1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3
4 bttv-cards.c
5
6 this file has configuration information - card-specific stuff
7 like the big tvcards array for the most part
8
9 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de)
10 & Marcus Metzler (mocm@thp.uni-koeln.de)
11 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
12
13
14 */
15
16 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
17
18 #include <linux/delay.h>
19 #include <linux/module.h>
20 #include <linux/kmod.h>
21 #include <linux/init.h>
22 #include <linux/pci.h>
23 #include <linux/vmalloc.h>
24 #include <linux/firmware.h>
25 #include <net/checksum.h>
26
27 #include <linux/unaligned.h>
28 #include <asm/io.h>
29
30 #include "bttvp.h"
31 #include <media/v4l2-common.h>
32 #include <media/i2c/tvaudio.h>
33 #include "bttv-audio-hook.h"
34
35 /* fwd decl */
36 static void boot_msp34xx(struct bttv *btv, int pin);
37 static void hauppauge_eeprom(struct bttv *btv);
38 static void avermedia_eeprom(struct bttv *btv);
39 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]);
40 static void modtec_eeprom(struct bttv *btv);
41 static void init_PXC200(struct bttv *btv);
42 static void init_RTV24(struct bttv *btv);
43 static void init_PCI8604PW(struct bttv *btv);
44
45 static void rv605_muxsel(struct bttv *btv, unsigned int input);
46 static void eagle_muxsel(struct bttv *btv, unsigned int input);
47 static void xguard_muxsel(struct bttv *btv, unsigned int input);
48 static void ivc120_muxsel(struct bttv *btv, unsigned int input);
49 static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
50
51 static void PXC200_muxsel(struct bttv *btv, unsigned int input);
52
53 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
54 static void picolo_tetra_init(struct bttv *btv);
55
56 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
57 static void tibetCS16_init(struct bttv *btv);
58
59 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
60 static void kodicom4400r_init(struct bttv *btv);
61
62 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
63 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
64
65 static void geovision_muxsel(struct bttv *btv, unsigned int input);
66
67 static void phytec_muxsel(struct bttv *btv, unsigned int input);
68
69 static void gv800s_muxsel(struct bttv *btv, unsigned int input);
70 static void gv800s_init(struct bttv *btv);
71
72 static void td3116_muxsel(struct bttv *btv, unsigned int input);
73
74 static int terratec_active_radio_upgrade(struct bttv *btv);
75 static int tea575x_init(struct bttv *btv);
76 static void identify_by_eeprom(struct bttv *btv,
77 unsigned char eeprom_data[256]);
78 static int pvr_boot(struct bttv *btv);
79
80 /* config variables */
81 static unsigned int triton1;
82 static unsigned int vsfx;
83 static unsigned int latency = UNSET;
84
85 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
86 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
87 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
88 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
89 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
90 static unsigned int audiodev[BTTV_MAX];
91 static unsigned int saa6588[BTTV_MAX];
92 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
93 static unsigned int autoload = UNSET;
94 static unsigned int gpiomask = UNSET;
95 static unsigned int audioall = UNSET;
96 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
97
98 /* insmod options */
99 module_param(triton1, int, 0444);
100 module_param(vsfx, int, 0444);
101 module_param(latency, int, 0444);
102 module_param(gpiomask, int, 0444);
103 module_param(audioall, int, 0444);
104 module_param(autoload, int, 0444);
105
106 module_param_array(card, int, NULL, 0444);
107 module_param_array(pll, int, NULL, 0444);
108 module_param_array(tuner, int, NULL, 0444);
109 module_param_array(svhs, int, NULL, 0444);
110 module_param_array(remote, int, NULL, 0444);
111 module_param_array(audiodev, int, NULL, 0444);
112 module_param_array(audiomux, int, NULL, 0444);
113
114 MODULE_PARM_DESC(triton1, "set ETBF pci config bit [enable bug compatibility for triton1 + others]");
115 MODULE_PARM_DESC(vsfx, "set VSFX pci config bit [yet another chipset flaw workaround]");
116 MODULE_PARM_DESC(latency,"pci latency timer");
117 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
118 MODULE_PARM_DESC(pll, "specify installed crystal (0=none, 28=28 MHz, 35=35 MHz, 14=14 MHz)");
119 MODULE_PARM_DESC(tuner,"specify installed tuner type");
120 MODULE_PARM_DESC(autoload, "obsolete option, please do not use anymore");
121 MODULE_PARM_DESC(audiodev, "specify audio device:\n"
122 "\t\t-1 = no audio\n"
123 "\t\t 0 = autodetect (default)\n"
124 "\t\t 1 = msp3400\n"
125 "\t\t 2 = tda7432\n"
126 "\t\t 3 = tvaudio");
127 MODULE_PARM_DESC(saa6588, "if 1, then load the saa6588 RDS module, default (0) is to use the card definition.");
128
129 MODULE_FIRMWARE("hcwamc.rbf");
130
131 /* I2C addresses list */
132 #define I2C_ADDR_TDA7432 0x8a
133 #define I2C_ADDR_MSP3400 0x80
134 #define I2C_ADDR_MSP3400_ALT 0x88
135
136
137 /* ----------------------------------------------------------------------- */
138 /* list of card IDs for bt878+ cards */
139
140 static struct CARD {
141 unsigned id;
142 int cardnr;
143 char *name;
144 } cards[] = {
145 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" },
146 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" },
147 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" },
148 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" },
149 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" },
150 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" },
151 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" },
152 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" },
153 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" },
154
155 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" },
156 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
157
158 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
159 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" },
160 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" },
161 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
162 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
163 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" },
164 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" },
165 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
166 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
167
168 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
169 /* some cards ship with byteswapped IDs ... */
170 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
171 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
172 /* this seems to happen as well ... */
173 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
174
175 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" },
176 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" },
177 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" },
178
179 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
180 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" },
181 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
182 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
183 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" },
184 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" },
185 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" },
186
187 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
188 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" },
189 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
190 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" },
191 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" },
192
193 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" },
194 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" },
195 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" },
196 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" },
197
198 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" },
199 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" },
200 /* clashes with FlyVideo
201 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */
202 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" },
203 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */
204 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */
205 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */
206
207 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
208 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
209 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
210 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
211 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
212
213 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" },
214 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" },
215 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" },
216 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" },
217 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" },
218
219 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" },
220 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" },
221 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" },
222 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" },
223
224 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" },
225 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" },
226 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" },
227 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" },
228
229 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" },
230 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" },
231 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" },
232 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" },
233 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" },
234 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" },
235 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" },
236 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" },
237 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" },
238 { 0xa1550800, BTTV_BOARD_IVC200, "IVC-200" },
239 { 0xa1550801, BTTV_BOARD_IVC200, "IVC-200" },
240 { 0xa1550802, BTTV_BOARD_IVC200, "IVC-200" },
241 { 0xa1550803, BTTV_BOARD_IVC200, "IVC-200" },
242 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" },
243 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" },
244 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" },
245 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" },
246 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" },
247 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" },
248 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" },
249 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" },
250 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" },
251 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" },
252 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" },
253 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" },
254 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" },
255 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" },
256 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" },
257 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" },
258 { 0xf0500000, BTTV_BOARD_IVCE8784, "IVCE-8784" },
259 { 0xf0500001, BTTV_BOARD_IVCE8784, "IVCE-8784" },
260 { 0xf0500002, BTTV_BOARD_IVCE8784, "IVCE-8784" },
261 { 0xf0500003, BTTV_BOARD_IVCE8784, "IVCE-8784" },
262
263 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" },
264 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" },
265
266 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
267 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
268 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" },
269 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
270 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
271 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" },
272
273 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" },
274 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
275
276 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" },
277 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
278 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
279 { 0x03116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 311" },
280 { 0x06116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 611" },
281 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" },
282 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" },
283 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" },
284 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" },
285 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" },
286
287 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" },
288 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" },
289
290 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
291 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
292 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
293 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
294
295 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" },
296
297 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" },
298 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" },
299
300 /* likely broken, vendor id doesn't match the other magic views ...
301 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */
302
303 /* Duplicate PCI ID, reconfigure for this board during the eeprom read.
304 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */
305
306 { 0x109e036e, BTTV_BOARD_CONCEPTRONIC_CTVFMI2, "Conceptronic CTVFMi v2"},
307
308 /* DVB cards (using pci function .1 for mpeg data xfer) */
309 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" },
310 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
311 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"},
312 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" },
313 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" },
314 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" },
315 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" },
316 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" },
317 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" },
318 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" },
319 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" },
320 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "},
321 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" },
322 { 0x763c008a, BTTV_BOARD_GEOVISION_GV600, "GeoVision GV-600" },
323 { 0x18011000, BTTV_BOARD_ENLTV_FM_2, "Encore ENL TV-FM-2" },
324 { 0x763d800a, BTTV_BOARD_GEOVISION_GV800S, "GeoVision GV-800(S) (master)" },
325 { 0x763d800b, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
326 { 0x763d800c, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
327 { 0x763d800d, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
328
329 { 0x15401830, BTTV_BOARD_PV183, "Provideo PV183-1" },
330 { 0x15401831, BTTV_BOARD_PV183, "Provideo PV183-2" },
331 { 0x15401832, BTTV_BOARD_PV183, "Provideo PV183-3" },
332 { 0x15401833, BTTV_BOARD_PV183, "Provideo PV183-4" },
333 { 0x15401834, BTTV_BOARD_PV183, "Provideo PV183-5" },
334 { 0x15401835, BTTV_BOARD_PV183, "Provideo PV183-6" },
335 { 0x15401836, BTTV_BOARD_PV183, "Provideo PV183-7" },
336 { 0x15401837, BTTV_BOARD_PV183, "Provideo PV183-8" },
337 { 0x3116f200, BTTV_BOARD_TVT_TD3116, "Tongwei Video Technology TD-3116" },
338 { 0x02280279, BTTV_BOARD_APOSONIC_WDVR, "Aposonic W-DVR" },
339 { 0, -1, NULL }
340 };
341
342 /* ----------------------------------------------------------------------- */
343 /* array with description for bt848 / bt878 tv/grabber cards */
344
345 struct tvcard bttv_tvcards[] = {
346 /* ---- card 0x00 ---------------------------------- */
347 [BTTV_BOARD_UNKNOWN] = {
348 .name = " *** UNKNOWN/GENERIC *** ",
349 .video_inputs = 4,
350 .svhs = 2,
351 .muxsel = MUXSEL(2, 3, 1, 0),
352 .tuner_type = UNSET,
353 .tuner_addr = ADDR_UNSET,
354 },
355 [BTTV_BOARD_MIRO] = {
356 .name = "MIRO PCTV",
357 .video_inputs = 4,
358 /* .audio_inputs= 1, */
359 .svhs = 2,
360 .gpiomask = 15,
361 .muxsel = MUXSEL(2, 3, 1, 1),
362 .gpiomux = { 2, 0, 0, 0 },
363 .gpiomute = 10,
364 .tuner_type = UNSET,
365 .tuner_addr = ADDR_UNSET,
366 },
367 [BTTV_BOARD_HAUPPAUGE] = {
368 .name = "Hauppauge (bt848)",
369 .video_inputs = 4,
370 /* .audio_inputs= 1, */
371 .svhs = 2,
372 .gpiomask = 7,
373 .muxsel = MUXSEL(2, 3, 1, 1),
374 .gpiomux = { 0, 1, 2, 3 },
375 .gpiomute = 4,
376 .tuner_type = UNSET,
377 .tuner_addr = ADDR_UNSET,
378 },
379 [BTTV_BOARD_STB] = {
380 .name = "STB, Gateway P/N 6000699 (bt848)",
381 .video_inputs = 3,
382 /* .audio_inputs= 1, */
383 .svhs = 2,
384 .gpiomask = 7,
385 .muxsel = MUXSEL(2, 3, 1, 1),
386 .gpiomux = { 4, 0, 2, 3 },
387 .gpiomute = 1,
388 .no_msp34xx = 1,
389 .tuner_type = TUNER_PHILIPS_NTSC,
390 .tuner_addr = ADDR_UNSET,
391 .pll = PLL_28,
392 .has_radio = 1,
393 },
394
395 /* ---- card 0x04 ---------------------------------- */
396 [BTTV_BOARD_INTEL] = {
397 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
398 .video_inputs = 4,
399 /* .audio_inputs= 0, */
400 .svhs = 2,
401 .gpiomask = 0,
402 .muxsel = MUXSEL(2, 3, 1, 1),
403 .gpiomux = { 0 },
404 .tuner_type = TUNER_ABSENT,
405 .tuner_addr = ADDR_UNSET,
406 },
407 [BTTV_BOARD_DIAMOND] = {
408 .name = "Diamond DTV2000",
409 .video_inputs = 4,
410 /* .audio_inputs= 1, */
411 .svhs = 2,
412 .gpiomask = 3,
413 .muxsel = MUXSEL(2, 3, 1, 0),
414 .gpiomux = { 0, 1, 0, 1 },
415 .gpiomute = 3,
416 .tuner_type = UNSET,
417 .tuner_addr = ADDR_UNSET,
418 },
419 [BTTV_BOARD_AVERMEDIA] = {
420 .name = "AVerMedia TVPhone",
421 .video_inputs = 3,
422 /* .audio_inputs= 1, */
423 .svhs = 3,
424 .muxsel = MUXSEL(2, 3, 1, 1),
425 .gpiomask = 0x0f,
426 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 },
427 /* 0x04 for some cards ?? */
428 .tuner_type = UNSET,
429 .tuner_addr = ADDR_UNSET,
430 .audio_mode_gpio= avermedia_tvphone_audio,
431 .has_remote = 1,
432 },
433 [BTTV_BOARD_MATRIX_VISION] = {
434 .name = "MATRIX-Vision MV-Delta",
435 .video_inputs = 5,
436 /* .audio_inputs= 1, */
437 .svhs = 3,
438 .gpiomask = 0,
439 .muxsel = MUXSEL(2, 3, 1, 0, 0),
440 .gpiomux = { 0 },
441 .tuner_type = TUNER_ABSENT,
442 .tuner_addr = ADDR_UNSET,
443 },
444
445 /* ---- card 0x08 ---------------------------------- */
446 [BTTV_BOARD_FLYVIDEO] = {
447 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
448 .video_inputs = 4,
449 /* .audio_inputs= 1, */
450 .svhs = 2,
451 .gpiomask = 0xc00,
452 .muxsel = MUXSEL(2, 3, 1, 1),
453 .gpiomux = { 0, 0xc00, 0x800, 0x400 },
454 .gpiomute = 0xc00,
455 .pll = PLL_28,
456 .tuner_type = UNSET,
457 .tuner_addr = ADDR_UNSET,
458 },
459 [BTTV_BOARD_TURBOTV] = {
460 .name = "IMS/IXmicro TurboTV",
461 .video_inputs = 3,
462 /* .audio_inputs= 1, */
463 .svhs = 2,
464 .gpiomask = 3,
465 .muxsel = MUXSEL(2, 3, 1, 1),
466 .gpiomux = { 1, 1, 2, 3 },
467 .pll = PLL_28,
468 .tuner_type = TUNER_TEMIC_PAL,
469 .tuner_addr = ADDR_UNSET,
470 },
471 [BTTV_BOARD_HAUPPAUGE878] = {
472 .name = "Hauppauge (bt878)",
473 .video_inputs = 4,
474 /* .audio_inputs= 1, */
475 .svhs = 2,
476 .gpiomask = 0x0f, /* old: 7 */
477 .muxsel = MUXSEL(2, 0, 1, 1),
478 .gpiomux = { 0, 1, 2, 3 },
479 .gpiomute = 4,
480 .pll = PLL_28,
481 .tuner_type = UNSET,
482 .tuner_addr = ADDR_UNSET,
483 },
484 [BTTV_BOARD_MIROPRO] = {
485 .name = "MIRO PCTV pro",
486 .video_inputs = 3,
487 /* .audio_inputs= 1, */
488 .svhs = 2,
489 .gpiomask = 0x3014f,
490 .muxsel = MUXSEL(2, 3, 1, 1),
491 .gpiomux = { 0x20001,0x10001, 0, 0 },
492 .gpiomute = 10,
493 .tuner_type = UNSET,
494 .tuner_addr = ADDR_UNSET,
495 },
496
497 /* ---- card 0x0c ---------------------------------- */
498 [BTTV_BOARD_ADSTECH_TV] = {
499 .name = "ADS Technologies Channel Surfer TV (bt848)",
500 .video_inputs = 3,
501 /* .audio_inputs= 1, */
502 .svhs = 2,
503 .gpiomask = 15,
504 .muxsel = MUXSEL(2, 3, 1, 1),
505 .gpiomux = { 13, 14, 11, 7 },
506 .tuner_type = UNSET,
507 .tuner_addr = ADDR_UNSET,
508 },
509 [BTTV_BOARD_AVERMEDIA98] = {
510 .name = "AVerMedia TVCapture 98",
511 .video_inputs = 3,
512 /* .audio_inputs= 4, */
513 .svhs = 2,
514 .gpiomask = 15,
515 .muxsel = MUXSEL(2, 3, 1, 1),
516 .gpiomux = { 13, 14, 11, 7 },
517 .msp34xx_alt = 1,
518 .pll = PLL_28,
519 .tuner_type = TUNER_PHILIPS_PAL,
520 .tuner_addr = ADDR_UNSET,
521 .audio_mode_gpio= avermedia_tv_stereo_audio,
522 .no_gpioirq = 1,
523 },
524 [BTTV_BOARD_VHX] = {
525 .name = "Aimslab Video Highway Xtreme (VHX)",
526 .video_inputs = 3,
527 /* .audio_inputs= 1, */
528 .svhs = 2,
529 .gpiomask = 7,
530 .muxsel = MUXSEL(2, 3, 1, 1),
531 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */
532 .gpiomute = 4,
533 .pll = PLL_28,
534 .tuner_type = UNSET,
535 .tuner_addr = ADDR_UNSET,
536 },
537 [BTTV_BOARD_ZOLTRIX] = {
538 .name = "Zoltrix TV-Max",
539 .video_inputs = 3,
540 /* .audio_inputs= 1, */
541 .svhs = 2,
542 .gpiomask = 15,
543 .muxsel = MUXSEL(2, 3, 1, 1),
544 .gpiomux = { 0, 0, 1, 0 },
545 .gpiomute = 10,
546 .tuner_type = UNSET,
547 .tuner_addr = ADDR_UNSET,
548 },
549
550 /* ---- card 0x10 ---------------------------------- */
551 [BTTV_BOARD_PIXVIEWPLAYTV] = {
552 .name = "Prolink Pixelview PlayTV (bt878)",
553 .video_inputs = 3,
554 /* .audio_inputs= 1, */
555 .svhs = 2,
556 .gpiomask = 0x01fe00,
557 .muxsel = MUXSEL(2, 3, 1, 1),
558 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */
559 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
560 .gpiomute = 0x002000,
561 .pll = PLL_28,
562 .tuner_type = UNSET,
563 .tuner_addr = ADDR_UNSET,
564 },
565 [BTTV_BOARD_WINVIEW_601] = {
566 .name = "Leadtek WinView 601",
567 .video_inputs = 3,
568 /* .audio_inputs= 1, */
569 .svhs = 2,
570 .gpiomask = 0x8300f8,
571 .muxsel = MUXSEL(2, 3, 1, 1, 0),
572 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 },
573 .gpiomute = 0xcfa007,
574 .tuner_type = UNSET,
575 .tuner_addr = ADDR_UNSET,
576 .volume_gpio = winview_volume,
577 .has_radio = 1,
578 },
579 [BTTV_BOARD_AVEC_INTERCAP] = {
580 .name = "AVEC Intercapture",
581 .video_inputs = 3,
582 /* .audio_inputs= 2, */
583 .svhs = 2,
584 .gpiomask = 0,
585 .muxsel = MUXSEL(2, 3, 1, 1),
586 .gpiomux = { 1, 0, 0, 0 },
587 .tuner_type = UNSET,
588 .tuner_addr = ADDR_UNSET,
589 },
590 [BTTV_BOARD_LIFE_FLYKIT] = {
591 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
592 .video_inputs = 4,
593 /* .audio_inputs= 1, */
594 .svhs = NO_SVHS,
595 .gpiomask = 0x8dff00,
596 .muxsel = MUXSEL(2, 3, 1, 1),
597 .gpiomux = { 0 },
598 .no_msp34xx = 1,
599 .tuner_type = TUNER_ABSENT,
600 .tuner_addr = ADDR_UNSET,
601 },
602
603 /* ---- card 0x14 ---------------------------------- */
604 [BTTV_BOARD_CEI_RAFFLES] = {
605 .name = "CEI Raffles Card",
606 .video_inputs = 3,
607 /* .audio_inputs= 3, */
608 .svhs = 2,
609 .muxsel = MUXSEL(2, 3, 1, 1),
610 .tuner_type = UNSET,
611 .tuner_addr = ADDR_UNSET,
612 },
613 [BTTV_BOARD_CONFERENCETV] = {
614 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
615 .video_inputs = 4,
616 /* .audio_inputs= 2, tuner, line in */
617 .svhs = 2,
618 .gpiomask = 0x1800,
619 .muxsel = MUXSEL(2, 3, 1, 1),
620 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
621 .gpiomute = 0x1800,
622 .pll = PLL_28,
623 .tuner_type = TUNER_PHILIPS_PAL_I,
624 .tuner_addr = ADDR_UNSET,
625 },
626 [BTTV_BOARD_PHOEBE_TVMAS] = {
627 .name = "Askey CPH050/ Phoebe Tv Master + FM",
628 .video_inputs = 3,
629 /* .audio_inputs= 1, */
630 .svhs = 2,
631 .gpiomask = 0xc00,
632 .muxsel = MUXSEL(2, 3, 1, 1),
633 .gpiomux = { 0, 1, 0x800, 0x400 },
634 .gpiomute = 0xc00,
635 .pll = PLL_28,
636 .tuner_type = UNSET,
637 .tuner_addr = ADDR_UNSET,
638 },
639 [BTTV_BOARD_MODTEC_205] = {
640 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
641 .video_inputs = 3,
642 /* .audio_inputs= 1, */
643 .svhs = NO_SVHS,
644 .has_dig_in = 1,
645 .gpiomask = 7,
646 .muxsel = MUXSEL(2, 3, 0), /* input 2 is digital */
647 /* .digital_mode= DIGITAL_MODE_CAMERA, */
648 .gpiomux = { 0, 0, 0, 0 },
649 .no_msp34xx = 1,
650 .pll = PLL_28,
651 .tuner_type = TUNER_ALPS_TSBB5_PAL_I,
652 .tuner_addr = ADDR_UNSET,
653 },
654
655 /* ---- card 0x18 ---------------------------------- */
656 [BTTV_BOARD_MAGICTVIEW061] = {
657 .name = "Askey CPH05X/06X (bt878) [many vendors]",
658 .video_inputs = 3,
659 /* .audio_inputs= 1, */
660 .svhs = 2,
661 .gpiomask = 0xe00,
662 .muxsel = MUXSEL(2, 3, 1, 1),
663 .gpiomux = {0x400, 0x400, 0x400, 0x400 },
664 .gpiomute = 0xc00,
665 .pll = PLL_28,
666 .tuner_type = UNSET,
667 .tuner_addr = ADDR_UNSET,
668 .has_remote = 1,
669 .has_radio = 1, /* not every card has radio */
670 },
671 [BTTV_BOARD_VOBIS_BOOSTAR] = {
672 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
673 .video_inputs = 3,
674 /* .audio_inputs= 1, */
675 .svhs = 2,
676 .gpiomask = 0x1f0fff,
677 .muxsel = MUXSEL(2, 3, 1, 1),
678 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
679 .gpiomute = 0x40000,
680 .tuner_type = TUNER_PHILIPS_PAL,
681 .tuner_addr = ADDR_UNSET,
682 .audio_mode_gpio= terratv_audio,
683 },
684 [BTTV_BOARD_HAUPPAUG_WCAM] = {
685 .name = "Hauppauge WinCam newer (bt878)",
686 .video_inputs = 4,
687 /* .audio_inputs= 1, */
688 .svhs = 3,
689 .gpiomask = 7,
690 .muxsel = MUXSEL(2, 0, 1, 1),
691 .gpiomux = { 0, 1, 2, 3 },
692 .gpiomute = 4,
693 .tuner_type = UNSET,
694 .tuner_addr = ADDR_UNSET,
695 },
696 [BTTV_BOARD_MAXI] = {
697 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
698 .video_inputs = 4,
699 /* .audio_inputs= 2, */
700 .svhs = 2,
701 .gpiomask = 0x1800,
702 .muxsel = MUXSEL(2, 3, 1, 1),
703 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
704 .gpiomute = 0x1800,
705 .pll = PLL_28,
706 .tuner_type = TUNER_PHILIPS_SECAM,
707 .tuner_addr = ADDR_UNSET,
708 },
709
710 /* ---- card 0x1c ---------------------------------- */
711 [BTTV_BOARD_TERRATV] = {
712 .name = "Terratec TerraTV+ Version 1.1 (bt878)",
713 .video_inputs = 3,
714 /* .audio_inputs= 1, */
715 .svhs = 2,
716 .gpiomask = 0x1f0fff,
717 .muxsel = MUXSEL(2, 3, 1, 1),
718 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 },
719 .gpiomute = 0x40000,
720 .tuner_type = TUNER_PHILIPS_PAL,
721 .tuner_addr = ADDR_UNSET,
722 .audio_mode_gpio= terratv_audio,
723 /* GPIO wiring:
724 External 20 pin connector (for Active Radio Upgrade board)
725 gpio00: i2c-sda
726 gpio01: i2c-scl
727 gpio02: om5610-data
728 gpio03: om5610-clk
729 gpio04: om5610-wre
730 gpio05: om5610-stereo
731 gpio06: rds6588-davn
732 gpio07: Pin 7 n.c.
