STS_SPLIT",
77 	[EVENT_LINK_RESET]	   = "EVENT_LINK_RESET",
78 	[EVENT_RX_PAUSED]	   = "EVENT_RX_PAUSED",
79 	[EVENT_DEV_ASLEEP]	   = "EVENT_DEV_ASLEEP",
80 	[EVENT_DEV_OPEN]	   = "EVENT_DEV_OPEN",
81 	[EVENT_DEVICE_REPORT_IDLE] = "EVENT_DEVICE_REPORT_IDLE",
82 	[EVENT_NO_RUNTIME_PM]	   = "EVENT_NO_RUNTIME_PM",
83 	[EVENT_RX_KILL]		   = "EVENT_RX_KILL",
84 	[EVENT_LINK_CHANGE]	   = "EVENT_LINK_CHANGE",
85 	[EVENT_SET_RX_MODE]	   = "EVENT_SET_RX_MODE",
86 	[EVENT_NO_IP_ALIGN]	   = "EVENT_NO_IP_ALIGN",
87 };
88 
89 /* handles CDC Ethernet and many other network "bulk data" interfaces */
90 int usbnet_get_endpoints(struct usbnet *dev, struct usb_interface *intf)
91 {
92 	int				tmp;
93 	struct usb_host_interface	*alt = NULL;
94 	struct usb_host_endpoint	*in = NULL, *out = NULL;
95 	struct usb_host_endpoint	*status = NULL;
96 
97 	for (tmp = 0; tmp < intf->num_altsetting; tmp++) {
98 		unsigned	ep;
99 
100 		in = out = status = NULL;
101 		alt = intf->altsetting + tmp;
102 
103 		/* take the first altsetting with in-bulk + out-bulk;
104 		 * remember any status endpoint, just in case;
105 		 * ignore other endpoints and altsettings.
106 		 */
107 		for (ep = 0; ep < alt->desc.bNumEndpoints; ep++) {
108 			struct usb_host_endpoint	*e;
109 			int				intr = 0;
110 
111 			e = alt->endpoint + ep;
112 
113 			/* ignore endpoints which cannot transfer data */
114 			if (!usb_endpoint_maxp(&e->desc))
115 				continue;
116 
117 			switch (e->desc.bmAttributes) {
118 			case USB_ENDPOINT_XFER_INT:
119 				if (!usb_endpoint_dir_in(&e->desc))
120 					continue;
121 				intr = 1;
122 				fallthrough;
123 			case USB_ENDPOINT_XFER_BULK:
124 				break;
125 			default:
126 				continue;
127 			}
128 			if (usb_endpoint_dir_in(&e->desc)) {
129 				if (!intr && !in)
130 					in = e;
131 				else if (intr && !status)
132 					status = e;
133 			} else {
134 				if (!out)
135 					out = e;
136 			}
137 		}
138 		if (in && out)
139 			break;
140 	}
141 	if (!alt || !in || !out)
142 		return -EINVAL;
143 
144 	if (alt->desc.bAlternateSetting != 0 ||
145 	    !(dev->driver_info->flags & FLAG_NO_SETINT)) {
146 		tmp = usb_set_interface(dev->udev, alt->desc.bInterfaceNumber,
147 					alt->desc.bAlternateSetting);
148 		if (tmp < 0)
149 			return tmp;
150 	}
151 
152 	dev->in = usb_rcvbulkpipe(dev->udev, usb_endpoint_num(&in->desc));
153 	dev->out = usb_sndbulkpipe(dev->udev, usb_endpoint_num(&out->desc));
154 	dev->status = status;
155 	return 0;
156 }
157 EXPORT_SYMBOL_GPL(usbnet_get_endpoints);
158 
159 int usbnet_get_ethernet_addr(struct usbnet *dev, int iMACAddress)
160 {
161 	u8		addr[ETH_ALEN];
162 	int 		tmp = -1, ret;
163 	unsigned char	buf [13];
164 
165 	ret = usb_string(dev->udev, iMACAddress, buf, sizeof(buf));
166 	if (ret == 12)
167 		tmp = hex2bin(addr, buf, 6);
168 	if (tmp < 0) {
169 		dev_dbg(&dev->udev->dev,
170 			"bad MAC string %d fetch, %d\n", iMACAddress, tmp);
171 		if (ret >= 0)
172 			ret = -EINVAL;
173 		return ret;
174 	}
175 	eth_hw_addr_set(dev->net, addr);
176 	return 0;
177 }
178 EXPORT_SYMBOL_GPL(usbnet_get_ethernet_addr);
179 
180 static bool usbnet_needs_usb_name_format(struct usbnet *dev, struct net_device *net)
181 {
182 	/* Point to point devices which don't have a real MAC address
183 	 * (or report a fake local one) have historically used the usb%d
184 	 * naming. Preserve this..
185 	 */
186 	return (dev->driver_info->flags & FLAG_POINTTOPOINT) != 0 &&
187 		(is_zero_ether_addr(net->dev_addr) ||
188 		 is_local_ether_addr(net->dev_addr));
189 }
190 
191 static void intr_complete(struct urb *urb)
192 {
193 	struct usbnet	*dev = urb->context;
194 	int		status = urb->status;
195 
196 	switch (status) {
197 	/* success */
198 	case 0:
199 		dev->driver_info->status(dev, urb);
200 		break;
201 
202 	/* software-driven interface shutdown */
203 	case -ENOENT:		/* urb killed */
204 	case -ESHUTDOWN:	/* hardware gone */
205 		netif_dbg(dev, ifdown, dev->net,
206 			  "intr shutdown, code %d\n", status);
207 		return;
208 
209 	/* NOTE:  not throttling like RX/TX, since this endpoint
210 	 * already polls infrequently
211 	 */
212 	default:
213 		netdev_dbg(dev->net, "intr status %d\n", status);
214 		break;
215 	}
216 
217 	status = usb_submit_urb(urb, GFP_ATOMIC);
218 	if (status != 0)
219 		netif_err(dev, timer, dev->net,
220 			  "intr resubmit --> %d\n", status);
221 }
222 
223 static int init_status(struct usbnet *dev, struct usb_interface *intf)
224 {
225 	char		*buf = NULL;
226 	unsigned	pipe = 0;
227 	unsigned	maxp;
228 	unsigned	period;
229 
230 	if (!dev->driver_info->status)
231 		return 0;
232 
233 	pipe = usb_rcvintpipe(dev->udev, usb_endpoint_num(&dev->status->desc));
234 	maxp = usb_maxpacket(dev->udev, pipe);
235 
236 	/* avoid 1 msec chatter:  min 8 msec poll rate */
237 	period = max ((int) dev->status->desc.bInterval,
238 		(dev->udev->speed == USB_SPEED_HIGH) ? 7 : 3);
239 
240 	buf = kmalloc(maxp, GFP_KERNEL);
241 	if (buf) {
242 		dev->interrupt = usb_alloc_urb(0, GFP_KERNEL);
243 		if (!dev->interrupt) {
244 			kfree(buf);
245 			return -ENOMEM;
246 		} else {
247 			usb_fill_int_urb(dev->interrupt, dev->udev, pipe,
248 					 buf, maxp, intr_complete, dev, period);
249 			dev->interrupt->transfer_flags |= URB_FREE_BUFFER;
250 			dev_dbg(&intf->dev,
251 				"status ep%din, %d bytes period %d\n",
252 				usb_pipeendpoint(pipe), maxp, period);
253 		}
254 	}
255 	return 0;
256 }
257 
258 /* Submit the interrupt URB if not previously submitted, increasing refcount */
259 int usbnet_status_start(struct usbnet *dev, gfp_t mem_flags)
260 {
261 	int ret = 0;
262 
263 	WARN_ON_ONCE(dev->interrupt == NULL);
264 	if (dev->interrupt) {
265 		mutex_lock(&dev->interrupt_mutex);
266 
267 		if (++dev->interrupt_count == 1)
268 			ret = usb_submit_urb(dev->interrupt, mem_flags);
269 
270 		dev_dbg(&dev->udev->dev, "incremented interrupt URB count to %d\n",
271 			dev->interrupt_count);
272 		mutex_unlock(&dev->interrupt_mutex);
273 	}
274 	return ret;
275 }
276 EXPORT_SYMBOL_GPL(usbnet_status_start);
277 
278 /* For resume; submit interrupt URB if previously submitted */
279 static int __usbnet_status_start_force(struct usbnet *dev, gfp_t mem_flags)
280 {
281 	int ret = 0;
282 
283 	mutex_lock(&dev->interrupt_mutex);
284 	if (dev->interrupt_count) {
285 		ret = usb_submit_urb(dev->interrupt, mem_flags);
286 		dev_dbg(&dev->udev->dev,
287 			"submitted interrupt URB for resume\n");
288 	}
289 	mutex_unlock(&dev->interrupt_mutex);
290 	return ret;
291 }
292 
293 /* Kill the interrupt URB if all submitters want it killed */
294 void usbnet_status_stop(struct usbnet *dev)
295 {
296 	if (dev->interrupt) {
297 		mutex_lock(&dev->interrupt_mutex);
298 		WARN_ON(dev->interrupt_count == 0);
299 
300 		if (dev->interrupt_count && --dev->interrupt_count == 0)
301 			usb_kill_urb(dev->interrupt);
302 
303 		dev_dbg(&dev->udev->dev,
304 			"decremented interrupt URB count to %d\n",
305 			dev->interrupt_count);
306 		mutex_unlock(&dev->interrupt_mutex);
307 	}
308 }
309 EXPORT_SYMBOL_GPL(usbnet_status_stop);
310 
311 /* For suspend; always kill interrupt URB */
312 static void __usbnet_status_stop_force(struct usbnet *dev)
313 {
314 	if (dev->interrupt) {
315 		mutex_lock(&dev->interrupt_mutex);
316 		usb_kill_urb(dev->interrupt);
317 		dev_dbg(&dev->udev->dev, "killed interrupt URB for suspend\n");
318 		mutex_unlock(&dev->interrupt_mutex);
319 	}
320 }
321 
322 /* Passes this packet up the stack, updating its accounting.
323  * Some link protocols batch packets, so their rx_fixup paths
324  * can return clones as well as just modify the original skb.