733 gpio08: nIOW
734 gpio09+10: nIOR, nSEL ?? (bt878)
735 gpio09: nIOR (bt848)
736 gpio10: nSEL (bt848)
737 Sound Routing:
738 gpio16: u2-A0 (1st 4052bt)
739 gpio17: u2-A1
740 gpio18: u2-nEN
741 gpio19: u4-A0 (2nd 4052)
742 gpio20: u4-A1
743 u4-nEN - GND
744 Btspy:
745 00000 : Cdrom (internal audio input)
746 10000 : ext. Video audio input
747 20000 : TV Mono
748 a0000 : TV Mono/2
749 1a0000 : TV Stereo
750 30000 : Radio
751 40000 : Mute
752 */
753
754 },
755 [BTTV_BOARD_PXC200] = {
756 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
757 .name = "Imagenation PXC200",
758 .video_inputs = 5,
759 /* .audio_inputs= 1, */
760 .svhs = 1, /* was: 4 */
761 .gpiomask = 0,
762 .muxsel = MUXSEL(2, 3, 1, 0, 0),
763 .gpiomux = { 0 },
764 .tuner_type = TUNER_ABSENT,
765 .tuner_addr = ADDR_UNSET,
766 .muxsel_hook = PXC200_muxsel,
767
768 },
769 [BTTV_BOARD_FLYVIDEO_98] = {
770 .name = "Lifeview FlyVideo 98 LR50",
771 .video_inputs = 4,
772 /* .audio_inputs= 1, */
773 .svhs = 2,
774 .gpiomask = 0x1800, /* 0x8dfe00 */
775 .muxsel = MUXSEL(2, 3, 1, 1),
776 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 },
777 .gpiomute = 0x1800,
778 .pll = PLL_28,
779 .tuner_type = UNSET,
780 .tuner_addr = ADDR_UNSET,
781 },
782 [BTTV_BOARD_IPROTV] = {
783 .name = "Formac iProTV, Formac ProTV I (bt848)",
784 .video_inputs = 4,
785 /* .audio_inputs= 1, */
786 .svhs = 3,
787 .gpiomask = 1,
788 .muxsel = MUXSEL(2, 3, 1, 1),
789 .gpiomux = { 1, 0, 0, 0 },
790 .pll = PLL_28,
791 .tuner_type = TUNER_PHILIPS_PAL,
792 .tuner_addr = ADDR_UNSET,
793 },
794
795 /* ---- card 0x20 ---------------------------------- */
796 [BTTV_BOARD_INTEL_C_S_PCI] = {
797 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
798 .video_inputs = 4,
799 /* .audio_inputs= 0, */
800 .svhs = 2,
801 .gpiomask = 0,
802 .muxsel = MUXSEL(2, 3, 1, 1),
803 .gpiomux = { 0 },
804 .tuner_type = TUNER_ABSENT,
805 .tuner_addr = ADDR_UNSET,
806 },
807 [BTTV_BOARD_TERRATVALUE] = {
808 .name = "Terratec TerraTValue Version Bt878",
809 .video_inputs = 3,
810 /* .audio_inputs= 1, */
811 .svhs = 2,
812 .gpiomask = 0xffff00,
813 .muxsel = MUXSEL(2, 3, 1, 1),
814 .gpiomux = { 0x500, 0, 0x300, 0x900 },
815 .gpiomute = 0x900,
816 .pll = PLL_28,
817 .tuner_type = TUNER_PHILIPS_PAL,
818 .tuner_addr = ADDR_UNSET,
819 },
820 [BTTV_BOARD_WINFAST2000] = {
821 .name = "Leadtek WinFast 2000/ WinFast 2000 XP",
822 .video_inputs = 4,
823 /* .audio_inputs= 1, */
824 .svhs = 2,
825 /* TV, CVid, SVid, CVid over SVid connector */
826 .muxsel = MUXSEL(2, 3, 1, 1, 0),
827 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
828 .gpiomask = 0xb33000,
829 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 },
830 .gpiomute = 0x800000,
831 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
832 gpio23 -- hef4052:nEnable (0x800000)
833 gpio12 -- hef4052:A1
834 gpio13 -- hef4052:A0
835 0x0000: external audio
836 0x1000: FM
837 0x2000: TV
838 0x3000: n.c.
839 Note: There exists another variant "Winfast 2000" with tv stereo !?
840 Note: eeprom only contains FF and pci subsystem id 107d:6606
841 */
842 .pll = PLL_28,
843 .has_radio = 1,
844 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */
845 .tuner_addr = ADDR_UNSET,
846 .audio_mode_gpio= winfast2000_audio,
847 .has_remote = 1,
848 },
849 [BTTV_BOARD_CHRONOS_VS2] = {
850 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
851 .video_inputs = 4,
852 /* .audio_inputs= 3, */
853 .svhs = 2,
854 .gpiomask = 0x1800,
855 .muxsel = MUXSEL(2, 3, 1, 1),
856 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
857 .gpiomute = 0x1800,
858 .pll = PLL_28,
859 .tuner_type = UNSET,
860 .tuner_addr = ADDR_UNSET,
861 },
862
863 /* ---- card 0x24 ---------------------------------- */
864 [BTTV_BOARD_TYPHOON_TVIEW] = {
865 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
866 .video_inputs = 4,
867 /* .audio_inputs= 3, */
868 .svhs = 2,
869 .gpiomask = 0x1800,
870 .muxsel = MUXSEL(2, 3, 1, 1),
871 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
872 .gpiomute = 0x1800,
873 .pll = PLL_28,
874 .tuner_type = UNSET,
875 .tuner_addr = ADDR_UNSET,
876 .has_radio = 1,
877 },
878 [BTTV_BOARD_PXELVWPLTVPRO] = {
879 .name = "Prolink PixelView PlayTV pro",
880 .video_inputs = 3,
881 /* .audio_inputs= 1, */
882 .svhs = 2,
883 .gpiomask = 0xff,
884 .muxsel = MUXSEL(2, 3, 1, 1),
885 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
886 .gpiomute = 0x29,
887 .no_msp34xx = 1,
888 .pll = PLL_28,
889 .tuner_type = UNSET,
890 .tuner_addr = ADDR_UNSET,
891 },
892 [BTTV_BOARD_MAGICTVIEW063] = {
893 .name = "Askey CPH06X TView99",
894 .video_inputs = 4,
895 /* .audio_inputs= 1, */
896 .svhs = 2,
897 .gpiomask = 0x551e00,
898 .muxsel = MUXSEL(2, 3, 1, 0),
899 .gpiomux = { 0x551400, 0x551200, 0, 0 },
900 .gpiomute = 0x551c00,
901 .pll = PLL_28,
902 .tuner_type = TUNER_PHILIPS_PAL_I,
903 .tuner_addr = ADDR_UNSET,
904 .has_remote = 1,
905 },
906 [BTTV_BOARD_PINNACLE] = {
907 .name = "Pinnacle PCTV Studio/Rave",
908 .video_inputs = 3,
909 /* .audio_inputs= 1, */
910 .svhs = 2,
911 .gpiomask = 0x03000F,
912 .muxsel = MUXSEL(2, 3, 1, 1),
913 .gpiomux = { 2, 0xd0001, 0, 0 },
914 .gpiomute = 1,
915 .pll = PLL_28,
916 .tuner_type = UNSET,
917 .tuner_addr = ADDR_UNSET,
918 },
919
920 /* ---- card 0x28 ---------------------------------- */
921 [BTTV_BOARD_STB2] = {
922 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
923 .video_inputs = 3,
924 /* .audio_inputs= 1, */
925 .svhs = 2,
926 .gpiomask = 7,
927 .muxsel = MUXSEL(2, 3, 1, 1),
928 .gpiomux = { 4, 0, 2, 3 },
929 .gpiomute = 1,
930 .no_msp34xx = 1,
931 .tuner_type = TUNER_PHILIPS_NTSC,
932 .tuner_addr = ADDR_UNSET,
933 .pll = PLL_28,
934 .has_radio = 1,
935 },
936 [BTTV_BOARD_AVPHONE98] = {
937 .name = "AVerMedia TVPhone 98",
938 .video_inputs = 3,
939 /* .audio_inputs= 4, */
940 .svhs = 2,
941 .gpiomask = 15,
942 .muxsel = MUXSEL(2, 3, 1, 1),
943 .gpiomux = { 13, 4, 11, 7 },
944 .pll = PLL_28,
945 .tuner_type = UNSET,
946 .tuner_addr = ADDR_UNSET,
947 .has_radio = 1,
948 .audio_mode_gpio= avermedia_tvphone_audio,
949 },
950 [BTTV_BOARD_PV951] = {
951 .name = "ProVideo PV951", /* pic16c54 */
952 .video_inputs = 3,
953 /* .audio_inputs= 1, */
954 .svhs = 2,
955 .gpiomask = 0,
956 .muxsel = MUXSEL(2, 3, 1, 1),
957 .gpiomux = { 0, 0, 0, 0},
958 .no_msp34xx = 1,
959 .pll = PLL_28,
960 .tuner_type = TUNER_PHILIPS_PAL_I,
961 .tuner_addr = ADDR_UNSET,
962 },
963 [BTTV_BOARD_ONAIR_TV] = {
964 .name = "Little OnAir TV",
965 .video_inputs = 3,
966 /* .audio_inputs= 1, */
967 .svhs = 2,
968 .gpiomask = 0xe00b,
969 .muxsel = MUXSEL(2, 3, 1, 1),
970 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 },
971 .gpiomute = 0xff3ffc,
972 .no_msp34xx = 1,
973 .tuner_type = UNSET,
974 .tuner_addr = ADDR_UNSET,
975 },
976
977 /* ---- card 0x2c ---------------------------------- */
978 [BTTV_BOARD_SIGMA_TVII_FM] = {
979 .name = "Sigma TVII-FM",
980 .video_inputs = 2,
981 /* .audio_inputs= 1, */
982 .svhs = NO_SVHS,
983 .gpiomask = 3,
984 .muxsel = MUXSEL(2, 3, 1, 1),
985 .gpiomux = { 1, 1, 0, 2 },
986 .gpiomute = 3,
987 .no_msp34xx = 1,
988 .pll = PLL_NONE,
989 .tuner_type = UNSET,
990 .tuner_addr = ADDR_UNSET,
991 },
992 [BTTV_BOARD_MATRIX_VISION2] = {
993 .name = "MATRIX-Vision MV-Delta 2",
994 .video_inputs = 5,
995 /* .audio_inputs= 1, */
996 .svhs = 3,
997 .gpiomask = 0,
998 .muxsel = MUXSEL(2, 3, 1, 0, 0),
999 .gpiomux = { 0 },
1000 .no_msp34xx = 1,
1001 .pll = PLL_28,
1002 .tuner_type = TUNER_ABSENT,
1003 .tuner_addr = ADDR_UNSET,
1004 },
1005 [BTTV_BOARD_ZOLTRIX_GENIE] = {
1006 .name = "Zoltrix Genie TV/FM",
1007 .video_inputs = 3,
1008 /* .audio_inputs= 1, */
1009 .svhs = 2,
1010 .gpiomask = 0xbcf03f,
1011 .muxsel = MUXSEL(2, 3, 1, 1),
1012 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 },
1013 .gpiomute = 0xbcb03f,
1014 .no_msp34xx = 1,
1015 .pll = PLL_28,
1016 .tuner_type = TUNER_TEMIC_4039FR5_NTSC,
1017 .tuner_addr = ADDR_UNSET,
1018 },
1019 [BTTV_BOARD_TERRATVRADIO] = {
1020 .name = "Terratec TV/Radio+",
1021 .video_inputs = 3,
1022 /* .audio_inputs= 1, */
1023 .svhs = 2,
1024 .gpiomask = 0x70000,
1025 .muxsel = MUXSEL(2, 3, 1, 1),
1026 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
1027 .gpiomute = 0x40000,
1028 .no_msp34xx = 1,
1029 .pll = PLL_35,
1030 .tuner_type = TUNER_PHILIPS_PAL_I,
1031 .tuner_addr = ADDR_UNSET,
1032 .has_radio = 1,
1033 },
1034
1035 /* ---- card 0x30 ---------------------------------- */
1036 [BTTV_BOARD_DYNALINK] = {
1037 .name = "Askey CPH03x/ Dynalink Magic TView",
1038 .video_inputs = 3,
1039 /* .audio_inputs= 1, */
1040 .svhs = 2,
1041 .gpiomask = 15,
1042 .muxsel = MUXSEL(2, 3, 1, 1),
1043 .gpiomux = {2,0,0,0 },
1044 .gpiomute = 1,
1045 .pll = PLL_28,
1046 .tuner_type = UNSET,
1047 .tuner_addr = ADDR_UNSET,
1048 },
1049 [BTTV_BOARD_GVBCTV3PCI] = {
1050 .name = "IODATA GV-BCTV3/PCI",
1051 .video_inputs = 3,
1052 /* .audio_inputs= 1, */
1053 .svhs = 2,
1054 .gpiomask = 0x010f00,
1055 .muxsel = MUXSEL(2, 3, 0, 0),
1056 .gpiomux = {0x10000, 0, 0x10000, 0 },
1057 .no_msp34xx = 1,
1058 .pll = PLL_28,
1059 .tuner_type = TUNER_ALPS_TSHC6_NTSC,
1060 .tuner_addr = ADDR_UNSET,
1061 .audio_mode_gpio= gvbctv3pci_audio,
1062 },
1063 [BTTV_BOARD_PXELVWPLTVPAK] = {
1064 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
1065 .video_inputs = 5,
1066 /* .audio_inputs= 1, */
1067 .svhs = 3,
1068 .has_dig_in = 1,
1069 .gpiomask = 0xAA0000,
1070 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
1071 /* .digital_mode= DIGITAL_MODE_CAMERA, */
1072 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 },
1073 .gpiomute = 0xa8000,
1074 .no_msp34xx = 1,
1075 .pll = PLL_28,
1076 .tuner_type = TUNER_PHILIPS_PAL_I,
1077 .tuner_addr = ADDR_UNSET,
1078 .has_remote = 1,
1079 /* GPIO wiring: (different from Rev.4C !)
1080 GPIO17: U4.A0 (first hef4052bt)
1081 GPIO19: U4.A1
1082 GPIO20: U5.A1 (second hef4052bt)
1083 GPIO21: U4.nEN
1084 GPIO22: BT832 Reset Line
1085 GPIO23: A5,A0, U5,nEN
1086 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
1087 */
1088 },
1089 [BTTV_BOARD_EAGLE] = {
1090 .name = "Eagle Wireless Capricorn2 (bt878A)",
1091 .video_inputs = 4,
1092 /* .audio_inputs= 1, */
1093 .svhs = 2,
1094 .gpiomask = 7,
1095 .muxsel = MUXSEL(2, 0, 1, 1),
1096 .gpiomux = { 0, 1, 2, 3 },
1097 .gpiomute = 4,
1098 .pll = PLL_28,
1099 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */,
1100 .tuner_addr = ADDR_UNSET,
1101 },
1102
1103 /* ---- card 0x34 ---------------------------------- */
1104 [BTTV_BOARD_PINNACLEPRO] = {
1105 /* David Härdeman <david@2gen.com> */
1106 .name = "Pinnacle PCTV Studio Pro",
1107 .video_inputs = 4,
1108 /* .audio_inputs= 1, */
1109 .svhs = 3,
1110 .gpiomask = 0x03000F,
1111 .muxsel = MUXSEL(2, 3, 1, 1),
1112 .gpiomux = { 1, 0xd0001, 0, 0 },
1113 .gpiomute = 10,
1114 /* sound path (5 sources):
1115 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
1116 0= ext. Audio IN
1117 1= from MUX2
1118 2= Mono TV sound from Tuner
1119 3= not connected
1120 MUX2 (mask 0x30000):
1121 0,2,3= from MSP34xx
1122 1= FM stereo Radio from Tuner */
1123 .pll = PLL_28,
1124 .tuner_type = UNSET,
1125 .tuner_addr = ADDR_UNSET,
1126 },
1127 [BTTV_BOARD_TVIEW_RDS_FM] = {
1128 /* Claas Langbehn <claas@bigfoot.com>,
1129 Sven Grothklags <sven@upb.de> */
1130 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
1131 .video_inputs = 4,
1132 /* .audio_inputs= 3, */
1133 .svhs = 2,
1134 .gpiomask = 0x1c,
1135 .muxsel = MUXSEL(2, 3, 1, 1),
1136 .gpiomux = { 0, 0, 0x10, 8 },
1137 .gpiomute = 4,
1138 .pll = PLL_28,
1139 .tuner_type = TUNER_PHILIPS_PAL,
1140 .tuner_addr = ADDR_UNSET,
1141 .has_radio = 1,
1142 },
1143 [BTTV_BOARD_LIFETEC_9415] = {
1144 /* Tim Röstermundt <rosterm@uni-muenster.de>
1145 in de.comp.os.unix.linux.hardware:
1146 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
1147 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
1148 options tuner type=5 */
1149 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
1150 .video_inputs = 4,
1151 /* .audio_inputs= 1, */
1152 .svhs = 2,
1153 .gpiomask = 0x18e0,
1154 .muxsel = MUXSEL(2, 3, 1, 1),
1155 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1156 .gpiomute = 0x18e0,
1157 /* For cards with tda9820/tda9821:
1158 0x0000: Tuner normal stereo
1159 0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
1160 0x0880: Tuner A2 stereo */
1161 .pll = PLL_28,
1162 .tuner_type = UNSET,
1163 .tuner_addr = ADDR_UNSET,
1164 },
1165 [BTTV_BOARD_BESTBUY_EASYTV] = {
1166 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1167 old Easy TV BT848 version (model CPH031) */
1168 .name = "Askey CPH031/ BESTBUY Easy TV",
1169 .video_inputs = 4,
1170 /* .audio_inputs= 1, */
1171 .svhs = 2,
1172 .gpiomask = 0xF,
1173 .muxsel = MUXSEL(2, 3, 1, 0),
1174 .gpiomux = { 2, 0, 0, 0 },
1175 .gpiomute = 10,
1176 .pll = PLL_28,
1177 .tuner_type = TUNER_TEMIC_PAL,
1178 .tuner_addr = ADDR_UNSET,
1179 },
1180
1181 /* ---- card 0x38 ---------------------------------- */
1182 [BTTV_BOARD_FLYVIDEO_98FM] = {
1183 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */
1184 .name = "Lifeview FlyVideo 98FM LR50",
1185 .video_inputs = 4,
1186 /* .audio_inputs= 3, */
1187 .svhs = 2,
1188 .gpiomask = 0x1800,
1189 .muxsel = MUXSEL(2, 3, 1, 1),
1190 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
1191 .gpiomute = 0x1800,
1192 .pll = PLL_28,
1193 .tuner_type = TUNER_PHILIPS_PAL,
1194 .tuner_addr = ADDR_UNSET,
1195 },
1196 /* This is the ultimate cheapo capture card
1197 * just a BT848A on a small PCB!
1198 * Steve Hosgood <steve@equiinet.com> */
1199 [BTTV_BOARD_GRANDTEC] = {
1200 .name = "GrandTec 'Grand Video Capture' (Bt848)",
1201 .video_inputs = 2,
1202 /* .audio_inputs= 0, */
1203 .svhs = 1,
1204 .gpiomask = 0,
1205 .muxsel = MUXSEL(3, 1),
1206 .gpiomux = { 0 },
1207 .no_msp34xx = 1,
1208 .pll = PLL_35,
1209 .tuner_type = TUNER_ABSENT,
1210 .tuner_addr = ADDR_UNSET,
1211 },
1212 [BTTV_BOARD_ASKEY_CPH060] = {
1213 /* Daniel Herrington <daniel.herrington@home.com> */
1214 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)",
1215 .video_inputs = 3,
1216 /* .audio_inputs= 1, */
1217 .svhs = 2,
1218 .gpiomask = 0xe00,
1219 .muxsel = MUXSEL(2, 3, 1, 1),
1220 .gpiomux = { 0x400, 0x400, 0x400, 0x400 },
1221 .gpiomute = 0x800,
1222 .pll = PLL_28,
1223 .tuner_type = TUNER_TEMIC_4036FY5_NTSC,
1224 .tuner_addr = ADDR_UNSET,
1225 },
1226 [BTTV_BOARD_ASKEY_CPH03X] = {
1227 /* Matti Mottus <mottus@physic.ut.ee> */
1228 .name = "Askey CPH03x TV Capturer",
1229 .video_inputs = 4,
1230 /* .audio_inputs= 1, */
1231 .svhs = 2,
1232 .gpiomask = 0x03000F,
1233 .muxsel = MUXSEL(2, 3, 1, 0),
1234 .gpiomux = { 2, 0, 0, 0 },
1235 .gpiomute = 1,
1236 .pll = PLL_28,
1237 .tuner_type = TUNER_TEMIC_PAL,
1238 .tuner_addr = ADDR_UNSET,
1239 .has_remote = 1,
1240 },
1241
1242 /* ---- card 0x3c ---------------------------------- */
1243 [BTTV_BOARD_MM100PCTV] = {
1244 /* Philip Blundell <philb@gnu.org> */
1245 .name = "Modular Technology MM100PCTV",
1246 .video_inputs = 2,
1247 /* .audio_inputs= 2, */
1248 .svhs = NO_SVHS,
1249 .gpiomask = 11,
1250 .muxsel = MUXSEL(2, 3, 1, 1),
1251 .gpiomux = { 2, 0, 0, 1 },
1252 .gpiomute = 8,
1253 .pll = PLL_35,
1254 .tuner_type = TUNER_TEMIC_PAL,
1255 .tuner_addr = ADDR_UNSET,
1256 },
1257 [BTTV_BOARD_GMV1] = {
1258 /* Adrian Cox <adrian@humboldt.co.uk */
1259 .name = "AG Electronics GMV1",
1260 .video_inputs = 2,
1261 /* .audio_inputs= 0, */
1262 .svhs = 1,
1263 .gpiomask = 0xF,
1264 .muxsel = MUXSEL(2, 2),
1265 .gpiomux = { },
1266 .no_msp34xx = 1,
1267 .pll = PLL_28,
1268 .tuner_type = TUNER_ABSENT,
1269 .tuner_addr = ADDR_UNSET,
1270 },
1271 [BTTV_BOARD_BESTBUY_EASYTV2] = {
1272 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1273 new Easy TV BT878 version (model CPH061)
1274 special thanks to Informatica Mieres for providing the card */
1275 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)",
1276 .video_inputs = 3,
1277 /* .audio_inputs= 2, */
1278 .svhs = 2,
1279 .gpiomask = 0xFF,
1280 .muxsel = MUXSEL(2, 3, 1, 0),
1281 .gpiomux = { 1, 0, 4, 4 },
1282 .gpiomute = 9,
1283 .pll = PLL_28,
1284 .tuner_type = TUNER_PHILIPS_PAL,
1285 .tuner_addr = ADDR_UNSET,
1286 },
1287 [BTTV_BOARD_ATI_TVWONDER] = {
1288 /* Lukas Gebauer <geby@volny.cz> */
1289 .name = "ATI TV-Wonder",
1290 .video_inputs = 3,
1291 /* .audio_inputs= 1, */
1292 .svhs = 2,
1293 .gpiomask = 0xf03f,
1294 .muxsel = MUXSEL(2, 3, 1, 0),
1295 .gpiomux = { 0xbffe, 0, 0xbfff, 0 },
1296 .gpiomute = 0xbffe,
1297 .pll = PLL_28,
1298 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1299 .tuner_addr = ADDR_UNSET,
1300 },
1301
1302 /* ---- card 0x40 ---------------------------------- */
1303 [BTTV_BOARD_ATI_TVWONDERVE] = {
1304 /* Lukas Gebauer <geby@volny.cz> */
1305 .name = "ATI TV-Wonder VE",
1306 .video_inputs = 2,
1307 /* .audio_inputs= 1, */
1308 .svhs = NO_SVHS,
1309 .gpiomask = 1,
1310 .muxsel = MUXSEL(2, 3, 0, 1),
1311 .gpiomux = { 0, 0, 1, 0 },
1312 .no_msp34xx = 1,
1313 .pll = PLL_28,
1314 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1315 .tuner_addr = ADDR_UNSET,
1316 },
1317 [BTTV_BOARD_FLYVIDEO2000] = {
1318 /* DeeJay <deejay@westel900.net (2000S) */
1319 .name = "Lifeview FlyVideo 2000S LR90",
1320 .video_inputs = 3,
1321 /* .audio_inputs= 3, */
1322 .svhs = 2,
1323 .gpiomask = 0x18e0,
1324 .muxsel = MUXSEL(2, 3, 0, 1),
1325 /* Radio changed from 1e80 to 0x800 to make
1326 FlyVideo2000S in .hu happy (gm)*/
1327 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */
1328 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1329 .gpiomute = 0x1800,
1330 .audio_mode_gpio= fv2000s_audio,
1331 .no_msp34xx = 1,
1332 .pll = PLL_28,
1333 .tuner_type = TUNER_PHILIPS_PAL,
1334 .tuner_addr = ADDR_UNSET,
1335 },
1336 [BTTV_BOARD_TERRATVALUER] = {
1337 .name = "Terratec TValueRadio",
1338 .video_inputs = 3,
1339 /* .audio_inputs= 1, */
1340 .svhs = 2,
1341 .gpiomask = 0xffff00,
1342 .muxsel = MUXSEL(2, 3, 1, 1),
1343 .gpiomux = { 0x500, 0x500, 0x300, 0x900 },
1344 .gpiomute = 0x900,
1345 .pll = PLL_28,
1346 .tuner_type = TUNER_PHILIPS_PAL,
1347 .tuner_addr = ADDR_UNSET,
1348 .has_radio = 1,
1349 },
1350 [BTTV_BOARD_GVBCTV4PCI] = {
1351 /* TANAKA Kei <peg00625@nifty.com> */
1352 .name = "IODATA GV-BCTV4/PCI",
1353 .video_inputs = 3,
1354 /* .audio_inputs= 1, */
1355 .svhs = 2,
1356 .gpiomask = 0x010f00,
1357 .muxsel = MUXSEL(2, 3, 0, 0),
1358 .gpiomux = {0x10000, 0, 0x10000, 0 },
1359 .no_msp34xx = 1,
1360 .pll = PLL_28,
1361 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC,
1362 .tuner_addr = ADDR_UNSET,
1363 .audio_mode_gpio= gvbctv3pci_audio,
1364 },
1365
1366 /* ---- card 0x44 ---------------------------------- */
1367 [BTTV_BOARD_VOODOOTV_FM] = {
1368 .name = "3Dfx VoodooTV FM (Euro)",
1369 /* try "insmod msp3400 simple=0" if you have
1370 * sound problems with this card. */
1371 .video_inputs = 4,
1372 /* .audio_inputs= 1, */
1373 .svhs = NO_SVHS,
1374 .gpiomask = 0x4f8a00,
1375 /* 0x100000: 1=MSP enabled (0=disable again)
1376 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1377 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1378 .gpiomute = 0x947fff,
1379 /* tvtuner, radio, external,internal, mute, stereo
1380 * tuner, Composite, SVid, Composite-on-Svid-adapter */
1381 .muxsel = MUXSEL(2, 3, 0, 1),
1382 .tuner_type = TUNER_MT2032,
1383 .tuner_addr = ADDR_UNSET,
1384 .pll = PLL_28,
1385 .has_radio = 1,
1386 },
1387 [BTTV_BOARD_VOODOOTV_200] = {
1388 .name = "VoodooTV 200 (USA)",
1389 /* try "insmod msp3400 simple=0" if you have
1390 * sound problems with this card. */
1391 .video_inputs = 4,
1392 /* .audio_inputs= 1, */
1393 .svhs = NO_SVHS,
1394 .gpiomask = 0x4f8a00,
1395 /* 0x100000: 1=MSP enabled (0=disable again)
1396 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1397 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1398 .gpiomute = 0x947fff,
1399 /* tvtuner, radio, external,internal, mute, stereo
1400 * tuner, Composite, SVid, Composite-on-Svid-adapter */
1401 .muxsel = MUXSEL(2, 3, 0, 1),
1402 .tuner_type = TUNER_MT2032,
1403 .tuner_addr = ADDR_UNSET,
1404 .pll = PLL_28,
1405 .has_radio = 1,
1406 },
1407 [BTTV_BOARD_AIMMS] = {
1408 /* Philip Blundell <pb@nexus.co.uk> */
1409 .name = "Active Imaging AIMMS",
1410 .video_inputs = 1,
1411 /* .audio_inputs= 0, */
1412 .tuner_type = TUNER_ABSENT,
1413 .tuner_addr = ADDR_UNSET,
1414 .pll = PLL_28,
1415 .muxsel = MUXSEL(2),
1416 .gpiomask = 0
1417 },
1418 [BTTV_BOARD_PV_BT878P_PLUS] = {
1419 /* Tomasz Pyra <hellfire@sedez.iq.pl> */
1420 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
1421 .video_inputs = 3,
1422 /* .audio_inputs= 4, */
1423 .svhs = 2,
1424 .gpiomask = 15,
1425 .muxsel = MUXSEL(2, 3, 1, 1),
1426 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */
1427 .gpiomute = 13,
1428 .pll = PLL_28,
1429 .tuner_type = TUNER_LG_PAL_I_FM,
1430 .tuner_addr = ADDR_UNSET,
1431 .has_remote = 1,
1432 /* GPIO wiring:
1433 GPIO0: U4.A0 (hef4052bt)
1434 GPIO1: U4.A1
1435 GPIO2: U4.A1 (second hef4052bt)
1436 GPIO3: U4.nEN, U5.A0, A5.nEN
1437 GPIO8-15: vrd866b ?
1438 */
1439 },
1440 [BTTV_BOARD_FLYVIDEO98EZ] = {
1441 .name = "Lifeview FlyVideo 98EZ (capture only) LR51",
1442 .video_inputs = 4,
1443 /* .audio_inputs= 0, */
1444 .svhs = 2,
1445 /* AV1, AV2, SVHS, CVid adapter on SVHS */
1446 .muxsel = MUXSEL(2, 3, 1, 1),
1447 .pll = PLL_28,
1448 .no_msp34xx = 1,
1449 .tuner_type = TUNER_ABSENT,
1450 .tuner_addr = ADDR_UNSET,
1451 },
1452
1453 /* ---- card 0x48 ---------------------------------- */
1454 [BTTV_BOARD_PV_BT878P_9B] = {
1455 /* Dariusz Kowalewski <darekk@automex.pl> */
1456 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
1457 .video_inputs = 4,
1458 /* .audio_inputs= 1, */
1459 .svhs = 2,
1460 .gpiomask = 0x3f,
1461 .muxsel = MUXSEL(2, 3, 1, 1),
1462 .gpiomux = { 0x01, 0x00, 0x03, 0x03 },
1463 .gpiomute = 0x09,
1464 .no_msp34xx = 1,
1465 .pll = PLL_28,
1466 .tuner_type = TUNER_PHILIPS_PAL,
1467 .tuner_addr = ADDR_UNSET,
1468 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */
1469 .has_radio = 1, /* Note: not all cards have radio */
1470 .has_remote = 1,
1471 /* GPIO wiring:
1472 GPIO0: A0 hef4052
1473 GPIO1: A1 hef4052
1474 GPIO3: nEN hef4052
1475 GPIO8-15: vrd866b
1476 GPIO20,22,23: R30,R29,R28
1477 */
1478 },
1479 [BTTV_BOARD_SENSORAY311_611] = {
1480 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */
1481 /* you must jumper JP5 for the 311 card (PC/104+) to work */
1482 .name = "Sensoray 311/611",
1483 .video_inputs = 5,
1484 /* .audio_inputs= 0, */
1485 .svhs = 4,
1486 .gpiomask = 0,
1487 .muxsel = MUXSEL(2, 3, 1, 0, 0),
1488 .gpiomux = { 0 },
1489 .tuner_type = TUNER_ABSENT,
1490 .tuner_addr = ADDR_UNSET,
1491 },
1492 [BTTV_BOARD_RV605] = {
1493 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */
1494 .name = "RemoteVision MX (RV605)",
1495 .video_inputs = 16,
1496 /* .audio_inputs= 0, */
1497 .svhs = NO_SVHS,
1498 .gpiomask = 0x00,
1499 .gpiomask2 = 0x07ff,
1500 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
1501 .no_msp34xx = 1,
1502 .tuner_type = TUNER_ABSENT,
1503 .tuner_addr = ADDR_UNSET,
1504 .muxsel_hook = rv605_muxsel,
1505 },
1506 [BTTV_BOARD_POWERCLR_MTV878] = {
1507 .name = "Powercolor MTV878/ MTV878R/ MTV878F",
1508 .video_inputs = 3,
1509 /* .audio_inputs= 2, */
1510 .svhs = 2,
1511 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */
1512 .muxsel = MUXSEL(2, 1, 1),
1513 .gpiomux = { 0, 1, 2, 2 },
1514 .gpiomute = 4,
1515 .tuner_type = TUNER_PHILIPS_PAL,
1516 .tuner_addr = ADDR_UNSET,
1517 .pll = PLL_28,
1518 .has_radio = 1,
1519 },
1520
1521 /* ---- card 0x4c ---------------------------------- */
1522 [BTTV_BOARD_WINDVR] = {
1523 /* Masaki Suzuki <masaki@btree.org> */
1524 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
1525 .video_inputs = 3,
1526 /* .audio_inputs= 1, */
1527 .svhs = 2,
1528 .gpiomask = 0x140007,
1529 .muxsel = MUXSEL(2, 3, 1, 1),
1530 .gpiomux = { 0, 1, 2, 3 },
1531 .gpiomute = 4,
1532 .tuner_type = TUNER_PHILIPS_NTSC,
1533 .tuner_addr = ADDR_UNSET,
1534 .audio_mode_gpio= windvr_audio,
1535 },
1536 [BTTV_BOARD_GRANDTEC_MULTI] = {
1537 .name = "GrandTec Multi Capture Card (Bt878)",
1538 .video_inputs = 4,
1539 /* .audio_inputs= 0, */
1540 .svhs = NO_SVHS,
1541 .gpiomask = 0,
1542 .muxsel = MUXSEL(2, 3, 1, 0),
1543 .gpiomux = { 0 },
1544 .no_msp34xx = 1,
1545 .pll = PLL_28,
1546 .tuner_type = TUNER_ABSENT,
1547 .tuner_addr = ADDR_UNSET,
1548 },
1549 [BTTV_BOARD_KWORLD] = {
1550 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
1551 .video_inputs = 4,
1552 /* .audio_inputs= 3, */
1553 .svhs = 2,
1554 .gpiomask = 7,
1555 /* Tuner, SVid, SVHS, SVid to SVHS connector */
1556 .muxsel = MUXSEL(2, 3, 1, 1),
1557 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio!
1558 * This card lacks external Audio In, so we mute it on Ext. & Int.
1559 * The PCB can take a sbx1637/sbx1673, wiring unknown.
1560 * This card lacks PCI subsystem ID, sigh.
1561 * gpiomux =1: lower volume, 2+3: mute
1562 * btwincap uses 0x80000/0x80003
1563 */
1564 .gpiomute = 4,
1565 .no_msp34xx = 1,
1566 .pll = PLL_28,
1567 .tuner_type = TUNER_PHILIPS_PAL,
1568 .tuner_addr = ADDR_UNSET,
1569 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
1570 radio signal strength indicators work fine. */
1571 .has_radio = 1,
1572 /* GPIO Info:
1573 GPIO0,1: HEF4052 A0,A1
1574 GPIO2: HEF4052 nENABLE
1575 GPIO3-7: n.c.
1576 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
1577 GPIO14,15: ??
1578 GPIO16-21: n.c.
1579 GPIO22,23: ??
1580 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
1581 },
1582 [BTTV_BOARD_DSP_TCVIDEO] = {
1583 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
1584 .name = "DSP Design TCVIDEO",
1585 .video_inputs = 4,
1586 .svhs = NO_SVHS,
1587 .muxsel = MUXSEL(2, 3, 1, 0),
1588 .pll = PLL_28,
1589 .tuner_type = UNSET,
1590 .tuner_addr = ADDR_UNSET,
1591 },
1592
1593 /* ---- card 0x50 ---------------------------------- */
1594 [BTTV_BOARD_HAUPPAUGEPVR] = {
1595 .name = "Hauppauge WinTV PVR",
1596 .video_inputs = 4,
1597 /* .audio_inputs= 1, */
1598 .svhs = 2,
1599 .muxsel = MUXSEL(2, 0, 1, 1),
1600 .pll = PLL_28,
1601 .tuner_type = UNSET,
1602 .tuner_addr = ADDR_UNSET,
1603
1604 .gpiomask = 7,
1605 .gpiomux = {7},
1606 },
1607 [BTTV_BOARD_GVBCTV5PCI] = {
1608 .name = "IODATA GV-BCTV5/PCI",
1609 .video_inputs = 3,
1610 /* .audio_inputs= 1, */
1611 .svhs = 2,
1612 .gpiomask = 0x0f0f80,
1613 .muxsel = MUXSEL(2, 3, 1, 0),
1614 .gpiomux = {0x030000, 0x010000, 0, 0 },
1615 .gpiomute = 0x020000,
1616 .no_msp34xx = 1,
1617 .pll = PLL_28,
1618 .tuner_type = TUNER_PHILIPS_NTSC_M,
1619 .tuner_addr = ADDR_UNSET,
1620 .audio_mode_gpio= gvbctv5pci_audio,
1621 .has_radio = 1,
1622 },
1623 [BTTV_BOARD_OSPREY1x0] = {
1624 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
1625 .video_inputs = 4, /* id-inputs-clock */
1626 /* .audio_inputs= 0, */
1627 .svhs = 3,
1628 .muxsel = MUXSEL(3, 2, 0, 1),
1629 .pll = PLL_28,
1630 .tuner_type = TUNER_ABSENT,
1631 .tuner_addr = ADDR_UNSET,
1632 .no_msp34xx = 1,
1633 .no_tda7432 = 1,
1634 },
1635 [BTTV_BOARD_OSPREY1x0_848] = {
1636 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
1637 .video_inputs = 3,
1638 /* .audio_inputs= 0, */
1639 .svhs = 2,
1640 .muxsel = MUXSEL(2, 3, 1),
1641 .pll = PLL_28,
1642 .tuner_type = TUNER_ABSENT,
1643 .tuner_addr = ADDR_UNSET,
1644 .no_msp34xx = 1,
1645 .no_tda7432 = 1,
1646 },
1647
1648 /* ---- card 0x54 ---------------------------------- */
1649 [BTTV_BOARD_OSPREY101_848] = {
1650 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */
1651 .video_inputs = 2,
1652 /* .audio_inputs= 0, */
1653 .svhs = 1,
1654 .muxsel = MUXSEL(3, 1),
1655 .pll = PLL_28,
1656 .tuner_type = TUNER_ABSENT,
1657 .tuner_addr = ADDR_UNSET,
1658 .no_msp34xx = 1,
1659 .no_tda7432 = 1,
1660 },
1661 [BTTV_BOARD_OSPREY1x1] = {
1662 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */
1663 .video_inputs = 1,
1664 /* .audio_inputs= 0, */
1665 .svhs = NO_SVHS,
1666 .muxsel = MUXSEL(0),
1667 .pll = PLL_28,
1668 .tuner_type = TUNER_ABSENT,
1669 .tuner_addr = ADDR_UNSET,
1670 .no_msp34xx = 1,
1671 .no_tda7432 = 1,
1672 },
1673 [BTTV_BOARD_OSPREY1x1_SVID] = {
1674 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */
1675 .video_inputs = 2,
1676 /* .audio_inputs= 0, */
1677 .svhs = 1,
1678 .muxsel = MUXSEL(0, 1),
1679 .pll = PLL_28,
1680 .tuner_type = TUNER_ABSENT,
1681 .tuner_addr = ADDR_UNSET,
1682 .no_msp34xx = 1,
1683 .no_tda7432 = 1,
1684 },
1685 [BTTV_BOARD_OSPREY2xx] = {
1686 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */
1687 .video_inputs = 1,
1688 /* .audio_inputs= 1, */
1689 .svhs = NO_SVHS,
1690 .muxsel = MUXSEL(0),
1691 .pll = PLL_28,
1692 .tuner_type = TUNER_ABSENT,
1693 .tuner_addr = ADDR_UNSET,
1694 .no_msp34xx = 1,
1695 .no_tda7432 = 1,
1696 },
1697
1698 /* ---- card 0x58 ---------------------------------- */
1699 [BTTV_BOARD_OSPREY2x0_SVID] = {
1700 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */
1701 .video_inputs = 2,
1702 /* .audio_inputs= 1, */
1703 .svhs = 1,
1704 .muxsel = MUXSEL(0, 1),
1705 .pll = PLL_28,
1706 .tuner_type = TUNER_ABSENT,
1707 .tuner_addr = ADDR_UNSET,
1708 .no_msp34xx = 1,
1709 .no_tda7432 = 1,
1710 },
1711 [BTTV_BOARD_OSPREY2x0] = {
1712 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */
1713 .video_inputs = 2,
1714 /* .audio_inputs= 1, */
1715 .svhs = 1,
1716 .muxsel = MUXSEL(2, 3),
1717 .pll = PLL_28,
1718 .tuner_type = TUNER_ABSENT,
1719 .tuner_addr = ADDR_UNSET,
1720 .no_msp34xx = 1,
1721 .no_tda7432 = 1,
1722 },
1723 [BTTV_BOARD_OSPREY500] = {
1724 .name = "Osprey 500", /* 500 */
1725 .video_inputs = 2,
1726 /* .audio_inputs= 1, */
1727 .svhs = 1,
1728 .muxsel = MUXSEL(2, 3),
1729 .pll = PLL_28,
1730 .tuner_type = TUNER_ABSENT,
1731 .tuner_addr = ADDR_UNSET,
1732 .no_msp34xx = 1,
1733 .no_tda7432 = 1,
1734 },
1735 [BTTV_BOARD_OSPREY540] = {
1736 .name = "Osprey 540", /* 540 */
1737 .video_inputs = 4,
1738 /* .audio_inputs= 1, */
1739 .pll = PLL_28,
1740 .tuner_type = TUNER_ABSENT,
1741 .tuner_addr = ADDR_UNSET,
1742 .no_msp34xx = 1,
1743 .no_tda7432 = 1,
1744 },
1745
1746 /* ---- card 0x5C ---------------------------------- */
1747 [BTTV_BOARD_OSPREY2000] = {
1748 .name = "Osprey 2000", /* 2000 */
1749 .video_inputs = 2,
1750 /* .audio_inputs= 1, */
1751 .svhs = 1,
1752 .muxsel = MUXSEL(2, 3),
1753 .pll = PLL_28,
1754 .tuner_type = TUNER_ABSENT,
1755 .tuner_addr = ADDR_UNSET,
1756 .no_msp34xx = 1,
1757 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */
1758 },
1759 [BTTV_BOARD_IDS_EAGLE] = {
1760 /* M G Berberich <berberic@forwiss.uni-passau.de> */
1761 .name = "IDS Eagle",
1762 .video_inputs = 4,
1763 /* .audio_inputs= 0, */
1764 .tuner_type = TUNER_ABSENT,
1765 .tuner_addr = ADDR_UNSET,
1766 .svhs = NO_SVHS,
1767 .gpiomask = 0,
1768 .muxsel = MUXSEL(2, 2, 2, 2),
1769 .muxsel_hook = eagle_muxsel,
1770 .no_msp34xx = 1,
1771 .pll = PLL_28,
1772 },
1773 [BTTV_BOARD_PINNACLESAT] = {
1774 .name = "Pinnacle PCTV Sat",
1775 .video_inputs = 2,
1776 /* .audio_inputs= 0, */
1777 .svhs = 1,
1778 .tuner_type = TUNER_ABSENT,
1779 .tuner_addr = ADDR_UNSET,
1780 .no_msp34xx = 1,
1781 .no_tda7432 = 1,
1782 .muxsel = MUXSEL(3, 1),
1783 .pll = PLL_28,
1784 .no_gpioirq = 1,
1785 .has_dvb = 1,
1786 },
1787 [BTTV_BOARD_FORMAC_PROTV] = {
1788 .name = "Formac ProTV II (bt878)",
1789 .video_inputs = 4,
1790 /* .audio_inputs= 1, */
1791 .svhs = 3,
1792 .gpiomask = 2,
1793 /* TV, Comp1, Composite over SVID con, SVID */
1794 .muxsel = MUXSEL(2, 3, 1, 1),
1795 .gpiomux = { 2, 2, 0, 0 },
1796 .pll = PLL_28,
1797 .has_radio = 1,
1798 .tuner_type = TUNER_PHILIPS_PAL,
1799 .tuner_addr = ADDR_UNSET,
1800 /* sound routing:
1801 GPIO=0x00,0x01,0x03: mute (?)
1802 0x02: both TV and radio (tuner: FM1216/I)
1803 The card has onboard audio connectors labeled "cdrom" and "board",
1804 not soldered here, though unknown wiring.