325  */
326 void usbnet_skb_return(struct usbnet *dev, struct sk_buff *skb)
327 {
328 	struct pcpu_sw_netstats *stats64 = this_cpu_ptr(dev->net->tstats);
329 	unsigned long flags;
330 	int	status;
331 
332 	if (test_bit(EVENT_RX_PAUSED, &dev->flags)) {
333 		skb_queue_tail(&dev->rxq_pause, skb);
334 		return;
335 	}
336 
337 	/* only update if unset to allow minidriver rx_fixup override */
338 	if (skb->protocol == 0)
339 		skb->protocol = eth_type_trans(skb, dev->net);
340 
341 	flags = u64_stats_update_begin_irqsave(&stats64->syncp);
342 	u64_stats_inc(&stats64->rx_packets);
343 	u64_stats_add(&stats64->rx_bytes, skb->len);
344 	u64_stats_update_end_irqrestore(&stats64->syncp, flags);
345 
346 	netif_dbg(dev, rx_status, dev->net, "< rx, len %zu, type 0x%x\n",
347 		  skb->len + sizeof(struct ethhdr), skb->protocol);
348 	memset(skb->cb, 0, sizeof(struct skb_data));
349 
350 	if (skb_defer_rx_timestamp(skb))
351 		return;
352 
353 	status = netif_rx (skb);
354 	if (status != NET_RX_SUCCESS)
355 		netif_dbg(dev, rx_err, dev->net,
356 			  "netif_rx status %d\n", status);
357 }
358 EXPORT_SYMBOL_GPL(usbnet_skb_return);
359 
360 /* must be called if hard_mtu or rx_urb_size changed */
361 void usbnet_update_max_qlen(struct usbnet *dev)
362 {
363 	enum usb_device_speed speed = dev->udev->speed;
364 
365 	if (!dev->rx_urb_size || !dev->hard_mtu)
366 		goto insanity;
367 	switch (speed) {
368 	case USB_SPEED_HIGH:
369 		dev->rx_qlen = MAX_QUEUE_MEMORY / dev->rx_urb_size;
370 		dev->tx_qlen = MAX_QUEUE_MEMORY / dev->hard_mtu;
371 		break;
372 	case USB_SPEED_SUPER:
373 	case USB_SPEED_SUPER_PLUS:
374 		/*
375 		 * Not take default 5ms qlen for super speed HC to
376 		 * save memory, and iperf tests show 2.5ms qlen can
377 		 * work well
378 		 */
379 		dev->rx_qlen = 5 * MAX_QUEUE_MEMORY / dev->rx_urb_size;
380 		dev->tx_qlen = 5 * MAX_QUEUE_MEMORY / dev->hard_mtu;
381 		break;
382 	default:
383 insanity:
384 		dev->rx_qlen = dev->tx_qlen = 4;
385 	}
386 }
387 EXPORT_SYMBOL_GPL(usbnet_update_max_qlen);
388 
389 
390 /*-------------------------------------------------------------------------
391  *
392  * Network Device Driver (peer link to "Host Device", from USB host)
393  *
394  *-------------------------------------------------------------------------*/
395 
396 int usbnet_change_mtu(struct net_device *net, int new_mtu)
397 {
398 	struct usbnet	*dev = netdev_priv(net);
399 	int		ll_mtu = new_mtu + net->hard_header_len;
400 	int		old_hard_mtu = dev->hard_mtu;
401 	int		old_rx_urb_size = dev->rx_urb_size;
402 
403 	// no second zero-length packet read wanted after mtu-sized packets
404 	if ((ll_mtu % dev->maxpacket) == 0)
405 		return -EDOM;
406 	WRITE_ONCE(net->mtu, new_mtu);
407 
408 	dev->hard_mtu = net->mtu + net->hard_header_len;
409 	if (dev->rx_urb_size == old_hard_mtu) {
410 		dev->rx_urb_size = dev->hard_mtu;
411 		if (dev->rx_urb_size > old_rx_urb_size) {
412 			usbnet_pause_rx(dev);
413 			usbnet_unlink_rx_urbs(dev);
414 			usbnet_resume_rx(dev);
415 		}
416 	}
417 
418 	/* max qlen depend on hard_mtu and rx_urb_size */
419 	usbnet_update_max_qlen(dev);
420 
421 	return 0;
422 }
423 EXPORT_SYMBOL_GPL(usbnet_change_mtu);
424 
425 /* The caller must hold list->lock */
426 static void __usbnet_queue_skb(struct sk_buff_head *list,
427 			struct sk_buff *newsk, enum skb_state state)
428 {
429 	struct skb_data *entry = (struct skb_data *) newsk->cb;
430 
431 	__skb_queue_tail(list, newsk);
432 	entry->state = state;
433 }
434 
435 /*-------------------------------------------------------------------------*/
436 
437 /* some LK 2.4 HCDs oopsed if we freed or resubmitted urbs from
438  * completion callbacks.  2.5 should have fixed those bugs...
439  */
440 
441 static enum skb_state defer_bh(struct usbnet *dev, struct sk_buff *skb,
442 		struct sk_buff_head *list, enum skb_state state)
443 {
444 	unsigned long		flags;
445 	enum skb_state 		old_state;
446 	struct skb_data *entry = (struct skb_data *) skb->cb;
447 
448 	spin_lock_irqsave(&list->lock, flags);
449 	old_state = entry->state;
450 	entry->state = state;
451 	__skb_unlink(skb, list);
452 
453 	/* defer_bh() is never called with list == &dev->done.
454 	 * spin_lock_nested() tells lockdep that it is OK to take
455 	 * dev->done.lock here with list->lock held.
456 	 */
457 	spin_lock_nested(&dev->done.lock, SINGLE_DEPTH_NESTING);
458 
459 	__skb_queue_tail(&dev->done, skb);
460 	if (dev->done.qlen == 1)
461 		queue_work(system_bh_wq, &dev->bh_work);
462 	spin_unlock(&dev->done.lock);
463 	spin_unlock_irqrestore(&list->lock, flags);
464 	return old_state;
465 }
466 
467 /* some work can't be done in tasklets, so we use keventd
468  *
469  * NOTE:  annoying asymmetry:  if it's active, schedule_work() fails,
470  * but tasklet_schedule() doesn't.  hope the failure is rare.
471  */
472 void usbnet_defer_kevent(struct usbnet *dev, int work)
473 {
474 	set_bit (work, &dev->flags);
475 	if (!usbnet_going_away(dev)) {
476 		if (!schedule_work(&dev->kevent))
477 			netdev_dbg(dev->net,
478 				   "kevent %s may have been dropped\n",
479 				   usbnet_event_names[work]);
480 		else
481 			netdev_dbg(dev->net,
482 				   "kevent %s scheduled\n", usbnet_event_names[work]);
483 	}
484 }
485 EXPORT_SYMBOL_GPL(usbnet_defer_kevent);
486 
487 /*-------------------------------------------------------------------------*/
488 
489 static void rx_complete(struct urb *urb);
490 
491 static int rx_submit(struct usbnet *dev, struct urb *urb, gfp_t flags)
492 {
493 	struct sk_buff		*skb;
494 	struct skb_data		*entry;
495 	int			retval = 0;
496 	unsigned long		lockflags;
497 	size_t			size = dev->rx_urb_size;
498 
499 	/* prevent rx skb allocation when error ratio is high */
500 	if (test_bit(EVENT_RX_KILL, &dev->flags)) {
501 		usb_free_urb(urb);
502 		return -ENOLINK;
503 	}
504 
505 	if (test_bit(EVENT_NO_IP_ALIGN, &dev->flags))
506 		skb = __netdev_alloc_skb(dev->net, size, flags);
507 	else
508 		skb = __netdev_alloc_skb_ip_align(dev->net, size, flags);
509 	if (!skb) {
510 		netif_dbg(dev, rx_err, dev->net, "no rx skb\n");
511 		usbnet_defer_kevent(dev, EVENT_RX_MEMORY);
512 		usb_free_urb(urb);
513 		return -ENOMEM;
514 	}
515 
516 	entry = (struct skb_data *) skb->cb;
517 	entry->urb = urb;
518 	entry->dev = dev;
519 	entry->length = 0;
520 
521 	usb_fill_bulk_urb(urb, dev->udev, dev->in,
522 			  skb->data, size, rx_complete, skb);
523 
524 	spin_lock_irqsave(&dev->rxq.lock, lockflags);
525 
526 	if (netif_running(dev->net) &&
527 	    netif_device_present(dev->net) &&
528 	    test_bit(EVENT_DEV_OPEN, &dev->flags) &&
529 	    !test_bit(EVENT_RX_HALT, &dev->flags) &&
530 	    !test_bit(EVENT_DEV_ASLEEP, &dev->flags) &&
531 	    !usbnet_going_away(dev)) {
532 		switch (retval = usb_submit_urb(urb, GFP_ATOMIC)) {
533 		case -EPIPE:
534 			usbnet_defer_kevent(dev, EVENT_RX_HALT);
535 			break;
536 		case -ENOMEM:
537 			usbnet_defer_kevent(dev, EVENT_RX_MEMORY);
538 			break;
539 		case -ENODEV:
540 			netif_dbg(dev, ifdown, dev->net, "device gone\n");
541 			netif_device_detach(dev->net);
542 			break;
543 		case -EHOSTUNREACH:
544 			retval = -ENOLINK;
545 			break;
546 		default:
547 			netif_dbg(dev, rx_err, dev->net,
548 				  "rx submit, %d\n", retval);
549 			queue_work(system_bh_wq, &dev->bh_work);
550 			break;
551 		case 0:
552 			__usbnet_queue_skb(&dev->rxq, skb, rx_start);
553 		}
554 	} else {
555 		netif_dbg(dev, ifdown, dev->net, "rx: stopped\n");
556 		retval = -ENOLINK;
557 	}
558 	spin_unlock_irqrestore(&dev->rxq.lock, lockflags);
559 	if (retval) {
560 		dev_kfree_skb_any(skb);
561 		usb_free_urb(urb);
562 	}
563 	return retval;
564 }
565 
566 
567 /*-------------------------------------------------------------------------*/
568 
569 static inline int rx_process(struct usbnet *dev, struct sk_buff *skb)
570 {
571 	if (dev->driver_info->rx_fixup &&
572 	    !dev->driver_info->rx_fixup(dev, skb)) {
573 		/* With RX_ASSEMBLE, rx_fixup() must update counters */
574 		if (!(dev->driver_info->flags & FLAG_RX_ASSEMBLE))
575 			dev->net->stats.rx_errors++;
576 		return -EPROTO;
577 	}
578 	// else network stack removes extra byte if we forced a short packet
579 
580 	/* all data was already cloned from skb inside the driver */
581 	if (dev->driver_info->flags & FLAG_MULTI_PACKET)
582 		return -EALREADY;
583 
584 	if (skb->len < ETH_HLEN) {
585 		dev->net->stats.rx_errors++;
586 		dev->net->stats.rx_length_errors++;
587 		netif_dbg(dev, rx_err, dev->net, "rx length %d\n", skb->len);
588 		return -EPROTO;
589 	}
590 
591 	usbnet_skb_return(dev, skb);
592 	return 0;
593 }
594 
595 /*-------------------------------------------------------------------------*/
596 
597 static void rx_complete(struct urb *urb)
598 {
599 	struct sk_buff		*skb = (struct sk_buff *) urb->context;
600 	struct skb_data		*entry = (struct skb_data *) skb->cb;
601 	struct usbnet		*dev = entry->dev;
602 	int			urb_status = urb->status;
603 	enum skb_state		state;
604 
605 	skb_put(skb, urb->actual_length);
606 	state = rx_done;
607 	entry->urb = NULL;
608 
609 	switch (urb_status) {
610 	/* success */
611 	case 0:
612 		break;
613 
614 	/* stalls need manual reset. this is rare ... except that
615 	 * when going through USB 2.0 TTs, unplug appears this way.
616 	 * we avoid the highspeed version of the ETIMEDOUT/EILSEQ
617 	 * storm, recovering as needed.