1805 Card lacks: external audio in, pci subsystem id.
1806 */
1807 },
1808
1809 /* ---- card 0x60 ---------------------------------- */
1810 [BTTV_BOARD_MACHTV] = {
1811 .name = "MachTV",
1812 .video_inputs = 3,
1813 /* .audio_inputs= 1, */
1814 .svhs = NO_SVHS,
1815 .gpiomask = 7,
1816 .muxsel = MUXSEL(2, 3, 1, 1),
1817 .gpiomux = { 0, 1, 2, 3},
1818 .gpiomute = 4,
1819 .tuner_type = TUNER_PHILIPS_PAL,
1820 .tuner_addr = ADDR_UNSET,
1821 .pll = PLL_28,
1822 },
1823 [BTTV_BOARD_EURESYS_PICOLO] = {
1824 .name = "Euresys Picolo",
1825 .video_inputs = 3,
1826 /* .audio_inputs= 0, */
1827 .svhs = 2,
1828 .gpiomask = 0,
1829 .no_msp34xx = 1,
1830 .no_tda7432 = 1,
1831 .muxsel = MUXSEL(2, 0, 1),
1832 .pll = PLL_28,
1833 .tuner_type = TUNER_ABSENT,
1834 .tuner_addr = ADDR_UNSET,
1835 },
1836 [BTTV_BOARD_PV150] = {
1837 /* Luc Van Hoeylandt <luc@e-magic.be> */
1838 .name = "ProVideo PV150", /* 0x4f */
1839 .video_inputs = 2,
1840 /* .audio_inputs= 0, */
1841 .svhs = NO_SVHS,
1842 .gpiomask = 0,
1843 .muxsel = MUXSEL(2, 3),
1844 .gpiomux = { 0 },
1845 .no_msp34xx = 1,
1846 .pll = PLL_28,
1847 .tuner_type = TUNER_ABSENT,
1848 .tuner_addr = ADDR_UNSET,
1849 },
1850 [BTTV_BOARD_AD_TVK503] = {
1851 /* Hiroshi Takekawa <sian@big.or.jp> */
1852 /* This card lacks subsystem ID */
1853 .name = "AD-TVK503", /* 0x63 */
1854 .video_inputs = 4,
1855 /* .audio_inputs= 1, */
1856 .svhs = 2,
1857 .gpiomask = 0x001e8007,
1858 .muxsel = MUXSEL(2, 3, 1, 0),
1859 /* Tuner, Radio, external, internal, off, on */
1860 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 },
1861 .gpiomute = 0x0f,
1862 .no_msp34xx = 1,
1863 .pll = PLL_28,
1864 .tuner_type = TUNER_PHILIPS_NTSC,
1865 .tuner_addr = ADDR_UNSET,
1866 .audio_mode_gpio= adtvk503_audio,
1867 },
1868
1869 /* ---- card 0x64 ---------------------------------- */
1870 [BTTV_BOARD_HERCULES_SM_TV] = {
1871 .name = "Hercules Smart TV Stereo",
1872 .video_inputs = 4,
1873 /* .audio_inputs= 1, */
1874 .svhs = 2,
1875 .gpiomask = 0x00,
1876 .muxsel = MUXSEL(2, 3, 1, 1),
1877 .no_msp34xx = 1,
1878 .pll = PLL_28,
1879 .tuner_type = TUNER_PHILIPS_PAL,
1880 .tuner_addr = ADDR_UNSET,
1881 /* Notes:
1882 - card lacks subsystem ID
1883 - stereo variant w/ daughter board with tda9874a @0xb0
1884 - Audio Routing:
1885 always from tda9874 independent of GPIO (?)
1886 external line in: unknown
1887 - Other chips: em78p156elp @ 0x96 (probably IR remote control)
1888 hef4053 (instead 4052) for unknown function
1889 */
1890 },
1891 [BTTV_BOARD_PACETV] = {
1892 .name = "Pace TV & Radio Card",
1893 .video_inputs = 4,
1894 /* .audio_inputs= 1, */
1895 .svhs = 2,
1896 /* Tuner, CVid, SVid, CVid over SVid connector */
1897 .muxsel = MUXSEL(2, 3, 1, 1),
1898 .gpiomask = 0,
1899 .no_tda7432 = 1,
1900 .tuner_type = TUNER_PHILIPS_PAL_I,
1901 .tuner_addr = ADDR_UNSET,
1902 .has_radio = 1,
1903 .pll = PLL_28,
1904 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id
1905 only internal line out: (4pin header) RGGL
1906 Radio must be decoded by msp3410d (not routed through)*/
1907 /*
1908 .digital_mode = DIGITAL_MODE_CAMERA, todo!
1909 */
1910 },
1911 [BTTV_BOARD_IVC200] = {
1912 /* Chris Willing <chris@vislab.usyd.edu.au> */
1913 .name = "IVC-200",
1914 .video_inputs = 1,
1915 /* .audio_inputs= 0, */
1916 .tuner_type = TUNER_ABSENT,
1917 .tuner_addr = ADDR_UNSET,
1918 .svhs = NO_SVHS,
1919 .gpiomask = 0xdf,
1920 .muxsel = MUXSEL(2),
1921 .pll = PLL_28,
1922 },
1923 [BTTV_BOARD_IVCE8784] = {
1924 .name = "IVCE-8784",
1925 .video_inputs = 1,
1926 /* .audio_inputs= 0, */
1927 .tuner_type = TUNER_ABSENT,
1928 .tuner_addr = ADDR_UNSET,
1929 .svhs = NO_SVHS,
1930 .gpiomask = 0xdf,
1931 .muxsel = MUXSEL(2),
1932 .pll = PLL_28,
1933 },
1934 [BTTV_BOARD_XGUARD] = {
1935 .name = "Grand X-Guard / Trust 814PCI",
1936 .video_inputs = 16,
1937 /* .audio_inputs= 0, */
1938 .svhs = NO_SVHS,
1939 .tuner_type = TUNER_ABSENT,
1940 .tuner_addr = ADDR_UNSET,
1941 .gpiomask2 = 0xff,
1942 .muxsel = MUXSEL(2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0),
1943 .muxsel_hook = xguard_muxsel,
1944 .no_msp34xx = 1,
1945 .no_tda7432 = 1,
1946 .pll = PLL_28,
1947 },
1948
1949 /* ---- card 0x68 ---------------------------------- */
1950 [BTTV_BOARD_NEBULA_DIGITV] = {
1951 .name = "Nebula Electronics DigiTV",
1952 .video_inputs = 1,
1953 .svhs = NO_SVHS,
1954 .muxsel = MUXSEL(2, 3, 1, 0),
1955 .no_msp34xx = 1,
1956 .no_tda7432 = 1,
1957 .pll = PLL_28,
1958 .tuner_type = TUNER_ABSENT,
1959 .tuner_addr = ADDR_UNSET,
1960 .has_dvb = 1,
1961 .has_remote = 1,
1962 .gpiomask = 0x1b,
1963 .no_gpioirq = 1,
1964 },
1965 [BTTV_BOARD_PV143] = {
1966 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */
1967 .name = "ProVideo PV143",
1968 .video_inputs = 4,
1969 /* .audio_inputs= 0, */
1970 .svhs = NO_SVHS,
1971 .gpiomask = 0,
1972 .muxsel = MUXSEL(2, 3, 1, 0),
1973 .gpiomux = { 0 },
1974 .no_msp34xx = 1,
1975 .pll = PLL_28,
1976 .tuner_type = TUNER_ABSENT,
1977 .tuner_addr = ADDR_UNSET,
1978 },
1979 [BTTV_BOARD_VD009X1_VD011_MINIDIN] = {
1980 /* M.Klahr@phytec.de */
1981 .name = "PHYTEC VD-009-X1 VD-011 MiniDIN (bt878)",
1982 .video_inputs = 4,
1983 /* .audio_inputs= 0, */
1984 .svhs = 3,
1985 .gpiomask = 0x00,
1986 .muxsel = MUXSEL(2, 3, 1, 0),
1987 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
1988 .pll = PLL_28,
1989 .tuner_type = TUNER_ABSENT,
1990 .tuner_addr = ADDR_UNSET,
1991 },
1992 [BTTV_BOARD_VD009X1_VD011_COMBI] = {
1993 .name = "PHYTEC VD-009-X1 VD-011 Combi (bt878)",
1994 .video_inputs = 4,
1995 /* .audio_inputs= 0, */
1996 .svhs = 3,
1997 .gpiomask = 0x00,
1998 .muxsel = MUXSEL(2, 3, 1, 1),
1999 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2000 .pll = PLL_28,
2001 .tuner_type = TUNER_ABSENT,
2002 .tuner_addr = ADDR_UNSET,
2003 },
2004
2005 /* ---- card 0x6c ---------------------------------- */
2006 [BTTV_BOARD_VD009_MINIDIN] = {
2007 .name = "PHYTEC VD-009 MiniDIN (bt878)",
2008 .video_inputs = 10,
2009 /* .audio_inputs= 0, */
2010 .svhs = 9,
2011 .gpiomask = 0x00,
2012 .gpiomask2 = 0x03, /* used for external video mux */
2013 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 0),
2014 .muxsel_hook = phytec_muxsel,
2015 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2016 .pll = PLL_28,
2017 .tuner_type = TUNER_ABSENT,
2018 .tuner_addr = ADDR_UNSET,
2019 },
2020 [BTTV_BOARD_VD009_COMBI] = {
2021 .name = "PHYTEC VD-009 Combi (bt878)",
2022 .video_inputs = 10,
2023 /* .audio_inputs= 0, */
2024 .svhs = 9,
2025 .gpiomask = 0x00,
2026 .gpiomask2 = 0x03, /* used for external video mux */
2027 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
2028 .muxsel_hook = phytec_muxsel,
2029 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2030 .pll = PLL_28,
2031 .tuner_type = TUNER_ABSENT,
2032 .tuner_addr = ADDR_UNSET,
2033 },
2034 [BTTV_BOARD_IVC100] = {
2035 .name = "IVC-100",
2036 .video_inputs = 4,
2037 /* .audio_inputs= 0, */
2038 .tuner_type = TUNER_ABSENT,
2039 .tuner_addr = ADDR_UNSET,
2040 .svhs = NO_SVHS,
2041 .gpiomask = 0xdf,
2042 .muxsel = MUXSEL(2, 3, 1, 0),
2043 .pll = PLL_28,
2044 },
2045 [BTTV_BOARD_IVC120] = {
2046 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */
2047 .name = "IVC-120G",
2048 .video_inputs = 16,
2049 /* .audio_inputs= 0, */
2050 .tuner_type = TUNER_ABSENT,
2051 .tuner_addr = ADDR_UNSET,
2052 .svhs = NO_SVHS, /* card has no svhs */
2053 .no_msp34xx = 1,
2054 .no_tda7432 = 1,
2055 .gpiomask = 0x00,
2056 .muxsel = MUXSEL(0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0),
2057 .muxsel_hook = ivc120_muxsel,
2058 .pll = PLL_28,
2059 },
2060
2061 /* ---- card 0x70 ---------------------------------- */
2062 [BTTV_BOARD_PC_HDTV] = {
2063 .name = "pcHDTV HD-2000 TV",
2064 .video_inputs = 4,
2065 /* .audio_inputs= 1, */
2066 .svhs = 2,
2067 .muxsel = MUXSEL(2, 3, 1, 0),
2068 .tuner_type = TUNER_PHILIPS_FCV1236D,
2069 .tuner_addr = ADDR_UNSET,
2070 .has_dvb = 1,
2071 },
2072 [BTTV_BOARD_TWINHAN_DST] = {
2073 .name = "Twinhan DST + clones",
2074 .no_msp34xx = 1,
2075 .no_tda7432 = 1,
2076 .tuner_type = TUNER_ABSENT,
2077 .tuner_addr = ADDR_UNSET,
2078 .no_video = 1,
2079 .has_dvb = 1,
2080 },
2081 [BTTV_BOARD_WINFASTVC100] = {
2082 .name = "Winfast VC100",
2083 .video_inputs = 3,
2084 /* .audio_inputs= 0, */
2085 .svhs = 1,
2086 /* Vid In, SVid In, Vid over SVid in connector */
2087 .muxsel = MUXSEL(3, 1, 1, 3),
2088 .no_msp34xx = 1,
2089 .no_tda7432 = 1,
2090 .tuner_type = TUNER_ABSENT,
2091 .tuner_addr = ADDR_UNSET,
2092 .pll = PLL_28,
2093 },
2094 [BTTV_BOARD_TEV560] = {
2095 .name = "Teppro TEV-560/InterVision IV-560",
2096 .video_inputs = 3,
2097 /* .audio_inputs= 1, */
2098 .svhs = 2,
2099 .gpiomask = 3,
2100 .muxsel = MUXSEL(2, 3, 1, 1),
2101 .gpiomux = { 1, 1, 1, 1 },
2102 .tuner_type = TUNER_PHILIPS_PAL,
2103 .tuner_addr = ADDR_UNSET,
2104 .pll = PLL_35,
2105 },
2106
2107 /* ---- card 0x74 ---------------------------------- */
2108 [BTTV_BOARD_SIMUS_GVC1100] = {
2109 .name = "SIMUS GVC1100",
2110 .video_inputs = 4,
2111 /* .audio_inputs= 0, */
2112 .svhs = NO_SVHS,
2113 .tuner_type = TUNER_ABSENT,
2114 .tuner_addr = ADDR_UNSET,
2115 .pll = PLL_28,
2116 .muxsel = MUXSEL(2, 2, 2, 2),
2117 .gpiomask = 0x3F,
2118 .muxsel_hook = gvc1100_muxsel,
2119 },
2120 [BTTV_BOARD_NGSTV_PLUS] = {
2121 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
2122 .name = "NGS NGSTV+",
2123 .video_inputs = 3,
2124 .svhs = 2,
2125 .gpiomask = 0x008007,
2126 .muxsel = MUXSEL(2, 3, 0, 0),
2127 .gpiomux = { 0, 0, 0, 0 },
2128 .gpiomute = 0x000003,
2129 .pll = PLL_28,
2130 .tuner_type = TUNER_PHILIPS_PAL,
2131 .tuner_addr = ADDR_UNSET,
2132 .has_remote = 1,
2133 },
2134 [BTTV_BOARD_LMLBT4] = {
2135 /* http://linuxmedialabs.com */
2136 .name = "LMLBT4",
2137 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */
2138 /* .audio_inputs= 0, */
2139 .svhs = NO_SVHS,
2140 .muxsel = MUXSEL(2, 3, 1, 0),
2141 .no_msp34xx = 1,
2142 .no_tda7432 = 1,
2143 .tuner_type = TUNER_ABSENT,
2144 .tuner_addr = ADDR_UNSET,
2145 },
2146 [BTTV_BOARD_TEKRAM_M205] = {
2147 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */
2148 .name = "Tekram M205 PRO",
2149 .video_inputs = 3,
2150 /* .audio_inputs= 1, */
2151 .tuner_type = TUNER_PHILIPS_PAL,
2152 .tuner_addr = ADDR_UNSET,
2153 .svhs = 2,
2154 .gpiomask = 0x68,
2155 .muxsel = MUXSEL(2, 3, 1),
2156 .gpiomux = { 0x68, 0x68, 0x61, 0x61 },
2157 .pll = PLL_28,
2158 },
2159
2160 /* ---- card 0x78 ---------------------------------- */
2161 [BTTV_BOARD_CONTVFMI] = {
2162 /* Javier Cendan Ares <jcendan@lycos.es> */
2163 /* bt878 TV + FM without subsystem ID */
2164 .name = "Conceptronic CONTVFMi",
2165 .video_inputs = 3,
2166 /* .audio_inputs= 1, */
2167 .svhs = 2,
2168 .gpiomask = 0x008007,
2169 .muxsel = MUXSEL(2, 3, 1, 1),
2170 .gpiomux = { 0, 1, 2, 2 },
2171 .gpiomute = 3,
2172 .pll = PLL_28,
2173 .tuner_type = TUNER_PHILIPS_PAL,
2174 .tuner_addr = ADDR_UNSET,
2175 .has_remote = 1,
2176 .has_radio = 1,
2177 },
2178 [BTTV_BOARD_PICOLO_TETRA_CHIP] = {
2179 /*Eric DEBIEF <debief@telemsa.com>*/
2180 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled*/
2181 /*adds picolo_tetra_muxsel(), picolo_tetra_init(), the following declaration*/
2182 /*structure and #define BTTV_BOARD_PICOLO_TETRA_CHIP 0x79 in bttv.h*/
2183 .name = "Euresys Picolo Tetra",
2184 .video_inputs = 4,
2185 /* .audio_inputs= 0, */
2186 .svhs = NO_SVHS,
2187 .gpiomask = 0,
2188 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
2189 .no_msp34xx = 1,
2190 .no_tda7432 = 1,
2191 /*878A input is always MUX0, see above.*/
2192 .muxsel = MUXSEL(2, 2, 2, 2),
2193 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2194 .pll = PLL_28,
2195 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
2196 .tuner_type = TUNER_ABSENT,
2197 .tuner_addr = ADDR_UNSET,
2198 },
2199 [BTTV_BOARD_SPIRIT_TV] = {
2200 /* Spirit TV Tuner from http://spiritmodems.com.au */
2201 /* Stafford Goodsell <surge@goliath.homeunix.org> */
2202 .name = "Spirit TV Tuner",
2203 .video_inputs = 3,
2204 /* .audio_inputs= 1, */
2205 .svhs = 2,
2206 .gpiomask = 0x0000000f,
2207 .muxsel = MUXSEL(2, 1, 1),
2208 .gpiomux = { 0x02, 0x00, 0x00, 0x00 },
2209 .tuner_type = TUNER_TEMIC_PAL,
2210 .tuner_addr = ADDR_UNSET,
2211 .no_msp34xx = 1,
2212 },
2213 [BTTV_BOARD_AVDVBT_771] = {
2214 /* Wolfram Joost <wojo@frokaschwei.de> */
2215 .name = "AVerMedia AVerTV DVB-T 771",
2216 .video_inputs = 2,
2217 .svhs = 1,
2218 .tuner_type = TUNER_ABSENT,
2219 .tuner_addr = ADDR_UNSET,
2220 .muxsel = MUXSEL(3, 3),
2221 .no_msp34xx = 1,
2222 .no_tda7432 = 1,
2223 .pll = PLL_28,
2224 .has_dvb = 1,
2225 .no_gpioirq = 1,
2226 .has_remote = 1,
2227 },
2228 /* ---- card 0x7c ---------------------------------- */
2229 [BTTV_BOARD_AVDVBT_761] = {
2230 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */
2231 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */
2232 .name = "AverMedia AverTV DVB-T 761",
2233 .video_inputs = 2,
2234 .svhs = 1,
2235 .muxsel = MUXSEL(3, 1, 2, 0), /* Comp0, S-Video, ?, ? */
2236 .no_msp34xx = 1,
2237 .no_tda7432 = 1,
2238 .pll = PLL_28,
2239 .tuner_type = TUNER_ABSENT,
2240 .tuner_addr = ADDR_UNSET,
2241 .has_dvb = 1,
2242 .no_gpioirq = 1,
2243 .has_remote = 1,
2244 },
2245 [BTTV_BOARD_MATRIX_VISIONSQ] = {
2246 /* andre.schwarz@matrix-vision.de */
2247 .name = "MATRIX Vision Sigma-SQ",
2248 .video_inputs = 16,
2249 /* .audio_inputs= 0, */
2250 .svhs = NO_SVHS,
2251 .gpiomask = 0x0,
2252 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3),
2253 .muxsel_hook = sigmaSQ_muxsel,
2254 .gpiomux = { 0 },
2255 .no_msp34xx = 1,
2256 .pll = PLL_28,
2257 .tuner_type = TUNER_ABSENT,
2258 .tuner_addr = ADDR_UNSET,
2259 },
2260 [BTTV_BOARD_MATRIX_VISIONSLC] = {
2261 /* andre.schwarz@matrix-vision.de */
2262 .name = "MATRIX Vision Sigma-SLC",
2263 .video_inputs = 4,
2264 /* .audio_inputs= 0, */
2265 .svhs = NO_SVHS,
2266 .gpiomask = 0x0,
2267 .muxsel = MUXSEL(2, 2, 2, 2),
2268 .muxsel_hook = sigmaSLC_muxsel,
2269 .gpiomux = { 0 },
2270 .no_msp34xx = 1,
2271 .pll = PLL_28,
2272 .tuner_type = TUNER_ABSENT,
2273 .tuner_addr = ADDR_UNSET,
2274 },
2275 /* BTTV_BOARD_APAC_VIEWCOMP */
2276 [BTTV_BOARD_APAC_VIEWCOMP] = {
2277 /* Attila Kondoros <attila.kondoros@chello.hu> */
2278 /* bt878 TV + FM 0x00000000 subsystem ID */
2279 .name = "APAC Viewcomp 878(AMAX)",
2280 .video_inputs = 2,
2281 /* .audio_inputs= 1, */
2282 .svhs = NO_SVHS,
2283 .gpiomask = 0xFF,
2284 .muxsel = MUXSEL(2, 3, 1, 1),
2285 .gpiomux = { 2, 0, 0, 0 },
2286 .gpiomute = 10,
2287 .pll = PLL_28,
2288 .tuner_type = TUNER_PHILIPS_PAL,
2289 .tuner_addr = ADDR_UNSET,
2290 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */
2291 .has_radio = 1, /* not every card has radio */
2292 },
2293
2294 /* ---- card 0x80 ---------------------------------- */
2295 [BTTV_BOARD_DVICO_DVBT_LITE] = {
2296 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
2297 .name = "DViCO FusionHDTV DVB-T Lite",
2298 .no_msp34xx = 1,
2299 .no_tda7432 = 1,
2300 .pll = PLL_28,
2301 .no_video = 1,
2302 .has_dvb = 1,
2303 .tuner_type = TUNER_ABSENT,
2304 .tuner_addr = ADDR_UNSET,
2305 },
2306 [BTTV_BOARD_VGEAR_MYVCD] = {
2307 /* Steven <photon38@pchome.com.tw> */
2308 .name = "V-Gear MyVCD",
2309 .video_inputs = 3,
2310 /* .audio_inputs= 1, */
2311 .svhs = 2,
2312 .gpiomask = 0x3f,
2313 .muxsel = MUXSEL(2, 3, 1, 0),
2314 .gpiomux = {0x31, 0x31, 0x31, 0x31 },
2315 .gpiomute = 0x31,
2316 .no_msp34xx = 1,
2317 .pll = PLL_28,
2318 .tuner_type = TUNER_PHILIPS_NTSC_M,
2319 .tuner_addr = ADDR_UNSET,
2320 .has_radio = 0,
2321 },
2322 [BTTV_BOARD_SUPER_TV] = {
2323 /* Rick C <cryptdragoon@gmail.com> */
2324 .name = "Super TV Tuner",
2325 .video_inputs = 4,
2326 /* .audio_inputs= 1, */
2327 .svhs = 2,
2328 .muxsel = MUXSEL(2, 3, 1, 0),
2329 .tuner_type = TUNER_PHILIPS_NTSC,
2330 .tuner_addr = ADDR_UNSET,
2331 .gpiomask = 0x008007,
2332 .gpiomux = { 0, 0x000001,0,0 },
2333 .has_radio = 1,
2334 },
2335 [BTTV_BOARD_TIBET_CS16] = {
2336 /* Chris Fanning <video4linux@haydon.net> */
2337 .name = "Tibet Systems 'Progress DVR' CS16",
2338 .video_inputs = 16,
2339 /* .audio_inputs= 0, */
2340 .svhs = NO_SVHS,
2341 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2342 .pll = PLL_28,
2343 .no_msp34xx = 1,
2344 .no_tda7432 = 1,
2345 .tuner_type = TUNER_ABSENT,
2346 .tuner_addr = ADDR_UNSET,
2347 .muxsel_hook = tibetCS16_muxsel,
2348 },
2349 [BTTV_BOARD_KODICOM_4400R] = {
2350 /* Bill Brack <wbrack@mmm.com.hk> */
2351 /*
2352 * Note that, because of the card's wiring, the "master"
2353 * BT878A chip (i.e. the one which controls the analog switch
2354 * and must use this card type) is the 2nd one detected. The
2355 * other 3 chips should use card type 0x85, whose description
2356 * follows this one. There is a EEPROM on the card (which is
2357 * connected to the I2C of one of those other chips), but is
2358 * not currently handled. There is also a facility for a
2359 * "monitor", which is also not currently implemented.
2360 */
2361 .name = "Kodicom 4400R (master)",
2362 .video_inputs = 16,
2363 /* .audio_inputs= 0, */
2364 .tuner_type = TUNER_ABSENT,
2365 .tuner_addr = ADDR_UNSET,
2366 .svhs = NO_SVHS,
2367 /* GPIO bits 0-9 used for analog switch:
2368 * 00 - 03: camera selector
2369 * 04 - 06: channel (controller) selector
2370 * 07: data (1->on, 0->off)
2371 * 08: strobe
2372 * 09: reset
2373 * bit 16 is input from sync separator for the channel
2374 */
2375 .gpiomask = 0x0003ff,
2376 .no_gpioirq = 1,
2377 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2378 .pll = PLL_28,
2379 .no_msp34xx = 1,
2380 .no_tda7432 = 1,
2381 .muxsel_hook = kodicom4400r_muxsel,
2382 },
2383 [BTTV_BOARD_KODICOM_4400R_SL] = {
2384 /* Bill Brack <wbrack@mmm.com.hk> */
2385 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
2386 * one which controls the analog switch, and must use the card type)
2387 * is the 2nd one detected. The other 3 chips should use this card
2388 * type
2389 */
2390 .name = "Kodicom 4400R (slave)",
2391 .video_inputs = 16,
2392 /* .audio_inputs= 0, */
2393 .tuner_type = TUNER_ABSENT,
2394 .tuner_addr = ADDR_UNSET,
2395 .svhs = NO_SVHS,
2396 .gpiomask = 0x010000,
2397 .no_gpioirq = 1,
2398 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2399 .pll = PLL_28,
2400 .no_msp34xx = 1,
2401 .no_tda7432 = 1,
2402 .muxsel_hook = kodicom4400r_muxsel,
2403 },
2404 /* ---- card 0x86---------------------------------- */
2405 [BTTV_BOARD_ADLINK_RTV24] = {
2406 /* Michael Henson <mhenson@clarityvi.com> */
2407 /* Adlink RTV24 with special unlock codes */
2408 .name = "Adlink RTV24",
2409 .video_inputs = 4,
2410 /* .audio_inputs= 1, */
2411 .svhs = 2,
2412 .muxsel = MUXSEL(2, 3, 1, 0),
2413 .tuner_type = UNSET,
2414 .tuner_addr = ADDR_UNSET,
2415 .pll = PLL_28,
2416 },
2417 /* ---- card 0x87---------------------------------- */
2418 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = {
2419 /* Michael Krufky <mkrufky@linuxtv.org> */
2420 .name = "DViCO FusionHDTV 5 Lite",
2421 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */
2422 .tuner_addr = ADDR_UNSET,
2423 .video_inputs = 3,
2424 /* .audio_inputs= 1, */
2425 .svhs = 2,
2426 .muxsel = MUXSEL(2, 3, 1),
2427 .gpiomask = 0x00e00007,
2428 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2429 .gpiomute = 0x00c00007,
2430 .no_msp34xx = 1,
2431 .no_tda7432 = 1,
2432 .has_dvb = 1,
2433 },
2434 /* ---- card 0x88---------------------------------- */
2435 [BTTV_BOARD_ACORP_Y878F] = {
2436 /* Mauro Carvalho Chehab <mchehab@kernel.org> */
2437 .name = "Acorp Y878F",
2438 .video_inputs = 3,
2439 /* .audio_inputs= 1, */
2440 .svhs = 2,
2441 .gpiomask = 0x01fe00,
2442 .muxsel = MUXSEL(2, 3, 1, 1),
2443 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
2444 .gpiomute = 0x002000,
2445 .pll = PLL_28,
2446 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF,
2447 .tuner_addr = 0xc1 >>1,
2448 .has_radio = 1,
2449 },
2450 /* ---- card 0x89 ---------------------------------- */
2451 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = {
2452 .name = "Conceptronic CTVFMi v2",
2453 .video_inputs = 3,
2454 /* .audio_inputs= 1, */
2455 .svhs = 2,
2456 .gpiomask = 0x001c0007,
2457 .muxsel = MUXSEL(2, 3, 1, 1),
2458 .gpiomux = { 0, 1, 2, 2 },
2459 .gpiomute = 3,
2460 .pll = PLL_28,
2461 .tuner_type = TUNER_TENA_9533_DI,
2462 .tuner_addr = ADDR_UNSET,
2463 .has_remote = 1,
2464 .has_radio = 1,
2465 },
2466 /* ---- card 0x8a ---------------------------------- */
2467 [BTTV_BOARD_PV_BT878P_2E] = {
2468 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)",
2469 .video_inputs = 5,
2470 /* .audio_inputs= 1, */
2471 .svhs = 3,
2472 .has_dig_in = 1,
2473 .gpiomask = 0x01fe00,
2474 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
2475 /* .digital_mode= DIGITAL_MODE_CAMERA, */
2476 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 },
2477 .gpiomute = 0x12400,
2478 .no_msp34xx = 1,
2479 .pll = PLL_28,
2480 .tuner_type = TUNER_LG_PAL_FM,
2481 .tuner_addr = ADDR_UNSET,
2482 .has_remote = 1,
2483 },
2484 /* ---- card 0x8b ---------------------------------- */
2485 [BTTV_BOARD_PV_M4900] = {
2486 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */
2487 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900",
2488 .video_inputs = 3,
2489 /* .audio_inputs= 1, */
2490 .svhs = 2,
2491 .gpiomask = 0x3f,
2492 .muxsel = MUXSEL(2, 3, 1, 1),
2493 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
2494 .gpiomute = 0x29,
2495 .no_msp34xx = 1,
2496 .pll = PLL_28,
2497 .tuner_type = TUNER_YMEC_TVF_5533MF,
2498 .tuner_addr = ADDR_UNSET,
2499 .has_radio = 1,
2500 .has_remote = 1,
2501 },
2502 /* ---- card 0x8c ---------------------------------- */
2503 /* Has four Bt878 chips behind a PCI bridge, each chip has:
2504 one external BNC composite input (mux 2)
2505 three internal composite inputs (unknown muxes)
2506 an 18-bit stereo A/D (CS5331A), which has:
2507 one external stereo unbalanced (RCA) audio connection
2508 one (or 3?) internal stereo balanced (XLR) audio connection
2509 input is selected via gpio to a 14052B mux
2510 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300)
2511 gain is controlled via an X9221A chip on the I2C bus @0x28
2512 sample rate is controlled via gpio to an MK1413S
2513 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3)
2514 There is neither a tuner nor an svideo input. */
2515 [BTTV_BOARD_OSPREY440] = {
2516 .name = "Osprey 440",
2517 .video_inputs = 4,
2518 /* .audio_inputs= 2, */
2519 .svhs = NO_SVHS,
2520 .muxsel = MUXSEL(2, 3, 0, 1), /* 3,0,1 are guesses */
2521 .gpiomask = 0x303,
2522 .gpiomute = 0x000, /* int + 32kHz */
2523 .gpiomux = { 0, 0, 0x000, 0x100},
2524 .pll = PLL_28,
2525 .tuner_type = TUNER_ABSENT,
2526 .tuner_addr = ADDR_UNSET,
2527 .no_msp34xx = 1,
2528 .no_tda7432 = 1,
2529 },
2530 /* ---- card 0x8d ---------------------------------- */
2531 [BTTV_BOARD_ASOUND_SKYEYE] = {
2532 .name = "Asound Skyeye PCTV",
2533 .video_inputs = 3,
2534 /* .audio_inputs= 1, */
2535 .svhs = 2,
2536 .gpiomask = 15,
2537 .muxsel = MUXSEL(2, 3, 1, 1),
2538 .gpiomux = { 2, 0, 0, 0 },
2539 .gpiomute = 1,
2540 .pll = PLL_28,
2541 .tuner_type = TUNER_PHILIPS_NTSC,
2542 .tuner_addr = ADDR_UNSET,
2543 },
2544 /* ---- card 0x8e ---------------------------------- */
2545 [BTTV_BOARD_SABRENT_TVFM] = {
2546 .name = "Sabrent TV-FM (bttv version)",
2547 .video_inputs = 3,
2548 /* .audio_inputs= 1, */
2549 .svhs = 2,
2550 .gpiomask = 0x108007,
2551 .muxsel = MUXSEL(2, 3, 1, 1),
2552 .gpiomux = { 100000, 100002, 100002, 100000 },
2553 .no_msp34xx = 1,
2554 .no_tda7432 = 1,
2555 .pll = PLL_28,
2556 .tuner_type = TUNER_TNF_5335MF,
2557 .tuner_addr = ADDR_UNSET,
2558 .has_radio = 1,
2559 },
2560 /* ---- card 0x8f ---------------------------------- */
2561 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = {
2562 .name = "Hauppauge ImpactVCB (bt878)",
2563 .video_inputs = 4,
2564 /* .audio_inputs= 0, */
2565 .svhs = NO_SVHS,
2566 .gpiomask = 0x0f, /* old: 7 */
2567 .muxsel = MUXSEL(0, 1, 3, 2), /* Composite 0-3 */
2568 .no_msp34xx = 1,
2569 .no_tda7432 = 1,
2570 .tuner_type = TUNER_ABSENT,
2571 .tuner_addr = ADDR_UNSET,
2572 },
2573 [BTTV_BOARD_MACHTV_MAGICTV] = {
2574 /* Julian Calaby <julian.calaby@gmail.com>
2575 * Slightly different from original MachTV definition (0x60)
2576
2577 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it
2578 * stuffs up remote chip. Bug is a pin on the jaecs is not set
2579 * properly (methinks) causing no keyup bits being set */
2580
2581 .name = "MagicTV", /* rebranded MachTV */
2582 .video_inputs = 3,
2583 /* .audio_inputs= 1, */
2584 .svhs = 2,
2585 .gpiomask = 7,
2586 .muxsel = MUXSEL(2, 3, 1, 1),
2587 .gpiomux = { 0, 1, 2, 3 },
2588 .gpiomute = 4,
2589 .tuner_type = TUNER_TEMIC_4009FR5_PAL,
2590 .tuner_addr = ADDR_UNSET,
2591 .pll = PLL_28,
2592 .has_radio = 1,
2593 .has_remote = 1,
2594 },
2595 [BTTV_BOARD_SSAI_SECURITY] = {
2596 .name = "SSAI Security Video Interface",
2597 .video_inputs = 4,
2598 /* .audio_inputs= 0, */
2599 .svhs = NO_SVHS,
2600 .muxsel = MUXSEL(0, 1, 2, 3),
2601 .tuner_type = TUNER_ABSENT,
2602 .tuner_addr = ADDR_UNSET,
2603 },
2604 [BTTV_BOARD_SSAI_ULTRASOUND] = {
2605 .name = "SSAI Ultrasound Video Interface",
2606 .video_inputs = 2,
2607 /* .audio_inputs= 0, */
2608 .svhs = 1,
2609 .muxsel = MUXSEL(2, 0, 1, 3),
2610 .tuner_type = TUNER_ABSENT,
2611 .tuner_addr = ADDR_UNSET,
2612 },
2613 /* ---- card 0x94---------------------------------- */
2614 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = {
2615 .name = "DViCO FusionHDTV 2",
2616 .tuner_type = TUNER_PHILIPS_FCV1236D,
2617 .tuner_addr = ADDR_UNSET,
2618 .video_inputs = 3,
2619 /* .audio_inputs= 1, */
2620 .svhs = 2,
2621 .muxsel = MUXSEL(2, 3, 1),
2622 .gpiomask = 0x00e00007,
2623 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2624 .gpiomute = 0x00c00007,
2625 .no_msp34xx = 1,
2626 .no_tda7432 = 1,
2627 },
2628 /* ---- card 0x95---------------------------------- */
2629 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = {
2630 .name = "Typhoon TV-Tuner PCI (50684)",
2631 .video_inputs = 3,
2632 /* .audio_inputs= 1, */
2633 .svhs = 2,
2634 .gpiomask = 0x3014f,
2635 .muxsel = MUXSEL(2, 3, 1, 1),
2636 .gpiomux = { 0x20001,0x10001, 0, 0 },
2637 .gpiomute = 10,
2638 .pll = PLL_28,
2639 .tuner_type = TUNER_PHILIPS_PAL_I,
2640 .tuner_addr = ADDR_UNSET,
2641 },
2642 [BTTV_BOARD_GEOVISION_GV600] = {
2643 /* emhn@usb.ve */
2644 .name = "Geovision GV-600",
2645 .video_inputs = 16,
2646 /* .audio_inputs= 0, */
2647 .svhs = NO_SVHS,
2648 .gpiomask = 0x0,
2649 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2650 .muxsel_hook = geovision_muxsel,
2651 .gpiomux = { 0 },
2652 .no_msp34xx = 1,
2653 .pll = PLL_28,
2654 .tuner_type = TUNER_ABSENT,
2655 .tuner_addr = ADDR_UNSET,
2656 },
2657 [BTTV_BOARD_KOZUMI_KTV_01C] = {
2658 /* Mauro Lacy <mauro@lacy.com.ar>
2659 * Based on MagicTV and Conceptronic CONTVFMi */
2660
2661 .name = "Kozumi KTV-01C",
2662 .video_inputs = 3,
2663 /* .audio_inputs= 1, */
2664 .svhs = 2,
2665 .gpiomask = 0x008007,
2666 .muxsel = MUXSEL(2, 3, 1, 1),
2667 .gpiomux = { 0, 1, 2, 2 }, /* CONTVFMi */
2668 .gpiomute = 3, /* CONTVFMi */
2669 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */
2670 .tuner_addr = ADDR_UNSET,
2671 .pll = PLL_28,
2672 .has_radio = 1,
2673 .has_remote = 1,
2674 },
2675 [BTTV_BOARD_ENLTV_FM_2] = {
2676 /* Encore TV Tuner Pro ENL TV-FM-2
2677 Mauro Carvalho Chehab <mchehab@kernel.org> */
2678 .name = "Encore ENL TV-FM-2",
2679 .video_inputs = 3,
2680 /* .audio_inputs= 1, */
2681 .svhs = 2,
2682 /* bit 6 -> IR disabled
2683 bit 18/17 = 00 -> mute
2684 01 -> enable external audio input
2685 10 -> internal audio input (mono?)
2686 11 -> internal audio input
2687 */
2688 .gpiomask = 0x060040,
2689 .muxsel = MUXSEL(2, 3, 3),
2690 .gpiomux = { 0x60000, 0x60000, 0x20000, 0x20000 },
2691 .gpiomute = 0,
2692 .tuner_type = TUNER_TCL_MF02GIP_5N,
2693 .tuner_addr = ADDR_UNSET,
2694 .pll = PLL_28,
2695 .has_radio = 1,
2696 .has_remote = 1,
2697 },
2698 [BTTV_BOARD_VD012] = {
2699 /* D.Heer@Phytec.de */
2700 .name = "PHYTEC VD-012 (bt878)",
2701 .video_inputs = 4,
2702 /* .audio_inputs= 0, */
2703 .svhs = NO_SVHS,
2704 .gpiomask = 0x00,
2705 .muxsel = MUXSEL(0, 2, 3, 1),
2706 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2707 .pll = PLL_28,
2708 .tuner_type = TUNER_ABSENT,
2709 .tuner_addr = ADDR_UNSET,
2710 },
2711 [BTTV_BOARD_VD012_X1] = {
2712 /* D.Heer@Phytec.de */
2713 .name = "PHYTEC VD-012-X1 (bt878)",
2714 .video_inputs = 4,
2715 /* .audio_inputs= 0, */
2716 .svhs = 3,
2717 .gpiomask = 0x00,
2718 .muxsel = MUXSEL(2, 3, 1),
2719 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2720 .pll = PLL_28,
2721 .tuner_type = TUNER_ABSENT,
2722 .tuner_addr = ADDR_UNSET,
2723 },
2724 [BTTV_BOARD_VD012_X2] = {
2725 /* D.Heer@Phytec.de */
2726 .name = "PHYTEC VD-012-X2 (bt878)",
2727 .video_inputs = 4,
2728 /* .audio_inputs= 0, */
2729 .svhs = 3,
2730 .gpiomask = 0x00,
2731 .muxsel = MUXSEL(3, 2, 1),
2732 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2733 .pll = PLL_28,
2734 .tuner_type = TUNER_ABSENT,
2735 .tuner_addr = ADDR_UNSET,
2736 },
2737 [BTTV_BOARD_GEOVISION_GV800S] = {
2738 /* Bruno Christo <bchristo@inf.ufsm.br>
2739 *
2740 * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2741 * 1 audio input per BT878A = 4 audio inputs
2742 * 4 video inputs per BT878A = 16 video inputs
2743 * This is the first BT878A chip of the GV-800(S). It's the
2744 * "master" chip and it controls the video inputs through an
2745 * analog multiplexer (a CD22M3494) via some GPIO pins. The
2746 * slaves should use card type 0x9e (following this one).
2747 * There is a EEPROM on the card which is currently not handled.
2748 * The audio input is not working yet.
2749 */
2750 .name = "Geovision GV-800(S) (master)",
2751 .video_inputs = 4,
2752 /* .audio_inputs= 1, */
2753 .tuner_type = TUNER_ABSENT,
2754 .tuner_addr = ADDR_UNSET,
2755 .svhs = NO_SVHS,
2756 .gpiomask = 0xf107f,
2757 .no_gpioirq = 1,
2758 .muxsel = MUXSEL(2, 2, 2, 2),
2759 .pll = PLL_28,
2760 .no_msp34xx = 1,
2761 .no_tda7432 = 1,
2762 .muxsel_hook = gv800s_muxsel,
2763 },
2764 [BTTV_BOARD_GEOVISION_GV800S_SL] = {
2765 /* Bruno Christo <bchristo@inf.ufsm.br>
2766 *
2767 * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2768 * 1 audio input per BT878A = 4 audio inputs
2769 * 4 video inputs per BT878A = 16 video inputs
2770 * The 3 other BT878A chips are "slave" chips of the GV-800(S)
2771 * and should use this card type.
2772 * The audio input is not working yet.