618 	 */
619 	case -EPIPE:
620 		dev->net->stats.rx_errors++;
621 		usbnet_defer_kevent(dev, EVENT_RX_HALT);
622 		fallthrough;
623 
624 	/* software-driven interface shutdown */
625 	case -ECONNRESET:		/* async unlink */
626 	case -ESHUTDOWN:		/* hardware gone */
627 		netif_dbg(dev, ifdown, dev->net,
628 			  "rx shutdown, code %d\n", urb_status);
629 		goto block;
630 
631 	/* we get controller i/o faults during hub_wq disconnect() delays.
632 	 * throttle down resubmits, to avoid log floods; just temporarily,
633 	 * so we still recover when the fault isn't a hub_wq delay.
634 	 */
635 	case -EPROTO:
636 	case -ETIME:
637 	case -EILSEQ:
638 		dev->net->stats.rx_errors++;
639 		if (!timer_pending(&dev->delay)) {
640 			mod_timer(&dev->delay, jiffies + THROTTLE_JIFFIES);
641 			netif_dbg(dev, link, dev->net,
642 				  "rx throttle %d\n", urb_status);
643 		}
644 block:
645 		state = rx_cleanup;
646 		entry->urb = urb;
647 		urb = NULL;
648 		break;
649 
650 	/* data overrun ... flush fifo? */
651 	case -EOVERFLOW:
652 		dev->net->stats.rx_over_errors++;
653 		fallthrough;
654 
655 	default:
656 		state = rx_cleanup;
657 		dev->net->stats.rx_errors++;
658 		netif_dbg(dev, rx_err, dev->net, "rx status %d\n", urb_status);
659 		break;
660 	}
661 
662 	/* stop rx if packet error rate is high */
663 	if (++dev->pkt_cnt > 30) {
664 		dev->pkt_cnt = 0;
665 		dev->pkt_err = 0;
666 	} else {
667 		if (state == rx_cleanup)
668 			dev->pkt_err++;
669 		if (dev->pkt_err > 20)
670 			set_bit(EVENT_RX_KILL, &dev->flags);
671 	}
672 
673 	state = defer_bh(dev, skb, &dev->rxq, state);
674 
675 	if (urb) {
676 		if (netif_running(dev->net) &&
677 		    !test_bit(EVENT_RX_HALT, &dev->flags) &&
678 		    state != unlink_start) {
679 			rx_submit(dev, urb, GFP_ATOMIC);
680 			usb_mark_last_busy(dev->udev);
681 			return;
682 		}
683 		usb_free_urb(urb);
684 	}
685 	netif_dbg(dev, rx_err, dev->net, "no read resubmitted\n");
686 }
687 
688 /*-------------------------------------------------------------------------*/
689 void usbnet_pause_rx(struct usbnet *dev)
690 {
691 	set_bit(EVENT_RX_PAUSED, &dev->flags);
692 
693 	netif_dbg(dev, rx_status, dev->net, "paused rx queue enabled\n");
694 }
695 EXPORT_SYMBOL_GPL(usbnet_pause_rx);
696 
697 void usbnet_resume_rx(struct usbnet *dev)
698 {
699 	struct sk_buff *skb;
700 	int num = 0;
701 
702 	local_bh_disable();
703 	clear_bit(EVENT_RX_PAUSED, &dev->flags);
704 
705 	while ((skb = skb_dequeue(&dev->rxq_pause)) != NULL) {
706 		usbnet_skb_return(dev, skb);
707 		num++;
708 	}
709 
710 	queue_work(system_bh_wq, &dev->bh_work);
711 	local_bh_enable();
712 
713 	netif_dbg(dev, rx_status, dev->net,
714 		  "paused rx queue disabled, %d skbs requeued\n", num);
715 }
716 EXPORT_SYMBOL_GPL(usbnet_resume_rx);
717 
718 void usbnet_purge_paused_rxq(struct usbnet *dev)
719 {
720 	skb_queue_purge(&dev->rxq_pause);
721 }
722 EXPORT_SYMBOL_GPL(usbnet_purge_paused_rxq);
723 
724 /*-------------------------------------------------------------------------*/
725 
726 // unlink pending rx/tx; completion handlers do all other cleanup
727 
728 static int unlink_urbs(struct usbnet *dev, struct sk_buff_head *q)
729 {
730 	unsigned long		flags;
731 	struct sk_buff		*skb;
732 	int			count = 0;
733 
734 	spin_lock_irqsave (&q->lock, flags);
735 	while (!skb_queue_empty(q)) {
736 		struct skb_data		*entry;
737 		struct urb		*urb;
738 		int			retval;
739 
740 		skb_queue_walk(q, skb) {
741 			entry = (struct skb_data *) skb->cb;
742 			if (entry->state != unlink_start)
743 				goto found;
744 		}
745 		break;
746 found:
747 		entry->state = unlink_start;
748 		urb = entry->urb;
749 
750 		/*
751 		 * Get reference count of the URB to avoid it to be
752 		 * freed during usb_unlink_urb, which may trigger
753 		 * use-after-free problem inside usb_unlink_urb since
754 		 * usb_unlink_urb is always racing with .complete
755 		 * handler(include defer_bh).
756 		 */
757 		usb_get_urb(urb);
758 		spin_unlock_irqrestore(&q->lock, flags);
759 		// during some PM-driven resume scenarios,
760 		// these (async) unlinks complete immediately
761 		retval = usb_unlink_urb(urb);
762 		if (retval != -EINPROGRESS && retval != 0)
763 			netdev_dbg(dev->net, "unlink urb err, %d\n", retval);
764 		else
765 			count++;
766 		usb_put_urb(urb);
767 		spin_lock_irqsave(&q->lock, flags);
768 	}
769 	spin_unlock_irqrestore(&q->lock, flags);
770 	return count;
771 }
772 
773 // Flush all pending rx urbs
774 // minidrivers may need to do this when the MTU changes
775 
776 void usbnet_unlink_rx_urbs(struct usbnet *dev)
777 {
778 	if (netif_running(dev->net)) {
779 		(void) unlink_urbs (dev, &dev->rxq);
780 		queue_work(system_bh_wq, &dev->bh_work);
781 	}
782 }
783 EXPORT_SYMBOL_GPL(usbnet_unlink_rx_urbs);
784 
785 /*-------------------------------------------------------------------------*/
786 
787 static void wait_skb_queue_empty(struct sk_buff_head *q)
788 {
789 	unsigned long flags;
790 
791 	spin_lock_irqsave(&q->lock, flags);
792 	while (!skb_queue_empty(q)) {
793 		spin_unlock_irqrestore(&q->lock, flags);
794 		schedule_timeout(msecs_to_jiffies(UNLINK_TIMEOUT_MS));
795 		set_current_state(TASK_UNINTERRUPTIBLE);
796 		spin_lock_irqsave(&q->lock, flags);
797 	}
798 	spin_unlock_irqrestore(&q->lock, flags);
799 }
800 
801 // precondition: never called in_interrupt
802 static void usbnet_terminate_urbs(struct usbnet *dev)
803 {
804 	DECLARE_WAITQUEUE(wait, current);
805 	int temp;
806 
807 	/* ensure there are no more active urbs */
808 	add_wait_queue(&dev->wait, &wait);
809 	set_current_state(TASK_UNINTERRUPTIBLE);
810 	temp = unlink_urbs(dev, &dev->txq) +
811 		unlink_urbs(dev, &dev->rxq);
812 
813 	/* maybe wait for deletions to finish. */
814 	wait_skb_queue_empty(&dev->rxq);
815 	wait_skb_queue_empty(&dev->txq);
816 	wait_skb_queue_empty(&dev->done);
817 	netif_dbg(dev, ifdown, dev->net,
818 		  "waited for %d urb completions\n", temp);
819 	set_current_state(TASK_RUNNING);
820 	remove_wait_queue(&dev->wait, &wait);
821 }
822 
823 int usbnet_stop(struct net_device *net)
824 {
825 	struct usbnet		*dev = netdev_priv(net);
826 	const struct driver_info *info = dev->driver_info;
827 	int			retval, pm, mpn;
828 
829 	clear_bit(EVENT_DEV_OPEN, &dev->flags);
830 	netif_stop_queue(net);
831 
832 	netif_info(dev, ifdown, dev->net,
833 		   "stop stats: rx/tx %lu/%lu, errs %lu/%lu\n",
834 		   net->stats.rx_packets, net->stats.tx_packets,
835 		   net->stats.rx_errors, net->stats.tx_errors);
836 
837 	/* to not race resume */
838 	pm = usb_autopm_get_interface(dev->intf);
839 	/* allow minidriver to stop correctly (wireless devices to turn off
840 	 * radio etc) */
841 	if (info->stop) {
842 		retval = info->stop(dev);
843 		if (retval < 0)
844 			netif_info(dev, ifdown, dev->net,
845 				   "stop fail (%d) usbnet usb-%s-%s, %s\n",
846 				   retval,
847 				   dev->udev->bus->bus_name, dev->udev->devpath,
848 				   info->description);
849 	}
850 
851 	if (!(info->flags & FLAG_AVOID_UNLINK_URBS))
852 		usbnet_terminate_urbs(dev);
853 
854 	usbnet_status_stop(dev);
855 
856 	usbnet_purge_paused_rxq(dev);
857 
858 	mpn = !test_and_clear_bit(EVENT_NO_RUNTIME_PM, &dev->flags);
859 
860 	/* deferred work (timer, softirq, task) must also stop */
861 	dev->flags = 0;
862 	timer_delete_sync(&dev->delay);
863 	cancel_work_sync(&dev->bh_work);
864 	cancel_work_sync(&dev->kevent);
865 
866 	/* We have cyclic dependencies. Those calls are needed
867 	 * to break a cycle. We cannot fall into the gaps because
868 	 * we have a flag
869 	 */
870 	cancel_work_sync(&dev->bh_work);
871 	timer_delete_sync(&dev->delay);
872 	cancel_work_sync(&dev->kevent);
873 
874 	netdev_reset_queue(net);
875 
876 	if (!pm)
877 		usb_autopm_put_interface(dev->intf);
878 
879 	if (info->manage_power && mpn)
880 		info->manage_power(dev, 0);
881 	else
882 		usb_autopm_put_interface(dev->intf);
883 
884 	return 0;
885 }
886 EXPORT_SYMBOL_GPL(usbnet_stop);
887 
888 /*-------------------------------------------------------------------------*/
889 
890 // posts reads, and enables write queuing
891 
892 // precondition: never called in_interrupt
893 
894 int usbnet_open(struct net_device *net)
895 {
896 	struct usbnet		*dev = netdev_priv(net);
897 	int			retval;
898 	const struct driver_info *info = dev->driver_info;
899 
900 	if ((retval = usb_autopm_get_interface(dev->intf)) < 0) {
901 		netif_info(dev, ifup, dev->net,
902 			   "resumption fail (%d) usbnet usb-%s-%s, %s\n",
903 			   retval,
904 			   dev->udev->bus->bus_name,
905 			   dev->udev->devpath,
906 			   info->description);
907 		goto done_nopm;
908 	}
909 
910 	// put into "known safe" state
911 	if (info->reset) {
912 		retval = info->reset(dev);
913 		if (retval < 0) {
914 			netif_info(dev, ifup, dev->net,
915 				   "open reset fail (%d) usbnet usb-%s-%s, %s\n",
916 				   retval,
917 				   dev->udev->bus->bus_name,
918 				   dev->udev->devpath,
919 				   info->description);
920 			goto done;
921 		}
922 	}
923 
924 	/* hard_mtu or rx_urb_size may change in reset() */
925 	usbnet_update_max_qlen(dev);
926 
927 	// insist peer be connected
928 	if (info->check_connect) {
929 		retval = info->check_connect(dev);
930 		if (retval < 0) {
931 			netif_err(dev, ifup, dev->net, "can't open; %d\n", retval);
932 			goto done;
933 		}
934 	}
935 
936 	/* start any status interrupt transfer */
937 	if (dev->interrupt) {
938 		retval = usbnet_status_start(dev, GFP_KERNEL);
939 		if (retval < 0) {
940 			netif_err(dev, ifup, dev->net,
941 				  "intr submit %d\n", retval);
942 			goto done;
943 		}
944 	}
945 
946 	set_bit(EVENT_DEV_OPEN, &dev->flags);
947 	netdev_reset_queue(net);
948 	netif_start_queue (net);
949 	netif_info(dev, ifup, dev->net,
950 		   "open: enable queueing (rx %d, tx %d) mtu %d %s framing\n",
951 		   (int)RX_QLEN(dev), (int)TX_QLEN(dev),
952 		   dev->net->mtu,
953 		   (dev->driver_info->flags & FLAG_FRAMING_NC) ? "NetChip" :
954 		   (dev->driver_info->flags & FLAG_FRAMING_GL) ? "GeneSys" :
955 		   (dev->driver_info->flags & FLAG_FRAMING_Z) ? "Zaurus" :
956 		   (dev->driver_info->flags & FLAG_FRAMING_RN) ? "RNDIS" :
957 		   (dev->driver_info->flags & FLAG_FRAMING_AX) ? "ASIX" :
958 		   "simple");
959 
960 	/* reset rx error state */
961 	dev->pkt_cnt = 0;
962 	dev->pkt_err = 0;
963 	clear_bit(EVENT_RX_KILL, &dev->flags);
964 
965 	// delay posting reads until we're fully open
966 	queue_work(system_bh_wq, &dev->bh_work);
967 	if (info->manage_power) {
968 		retval = info->manage_power(dev, 1);
969 		if (retval < 0) {
970 			retval = 0;
971 			set_bit(EVENT_NO_RUNTIME_PM, &dev->flags);
972 		} else {
973 			usb_autopm_put_interface(dev->intf);
974 		}
975 	}
976 	return retval;
977 done:
978 	usb_autopm_put_interface(dev->intf);
979 done_nopm:
980 	return retval;
981 }
982 EXPORT_SYMBOL_GPL(usbnet_open);
983 
984 /*-------------------------------------------------------------------------*/
985 
986 /* ethtool methods; minidrivers may need to add some more, but
987  * they'll probably want to use this base set.
988  */
989 
990 /* These methods are written on the assumption that the device
991  * uses MII
992  */
993 int usbnet_get_link_ksettings_mii(struct net_device *net,
994 			      struct ethtool_link_ksettings *cmd)
995 {
996 	struct usbnet *dev = netdev_priv(net);
997 
998 	if (!dev->mii.mdio_read)
999 		return -EOPNOTSUPP;
1000 
1001 	mii_ethtool_get_link_ksettings(&dev->mii, cmd);
1002 
1003 	return 0;
1004 }
1005 EXPORT_SYMBOL_GPL(usbnet_get_link_ksettings_mii);
1006 
1007 int usbnet_get_link_ksettings_internal(struct net_device *net,
1008 					struct ethtool_link_ksettings *cmd)
1009 {
1010 	struct usbnet *dev = netdev_priv(net);
1011 
1012 	/* the assumption that speed is equal on tx and rx
1013 	 * is deeply engrained into the networking layer.
1014 	 * For wireless stuff it is not true.
1015 	 * We assume that rx_speed matters more.
1016 	 */
1017 	if (dev->rx_speed != SPEED_UNSET)
1018 		cmd->base.speed = dev->rx_speed / 1000000;
1019 	else if (dev->tx_speed != SPEED_UNSET)
1020 		cmd->base.speed = dev->tx_speed / 1000000;
1021 	else
1022 		cmd->base.speed = SPEED_UNKNOWN;
1023 
1024 	/* The standard "Universal Serial Bus Class Definitions
1025 	 * for Communications Devices v1.2" does not specify
1026 	 * anything about duplex status.
1027 	 * So set it DUPLEX_UNKNOWN instead of default DUPLEX_HALF.
1028 	 */
1029 	cmd->base.duplex = DUPLEX_UNKNOWN;
1030 
1031 	return 0;
1032 }
1033 EXPORT_SYMBOL_GPL(usbnet_get_link_ksettings_internal);
1034 
1035 int usbnet_set_link_ksettings_mii(struct net_device *net,
1036 			      const struct ethtool_link_ksettings *cmd)
1037 {
1038 	struct usbnet *dev = netdev_priv(net);
1039 	int retval;
1040 
1041 	if (!dev->mii.mdio_write)
1042 		return -EOPNOTSUPP;
1043 
1044 	retval = mii_ethtool_set_link_ksettings(&dev->mii, cmd);
1045 
1046 	/* link speed/duplex might have changed */
1047 	if (dev->driver_info->link_reset)
1048 		dev->driver_info->link_reset(dev);
1049 
1050 	/* hard_mtu or rx_urb_size may change in link_reset() */
1051 	usbnet_update_max_qlen(dev);
1052 
1053 	return retval;
1054 }
1055 EXPORT_SYMBOL_GPL(usbnet_set_link_ksettings_mii);
1056 
1057 u32 usbnet_get_link(struct net_device *net)
1058 {
1059 	struct usbnet *dev = netdev_priv(net);
1060 
1061 	/* If a check_connect is defined, return its result */
1062 	if (dev->driver_info->check_connect)
1063 		return dev->driver_info->check_connect(dev) == 0;
1064 
1065 	/* if the device has mii operations, use those */
1066 	if (dev->mii.mdio_read)
1067 		return mii_link_ok(&dev->mii);
1068 
1069 	/* Otherwise, dtrt for drivers calling netif_carrier_{on,off} */
1070 	return ethtool_op_get_link(net);
1071 }
1072 EXPORT_SYMBOL_GPL(usbnet_get_link);
1073 
1074 int usbnet_nway_reset(struct net_device *net)
1075 {
1076 	struct usbnet *dev = netdev_priv(net);
1077 
1078 	if (!dev->mii.mdio_write)
1079 		return -EOPNOTSUPP;
1080 
1081 	return mii_nway_restart(&dev->mii);
1082 }
1083 EXPORT_SYMBOL_GPL(usbnet_nway_reset);
1084 
1085 int usbnet_mii_ioctl(struct net_device *net, struct ifreq *rq, int cmd)
1086 {
1087 	struct usbnet *dev = netdev_priv(net);
1088 
1089 	return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL);
1090 }
1091 EXPORT_SYMBOL_GPL(usbnet_mii_ioctl);
1092 
1093 void usbnet_get_drvinfo(struct net_device *net, struct ethtool_drvinfo *info)
1094 {
1095 	struct usbnet *dev = netdev_priv(net);
1096 
1097 	strscpy(info->driver, dev->driver_name, sizeof(info->driver));
1098 	strscpy(info->fw_version, dev->driver_info->description,
1099 		sizeof(info->fw_version));
1100 	usb_make_path(dev->udev, info->bus_info, sizeof(info->bus_info));
1101 }
1102 EXPORT_SYMBOL_GPL(usbnet_get_drvinfo);
1103 
1104 u32 usbnet_get_msglevel(struct net_device *net)
1105 {
1106 	struct usbnet *dev = netdev_priv(net);
1107 
1108 	return dev->msg_enable;
1109 }
1110 EXPORT_SYMBOL_GPL(usbnet_get_msglevel);
1111 
1112 void usbnet_set_msglevel(struct net_device *net, u32 level)
1113 {
1114 	struct usbnet *dev = netdev_priv(net);
1115 
1116 	dev->msg_enable = level;
1117 }
1118 EXPORT_SYMBOL_GPL(usbnet_set_msglevel);
1119 
1120 /* drivers may override default ethtool_ops in their bind() routine */
1121 static const struct ethtool_ops usbnet_ethtool_ops = {
1122 	.get_link		= usbnet_get_link,
1123 	.nway_reset		= usbnet_nway_reset,
1124 	.get_drvinfo		= usbnet_get_drvinfo,
1125 	.get_msglevel		= usbnet_get_msglevel,
1126 	.set_msglevel		= usbnet_set_msglevel,
1127 	.get_ts_info		= ethtool_op_get_ts_info,
1128 	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
1129 	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
1130 };
1131 
1132 /*-------------------------------------------------------------------------*/
1133 
1134 static void __handle_link_change(struct usbnet *dev)
1135 {
1136 	if (!test_bit(EVENT_DEV_OPEN, &dev->flags))
1137 		return;
1138 
1139 	if (test_and_clear_bit(EVENT_LINK_CARRIER_ON, &dev->flags))
1140 		netif_carrier_on(dev->net);
1141 
1142 	if (!netif_carrier_ok(dev->net)) {
1143 		/* kill URBs for reading packets to save bus bandwidth */
1144 		unlink_urbs(dev, &dev->rxq);
1145 
1146 		/*
1147 		 * tx_timeout will unlink URBs for sending packets and
1148 		 * tx queue is stopped by netcore after link becomes off
1149 		 */
1150 	} else {
1151 		/* submitting URBs for reading packets */
1152 		queue_work(system_bh_wq, &dev->bh_work);
1153 	}
1154 
1155 	/* hard_mtu or rx_urb_size may change during link change */
1156 	usbnet_update_max_qlen(dev);
1157 
1158 	clear_bit(EVENT_LINK_CHANGE, &dev->flags);
1159 }
1160 
1161 void usbnet_set_rx_mode(struct net_device *net)
1162 {
1163 	struct usbnet		*dev = netdev_priv(net);
1164 
1165 	usbnet_defer_kevent(dev, EVENT_SET_RX_MODE);
1166 }
1167 EXPORT_SYMBOL_GPL(usbnet_set_rx_mode);
1168 
1169 static void __handle_set_rx_mode(struct usbnet *dev)
1170 {
1171 	if (dev->driver_info->set_rx_mode)
1172 		(dev->driver_info->set_rx_mode)(dev);
1173 
1174 	clear_bit(EVENT_SET_RX_MODE, &dev->flags);
1175 }
1176 
1177 /* work that cannot be done in interrupt context uses keventd.
1178  *
1179  * NOTE:  with 2.5 we could do more of this using completion callbacks,
1180  * especially now that control transfers can be queued.