2773 */
2774 .name = "Geovision GV-800(S) (slave)",
2775 .video_inputs = 4,
2776 /* .audio_inputs= 1, */
2777 .tuner_type = TUNER_ABSENT,
2778 .tuner_addr = ADDR_UNSET,
2779 .svhs = NO_SVHS,
2780 .gpiomask = 0x00,
2781 .no_gpioirq = 1,
2782 .muxsel = MUXSEL(2, 2, 2, 2),
2783 .pll = PLL_28,
2784 .no_msp34xx = 1,
2785 .no_tda7432 = 1,
2786 .muxsel_hook = gv800s_muxsel,
2787 },
2788 [BTTV_BOARD_PV183] = {
2789 .name = "ProVideo PV183", /* 0x9f */
2790 .video_inputs = 2,
2791 /* .audio_inputs= 0, */
2792 .svhs = NO_SVHS,
2793 .gpiomask = 0,
2794 .muxsel = MUXSEL(2, 3),
2795 .gpiomux = { 0 },
2796 .no_msp34xx = 1,
2797 .pll = PLL_28,
2798 .tuner_type = TUNER_ABSENT,
2799 .tuner_addr = ADDR_UNSET,
2800 },
2801 /* ---- card 0xa0---------------------------------- */
2802 [BTTV_BOARD_TVT_TD3116] = {
2803 .name = "Tongwei Video Technology TD-3116",
2804 .video_inputs = 16,
2805 .gpiomask = 0xc00ff,
2806 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2807 .muxsel_hook = td3116_muxsel,
2808 .svhs = NO_SVHS,
2809 .pll = PLL_28,
2810 .tuner_type = TUNER_ABSENT,
2811 },
2812 [BTTV_BOARD_APOSONIC_WDVR] = {
2813 .name = "Aposonic W-DVR",
2814 .video_inputs = 4,
2815 .svhs = NO_SVHS,
2816 .muxsel = MUXSEL(2, 3, 1, 0),
2817 .tuner_type = TUNER_ABSENT,
2818 },
2819 [BTTV_BOARD_ADLINK_MPG24] = {
2820 /* Adlink MPG24 */
2821 .name = "Adlink MPG24",
2822 .video_inputs = 1,
2823 /* .audio_inputs= 1, */
2824 .svhs = NO_SVHS,
2825 .muxsel = MUXSEL(2, 2, 2, 2),
2826 .tuner_type = UNSET,
2827 .tuner_addr = ADDR_UNSET,
2828 .pll = PLL_28,
2829 },
2830 [BTTV_BOARD_BT848_CAP_14] = {
2831 .name = "Bt848 Capture 14MHz",
2832 .video_inputs = 4,
2833 .svhs = 2,
2834 .muxsel = MUXSEL(2, 3, 1, 0),
2835 .pll = PLL_14,
2836 .tuner_type = TUNER_ABSENT,
2837 },
2838 [BTTV_BOARD_CYBERVISION_CV06] = {
2839 .name = "CyberVision CV06 (SV)",
2840 .video_inputs = 4,
2841 /* .audio_inputs= 0, */
2842 .svhs = NO_SVHS,
2843 .muxsel = MUXSEL(2, 3, 1, 0),
2844 .pll = PLL_28,
2845 .tuner_type = TUNER_ABSENT,
2846 .tuner_addr = ADDR_UNSET,
2847 },
2848 [BTTV_BOARD_KWORLD_VSTREAM_XPERT] = {
2849 /* Pojar George <geoubuntu@gmail.com> */
2850 .name = "Kworld V-Stream Xpert TV PVR878",
2851 .video_inputs = 3,
2852 /* .audio_inputs= 1, */
2853 .svhs = 2,
2854 .gpiomask = 0x001c0007,
2855 .muxsel = MUXSEL(2, 3, 1, 1),
2856 .gpiomux = { 0, 1, 2, 2 },
2857 .gpiomute = 3,
2858 .pll = PLL_28,
2859 .tuner_type = TUNER_TENA_9533_DI,
2860 .tuner_addr = ADDR_UNSET,
2861 .has_remote = 1,
2862 .has_radio = 1,
2863 },
2864 /* ---- card 0xa6---------------------------------- */
2865 [BTTV_BOARD_PCI_8604PW] = {
2866 /* PCI-8604PW with special unlock sequence */
2867 .name = "PCI-8604PW",
2868 .video_inputs = 2,
2869 /* .audio_inputs= 0, */
2870 .svhs = NO_SVHS,
2871 /* The second input is available on CN4, if populated.
2872 * The other 5x2 header (CN2?) connects to the same inputs
2873 * as the on-board BNCs */
2874 .muxsel = MUXSEL(2, 3),
2875 .tuner_type = TUNER_ABSENT,
2876 .no_msp34xx = 1,
2877 .no_tda7432 = 1,
2878 .pll = PLL_35,
2879 },
2880 };
2881
2882 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
2883
2884 /* ----------------------------------------------------------------------- */
2885
2886 static unsigned char eeprom_data[256];
2887
2888 /*
2889 * identify card
2890 */
bttv_idcard(struct bttv * btv)2891 void bttv_idcard(struct bttv *btv)
2892 {
2893 unsigned int gpiobits;
2894 int i,type;
2895
2896 /* read PCI subsystem ID */
2897 btv->cardid = btv->c.pci->subsystem_device << 16;
2898 btv->cardid |= btv->c.pci->subsystem_vendor;
2899
2900 if (0 != btv->cardid && 0xffffffff != btv->cardid) {
2901 /* look for the card */
2902 for (type = -1, i = 0; cards[i].id != 0; i++)
2903 if (cards[i].id == btv->cardid)
2904 type = i;
2905
2906 if (type != -1) {
2907 /* found it */
2908 pr_info("%d: detected: %s [card=%d], PCI subsystem ID is %04x:%04x\n",
2909 btv->c.nr, cards[type].name, cards[type].cardnr,
2910 btv->cardid & 0xffff,
2911 (btv->cardid >> 16) & 0xffff);
2912 btv->c.type = cards[type].cardnr;
2913 } else {
2914 /* 404 */
2915 pr_info("%d: subsystem: %04x:%04x (UNKNOWN)\n",
2916 btv->c.nr, btv->cardid & 0xffff,
2917 (btv->cardid >> 16) & 0xffff);
2918 pr_debug("please mail id, board name and the correct card= insmod option to linux-media@vger.kernel.org\n");
2919 }
2920 }
2921
2922 /* let the user override the autodetected type */
2923 if (card[btv->c.nr] < bttv_num_tvcards)
2924 btv->c.type=card[btv->c.nr];
2925
2926 /* print which card config we are using */
2927 pr_info("%d: using: %s [card=%d,%s]\n",
2928 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type,
2929 card[btv->c.nr] < bttv_num_tvcards
2930 ? "insmod option" : "autodetected");
2931
2932 /* overwrite gpio stuff ?? */
2933 if (UNSET == audioall && UNSET == audiomux[0])
2934 return;
2935
2936 if (UNSET != audiomux[0]) {
2937 gpiobits = 0;
2938 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2939 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i];
2940 gpiobits |= audiomux[i];
2941 }
2942 } else {
2943 gpiobits = audioall;
2944 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2945 bttv_tvcards[btv->c.type].gpiomux[i] = audioall;
2946 }
2947 }
2948 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
2949 pr_info("%d: gpio config override: mask=0x%x, mux=",
2950 btv->c.nr, bttv_tvcards[btv->c.type].gpiomask);
2951 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2952 pr_cont("%s0x%x",
2953 i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]);
2954 }
2955 pr_cont("\n");
2956 }
2957
2958 /*
2959 * (most) board specific initialisations goes here
2960 */
2961
2962 /* Some Modular Technology cards have an eeprom, but no subsystem ID */
identify_by_eeprom(struct bttv * btv,unsigned char eeprom_data[256])2963 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
2964 {
2965 int type = -1;
2966
2967 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
2968 type = BTTV_BOARD_MODTEC_205;
2969 else if (0 == strncmp(eeprom_data+20,"Picolo",7))
2970 type = BTTV_BOARD_EURESYS_PICOLO;
2971 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
2972 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */
2973
2974 if (-1 != type) {
2975 btv->c.type = type;
2976 pr_info("%d: detected by eeprom: %s [card=%d]\n",
2977 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
2978 }
2979 }
2980
flyvideo_gpio(struct bttv * btv)2981 static void flyvideo_gpio(struct bttv *btv)
2982 {
2983 int gpio, has_remote, has_radio, is_capture_only;
2984 int is_lr90, has_tda9820_tda9821;
2985 int tuner_type = UNSET, ttype;
2986
2987 gpio_inout(0xffffff, 0);
2988 udelay(8); /* without this we would see the 0x1800 mask */
2989 gpio = gpio_read();
2990 /* FIXME: must restore OUR_EN ??? */
2991
2992 /* all cards provide GPIO info, some have an additional eeprom
2993 * LR50: GPIO coding can be found lower right CP1 .. CP9
2994 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
2995 * GPIO14-12: n.c.
2996 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
2997
2998 * lowest 3 bytes are remote control codes (no handshake needed)
2999 * xxxFFF: No remote control chip soldered
3000 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
3001 * Note: Some bits are Audio_Mask !
3002 */
3003 ttype = (gpio & 0x0f0000) >> 16;
3004 switch (ttype) {
3005 case 0x0:
3006 tuner_type = 2; /* NTSC, e.g. TPI8NSR11P */
3007 break;
3008 case 0x2:
3009 tuner_type = 39; /* LG NTSC (newer TAPC series) TAPC-H701P */
3010 break;
3011 case 0x4:
3012 tuner_type = 5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */
3013 break;
3014 case 0x6:
3015 tuner_type = 37; /* LG PAL (newer TAPC series) TAPC-G702P */
3016 break;
3017 case 0xC:
3018 tuner_type = 3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */
3019 break;
3020 default:
3021 pr_info("%d: FlyVideo_gpio: unknown tuner type\n", btv->c.nr);
3022 break;
3023 }
3024
3025 has_remote = gpio & 0x800000;
3026 has_radio = gpio & 0x400000;
3027 /* unknown 0x200000;
3028 * unknown2 0x100000; */
3029 is_capture_only = !(gpio & 0x008000); /* GPIO15 */
3030 has_tda9820_tda9821 = !(gpio & 0x004000);
3031 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */
3032 /*
3033 * gpio & 0x001000 output bit for audio routing */
3034
3035 if (is_capture_only)
3036 tuner_type = TUNER_ABSENT; /* No tuner present */
3037
3038 pr_info("%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
3039 btv->c.nr, has_radio ? "yes" : "no",
3040 has_remote ? "yes" : "no", tuner_type, gpio);
3041 pr_info("%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n",
3042 btv->c.nr, is_lr90 ? "yes" : "no",
3043 has_tda9820_tda9821 ? "yes" : "no",
3044 is_capture_only ? "yes" : "no");
3045
3046 if (tuner_type != UNSET) /* only set if known tuner autodetected, else let insmod option through */
3047 btv->tuner_type = tuner_type;
3048 btv->has_radio = has_radio;
3049
3050 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
3051 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
3052 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */
3053 if (has_tda9820_tda9821)
3054 btv->audio_mode_gpio = lt9415_audio;
3055 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */
3056 }
3057
3058 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1,
3059 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 };
3060 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1,
3061 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 };
3062
miro_pinnacle_gpio(struct bttv * btv)3063 static void miro_pinnacle_gpio(struct bttv *btv)
3064 {
3065 int id,msp,gpio;
3066 char *info;
3067
3068 gpio_inout(0xffffff, 0);
3069 gpio = gpio_read();
3070 id = ((gpio>>10) & 63) -1;
3071 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx");
3072 if (id < 32) {
3073 btv->tuner_type = miro_tunermap[id];
3074 if (0 == (gpio & 0x20)) {
3075 btv->has_radio = 1;
3076 if (!miro_fmtuner[id]) {
3077 btv->has_tea575x = 1;
3078 btv->tea_gpio.wren = 6;
3079 btv->tea_gpio.most = 7;
3080 btv->tea_gpio.clk = 8;
3081 btv->tea_gpio.data = 9;
3082 tea575x_init(btv);
3083 }
3084 } else {
3085 btv->has_radio = 0;
3086 }
3087 if (-1 != msp) {
3088 if (btv->c.type == BTTV_BOARD_MIRO)
3089 btv->c.type = BTTV_BOARD_MIROPRO;
3090 if (btv->c.type == BTTV_BOARD_PINNACLE)
3091 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3092 }
3093 pr_info("%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
3094 btv->c.nr, id+1, btv->tuner_type,
3095 !btv->has_radio ? "no" :
3096 (btv->has_tea575x ? "tea575x" : "fmtuner"),
3097 (-1 == msp) ? "no" : "yes");
3098 } else {
3099 /* new cards with microtune tuner */
3100 id = 63 - id;
3101 btv->has_radio = 0;
3102 switch (id) {
3103 case 1:
3104 info = "PAL / mono";
3105 btv->tda9887_conf = TDA9887_INTERCARRIER;
3106 break;
3107 case 2:
3108 info = "PAL+SECAM / stereo";
3109 btv->has_radio = 1;
3110 btv->tda9887_conf = TDA9887_QSS;
3111 break;
3112 case 3:
3113 info = "NTSC / stereo";
3114 btv->has_radio = 1;
3115 btv->tda9887_conf = TDA9887_QSS;
3116 break;
3117 case 4:
3118 info = "PAL+SECAM / mono";
3119 btv->tda9887_conf = TDA9887_QSS;
3120 break;
3121 case 5:
3122 info = "NTSC / mono";
3123 btv->tda9887_conf = TDA9887_INTERCARRIER;
3124 break;
3125 case 6:
3126 info = "NTSC / stereo";
3127 btv->tda9887_conf = TDA9887_INTERCARRIER;
3128 break;
3129 case 7:
3130 info = "PAL / stereo";
3131 btv->tda9887_conf = TDA9887_INTERCARRIER;
3132 break;
3133 default:
3134 info = "oops: unknown card";
3135 break;
3136 }
3137 if (-1 != msp)
3138 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3139 pr_info("%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
3140 btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
3141 btv->tuner_type = TUNER_MT2032;
3142 }
3143 }
3144
3145 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */
3146 #define LM1882_SYNC_DRIVE 0x200000L
3147
init_ids_eagle(struct bttv * btv)3148 static void init_ids_eagle(struct bttv *btv)
3149 {
3150 gpio_inout(0xffffff,0xFFFF37);
3151 gpio_write(0x200020);
3152
3153 /* flash strobe inverter ?! */
3154 gpio_write(0x200024);
3155
3156 /* switch sync drive off */
3157 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3158
3159 /* set BT848 muxel to 2 */
3160 btaor((2)<<5, ~(2<<5), BT848_IFORM);
3161 }
3162
3163 /* Muxsel helper for the IDS Eagle.
3164 * the eagles does not use the standard muxsel-bits but
3165 * has its own multiplexer */
eagle_muxsel(struct bttv * btv,unsigned int input)3166 static void eagle_muxsel(struct bttv *btv, unsigned int input)
3167 {
3168 gpio_bits(3, input & 3);
3169
3170 /* composite */
3171 /* set chroma ADC to sleep */
3172 btor(BT848_ADC_C_SLEEP, BT848_ADC);
3173 /* set to composite video */
3174 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
3175 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
3176
3177 /* switch sync drive off */
3178 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3179 }
3180
gvc1100_muxsel(struct bttv * btv,unsigned int input)3181 static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
3182 {
3183 static const int masks[] = {0x30, 0x01, 0x12, 0x23};
3184 gpio_write(masks[input%4]);
3185 }
3186
3187 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
3188 alarms output
3189
3190 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
3191 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | |
3192
3193 IN - sensor inputs, INx - sensor inputs and TI XORed together
3194 O1,O2,O3 - alarm outputs (relays)
3195
3196 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0
3197
3198 */
3199
init_lmlbt4x(struct bttv * btv)3200 static void init_lmlbt4x(struct bttv *btv)
3201 {
3202 pr_debug("LMLBT4x init\n");
3203 btwrite(0x000000, BT848_GPIO_REG_INP);
3204 gpio_inout(0xffffff, 0x0006C0);
3205 gpio_write(0x000000);
3206 }
3207
sigmaSQ_muxsel(struct bttv * btv,unsigned int input)3208 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
3209 {
3210 unsigned int inmux = input % 8;
3211 gpio_inout( 0xf, 0xf );
3212 gpio_bits( 0xf, inmux );
3213 }
3214
sigmaSLC_muxsel(struct bttv * btv,unsigned int input)3215 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
3216 {
3217 unsigned int inmux = input % 4;
3218 gpio_inout( 3<<9, 3<<9 );
3219 gpio_bits( 3<<9, inmux<<9 );
3220 }
3221
geovision_muxsel(struct bttv * btv,unsigned int input)3222 static void geovision_muxsel(struct bttv *btv, unsigned int input)
3223 {
3224 unsigned int inmux = input % 16;
3225 gpio_inout(0xf, 0xf);
3226 gpio_bits(0xf, inmux);
3227 }
3228
3229 /*
3230 * The TD3116 has 2 74HC4051 muxes wired to the MUX0 input of a bt878.
3231 * The first 74HC4051 has the lower 8 inputs, the second one the higher 8.
3232 * The muxes are controlled via a 74HC373 latch which is connected to
3233 * GPIOs 0-7. GPIO 18 is connected to the LE signal of the latch.
3234 * Q0 of the latch is connected to the Enable (~E) input of the first
3235 * 74HC4051. Q1 - Q3 are connected to S0 - S2 of the same 74HC4051.
3236 * Q4 - Q7 are connected to the second 74HC4051 in the same way.
3237 */
3238
td3116_latch_value(struct bttv * btv,u32 value)3239 static void td3116_latch_value(struct bttv *btv, u32 value)
3240 {
3241 gpio_bits((1<<18) | 0xff, value);
3242 gpio_bits((1<<18) | 0xff, (1<<18) | value);
3243 udelay(1);
3244 gpio_bits((1<<18) | 0xff, value);
3245 }
3246
td3116_muxsel(struct bttv * btv,unsigned int input)3247 static void td3116_muxsel(struct bttv *btv, unsigned int input)
3248 {
3249 u32 value;
3250 u32 highbit;
3251
3252 highbit = (input & 0x8) >> 3 ;
3253
3254 /* Disable outputs and set value in the mux */
3255 value = 0x11; /* Disable outputs */
3256 value |= ((input & 0x7) << 1) << (4 * highbit);
3257 td3116_latch_value(btv, value);
3258
3259 /* Enable the correct output */
3260 value &= ~0x11;
3261 value |= ((highbit ^ 0x1) << 4) | highbit;
3262 td3116_latch_value(btv, value);
3263 }
3264
3265 /* ----------------------------------------------------------------------- */
3266
bttv_reset_audio(struct bttv * btv)3267 static void bttv_reset_audio(struct bttv *btv)
3268 {
3269 /*
3270 * BT878A has a audio-reset register.
3271 * 1. This register is an audio reset function but it is in
3272 * function-0 (video capture) address space.
3273 * 2. It is enough to do this once per power-up of the card.