1181  */
1182 static void
1183 usbnet_deferred_kevent(struct work_struct *work)
1184 {
1185 	struct usbnet		*dev =
1186 		container_of(work, struct usbnet, kevent);
1187 	int			status;
1188 
1189 	/* usb_clear_halt() needs a thread context */
1190 	if (test_bit(EVENT_TX_HALT, &dev->flags)) {
1191 		unlink_urbs(dev, &dev->txq);
1192 		status = usb_autopm_get_interface(dev->intf);
1193 		if (status < 0)
1194 			goto fail_pipe;
1195 		status = usb_clear_halt(dev->udev, dev->out);
1196 		usb_autopm_put_interface(dev->intf);
1197 		if (status < 0 &&
1198 		    status != -EPIPE &&
1199 		    status != -ESHUTDOWN) {
1200 			if (netif_msg_tx_err(dev))
1201 fail_pipe:
1202 				netdev_err(dev->net, "can't clear tx halt, status %d\n",
1203 					   status);
1204 		} else {
1205 			clear_bit(EVENT_TX_HALT, &dev->flags);
1206 			if (status != -ESHUTDOWN)
1207 				netif_wake_queue(dev->net);
1208 		}
1209 	}
1210 	if (test_bit(EVENT_RX_HALT, &dev->flags)) {
1211 		unlink_urbs(dev, &dev->rxq);
1212 		status = usb_autopm_get_interface(dev->intf);
1213 		if (status < 0)
1214 			goto fail_halt;
1215 		status = usb_clear_halt(dev->udev, dev->in);
1216 		usb_autopm_put_interface(dev->intf);
1217 		if (status < 0 &&
1218 		    status != -EPIPE &&
1219 		    status != -ESHUTDOWN) {
1220 			if (netif_msg_rx_err(dev))
1221 fail_halt:
1222 				netdev_err(dev->net, "can't clear rx halt, status %d\n",
1223 					   status);
1224 		} else {
1225 			clear_bit(EVENT_RX_HALT, &dev->flags);
1226 			if (!usbnet_going_away(dev))
1227 				queue_work(system_bh_wq, &dev->bh_work);
1228 		}
1229 	}
1230 
1231 	/* work could resubmit itself forever if memory is tight */
1232 	if (test_bit(EVENT_RX_MEMORY, &dev->flags)) {
1233 		struct urb	*urb = NULL;
1234 		int resched = 1;
1235 
1236 		if (netif_running(dev->net))
1237 			urb = usb_alloc_urb(0, GFP_KERNEL);
1238 		else
1239 			clear_bit(EVENT_RX_MEMORY, &dev->flags);
1240 		if (urb != NULL) {
1241 			clear_bit(EVENT_RX_MEMORY, &dev->flags);
1242 			status = usb_autopm_get_interface(dev->intf);
1243 			if (status < 0) {
1244 				usb_free_urb(urb);
1245 				goto fail_lowmem;
1246 			}
1247 			if (rx_submit(dev, urb, GFP_KERNEL) == -ENOLINK)
1248 				resched = 0;
1249 			usb_autopm_put_interface(dev->intf);
1250 fail_lowmem:
1251 			if (resched)
1252 				if (!usbnet_going_away(dev))
1253 					queue_work(system_bh_wq, &dev->bh_work);
1254 		}
1255 	}
1256 
1257 	if (test_bit (EVENT_LINK_RESET, &dev->flags)) {
1258 		const struct driver_info *info = dev->driver_info;
1259 		int			retval = 0;
1260 
1261 		clear_bit(EVENT_LINK_RESET, &dev->flags);
1262 		status = usb_autopm_get_interface(dev->intf);
1263 		if (status < 0)
1264 			goto skip_reset;
1265 		if(info->link_reset && (retval = info->link_reset(dev)) < 0) {
1266 			usb_autopm_put_interface(dev->intf);
1267 skip_reset:
1268 			netdev_info(dev->net, "link reset failed (%d) usbnet usb-%s-%s, %s\n",
1269 				    retval,
1270 				    dev->udev->bus->bus_name,
1271 				    dev->udev->devpath,
1272 				    info->description);
1273 		} else {
1274 			usb_autopm_put_interface(dev->intf);
1275 		}
1276 
1277 		/* handle link change from link resetting */
1278 		__handle_link_change(dev);
1279 	}
1280 
1281 	if (test_bit(EVENT_LINK_CHANGE, &dev->flags))
1282 		__handle_link_change(dev);
1283 
1284 	if (test_bit(EVENT_SET_RX_MODE, &dev->flags))
1285 		__handle_set_rx_mode(dev);
1286 
1287 
1288 	if (dev->flags)
1289 		netdev_dbg(dev->net, "kevent done, flags = 0x%lx\n", dev->flags);
1290 }
1291 
1292 /*-------------------------------------------------------------------------*/
1293 
1294 static void tx_complete(struct urb *urb)
1295 {
1296 	struct sk_buff		*skb = (struct sk_buff *) urb->context;
1297 	struct skb_data		*entry = (struct skb_data *) skb->cb;
1298 	struct usbnet		*dev = entry->dev;
1299 
1300 	if (urb->status == 0) {
1301 		struct pcpu_sw_netstats *stats64 = this_cpu_ptr(dev->net->tstats);
1302 		unsigned long flags;
1303 
1304 		flags = u64_stats_update_begin_irqsave(&stats64->syncp);
1305 		u64_stats_add(&stats64->tx_packets, entry->packets);
1306 		u64_stats_add(&stats64->tx_bytes, entry->length);
1307 		u64_stats_update_end_irqrestore(&stats64->syncp, flags);
1308 	} else {
1309 		dev->net->stats.tx_errors++;
1310 
1311 		switch (urb->status) {
1312 		case -EPIPE:
1313 			usbnet_defer_kevent(dev, EVENT_TX_HALT);
1314 			break;
1315 
1316 		/* software-driven interface shutdown */
1317 		case -ECONNRESET:		// async unlink
1318 		case -ESHUTDOWN:		// hardware gone
1319 			break;
1320 
1321 		/* like rx, tx gets controller i/o faults during hub_wq
1322 		 * delays and so it uses the same throttling mechanism.
1323 		 */
1324 		case -EPROTO:
1325 		case -ETIME:
1326 		case -EILSEQ:
1327 			usb_mark_last_busy(dev->udev);
1328 			if (!timer_pending(&dev->delay)) {
1329 				mod_timer(&dev->delay,
1330 					  jiffies + THROTTLE_JIFFIES);
1331 				netif_dbg(dev, link, dev->net,
1332 					  "tx throttle %d\n", urb->status);
1333 			}
1334 			netif_stop_queue(dev->net);
1335 			break;
1336 		default:
1337 			netif_dbg(dev, tx_err, dev->net,
1338 				  "tx err %d\n", entry->urb->status);
1339 			break;
1340 		}
1341 	}
1342 
1343 	usb_autopm_put_interface_async(dev->intf);
1344 	(void) defer_bh(dev, skb, &dev->txq, tx_done);
1345 }
1346 
1347 /*-------------------------------------------------------------------------*/
1348 
1349 void usbnet_tx_timeout(struct net_device *net, unsigned int txqueue)
1350 {
1351 	struct usbnet		*dev = netdev_priv(net);
1352 
1353 	unlink_urbs(dev, &dev->txq);
1354 	queue_work(system_bh_wq, &dev->bh_work);
1355 	/* this needs to be handled individually because the generic layer
1356 	 * doesn't know what is sufficient and could not restore private
1357 	 * information if a remedy of an unconditional reset were used.
1358 	 */
1359 	if (dev->driver_info->recover)
1360 		(dev->driver_info->recover)(dev);
1361 }
1362 EXPORT_SYMBOL_GPL(usbnet_tx_timeout);
1363 
1364 /*-------------------------------------------------------------------------*/
1365 
1366 static int build_dma_sg(const struct sk_buff *skb, struct urb *urb)
1367 {
1368 	unsigned num_sgs, total_len = 0;
1369 	int i, s = 0;
1370 
1371 	num_sgs = skb_shinfo(skb)->nr_frags + 1;
1372 	if (num_sgs == 1)
1373 		return 0;
1374 
1375 	/* reserve one for zero packet */
1376 	urb->sg = kmalloc_objs(struct scatterlist, num_sgs + 1, GFP_ATOMIC);
1377 	if (!urb->sg)
1378 		return -ENOMEM;
1379 
1380 	urb->num_sgs = num_sgs;
1381 	sg_init_table(urb->sg, urb->num_sgs + 1);
1382 
1383 	sg_set_buf(&urb->sg[s++], skb->data, skb_headlen(skb));
1384 	total_len += skb_headlen(skb);
1385 
1386 	for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
1387 		skb_frag_t *f = &skb_shinfo(skb)->frags[i];
1388 
1389 		total_len += skb_frag_size(f);
1390 		sg_set_page(&urb->sg[i + s], skb_frag_page(f), skb_frag_size(f),
1391 			    skb_frag_off(f));
1392 	}
1393 	urb->transfer_buffer_length = total_len;
1394 
1395 	return 1;
1396 }
1397 
1398 netdev_tx_t usbnet_start_xmit(struct sk_buff *skb, struct net_device *net)
1399 {
1400 	struct usbnet		*dev = netdev_priv(net);
1401 	unsigned int			length;
1402 	struct urb		*urb = NULL;
1403 	struct skb_data		*entry;
1404 	const struct driver_info *info = dev->driver_info;
1405 	unsigned long		flags;
1406 	int retval;
1407 
1408 	if (skb)
1409 		skb_tx_timestamp(skb);
1410 
1411 	// some devices want funky USB-level framing, for
1412 	// win32 driver (usually) and/or hardware quirks
1413 	if (info->tx_fixup) {
1414 		skb = info->tx_fixup(dev, skb, GFP_ATOMIC);
1415 		if (!skb) {
1416 			/* packet collected; minidriver waiting for more */
1417 			if (info->flags & FLAG_MULTI_PACKET)
1418 				goto not_drop;
1419 			netif_dbg(dev, tx_err, dev->net, "can't tx_fixup skb\n");
1420 			goto drop;
1421 		}
1422 	}
1423 
1424 	urb = usb_alloc_urb(0, GFP_ATOMIC);
1425 	if (!urb) {
1426 		netif_dbg(dev, tx_err, dev->net, "no urb\n");
1427 		goto drop;
1428 	}
1429 
1430 	entry = (struct skb_data *) skb->cb;
1431 	entry->urb = urb;
1432 	entry->dev = dev;
1433 
1434 	usb_fill_bulk_urb(urb, dev->udev, dev->out,
1435 			  skb->data, skb->len, tx_complete, skb);
1436 	if (dev->can_dma_sg) {
1437 		if (build_dma_sg(skb, urb) < 0)
1438 			goto drop;
1439 	}
1440 	length = urb->transfer_buffer_length;
1441 
1442 	/* don't assume the hardware handles USB_ZERO_PACKET
1443 	 * NOTE:  strictly conforming cdc-ether devices should expect
1444 	 * the ZLP here, but ignore the one-byte packet.
1445 	 * NOTE2: CDC NCM specification is different from CDC ECM when
1446 	 * handling ZLP/short packets, so cdc_ncm driver will make short
1447 	 * packet itself if needed.
1448 	 */
1449 	if (length % dev->maxpacket == 0) {
1450 		if (!(info->flags & FLAG_SEND_ZLP)) {
1451 			if (!(info->flags & FLAG_MULTI_PACKET)) {
1452 				length++;
1453 				if (skb_tailroom(skb) && !urb->num_sgs) {
1454 					skb->data[skb->len] = 0;
1455 					__skb_put(skb, 1);
1456 				} else if (urb->num_sgs)
1457 					sg_set_buf(&urb->sg[urb->num_sgs++],
1458 							dev->padding_pkt, 1);
1459 			}
1460 		} else
1461 			urb->transfer_flags |= URB_ZERO_PACKET;
1462 	}
1463 	urb->transfer_buffer_length = length;
1464 
1465 	if (info->flags & FLAG_MULTI_PACKET) {
1466 		/* Driver has set number of packets and a length delta.
1467 		 * Calculate the complete length and ensure that it's
1468 		 * positive.
1469 		 */
1470 		entry->length += length;
1471 		if (WARN_ON_ONCE(entry->length <= 0))
1472 			entry->length = length;
1473 	} else {
1474 		usbnet_set_skb_tx_stats(skb, 1, length);
1475 	}
1476 
1477 	spin_lock_irqsave(&dev->txq.lock, flags);
1478 	retval = usb_autopm_get_interface_async(dev->intf);
1479 	if (retval < 0) {
1480 		spin_unlock_irqrestore(&dev->txq.lock, flags);
1481 		goto drop;
1482 	}
1483 	if (netif_queue_stopped(net)) {
1484 		usb_autopm_put_interface_async(dev->intf);
1485 		spin_unlock_irqrestore(&dev->txq.lock, flags);
1486 		goto drop;
1487 	}
1488 
1489 #ifdef CONFIG_PM
1490 	/* if this triggers the device is still a sleep */
1491 	if (test_bit(EVENT_DEV_ASLEEP, &dev->flags)) {
1492 		/* transmission will be done in resume */
1493 		usb_anchor_urb(urb, &dev->deferred);
1494 		/* no use to process more packets */
1495 		netif_stop_queue(net);
1496 		usb_put_urb(urb);
1497 		spin_unlock_irqrestore(&dev->txq.lock, flags);
1498 		netdev_dbg(dev->net, "Delaying transmission for resumption\n");
1499 		goto deferred;
1500 	}
1501 #endif
1502 
1503 	switch ((retval = usb_submit_urb (urb, GFP_ATOMIC))) {
1504 	case -EPIPE:
1505 		netif_stop_queue(net);
1506 		usbnet_defer_kevent(dev, EVENT_TX_HALT);
1507 		usb_autopm_put_interface_async(dev->intf);
1508 		break;
1509 	default:
1510 		usb_autopm_put_interface_async(dev->intf);
1511 		netif_dbg(dev, tx_err, dev->net,
1512 			  "tx: submit urb err %d\n", retval);
1513 		break;
1514 	case 0:
1515 		netif_trans_update(net);
1516 		__usbnet_queue_skb(&dev->txq, skb, tx_start);
1517 		netdev_sent_queue(net, skb->len);
1518 		if (dev->txq.qlen >= TX_QLEN (dev))
1519 			netif_stop_queue (net);
1520 	}
1521 	spin_unlock_irqrestore(&dev->txq.lock, flags);
1522 
1523 	if (retval) {
1524 		netif_dbg(dev, tx_err, dev->net, "drop, code %d\n", retval);
1525 drop:
1526 		dev->net->stats.tx_dropped++;
1527 not_drop:
1528 		if (skb)
1529 			dev_kfree_skb_any(skb);
1530 		if (urb) {
1531 			kfree(urb->sg);
1532 			usb_free_urb(urb);
1533 		}
1534 	} else
1535 		netif_dbg(dev, tx_queued, dev->net,
1536 			  "> tx, len %u, type 0x%x\n", length, skb->protocol);
1537 #ifdef CONFIG_PM
1538 deferred:
1539 #endif
1540 	return NETDEV_TX_OK;
1541 }
1542 EXPORT_SYMBOL_GPL(usbnet_start_xmit);
1543 
1544 static int rx_alloc_submit(struct usbnet *dev, gfp_t flags)
1545 {
1546 	struct urb	*urb;
1547 	int		i;
1548 	int		ret = 0;
1549 
1550 	/* don't refill the queue all at once */
1551 	for (i = 0; i < 10 && dev->rxq.qlen < RX_QLEN(dev); i++) {
1552 		urb = usb_alloc_urb(0, flags);
1553 		if (urb != NULL) {
1554 			ret = rx_submit(dev, urb, flags);
1555 			if (ret)
1556 				goto err;
1557 		} else {
1558 			ret = -ENOMEM;
1559 			goto err;
1560 		}
1561 	}
1562 err:
1563 	return ret;
1564 }
1565 
1566 static inline void usb_free_skb(struct sk_buff *skb)
1567 {
1568 	struct skb_data *entry = (struct skb_data *)skb->cb;
1569 
1570 	usb_free_urb(entry->urb);
1571 	dev_kfree_skb(skb);
1572 }
1573 
1574 /*-------------------------------------------------------------------------*/
1575 
1576 // work (work deferred from completions, in_irq) or timer
1577 
1578 static void usbnet_bh(struct timer_list *t)
1579 {
1580 	struct usbnet		*dev = timer_container_of(dev, t, delay);
1581 	unsigned int bytes_compl = 0, pkts_compl = 0;
1582 	struct sk_buff		*skb;
1583 	struct skb_data		*entry;
1584 
1585 	while ((skb = skb_dequeue (&dev->done))) {
1586 		entry = (struct skb_data *) skb->cb;
1587 		switch (entry->state) {
1588 		case rx_done:
1589 			if (rx_process(dev, skb))
1590 				usb_free_skb(skb);
1591 			continue;
1592 		case tx_done:
1593 			bytes_compl += skb->len;
1594 			pkts_compl++;
1595 			kfree(entry->urb->sg);
1596 			fallthrough;
1597 		case rx_cleanup:
1598 			usb_free_skb(skb);
1599 			continue;
1600 		default:
1601 			netdev_dbg(dev->net, "bogus skb state %d\n", entry->state);
1602 		}
1603 	}
1604 
1605 	spin_lock_bh(&dev->bql_spinlock);
1606 	netdev_completed_queue(dev->net, pkts_compl, bytes_compl);
1607 	spin_unlock_bh(&dev->bql_spinlock);
1608 
1609 	/* restart RX again after disabling due to high error rate */
1610 	clear_bit(EVENT_RX_KILL, &dev->flags);
1611 
1612 	/* waiting for all pending urbs to complete?
1613 	 * only then can we forgo submitting anew
1614 	 */
1615 	if (waitqueue_active(&dev->wait)) {
1616 		if (dev->txq.qlen + dev->rxq.qlen + dev->done.qlen == 0)
1617 			wake_up_all(&dev->wait);
1618 
1619 	// or are we maybe short a few urbs?
1620 	} else if (netif_running (dev->net) &&
1621 		   netif_device_present (dev->net) &&
1622 		   netif_carrier_ok(dev->net) &&
1623 		   !usbnet_going_away(dev) &&
1624 		   !timer_pending(&dev->delay) &&
1625 		   !test_bit(EVENT_RX_PAUSED, &dev->flags) &&
1626 		   !test_bit(EVENT_RX_HALT, &dev->flags)) {
1627 		int	temp = dev->rxq.qlen;
1628 
1629 		if (temp < RX_QLEN(dev)) {
1630 			if (rx_alloc_submit(dev, GFP_ATOMIC) == -ENOLINK)
1631 				return;
1632 			if (temp != dev->rxq.qlen)
1633 				netif_dbg(dev, link, dev->net,
1634 					  "rxqlen %d --> %d\n",
1635 					  temp, dev->rxq.qlen);
1636 			if (dev->rxq.qlen < RX_QLEN(dev))
1637 				queue_work(system_bh_wq, &dev->bh_work);
1638 		}
1639 		if (dev->txq.qlen < TX_QLEN (dev))
1640 			netif_wake_queue(dev->net);
1641 	}
1642 }
1643 
1644 static void usbnet_bh_work(struct work_struct *work)
1645 {
1646 	struct usbnet *dev = from_work(dev, work, bh_work);
1647 
1648 	usbnet_bh(&dev->delay);
1649 }
1650 
1651 
1652 /*-------------------------------------------------------------------------
1653  *
1654  * USB Device Driver support
1655  *
1656  *-------------------------------------------------------------------------*/
1657 
1658 // precondition: never called in_interrupt
1659 
1660 void usbnet_disconnect(struct usb_interface *intf)
1661 {
1662 	struct usbnet		*dev;
1663 	struct usb_device	*xdev;
1664 	struct net_device	*net;
1665 	struct urb		*urb;
1666 
1667 	dev = usb_get_intfdata(intf);
1668 	usb_set_intfdata(intf, NULL);
1669 	if (!dev)
1670 		return;
1671 	usbnet_mark_going_away(dev);
1672 
1673 	xdev = interface_to_usbdev(intf);
1674 
1675 	netif_info(dev, probe, dev->net, "unregister '%s' usb-%s-%s, %s\n",
1676 		   intf->dev.driver->name,
1677 		   xdev->bus->bus_name, xdev->devpath,
1678 		   dev->driver_info->description);
1679 
1680 	net = dev->net;
1681 	unregister_netdev(net);
1682 
1683 	cancel_work_sync(&dev->kevent);
1684 
1685 	while ((urb = usb_get_from_anchor(&dev->deferred))) {
1686 		dev_kfree_skb(urb->context);
1687 		kfree(urb->sg);
1688 		usb_free_urb(urb);
1689 	}
1690 
1691 	if (dev->driver_info->unbind)
1692 		dev->driver_info->unbind(dev, intf);
1693 
1694 	usb_kill_urb(dev->interrupt);
1695 	usb_free_urb(dev->interrupt);
1696 	kfree(dev->padding_pkt);
1697 
1698 	free_netdev(net);
1699 }
1700 EXPORT_SYMBOL_GPL(usbnet_disconnect);
1701 
1702 static const struct net_device_ops usbnet_netdev_ops = {
1703 	.ndo_open		= usbnet_open,
1704 	.ndo_stop		= usbnet_stop,
1705 	.ndo_start_xmit		= usbnet_start_xmit,
1706 	.ndo_tx_timeout		= usbnet_tx_timeout,
1707 	.ndo_set_rx_mode	= usbnet_set_rx_mode,
1708 	.ndo_change_mtu		= usbnet_change_mtu,
1709 	.ndo_set_mac_address 	= eth_mac_addr,
1710 	.ndo_validate_addr	= eth_validate_addr,
1711 };
1712 
1713 /*-------------------------------------------------------------------------*/
1714 
1715 // precondition: never called in_interrupt
1716 
1717 static const struct device_type wlan_type = {
1718 	.name	= "wlan",
1719 };
1720 
1721 static const struct device_type wwan_type = {
1722 	.name	= "wwan",
1723 };
1724 
1725 int
1726 usbnet_probe(struct usb_interface *udev, const struct usb_device_id *prod)
1727 {
1728 	struct usbnet			*dev;
1729 	struct net_device		*net;
1730 	struct usb_host_interface	*interface;
1731 	const struct driver_info	*info;
1732 	struct usb_device		*xdev;
1733 	int				status;
1734 	const char			*name;
1735 	struct usb_driver 	*driver = to_usb_driver(udev->dev.driver);
1736 
1737 	/* usbnet already took usb runtime pm, so have to enable the feature
1738 	 * for usb interface, otherwise usb_autopm_get_interface may return
1739 	 * failure if RUNTIME_PM is enabled.