3274 * 3. There is a typo in the Conexant doc -- it is not at
3275 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
3276 * --//Shrikumar 030609
3277 */
3278 if (btv->id != 878)
3279 return;
3280
3281 if (bttv_debug)
3282 pr_debug("%d: BT878A ARESET\n", btv->c.nr);
3283 btwrite((1<<7), 0x058);
3284 udelay(10);
3285 btwrite( 0, 0x058);
3286 }
3287
3288 /* initialization part one -- before registering i2c bus */
bttv_init_card1(struct bttv * btv)3289 void bttv_init_card1(struct bttv *btv)
3290 {
3291 switch (btv->c.type) {
3292 case BTTV_BOARD_HAUPPAUGE:
3293 case BTTV_BOARD_HAUPPAUGE878:
3294 boot_msp34xx(btv,5);
3295 break;
3296 case BTTV_BOARD_VOODOOTV_200:
3297 case BTTV_BOARD_VOODOOTV_FM:
3298 boot_msp34xx(btv,20);
3299 break;
3300 case BTTV_BOARD_AVERMEDIA98:
3301 boot_msp34xx(btv,11);
3302 break;
3303 case BTTV_BOARD_HAUPPAUGEPVR:
3304 pvr_boot(btv);
3305 break;
3306 case BTTV_BOARD_TWINHAN_DST:
3307 case BTTV_BOARD_AVDVBT_771:
3308 case BTTV_BOARD_PINNACLESAT:
3309 btv->use_i2c_hw = 1;
3310 break;
3311 case BTTV_BOARD_ADLINK_RTV24:
3312 init_RTV24( btv );
3313 break;
3314 case BTTV_BOARD_PCI_8604PW:
3315 init_PCI8604PW(btv);
3316 break;
3317
3318 }
3319 if (!bttv_tvcards[btv->c.type].has_dvb)
3320 bttv_reset_audio(btv);
3321 }
3322
3323 /* initialization part two -- after registering i2c bus */
bttv_init_card2(struct bttv * btv)3324 void bttv_init_card2(struct bttv *btv)
3325 {
3326 btv->tuner_type = UNSET;
3327
3328 if (BTTV_BOARD_UNKNOWN == btv->c.type) {
3329 bttv_readee(btv,eeprom_data,0xa0);
3330 identify_by_eeprom(btv,eeprom_data);
3331 }
3332
3333 switch (btv->c.type) {
3334 case BTTV_BOARD_MIRO:
3335 case BTTV_BOARD_MIROPRO:
3336 case BTTV_BOARD_PINNACLE:
3337 case BTTV_BOARD_PINNACLEPRO:
3338 /* miro/pinnacle */
3339 miro_pinnacle_gpio(btv);
3340 break;
3341 case BTTV_BOARD_FLYVIDEO_98:
3342 case BTTV_BOARD_MAXI:
3343 case BTTV_BOARD_LIFE_FLYKIT:
3344 case BTTV_BOARD_FLYVIDEO:
3345 case BTTV_BOARD_TYPHOON_TVIEW:
3346 case BTTV_BOARD_CHRONOS_VS2:
3347 case BTTV_BOARD_FLYVIDEO_98FM:
3348 case BTTV_BOARD_FLYVIDEO2000:
3349 case BTTV_BOARD_FLYVIDEO98EZ:
3350 case BTTV_BOARD_CONFERENCETV:
3351 case BTTV_BOARD_LIFETEC_9415:
3352 flyvideo_gpio(btv);
3353 break;
3354 case BTTV_BOARD_HAUPPAUGE:
3355 case BTTV_BOARD_HAUPPAUGE878:
3356 case BTTV_BOARD_HAUPPAUGEPVR:
3357 /* pick up some config infos from the eeprom */
3358 bttv_readee(btv,eeprom_data,0xa0);
3359 hauppauge_eeprom(btv);
3360 break;
3361 case BTTV_BOARD_AVERMEDIA98:
3362 case BTTV_BOARD_AVPHONE98:
3363 bttv_readee(btv,eeprom_data,0xa0);
3364 avermedia_eeprom(btv);
3365 break;
3366 case BTTV_BOARD_PXC200:
3367 init_PXC200(btv);
3368 break;
3369 case BTTV_BOARD_PICOLO_TETRA_CHIP:
3370 picolo_tetra_init(btv);
3371 break;
3372 case BTTV_BOARD_VHX:
3373 btv->has_radio = 1;
3374 btv->has_tea575x = 1;
3375 btv->tea_gpio.wren = 5;
3376 btv->tea_gpio.most = 6;
3377 btv->tea_gpio.clk = 3;
3378 btv->tea_gpio.data = 4;
3379 tea575x_init(btv);
3380 break;
3381 case BTTV_BOARD_VOBIS_BOOSTAR:
3382 case BTTV_BOARD_TERRATV:
3383 terratec_active_radio_upgrade(btv);
3384 break;
3385 case BTTV_BOARD_MAGICTVIEW061:
3386 if (btv->cardid == 0x3002144f) {
3387 btv->has_radio=1;
3388 pr_info("%d: radio detected by subsystem id (CPH05x)\n",
3389 btv->c.nr);
3390 }
3391 break;
3392 case BTTV_BOARD_STB2:
3393 if (btv->cardid == 0x3060121a) {
3394 /* Fix up entry for 3DFX VoodooTV 100,
3395 which is an OEM STB card variant. */
3396 btv->has_radio=0;
3397 btv->tuner_type=TUNER_TEMIC_NTSC;
3398 }
3399 break;
3400 case BTTV_BOARD_OSPREY1x0:
3401 case BTTV_BOARD_OSPREY1x0_848:
3402 case BTTV_BOARD_OSPREY101_848:
3403 case BTTV_BOARD_OSPREY1x1:
3404 case BTTV_BOARD_OSPREY1x1_SVID:
3405 case BTTV_BOARD_OSPREY2xx:
3406 case BTTV_BOARD_OSPREY2x0_SVID:
3407 case BTTV_BOARD_OSPREY2x0:
3408 case BTTV_BOARD_OSPREY440:
3409 case BTTV_BOARD_OSPREY500:
3410 case BTTV_BOARD_OSPREY540:
3411 case BTTV_BOARD_OSPREY2000:
3412 bttv_readee(btv,eeprom_data,0xa0);
3413 osprey_eeprom(btv, eeprom_data);
3414 break;
3415 case BTTV_BOARD_IDS_EAGLE:
3416 init_ids_eagle(btv);
3417 break;
3418 case BTTV_BOARD_MODTEC_205:
3419 bttv_readee(btv,eeprom_data,0xa0);
3420 modtec_eeprom(btv);
3421 break;
3422 case BTTV_BOARD_LMLBT4:
3423 init_lmlbt4x(btv);
3424 break;
3425 case BTTV_BOARD_TIBET_CS16:
3426 tibetCS16_init(btv);
3427 break;
3428 case BTTV_BOARD_KODICOM_4400R:
3429 kodicom4400r_init(btv);
3430 break;
3431 case BTTV_BOARD_GEOVISION_GV800S:
3432 gv800s_init(btv);
3433 break;
3434 }
3435
3436 /* pll configuration */
3437 if (!(btv->id==848 && btv->revision==0x11)) {
3438 /* defaults from card list */
3439 if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
3440 btv->pll.pll_ifreq=28636363;
3441 btv->pll.pll_crystal=BT848_IFORM_XT0;
3442 }
3443 if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
3444 btv->pll.pll_ifreq=35468950;
3445 btv->pll.pll_crystal=BT848_IFORM_XT1;
3446 }
3447 if (PLL_14 == bttv_tvcards[btv->c.type].pll) {
3448 btv->pll.pll_ifreq = 14318181;
3449 btv->pll.pll_crystal = BT848_IFORM_XT0;
3450 }
3451 /* insmod options can override */
3452 switch (pll[btv->c.nr]) {
3453 case 0: /* none */
3454 btv->pll.pll_crystal = 0;
3455 btv->pll.pll_ifreq = 0;
3456 btv->pll.pll_ofreq = 0;
3457 break;
3458 case 1: /* 28 MHz */
3459 case 28:
3460 btv->pll.pll_ifreq = 28636363;
3461 btv->pll.pll_ofreq = 0;
3462 btv->pll.pll_crystal = BT848_IFORM_XT0;
3463 break;
3464 case 2: /* 35 MHz */
3465 case 35:
3466 btv->pll.pll_ifreq = 35468950;
3467 btv->pll.pll_ofreq = 0;
3468 btv->pll.pll_crystal = BT848_IFORM_XT1;
3469 break;
3470 case 3: /* 14 MHz */
3471 case 14:
3472 btv->pll.pll_ifreq = 14318181;
3473 btv->pll.pll_ofreq = 0;
3474 btv->pll.pll_crystal = BT848_IFORM_XT0;
3475 break;
3476 }
3477 }
3478 btv->pll.pll_current = -1;
3479
3480 /* tuner configuration (from card list / autodetect / insmod option) */
3481 if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
3482 if (UNSET == btv->tuner_type)
3483 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
3484 if (UNSET != tuner[btv->c.nr])
3485 btv->tuner_type = tuner[btv->c.nr];
3486
3487 if (btv->tuner_type == TUNER_ABSENT)
3488 pr_info("%d: tuner absent\n", btv->c.nr);
3489 else if (btv->tuner_type == UNSET)
3490 pr_warn("%d: tuner type unset\n", btv->c.nr);
3491 else
3492 pr_info("%d: tuner type=%d\n", btv->c.nr, btv->tuner_type);
3493
3494 if (autoload != UNSET) {
3495 pr_warn("%d: the autoload option is obsolete\n", btv->c.nr);
3496 pr_warn("%d: use option msp3400, tda7432 or tvaudio to override which audio module should be used\n",
3497 btv->c.nr);
3498 }
3499
3500 if (UNSET == btv->tuner_type)
3501 btv->tuner_type = TUNER_ABSENT;
3502
3503 btv->dig = bttv_tvcards[btv->c.type].has_dig_in ?
3504 bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET;
3505 btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ?
3506 UNSET : bttv_tvcards[btv->c.type].svhs;
3507 if (svhs[btv->c.nr] != UNSET)
3508 btv->svhs = svhs[btv->c.nr];
3509 if (remote[btv->c.nr] != UNSET)
3510 btv->has_remote = remote[btv->c.nr];
3511
3512 if (bttv_tvcards[btv->c.type].has_radio)
3513 btv->has_radio = 1;
3514 if (bttv_tvcards[btv->c.type].has_remote)
3515 btv->has_remote = 1;
3516 if (!bttv_tvcards[btv->c.type].no_gpioirq)
3517 btv->gpioirq = 1;
3518 if (bttv_tvcards[btv->c.type].volume_gpio)
3519 btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio;
3520 if (bttv_tvcards[btv->c.type].audio_mode_gpio)
3521 btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio;
3522
3523 if (btv->tuner_type == TUNER_ABSENT)
3524 return; /* no tuner or related drivers to load */
3525
3526 if (btv->has_saa6588 || saa6588[btv->c.nr]) {
3527 /* Probe for RDS receiver chip */
3528 static const unsigned short addrs[] = {
3529 0x20 >> 1,
3530 0x22 >> 1,
3531 I2C_CLIENT_END
3532 };
3533 struct v4l2_subdev *sd;
3534
3535 sd = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3536 &btv->c.i2c_adap, "saa6588", 0, addrs);
3537 btv->has_saa6588 = (sd != NULL);
3538 }
3539
3540 /* try to detect audio/fader chips */
3541
3542 /* First check if the user specified the audio chip via a module
3543 option. */
3544
3545 switch (audiodev[btv->c.nr]) {
3546 case -1:
3547 return; /* do not load any audio module */
3548
3549 case 0: /* autodetect */
3550 break;
3551
3552 case 1: {
3553 /* The user specified that we should probe for msp3400 */
3554 static const unsigned short addrs[] = {
3555 I2C_ADDR_MSP3400 >> 1,
3556 I2C_ADDR_MSP3400_ALT >> 1,
3557 I2C_CLIENT_END
3558 };
3559
3560 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3561 &btv->c.i2c_adap, "msp3400", 0, addrs);
3562 if (btv->sd_msp34xx)
3563 return;
3564 goto no_audio;
3565 }
3566
3567 case 2: {
3568 /* The user specified that we should probe for tda7432 */
3569 static const unsigned short addrs[] = {
3570 I2C_ADDR_TDA7432 >> 1,
3571 I2C_CLIENT_END
3572 };
3573
3574 if (v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3575 &btv->c.i2c_adap, "tda7432", 0, addrs))
3576 return;
3577 goto no_audio;
3578 }
3579
3580 case 3: {
3581 /* The user specified that we should probe for tvaudio */
3582 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3583 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3584 if (btv->sd_tvaudio)
3585 return;
3586 goto no_audio;
3587 }
3588
3589 default:
3590 pr_warn("%d: unknown audiodev value!\n", btv->c.nr);
3591 return;
3592 }
3593
3594 /* There were no overrides, so now we try to discover this through the
3595 card definition */
3596
3597 /* probe for msp3400 first: this driver can detect whether or not
3598 it really is a msp3400, so it will return NULL when the device
3599 found is really something else (e.g. a tea6300). */
3600 if (!bttv_tvcards[btv->c.type].no_msp34xx) {
3601 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3602 &btv->c.i2c_adap, "msp3400",
3603 0, I2C_ADDRS(I2C_ADDR_MSP3400 >> 1));
3604 } else if (bttv_tvcards[btv->c.type].msp34xx_alt) {
3605 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3606 &btv->c.i2c_adap, "msp3400",
3607 0, I2C_ADDRS(I2C_ADDR_MSP3400_ALT >> 1));
3608 }
3609
3610 /* If we found a msp34xx, then we're done. */
3611 if (btv->sd_msp34xx)
3612 return;
3613
3614 /* Now see if we can find one of the tvaudio devices. */
3615 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3616 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3617 if (btv->sd_tvaudio) {
3618 /* There may be two tvaudio chips on the card, so try to
3619 find another. */
3620 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3621 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3622 }
3623
3624 /* it might also be a tda7432. */
3625 if (!bttv_tvcards[btv->c.type].no_tda7432) {
3626 static const unsigned short addrs[] = {
3627 I2C_ADDR_TDA7432 >> 1,
3628 I2C_CLIENT_END
3629 };
3630
3631 btv->sd_tda7432 = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3632 &btv->c.i2c_adap, "tda7432", 0, addrs);
3633 if (btv->sd_tda7432)
3634 return;
3635 }
3636 if (btv->sd_tvaudio)
3637 return;
3638
3639 no_audio:
3640 pr_warn("%d: audio absent, no audio device found!\n", btv->c.nr);
3641 }
3642
3643
3644 /* initialize the tuner */
bttv_init_tuner(struct bttv * btv)3645 void bttv_init_tuner(struct bttv *btv)
3646 {
3647 int addr = ADDR_UNSET;
3648
3649 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr)
3650 addr = bttv_tvcards[btv->c.type].tuner_addr;
3651
3652 if (btv->tuner_type != TUNER_ABSENT) {
3653 struct tuner_setup tun_setup;
3654
3655 /* Load tuner module before issuing tuner config call! */
3656 if (btv->has_radio)
3657 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3658 &btv->c.i2c_adap, "tuner",
3659 0, v4l2_i2c_tuner_addrs(ADDRS_RADIO));
3660 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3661 &btv->c.i2c_adap, "tuner",
3662 0, v4l2_i2c_tuner_addrs(ADDRS_DEMOD));
3663 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3664 &btv->c.i2c_adap, "tuner",
3665 0, v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD));
3666
3667 tun_setup.mode_mask = T_ANALOG_TV;
3668 tun_setup.type = btv->tuner_type;
3669 tun_setup.addr = addr;
3670
3671 if (btv->has_radio)
3672 tun_setup.mode_mask |= T_RADIO;
3673
3674 bttv_call_all(btv, tuner, s_type_addr, &tun_setup);
3675 }
3676
3677 if (btv->tda9887_conf) {
3678 struct v4l2_priv_tun_config tda9887_cfg;
3679
3680 tda9887_cfg.tuner = TUNER_TDA9887;
3681 tda9887_cfg.priv = &btv->tda9887_conf;
3682
3683 bttv_call_all(btv, tuner, s_config, &tda9887_cfg);
3684 }
3685 }
3686
3687 /* ----------------------------------------------------------------------- */
3688
modtec_eeprom(struct bttv * btv)3689 static void modtec_eeprom(struct bttv *btv)
3690 {
3691 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
3692 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
3693 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3694 btv->c.nr, &eeprom_data[0x1e]);
3695 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
3696 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
3697 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3698 btv->c.nr, &eeprom_data[0x1e]);
3699 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
3700 btv->tuner_type=TUNER_PHILIPS_NTSC;
3701 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3702 btv->c.nr, &eeprom_data[0x1e]);
3703 } else {
3704 pr_info("%d: Modtec: Unknown TunerString: %s\n",
3705 btv->c.nr, &eeprom_data[0x1e]);
3706 }
3707 }
3708
hauppauge_eeprom(struct bttv * btv)3709 static void hauppauge_eeprom(struct bttv *btv)
3710 {
3711 struct tveeprom tv;
3712
3713 tveeprom_hauppauge_analog(&tv, eeprom_data);
3714 btv->tuner_type = tv.tuner_type;
3715 btv->has_radio = tv.has_radio;
3716
3717 pr_info("%d: Hauppauge eeprom indicates model#%d\n",
3718 btv->c.nr, tv.model);
3719
3720 /*
3721 * Some of the 878 boards have duplicate PCI IDs. Switch the board
3722 * type based on model #.
3723 */
3724 if(tv.model == 64900) {
3725 pr_info("%d: Switching board type from %s to %s\n",
3726 btv->c.nr,
3727 bttv_tvcards[btv->c.type].name,
3728 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name);
3729 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB;
3730 }
3731
3732 /* The 61334 needs the msp3410 to do the radio demod to get sound */
3733 if (tv.model == 61334)
3734 btv->radio_uses_msp_demodulator = 1;
3735 }
3736
3737 /* ----------------------------------------------------------------------- */
3738
bttv_tea575x_set_pins(struct snd_tea575x * tea,u8 pins)3739 static void bttv_tea575x_set_pins(struct snd_tea575x *tea, u8 pins)
3740 {
3741 struct bttv *btv = tea->private_data;
3742 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3743 u16 val = 0;
3744
3745 val |= (pins & TEA575X_DATA) ? (1 << gpio.data) : 0;
3746 val |= (pins & TEA575X_CLK) ? (1 << gpio.clk) : 0;
3747 val |= (pins & TEA575X_WREN) ? (1 << gpio.wren) : 0;
3748
3749 gpio_bits((1 << gpio.data) | (1 << gpio.clk) | (1 << gpio.wren), val);
3750 if (btv->mbox_ior) {
3751 /* IOW and CSEL active */
3752 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
3753 udelay(5);
3754 /* all inactive */
3755 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3756 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3757 }
3758 }
3759
bttv_tea575x_get_pins(struct snd_tea575x * tea)3760 static u8 bttv_tea575x_get_pins(struct snd_tea575x *tea)
3761 {
3762 struct bttv *btv = tea->private_data;
3763 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3764 u8 ret = 0;
3765 u16 val;
3766
3767 if (btv->mbox_ior) {
3768 /* IOR and CSEL active */
3769 gpio_bits(btv->mbox_ior | btv->mbox_csel, 0);
3770 udelay(5);
3771 }
3772 val = gpio_read();
3773 if (btv->mbox_ior) {
3774 /* all inactive */
3775 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3776 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3777 }
3778
3779 if (val & (1 << gpio.data))
3780 ret |= TEA575X_DATA;
3781 if (val & (1 << gpio.most))
3782 ret |= TEA575X_MOST;
3783
3784 return ret;
3785 }
3786
bttv_tea575x_set_direction(struct snd_tea575x * tea,bool output)3787 static void bttv_tea575x_set_direction(struct snd_tea575x *tea, bool output)
3788 {
3789 struct bttv *btv = tea->private_data;
3790 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3791 u32 mask = (1 << gpio.clk) | (1 << gpio.wren) | (1 << gpio.data) |
3792 (1 << gpio.most);
3793
3794 if (output)
3795 gpio_inout(mask, (1 << gpio.data) | (1 << gpio.clk) |
3796 (1 << gpio.wren));
3797 else
3798 gpio_inout(mask, (1 << gpio.clk) | (1 << gpio.wren));
3799 }
3800
3801 static const struct snd_tea575x_ops bttv_tea_ops = {
3802 .set_pins = bttv_tea575x_set_pins,
3803 .get_pins = bttv_tea575x_get_pins,
3804 .set_direction = bttv_tea575x_set_direction,
3805 };
3806
tea575x_init(struct bttv * btv)3807 static int tea575x_init(struct bttv *btv)
3808 {
3809 btv->tea.private_data = btv;
3810 btv->tea.ops = &bttv_tea_ops;
3811 if (!snd_tea575x_hw_init(&btv->tea)) {
3812 pr_info("%d: detected TEA575x radio\n", btv->c.nr);
3813 btv->tea.mute = false;
3814 return 0;
3815 }
3816
3817 btv->has_tea575x = 0;
3818 btv->has_radio = 0;
3819
3820 return -ENODEV;
3821 }
3822
3823 /* ----------------------------------------------------------------------- */
3824
terratec_active_radio_upgrade(struct bttv * btv)3825 static int terratec_active_radio_upgrade(struct bttv *btv)
3826 {
3827 btv->has_radio = 1;
3828 btv->has_tea575x = 1;
3829 btv->tea_gpio.wren = 4;
3830 btv->tea_gpio.most = 5;
3831 btv->tea_gpio.clk = 3;
3832 btv->tea_gpio.data = 2;
3833
3834 btv->mbox_iow = 1 << 8;
3835 btv->mbox_ior = 1 << 9;
3836 btv->mbox_csel = 1 << 10;
3837
3838 if (!tea575x_init(btv)) {
3839 pr_info("%d: Terratec Active Radio Upgrade found\n", btv->c.nr);
3840 btv->has_saa6588 = 1;
3841 }
3842
3843 return 0;
3844 }
3845
3846
3847 /* ----------------------------------------------------------------------- */
3848
3849 /*
3850 * minimal bootstrap for the WinTV/PVR -- upload altera firmware.
3851 *
3852 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have
3853 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
3854 * unpacked with unzip).
3855 */
3856 #define PVR_GPIO_DELAY 10
3857
3858 #define BTTV_ALT_DATA 0x000001
3859 #define BTTV_ALT_DCLK 0x100000
3860 #define BTTV_ALT_NCONFIG 0x800000
3861
pvr_altera_load(struct bttv * btv,const u8 * micro,u32 microlen)3862 static int pvr_altera_load(struct bttv *btv, const u8 *micro, u32 microlen)
3863 {
3864 u32 n;
3865 u8 bits;
3866 int i;
3867
3868 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
3869 gpio_write(0);
3870 udelay(PVR_GPIO_DELAY);
3871
3872 gpio_write(BTTV_ALT_NCONFIG);
3873 udelay(PVR_GPIO_DELAY);
3874
3875 for (n = 0; n < microlen; n++) {
3876 bits = micro[n];
3877 for (i = 0 ; i < 8 ; i++) {
3878 gpio_bits(BTTV_ALT_DCLK,0);
3879 if (bits & 0x01)
3880 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
3881 else
3882 gpio_bits(BTTV_ALT_DATA,0);
3883 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3884 bits >>= 1;
3885 }
3886 }
3887 gpio_bits(BTTV_ALT_DCLK,0);
3888 udelay(PVR_GPIO_DELAY);
3889
3890 /* begin Altera init loop (Not necessary,but doesn't hurt) */
3891 for (i = 0 ; i < 30 ; i++) {
3892 gpio_bits(BTTV_ALT_DCLK,0);
3893 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3894 }
3895 gpio_bits(BTTV_ALT_DCLK,0);
3896 return 0;
3897 }
3898
pvr_boot(struct bttv * btv)3899 static int pvr_boot(struct bttv *btv)
3900 {
3901 const struct firmware *fw_entry;
3902 int rc;
3903
3904 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
3905 if (rc != 0) {
3906 pr_warn("%d: no altera firmware [via hotplug]\n", btv->c.nr);
3907 return rc;
3908 }
3909 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
3910 pr_info("%d: altera firmware upload %s\n",
3911 btv->c.nr, (rc < 0) ? "failed" : "ok");
3912 release_firmware(fw_entry);
3913 return rc;
3914 }
3915
3916 /* ----------------------------------------------------------------------- */
3917 /* some osprey specific stuff */
3918
osprey_eeprom(struct bttv * btv,const u8 ee[256])3919 static void osprey_eeprom(struct bttv *btv, const u8 ee[256])
3920 {
3921 int i;
3922 u32 serial = 0;
3923 int cardid = -1;
3924
3925 /* This code will never actually get called in this case.... */
3926 if (btv->c.type == BTTV_BOARD_UNKNOWN) {
3927 /* this might be an antique... check for MMAC label in eeprom */
3928 if (!strncmp(ee, "MMAC", 4)) {
3929 u8 checksum = 0;
3930 for (i = 0; i < 21; i++)
3931 checksum += ee[i];
3932 if (checksum != ee[21])
3933 return;
3934 cardid = BTTV_BOARD_OSPREY1x0_848;
3935 for (i = 12; i < 21; i++) {
3936 serial *= 10;
3937 serial += ee[i] - '0';
3938 }
3939 }
3940 } else {
3941 unsigned short type;
3942
3943 for (i = 4 * 16; i < 8 * 16; i += 16) {
3944 u16 checksum = (__force u16)ip_compute_csum(ee + i, 16);
3945
3946 if ((checksum & 0xff) + (checksum >> 8) == 0xff)
3947 break;
3948 }
3949 if (i >= 8*16)
3950 return;
3951 ee += i;
3952
3953 /* found a valid descriptor */
3954 type = get_unaligned_be16((__be16 *)(ee+4));
3955
3956 switch(type) {
3957 /* 848 based */
3958 case 0x0004:
3959 cardid = BTTV_BOARD_OSPREY1x0_848;
3960 break;
3961 case 0x0005:
3962 cardid = BTTV_BOARD_OSPREY101_848;
3963 break;
3964
3965 /* 878 based */
3966 case 0x0012:
3967 case 0x0013:
3968 cardid = BTTV_BOARD_OSPREY1x0;
3969 break;
3970 case 0x0014:
3971 case 0x0015:
3972 cardid = BTTV_BOARD_OSPREY1x1;
3973 break;
3974 case 0x0016:
3975 case 0x0017:
3976 case 0x0020:
3977 cardid = BTTV_BOARD_OSPREY1x1_SVID;
3978 break;
3979 case 0x0018:
3980 case 0x0019:
3981 case 0x001E:
3982 case 0x001F:
3983 cardid = BTTV_BOARD_OSPREY2xx;
3984 break;
3985 case 0x001A:
3986 case 0x001B:
3987 cardid = BTTV_BOARD_OSPREY2x0_SVID;
3988 break;
3989 case 0x0040:
3990 cardid = BTTV_BOARD_OSPREY500;
3991 break;
3992 case 0x0050:
3993 case 0x0056:
3994 cardid = BTTV_BOARD_OSPREY540;
3995 /* bttv_osprey_540_init(btv); */
3996 break;
3997 case 0x0060:
3998 case 0x0070:
3999 case 0x00A0:
4000 cardid = BTTV_BOARD_OSPREY2x0;
4001 /* enable output on select control lines */
4002 gpio_inout(0xffffff,0x000303);
4003 break;
4004 case 0x00D8:
4005 cardid = BTTV_BOARD_OSPREY440;
4006 break;
4007 default:
4008 /* unknown...leave generic, but get serial # */
4009 pr_info("%d: osprey eeprom: unknown card type 0x%04x\n",
4010 btv->c.nr, type);
4011 break;
4012 }
4013 serial = get_unaligned_be32((__be32 *)(ee+6));
4014 }
4015
4016 pr_info("%d: osprey eeprom: card=%d '%s' serial=%u\n",
4017 btv->c.nr, cardid,
4018 cardid > 0 ? bttv_tvcards[cardid].name : "Unknown", serial);
4019
4020 if (cardid<0 || btv->c.type == cardid)
4021 return;
4022
4023 /* card type isn't set correctly */
4024 if (card[btv->c.nr] < bttv_num_tvcards) {
4025 pr_warn("%d: osprey eeprom: Not overriding user specified card type\n",
4026 btv->c.nr);
4027 } else {
4028 pr_info("%d: osprey eeprom: Changing card type from %d to %d\n",
4029 btv->c.nr, btv->c.type, cardid);
4030 btv->c.type = cardid;
4031 }
4032 }
4033
4034 /* ----------------------------------------------------------------------- */
4035 /* AVermedia specific stuff, from bktr_card.c */
4036
4037 static int tuner_0_table[] = {
4038 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/,
4039 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/,
4040 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL,
4041 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
4042 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
4043 TUNER_PHILIPS_FM1216ME_MK3 };
4044
4045 static int tuner_1_table[] = {
4046 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL,
4047 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
4048 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
4049 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */
4050 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
4051
avermedia_eeprom(struct bttv * btv)4052 static void avermedia_eeprom(struct bttv *btv)
4053 {
4054 int tuner_make, tuner_tv_fm, tuner_format, tuner_type = 0;
4055
4056 tuner_make = (eeprom_data[0x41] & 0x7);
4057 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3;
4058 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4;
4059 btv->has_remote = (eeprom_data[0x42] & 0x01);
4060
4061 if (tuner_make == 0 || tuner_make == 2)
4062 if (tuner_format <= 0x0a)
4063 tuner_type = tuner_0_table[tuner_format];
4064 if (tuner_make == 1)
4065 if (tuner_format <= 9)
4066 tuner_type = tuner_1_table[tuner_format];
4067
4068 if (tuner_make == 4)
4069 if (tuner_format == 0x09)
4070 tuner_type = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */
4071
4072 pr_info("%d: Avermedia eeprom[0x%02x%02x]: tuner=",
4073 btv->c.nr, eeprom_data[0x41], eeprom_data[0x42]);
4074 if (tuner_type) {
4075 btv->tuner_type = tuner_type;
4076 pr_cont("%d", tuner_type);
4077 } else
4078 pr_cont("Unknown type");
4079 pr_cont(" radio:%s remote control:%s\n",
4080 tuner_tv_fm ? "yes" : "no",
4081 btv->has_remote ? "yes" : "no");
4082 }
4083
4084 /*
4085 * For Voodoo TV/FM and Voodoo 200. These cards' tuners use a TDA9880
4086 * analog demod, which is not I2C controlled like the newer and more common
4087 * TDA9887 series. Instead it has two tri-state input pins, S0 and S1,
4088 * that control the IF for the video and audio. Apparently, bttv GPIO
4089 * 0x10000 is connected to S0. S0 low selects a 38.9 MHz VIF for B/G/D/K/I
4090 * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC).