1740 	 */
1741 	if (!driver->supports_autosuspend) {
1742 		driver->supports_autosuspend = 1;
1743 		pm_runtime_enable(&udev->dev);
1744 	}
1745 
1746 	name = udev->dev.driver->name;
1747 	info = (const struct driver_info *) prod->driver_info;
1748 	if (!info) {
1749 		dev_dbg (&udev->dev, "blacklisted by %s\n", name);
1750 		return -ENODEV;
1751 	}
1752 	xdev = interface_to_usbdev(udev);
1753 	interface = udev->cur_altsetting;
1754 
1755 	status = -ENOMEM;
1756 
1757 	// set up our own records
1758 	net = alloc_etherdev(sizeof(*dev));
1759 	if (!net)
1760 		goto out;
1761 
1762 	/* netdev_printk() needs this so do it as early as possible */
1763 	SET_NETDEV_DEV(net, &udev->dev);
1764 
1765 	dev = netdev_priv(net);
1766 	dev->udev = xdev;
1767 	dev->intf = udev;
1768 	dev->driver_info = info;
1769 	dev->driver_name = name;
1770 	dev->rx_speed = SPEED_UNSET;
1771 	dev->tx_speed = SPEED_UNSET;
1772 
1773 	dev->msg_enable = netif_msg_init (msg_level, NETIF_MSG_DRV
1774 				| NETIF_MSG_PROBE | NETIF_MSG_LINK);
1775 	init_waitqueue_head(&dev->wait);
1776 	skb_queue_head_init (&dev->rxq);
1777 	skb_queue_head_init (&dev->txq);
1778 	skb_queue_head_init (&dev->done);
1779 	skb_queue_head_init(&dev->rxq_pause);
1780 	spin_lock_init(&dev->bql_spinlock);
1781 	INIT_WORK(&dev->bh_work, usbnet_bh_work);
1782 	INIT_WORK(&dev->kevent, usbnet_deferred_kevent);
1783 	init_usb_anchor(&dev->deferred);
1784 	timer_setup(&dev->delay, usbnet_bh, 0);
1785 	mutex_init(&dev->phy_mutex);
1786 	mutex_init(&dev->interrupt_mutex);
1787 	dev->interrupt_count = 0;
1788 
1789 	dev->net = net;
1790 	strscpy(net->name, "usb%d", sizeof(net->name));
1791 
1792 	/* rx and tx sides can use different message sizes;
1793 	 * bind() should set rx_urb_size in that case.
1794 	 */
1795 	dev->hard_mtu = net->mtu + net->hard_header_len;
1796 	net->min_mtu = 0;
1797 	net->max_mtu = ETH_MAX_MTU;
1798 
1799 	net->netdev_ops = &usbnet_netdev_ops;
1800 	net->watchdog_timeo = TX_TIMEOUT_JIFFIES;
1801 	net->ethtool_ops = &usbnet_ethtool_ops;
1802 	net->pcpu_stat_type = NETDEV_PCPU_STAT_TSTATS;
1803 
1804 	// allow device-specific bind/init procedures
1805 	// NOTE net->name still not usable ...
1806 	if (info->bind) {
1807 		status = info->bind(dev, udev);
1808 		if (status < 0)
1809 			goto out1;
1810 
1811 		/* heuristic: rename to "eth%d" if we are not sure this link
1812 		 * is two-host (these links keep "usb%d")
1813 		 */
1814 		if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
1815 		    !usbnet_needs_usb_name_format(dev, net))
1816 			strscpy(net->name, "eth%d", sizeof(net->name));
1817 		/* WLAN devices should always be named "wlan%d" */
1818 		if ((dev->driver_info->flags & FLAG_WLAN) != 0)
1819 			strscpy(net->name, "wlan%d", sizeof(net->name));
1820 		/* WWAN devices should always be named "wwan%d" */
1821 		if ((dev->driver_info->flags & FLAG_WWAN) != 0)
1822 			strscpy(net->name, "wwan%d", sizeof(net->name));
1823 
1824 		/* devices that cannot do ARP */
1825 		if ((dev->driver_info->flags & FLAG_NOARP) != 0)
1826 			net->flags |= IFF_NOARP;
1827 
1828 		if ((dev->driver_info->flags & FLAG_NOMAXMTU) == 0 &&
1829 		    net->max_mtu > (dev->hard_mtu - net->hard_header_len))
1830 			net->max_mtu = dev->hard_mtu - net->hard_header_len;
1831 
1832 		if (net->mtu > (dev->hard_mtu - net->hard_header_len))
1833 			net->mtu = dev->hard_mtu - net->hard_header_len;
1834 
1835 	} else if (!info->in || !info->out)
1836 		status = usbnet_get_endpoints(dev, udev);
1837 	else {
1838 		u8 ep_addrs[3] = {
1839 			info->in + USB_DIR_IN, info->out + USB_DIR_OUT, 0
1840 		};
1841 
1842 		dev->in = usb_rcvbulkpipe(xdev, info->in);
1843 		dev->out = usb_sndbulkpipe(xdev, info->out);
1844 		if (!(info->flags & FLAG_NO_SETINT))
1845 			status = usb_set_interface(xdev,
1846 						   interface->desc.bInterfaceNumber,
1847 						   interface->desc.bAlternateSetting);
1848 		else
1849 			status = 0;
1850 
1851 		if (status == 0 && !usb_check_bulk_endpoints(udev, ep_addrs))
1852 			status = -EINVAL;
1853 	}
1854 	if (status >= 0 && dev->status)
1855 		status = init_status(dev, udev);
1856 	if (status < 0)
1857 		goto out3;
1858 
1859 	if (!dev->rx_urb_size)
1860 		dev->rx_urb_size = dev->hard_mtu;
1861 	dev->maxpacket = usb_maxpacket(dev->udev, dev->out);
1862 	if (dev->maxpacket == 0) {
1863 		/* that is a broken device */
1864 		status = -ENODEV;
1865 		goto out4;
1866 	}
1867 
1868 	/* this flags the device for user space */
1869 	if (!is_valid_ether_addr(net->dev_addr))
1870 		eth_hw_addr_random(net);
1871 
1872 	if ((dev->driver_info->flags & FLAG_WLAN) != 0)
1873 		SET_NETDEV_DEVTYPE(net, &wlan_type);
1874 	if ((dev->driver_info->flags & FLAG_WWAN) != 0)
1875 		SET_NETDEV_DEVTYPE(net, &wwan_type);
1876 
1877 	/* initialize max rx_qlen and tx_qlen */
1878 	usbnet_update_max_qlen(dev);
1879 
1880 	if (dev->can_dma_sg && !(info->flags & FLAG_SEND_ZLP) &&
1881 		!(info->flags & FLAG_MULTI_PACKET)) {
1882 		dev->padding_pkt = kzalloc(1, GFP_KERNEL);
1883 		if (!dev->padding_pkt) {
1884 			status = -ENOMEM;
1885 			goto out4;
1886 		}
1887 	}
1888 
1889 	status = register_netdev(net);
1890 	if (status)
1891 		goto out5;
1892 	netif_info(dev, probe, dev->net,
1893 		   "register '%s' at usb-%s-%s, %s, %pM\n",
1894 		   udev->dev.driver->name,
1895 		   xdev->bus->bus_name, xdev->devpath,
1896 		   dev->driver_info->description,
1897 		   net->dev_addr);
1898 
1899 	// ok, it's ready to go.
1900 	usb_set_intfdata(udev, dev);
1901 
1902 	netif_device_attach(net);
1903 
1904 	if (dev->driver_info->flags & FLAG_LINK_INTR)
1905 		usbnet_link_change(dev, 0, 0);
1906 
1907 	return 0;
1908 
1909 out5:
1910 	kfree(dev->padding_pkt);
1911 out4:
1912 	usb_free_urb(dev->interrupt);
1913 out3:
1914 	if (info->unbind)
1915 		info->unbind(dev, udev);
1916 out1:
1917 	/* subdrivers must undo all they did in bind() if they
1918 	 * fail it, but we may fail later and a deferred kevent
1919 	 * may trigger an error resubmitting itself and, worse,
1920 	 * schedule a timer. So we kill it all just in case.
1921 	 */
1922 	usbnet_mark_going_away(dev);
1923 	cancel_work_sync(&dev->kevent);
1924 	timer_delete_sync(&dev->delay);
1925 	free_netdev(net);
1926 out:
1927 	return status;
1928 }
1929 EXPORT_SYMBOL_GPL(usbnet_probe);
1930 
1931 /*-------------------------------------------------------------------------*/
1932 
1933 /*
1934  * suspend the whole driver as soon as the first interface is suspended
1935  * resume only when the last interface is resumed
1936  */
1937 
1938 int usbnet_suspend(struct usb_interface *intf, pm_message_t message)
1939 {
1940 	struct usbnet		*dev = usb_get_intfdata(intf);
1941 
1942 	if (!dev->suspend_count++) {
1943 		spin_lock_irq(&dev->txq.lock);
1944 		/* don't autosuspend while transmitting */
1945 		if (dev->txq.qlen && PMSG_IS_AUTO(message)) {
1946 			dev->suspend_count--;
1947 			spin_unlock_irq(&dev->txq.lock);
1948 			return -EBUSY;
1949 		} else {
1950 			set_bit(EVENT_DEV_ASLEEP, &dev->flags);
1951 			spin_unlock_irq(&dev->txq.lock);
1952 		}
1953 		/*
1954 		 * accelerate emptying of the rx and queues, to avoid
1955 		 * having everything error out.
1956 		 */
1957 		netif_device_detach(dev->net);
1958 		usbnet_terminate_urbs(dev);
1959 		__usbnet_status_stop_force(dev);
1960 
1961 		/*
1962 		 * reattach so runtime management can use and
1963 		 * wake the device
1964 		 */
1965 		netif_device_attach(dev->net);
1966 	}
1967 	return 0;
1968 }
1969 EXPORT_SYMBOL_GPL(usbnet_suspend);
1970 
1971 int usbnet_resume(struct usb_interface *intf)
1972 {
1973 	struct usbnet		*dev = usb_get_intfdata(intf);
1974 	struct sk_buff          *skb;
1975 	struct urb              *res;
1976 	int                     retval;
1977 
1978 	if (!--dev->suspend_count) {
1979 		/* resume interrupt URB if it was previously submitted */
1980 		__usbnet_status_start_force(dev, GFP_NOIO);
1981 
1982 		spin_lock_irq(&dev->txq.lock);
1983 		while ((res = usb_get_from_anchor(&dev->deferred))) {
1984 
1985 			skb = (struct sk_buff *)res->context;
1986 			retval = usb_submit_urb(res, GFP_ATOMIC);
1987 			if (retval < 0) {
1988 				dev_kfree_skb_any(skb);
1989 				kfree(res->sg);
1990 				usb_free_urb(res);
1991 				usb_autopm_put_interface_async(dev->intf);
1992 			} else {
1993 				netif_trans_update(dev->net);
1994 				__skb_queue_tail(&dev->txq, skb);
1995 				netdev_sent_queue(dev->net, skb->len);
1996 			}
1997 		}
1998 
1999 		smp_mb();
2000 		clear_bit(EVENT_DEV_ASLEEP, &dev->flags);
2001 		spin_unlock_irq(&dev->txq.lock);
2002 
2003 		if (test_bit(EVENT_DEV_OPEN, &dev->flags)) {
2004 			/* handle remote wakeup ASAP
2005 			 * we cannot race against stop
2006 			 */
2007 			if (netif_device_present(dev->net) &&
2008 				!timer_pending(&dev->delay) &&
2009 				!test_bit(EVENT_RX_HALT, &dev->flags))
2010 					rx_alloc_submit(dev, GFP_NOIO);
2011 
2012 			if (!(dev->txq.qlen >= TX_QLEN(dev)))
2013 				netif_tx_wake_all_queues(dev->net);
2014 			queue_work(system_bh_wq, &dev->bh_work);
2015 		}
2016 	}
2017 
2018 	if (test_and_clear_bit(EVENT_DEVICE_REPORT_IDLE, &dev->flags))
2019 		usb_autopm_get_interface_no_resume(intf);
2020 
2021 	return 0;
2022 }
2023 EXPORT_SYMBOL_GPL(usbnet_resume);
2024 
2025 /*
2026  * Either a subdriver implements manage_power, then it is assumed to always
2027  * be ready to be suspended or it reports the readiness to be suspended
2028  * explicitly
2029  */
2030 void usbnet_device_suggests_idle(struct usbnet *dev)
2031 {
2032 	if (!test_and_set_bit(EVENT_DEVICE_REPORT_IDLE, &dev->flags)) {
2033 		dev->intf->needs_remote_wakeup = 1;
2034 		usb_autopm_put_interface_async(dev->intf);
2035 	}
2036 }
2037 EXPORT_SYMBOL(usbnet_device_suggests_idle);
2038 
2039 /*
2040  * For devices that can do without special commands
2041  */
2042 int usbnet_manage_power(struct usbnet *dev, int on)
2043 {
2044 	dev->intf->needs_remote_wakeup = on;
2045 	return 0;
2046 }
2047 EXPORT_SYMBOL(usbnet_manage_power);
2048 
2049 void usbnet_link_change(struct usbnet *dev, bool link, bool need_reset)
2050 {
2051 	/* update link after link is reseted */
2052 	if (link && !need_reset) {
2053 		set_bit(EVENT_LINK_CARRIER_ON, &dev->flags);
2054 	} else {
2055 		clear_bit(EVENT_LINK_CARRIER_ON, &dev->flags);
2056 		netif_carrier_off(dev->net);
2057 	}
2058 
2059 	if (need_reset && link)
2060 		usbnet_defer_kevent(dev, EVENT_LINK_RESET);
2061 	else
2062 		usbnet_defer_kevent(dev, EVENT_LINK_CHANGE);
2063 }
2064 EXPORT_SYMBOL(usbnet_link_change);
2065 
2066 /*-------------------------------------------------------------------------*/
2067 static int __usbnet_read_cmd(struct usbnet *dev, u8 cmd, u8 reqtype,
2068 			     u16 value, u16 index, void *data, u16 size)
2069 {
2070 	void *buf = NULL;
2071 	int err = -ENOMEM;
2072 
2073 	netdev_dbg(dev->net, "usbnet_read_cmd cmd=0x%02x reqtype=%02x"
2074 		   " value=0x%04x index=0x%04x size=%d\n",
2075 		   cmd, reqtype, value, index, size);
2076 
2077 	if (size) {
2078 		buf = kmalloc(size, GFP_NOIO);
2079 		if (!buf)
2080 			goto out;
2081 	}
2082 
2083 	err = usb_control_msg(dev->udev, usb_rcvctrlpipe(dev->udev, 0),
2084 			      cmd, reqtype, value, index, buf, size,
2085 			      USB_CTRL_GET_TIMEOUT);
2086 	if (err > 0 && err <= size) {
2087 		if (data)
2088 			memcpy(data, buf, err);
2089 		else
2090 			netdev_dbg(dev->net,
2091 				   "Huh? Data requested but thrown away.\n");
2092 	}
2093 	kfree(buf);
2094 out:
2095 	return err;
2096 }
2097 
2098 static int __usbnet_write_cmd(struct usbnet *dev, u8 cmd, u8 reqtype,
2099 			      u16 value, u16 index, const void *data,
2100 			      u16 size)
2101 {
2102 	void *buf = NULL;
2103 	int err = -ENOMEM;
2104 
2105 	netdev_dbg(dev->net, "usbnet_write_cmd cmd=0x%02x reqtype=%02x"
2106 		   " value=0x%04x index=0x%04x size=%d\n",
2107 		   cmd, reqtype, value, index, size);
2108 
2109 	if (data) {
2110 		buf = kmemdup(data, size, GFP_NOIO);
2111 		if (!buf)
2112 			goto out;
2113 	} else {
2114         if (size) {
2115             WARN_ON_ONCE(1);
2116             err = -EINVAL;
2117             goto out;
2118         }
2119     }
2120 
2121 	err = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0),
2122 			      cmd, reqtype, value, index, buf, size,
2123 			      USB_CTRL_SET_TIMEOUT);
2124 	kfree(buf);
2125 
2126 out:
2127 	return err;
2128 }
2129 
2130 /*
2131  * The function can't be called inside suspend/resume callback,
2132  * otherwise deadlock will be caused.
2133  */
2134 int usbnet_read_cmd(struct usbnet *dev, u8 cmd, u8 reqtype,
2135 		    u16 value, u16 index, void *data, u16 size)
2136 {
2137 	int ret;
2138 
2139 	if (usb_autopm_get_interface(dev->intf) < 0)
2140 		return -ENODEV;
2141 	ret = __usbnet_read_cmd(dev, cmd, reqtype, value, index,
2142 				data, size);
2143 	usb_autopm_put_interface(dev->intf);
2144 	return ret;
2145 }
2146 EXPORT_SYMBOL_GPL(usbnet_read_cmd);
2147 
2148 /*
2149  * The function can't be called inside suspend/resume callback,
2150  * otherwise deadlock will be caused.
2151  */
2152 int usbnet_write_cmd(struct usbnet *dev, u8 cmd, u8 reqtype,
2153 		     u16 value, u16 index, const void *data, u16 size)
2154 {
2155 	int ret;
2156 
2157 	if (usb_autopm_get_interface(dev->intf) < 0)
2158 		return -ENODEV;
2159 	ret = __usbnet_write_cmd(dev, cmd, reqtype, value, index,
2160 				 data, size);
2161 	usb_autopm_put_interface(dev->intf);
2162 	return ret;
2163 }
2164 EXPORT_SYMBOL_GPL(usbnet_write_cmd);
2165 
2166 /*
2167  * The function can be called inside suspend/resume callback safely
2168  * and should only be called by suspend/resume callback generally.
2169  */
2170 int usbnet_read_cmd_nopm(struct usbnet *dev, u8 cmd, u8 reqtype,
2171 			  u16 value, u16 index, void *data, u16 size)
2172 {
2173 	return __usbnet_read_cmd(dev, cmd, reqtype, value, index,
2174 				 data, size);
2175 }
2176 EXPORT_SYMBOL_GPL(usbnet_read_cmd_nopm);
2177 
2178 /*
2179  * The function can be called inside suspend/resume callback safely
2180  * and should only be called by suspend/resume callback generally.
2181  */
2182 int usbnet_write_cmd_nopm(struct usbnet *dev, u8 cmd, u8 reqtype,
2183 			  u16 value, u16 index, const void *data,
2184 			  u16 size)
2185 {
2186 	return __usbnet_write_cmd(dev, cmd, reqtype, value, index,
2187 				  data, size);
2188 }
2189 EXPORT_SYMBOL_GPL(usbnet_write_cmd_nopm);
2190 
2191 static void usbnet_async_cmd_cb(struct urb *urb)
2192 {
2193 	struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context;
2194 	int status = urb->status;
2195 
2196 	if (status < 0)
2197 		dev_dbg(&urb->dev->dev, "%s failed with %d",
2198 			__func__, status);
2199 
2200 	kfree(req);
2201 	usb_free_urb(urb);
2202 }
2203 
2204 /*
2205  * The caller must make sure that device can't be put into suspend
2206  * state until the control URB completes.
2207  */
2208 int usbnet_write_cmd_async(struct usbnet *dev, u8 cmd, u8 reqtype,
2209 			   u16 value, u16 index, const void *data, u16 size)
2210 {
2211 	struct usb_ctrlrequest *req;
2212 	struct urb *urb;
2213 	int err = -ENOMEM;
2214 	void *buf = NULL;
2215 
2216 	netdev_dbg(dev->net, "usbnet_write_cmd cmd=0x%02x reqtype=%02x"
2217 		   " value=0x%04x index=0x%04x size=%d\n",
2218 		   cmd, reqtype, value, index, size);
2219 
2220 	urb = usb_alloc_urb(0, GFP_ATOMIC);
2221 	if (!urb)
2222 		goto fail;
2223 
2224 	if (data) {
2225 		buf = kmemdup(data, size, GFP_ATOMIC);
2226 		if (!buf) {
2227 			netdev_err(dev->net, "Error allocating buffer"
2228 				   " in %s!\n", __func__);
2229 			goto fail_free_urb;
2230 		}
2231 	}
2232 
2233 	req = kmalloc_obj(struct usb_ctrlrequest, GFP_ATOMIC);
2234 	if (!req)
2235 		goto fail_free_buf;
2236 
2237 	req->bRequestType = reqtype;
2238 	req->bRequest = cmd;
2239 	req->wValue = cpu_to_le16(value);
2240 	req->wIndex = cpu_to_le16(index);
2241 	req->wLength = cpu_to_le16(size);
2242 
2243 	usb_fill_control_urb(urb, dev->udev,
2244 			     usb_sndctrlpipe(dev->udev, 0),
2245 			     (void *)req, buf, size,
2246 			     usbnet_async_cmd_cb, req);
2247 	urb->transfer_flags |= URB_FREE_BUFFER;
2248 
2249 	err = usb_submit_urb(urb, GFP_ATOMIC);
2250 	if (err < 0) {
2251 		netdev_err(dev->net, "Error submitting the control"
2252 			   " message: status=%d\n", err);
2253 		goto fail_free_all;
2254 	}
2255 	return 0;
2256 
2257 fail_free_all:
2258 	kfree(req);
2259 fail_free_buf:
2260 	kfree(buf);
2261 	/*
2262 	 * avoid a double free
2263 	 * needed because the flag can be set only
2264 	 * after filling the URB
2265 	 */
2266 	urb->transfer_flags = 0;
2267 fail_free_urb:
2268 	usb_free_urb(urb);
2269 fail:
2270 	return err;
2271 
2272 }
2273 EXPORT_SYMBOL_GPL(usbnet_write_cmd_async);
2274 /*-------------------------------------------------------------------------*/
2275 
2276 static int __init usbnet_init(void)
2277 {
2278 	/* Compiler should optimize this out. */
2279 	BUILD_BUG_ON(
2280 		sizeof_field(struct sk_buff, cb) < sizeof(struct skb_data));
2281 
2282 	return 0;
2283 }
2284 module_init(usbnet_init);
2285 
2286 static void __exit usbnet_exit(void)
2287 {
2288 }
2289 module_exit(usbnet_exit);
2290 
2291 MODULE_AUTHOR("David Brownell");
2292 MODULE_DESCRIPTION("USB network driver framework");
2293 MODULE_LICENSE("GPL");
2294