4091 */
bttv_tda9880_setnorm(struct bttv * btv,u32 gpiobits)4092 u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits)
4093 {
4094
4095 if (btv->audio_input == TVAUDIO_INPUT_TUNER) {
4096 if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN)
4097 gpiobits |= 0x10000;
4098 else
4099 gpiobits &= ~0x10000;
4100 }
4101
4102 gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits);
4103 return gpiobits;
4104 }
4105
4106
4107 /*
4108 * reset/enable the MSP on some Hauppauge cards
4109 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)!
4110 *
4111 * Hauppauge: pin 5
4112 * Voodoo: pin 20
4113 */
boot_msp34xx(struct bttv * btv,int pin)4114 static void boot_msp34xx(struct bttv *btv, int pin)
4115 {
4116 int mask = (1 << pin);
4117
4118 gpio_inout(mask,mask);
4119 gpio_bits(mask,0);
4120 mdelay(2);
4121 udelay(500);
4122 gpio_bits(mask,mask);
4123
4124 if (bttv_gpio)
4125 bttv_gpio_tracking(btv,"msp34xx");
4126 if (bttv_verbose)
4127 pr_info("%d: Hauppauge/Voodoo msp34xx: reset line init [%d]\n",
4128 btv->c.nr, pin);
4129 }
4130
4131 /* ----------------------------------------------------------------------- */
4132 /* Imagenation L-Model PXC200 Framegrabber */
4133 /* This is basically the same procedure as
4134 * used by Alessandro Rubini in his pxc200
4135 * driver, but using BTTV functions */
4136
init_PXC200(struct bttv * btv)4137 static void init_PXC200(struct bttv *btv)
4138 {
4139 static int vals[] = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d, 0x01, 0x02,
4140 0x03, 0x04, 0x05, 0x06, 0x00 };
4141 unsigned int i;
4142 int tmp;
4143 u32 val;
4144
4145 /* Initialise GPIO-connected stuff */
4146 gpio_inout(0xffffff, (1<<13));
4147 gpio_write(0);
4148 udelay(3);
4149 gpio_write(1<<13);
4150 /* GPIO inputs are pulled up, so no need to drive
4151 * reset pin any longer */
4152 gpio_bits(0xffffff, 0);
4153 if (bttv_gpio)
4154 bttv_gpio_tracking(btv,"pxc200");
4155
4156 /* we could/should try and reset/control the AD pots? but
4157 right now we simply turned off the crushing. Without
4158 this the AGC drifts drifts
4159 remember the EN is reverse logic -->
4160 setting BT848_ADC_AGC_EN disable the AGC
4161 tboult@eecs.lehigh.edu
4162 */
4163
4164 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
4165
4166 /* Initialise MAX517 DAC */
4167 pr_info("Setting DAC reference voltage level ...\n");
4168 bttv_I2CWrite(btv,0x5E,0,0x80,1);
4169
4170 /* Initialise 12C508 PIC */
4171 /* The I2CWrite and I2CRead commands are actually to the
4172 * same chips - but the R/W bit is included in the address
4173 * argument so the numbers are different */
4174
4175
4176 pr_info("Initialising 12C508 PIC chip ...\n");
4177
4178 /* First of all, enable the clock line. This is used in the PXC200-F */
4179 val = btread(BT848_GPIO_DMA_CTL);
4180 val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
4181 btwrite(val, BT848_GPIO_DMA_CTL);
4182
4183 /* Then, push to 0 the reset pin long enough to reset the *
4184 * device same as above for the reset line, but not the same
4185 * value sent to the GPIO-connected stuff
4186 * which one is the good one? */
4187 gpio_inout(0xffffff,(1<<2));
4188 gpio_write(0);
4189 udelay(10);
4190 gpio_write(1<<2);
4191
4192 for (i = 0; i < ARRAY_SIZE(vals); i++) {
4193 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
4194 if (tmp != -1) {
4195 pr_info("I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
4196 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
4197 }
4198 }
4199
4200 pr_info("PXC200 Initialised\n");
4201 }
4202
4203
4204
4205 /* ----------------------------------------------------------------------- */
4206 /*
4207 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
4208 * it. This apparently involves the following procedure for each 878 chip:
4209 *
4210 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register
4211 *
4212 * 2) write to GPIO_DATA
4213 * - 0x0E
4214 * - sleep 1ms
4215 * - 0x10 + 0x0E
4216 * - sleep 10ms
4217 * - 0x0E
4218 * read from GPIO_DATA into buf (uint_32)
4219 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
4220 * error. ERROR_CPLD_Check_Failed stop.
4221 *
4222 * 3) write to GPIO_DATA
4223 * - write 0x4400 + 0x0E
4224 * - sleep 10ms
4225 * - write 0x4410 + 0x0E
4226 * - sleep 1ms
4227 * - write 0x0E
4228 * read from GPIO_DATA into buf (uint_32)
4229 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 )
4230 * error. ERROR_CPLD_Check_Failed.
4231 */
4232 /* ----------------------------------------------------------------------- */
4233 static void
init_RTV24(struct bttv * btv)4234 init_RTV24 (struct bttv *btv)
4235 {
4236 uint32_t dataRead = 0;
4237 long watchdog_value = 0x0E;
4238
4239 pr_info("%d: Adlink RTV-24 initialisation in progress ...\n",
4240 btv->c.nr);
4241
4242 btwrite (0x00c3feff, BT848_GPIO_OUT_EN);
4243
4244 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4245 msleep (1);
4246 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA);
4247 msleep (10);
4248 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4249
4250 dataRead = btread (BT848_GPIO_DATA);
4251
4252 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) {
4253 pr_info("%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n",
4254 btv->c.nr, dataRead);
4255 }
4256
4257 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA);
4258 msleep (10);
4259 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA);
4260 msleep (1);
4261 btwrite (watchdog_value, BT848_GPIO_DATA);
4262 msleep (1);
4263 dataRead = btread (BT848_GPIO_DATA);
4264
4265 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) {
4266 pr_info("%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n",
4267 btv->c.nr, dataRead);
4268
4269 return;
4270 }
4271
4272 pr_info("%d: Adlink RTV-24 initialisation complete\n", btv->c.nr);
4273 }
4274
4275
4276
4277 /* ----------------------------------------------------------------------- */
4278 /*
4279 * The PCI-8604PW contains a CPLD, probably an ispMACH 4A, that filters
4280 * the PCI REQ signals coming from the four BT878 chips. After power
4281 * up, the CPLD does not forward requests to the bus, which prevents
4282 * the BT878 from fetching RISC instructions from memory. While the
4283 * CPLD is connected to most of the GPIOs of PCI device 0xD, only
4284 * five appear to play a role in unlocking the REQ signal. The following
4285 * sequence has been determined by trial and error without access to the
4286 * original driver.
4287 *
4288 * Eight GPIOs of device 0xC are provided on connector CN4 (4 in, 4 out).
4289 * Devices 0xE and 0xF do not appear to have anything connected to their
4290 * GPIOs.
4291 *
4292 * The correct GPIO_OUT_EN value might have some more bits set. It should
4293 * be possible to derive it from a boundary scan of the CPLD. Its JTAG
4294 * pins are routed to test points.
4295 *
4296 */
4297 /* ----------------------------------------------------------------------- */
4298 static void
init_PCI8604PW(struct bttv * btv)4299 init_PCI8604PW(struct bttv *btv)
4300 {
4301 int state;
4302
4303 if ((PCI_SLOT(btv->c.pci->devfn) & ~3) != 0xC) {
4304 pr_warn("This is not a PCI-8604PW\n");
4305 return;
4306 }
4307
4308 if (PCI_SLOT(btv->c.pci->devfn) != 0xD)
4309 return;
4310
4311 btwrite(0x080002, BT848_GPIO_OUT_EN);
4312
4313 state = (btread(BT848_GPIO_DATA) >> 21) & 7;
4314
4315 for (;;) {
4316 switch (state) {
4317 case 1:
4318 case 5:
4319 case 6:
4320 case 4:
4321 pr_debug("PCI-8604PW in state %i, toggling pin\n",
4322 state);
4323 btwrite(0x080000, BT848_GPIO_DATA);
4324 msleep(1);
4325 btwrite(0x000000, BT848_GPIO_DATA);
4326 msleep(1);
4327 break;
4328 case 7:
4329 pr_info("PCI-8604PW unlocked\n");
4330 return;
4331 case 0:
4332 /* FIXME: If we are in state 7 and toggle GPIO[19] one
4333 more time, the CPLD goes into state 0, where PCI bus
4334 mastering is inhibited again. We have not managed to
4335 get out of that state. */
4336
4337 pr_err("PCI-8604PW locked until reset\n");
4338 return;
4339 default:
4340 pr_err("PCI-8604PW in unknown state %i\n", state);
4341 return;
4342 }
4343
4344 state = (state << 4) | ((btread(BT848_GPIO_DATA) >> 21) & 7);
4345
4346 switch (state) {
4347 case 0x15:
4348 case 0x56:
4349 case 0x64:
4350 case 0x47:
4351 /* The transition from state 7 to state 0 is, as explained
4352 above, valid but undesired and with this code impossible
4353 as we exit as soon as we are in state 7.
4354 case 0x70: */
4355 break;
4356 default:
4357 pr_err("PCI-8604PW invalid transition %i -> %i\n",
4358 state >> 4, state & 7);
4359 return;
4360 }
4361 state &= 7;
4362 }
4363 }
4364
4365 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
4366 *
4367 * This is needed because rv605 don't use a normal multiplex, but a crosspoint
4368 * switch instead (CD22M3494E). This IC can have multiple active connections
4369 * between Xn (input) and Yn (output) pins. We need to clear any existing
4370 * connection prior to establish a new one, pulsing the STROBE pin.
4371 *
4372 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
4373 * GPIO pins are wired as:
4374 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
4375 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
4376 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller)
4377 * GPIO[8] - - P3[5] (microcontroller)
4378 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller)
4379 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller)
4380 * GPINTR - - P3[4] (microcontroller)
4381 *
4382 * The microcontroller is a 80C32 like. It should be possible to change xpoint
4383 * configuration either directly (as we are doing) or using the microcontroller
4384 * which is also wired to I2C interface. I have no further info on the
4385 * microcontroller features, one would need to disassembly the firmware.
4386 * note: the vendor refused to give any information on this product, all
4387 * that stuff was found using a multimeter! :)
4388 */
rv605_muxsel(struct bttv * btv,unsigned int input)4389 static void rv605_muxsel(struct bttv *btv, unsigned int input)
4390 {
4391 static const u8 muxgpio[] = { 0x3, 0x1, 0x2, 0x4, 0xf, 0x7, 0xe, 0x0,
4392 0xd, 0xb, 0xc, 0x6, 0x9, 0x5, 0x8, 0xa };
4393
4394 gpio_bits(0x07f, muxgpio[input]);
4395
4396 /* reset all connections */
4397 gpio_bits(0x200,0x200);
4398 mdelay(1);
4399 gpio_bits(0x200,0x000);
4400 mdelay(1);
4401
4402 /* create a new connection */
4403 gpio_bits(0x480,0x480);
4404 mdelay(1);
4405 gpio_bits(0x480,0x080);
4406 mdelay(1);
4407 }
4408
4409 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
4410 *
4411 * The CS16 (available on eBay cheap) is a PCI board with four Fusion
4412 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync separator
4413 * chips, ten eight input analog multiplexors, a not chip and a few
4414 * other components.
4415 *
4416 * 16 inputs on a secondary bracket are provided and can be selected
4417 * from each of the four capture chips. Two of the eight input
4418 * multiplexors are used to select from any of the 16 input signals.
4419 *
4420 * Unsupported hardware capabilities:
4421 * . A video output monitor on the secondary bracket can be selected from
4422 * one of the 878A chips.
4423 * . Another passthrough but I haven't spent any time investigating it.
4424 * . Digital I/O (logic level connected to GPIO) is available from an
4425 * onboard header.
4426 *
4427 * The on chip input mux should always be set to 2.
4428 * GPIO[16:19] - Video input selection
4429 * GPIO[0:3] - Video output monitor select (only available from one 878A)
4430 * GPIO[?:?] - Digital I/O.
4431 *
4432 * There is an ATMEL microcontroller with an 8031 core on board. I have not
4433 * determined what function (if any) it provides. With the microcontroller
4434 * and sync separator chips a guess is that it might have to do with video
4435 * switching and maybe some digital I/O.
4436 */
tibetCS16_muxsel(struct bttv * btv,unsigned int input)4437 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
4438 {
4439 /* video mux */
4440 gpio_bits(0x0f0000, input << 16);
4441 }
4442
tibetCS16_init(struct bttv * btv)4443 static void tibetCS16_init(struct bttv *btv)
4444 {
4445 /* enable gpio bits, mask obtained via btSpy */
4446 gpio_inout(0xffffff, 0x0f7fff);
4447 gpio_write(0x0f7fff);
4448 }
4449
4450 /*
4451 * The following routines for the Kodicom-4400r get a little mind-twisting.
4452 * There is a "master" controller and three "slave" controllers, together
4453 * an analog switch which connects any of 16 cameras to any of the BT87A's.
4454 * The analog switch is controlled by the "master", but the detection order
4455 * of the four BT878A chips is in an order which I just don't understand.
4456 * The "master" is actually the second controller to be detected. The
4457 * logic on the board uses logical numbers for the 4 controllers, but
4458 * those numbers are different from the detection sequence. When working
4459 * with the analog switch, we need to "map" from the detection sequence
4460 * over to the board's logical controller number. This mapping sequence
4461 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
4462 * unit 3, the second (which is the master) is logical unit 0, etc.
4463 * We need to maintain the status of the analog switch (which of the 16
4464 * cameras is connected to which of the 4 controllers) in sw_status array.
4465 */
4466
4467 /*
4468 * First a routine to set the analog switch, which controls which camera
4469 * is routed to which controller. The switch comprises an X-address
4470 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4471 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4472 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables
4473 * the switch. A STROBE bit (gpio bit 8) latches the data value into the
4474 * specified address. The idea is to set the address and data, then bring
4475 * STROBE high, and finally bring STROBE back to low.
4476 */
kodicom4400r_write(struct bttv * btv,unsigned char xaddr,unsigned char yaddr,unsigned char data)4477 static void kodicom4400r_write(struct bttv *btv,
4478 unsigned char xaddr,
4479 unsigned char yaddr,
4480 unsigned char data) {
4481 unsigned int udata;
4482
4483 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
4484 gpio_bits(0x1ff, udata); /* write ADDR and DAT */
4485 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
4486 gpio_bits(0x1ff, udata); /* strobe low */
4487 }
4488
4489 /*
4490 * Next the mux select. Both the "master" and "slave" 'cards' (controllers)
4491 * use this routine. The routine finds the "master" for the card, maps
4492 * the controller number from the detected position over to the logical
4493 * number, writes the appropriate data to the analog switch, and housekeeps
4494 * the local copy of the switch information. The parameter 'input' is the
4495 * requested camera number (0 - 15).
4496 */
kodicom4400r_muxsel(struct bttv * btv,unsigned int input)4497 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
4498 {
4499 int xaddr, yaddr;
4500 struct bttv *mctlr;
4501 static unsigned char map[4] = {3, 0, 2, 1};
4502
4503 mctlr = master[btv->c.nr];
4504 if (mctlr == NULL) { /* ignore if master not yet detected */
4505 return;
4506 }
4507 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
4508 yaddr = map[yaddr];
4509 xaddr = input & 0xf;
4510 /* Check if the controller/camera pair has changed, else ignore */
4511 if (mctlr->sw_status[yaddr] != xaddr)
4512 {
4513 /* "open" the old switch, "close" the new one, save the new */
4514 kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4515 mctlr->sw_status[yaddr] = xaddr;
4516 kodicom4400r_write(mctlr, xaddr, yaddr, 1);
4517 }
4518 }
4519
4520 /*
4521 * During initialisation, we need to reset the analog switch. We
4522 * also preset the switch to map the 4 connectors on the card to the
4523 * *user's* (see above description of kodicom4400r_muxsel) channels
4524 * 0 through 3
4525 */
kodicom4400r_init(struct bttv * btv)4526 static void kodicom4400r_init(struct bttv *btv)
4527 {
4528 int ix;
4529
4530 gpio_inout(0x0003ff, 0x0003ff);
4531 gpio_write(1 << 9); /* reset MUX */
4532 gpio_write(0);
4533 /* Preset camera 0 to the 4 controllers */
4534 for (ix = 0; ix < 4; ix++) {
4535 btv->sw_status[ix] = ix;
4536 kodicom4400r_write(btv, ix, ix, 1);
4537 }
4538 /*
4539 * Since this is the "master", we need to set up the
4540 * other three controller chips' pointers to this structure
4541 * for later use in the muxsel routine.
4542 */
4543 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
4544 return;
4545 master[btv->c.nr-1] = btv;
4546 master[btv->c.nr] = btv;
4547 master[btv->c.nr+1] = btv;
4548 master[btv->c.nr+2] = btv;
4549 }
4550
4551 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel
4552 * video multiplexers to provide up to 16 video inputs. These
4553 * multiplexers are controlled by the lower 8 GPIO pins of the
4554 * bt878. The multiplexers probably Pericom PI5V331Q or similar.
4555
4556 * xxx0 is pin xxx of multiplexer U5,
4557 * yyy1 is pin yyy of multiplexer U2
4558 */
4559 #define ENA0 0x01
4560 #define ENB0 0x02
4561 #define ENA1 0x04
4562 #define ENB1 0x08
4563
4564 #define IN10 0x10
4565 #define IN00 0x20
4566 #define IN11 0x40
4567 #define IN01 0x80
4568
xguard_muxsel(struct bttv * btv,unsigned int input)4569 static void xguard_muxsel(struct bttv *btv, unsigned int input)
4570 {
4571 static const int masks[] = {
4572 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
4573 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
4574 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
4575 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
4576 };
4577 gpio_write(masks[input%16]);
4578 }
picolo_tetra_init(struct bttv * btv)4579 static void picolo_tetra_init(struct bttv *btv)
4580 {
4581 /*This is the video input redirection functionality : I DID NOT USE IT. */
4582 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
4583 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/
4584 }
picolo_tetra_muxsel(struct bttv * btv,unsigned int input)4585 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
4586 {
4587
4588 dprintk("%d : picolo_tetra_muxsel => input = %d\n", btv->c.nr, input);
4589 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
4590 /*GPIO[20]&GPIO[21] used to choose the right input*/
4591 btwrite (input<<20,BT848_GPIO_DATA);
4592
4593 }
4594
4595 /*
4596 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
4597 *
4598 * The IVC120G security card has 4 i2c controlled TDA8540 matrix
4599 * switchers to provide 16 channels to MUX0. The TDA8540's have
4600 * 4 independent outputs and as such the IVC120G also has the
4601 * optional "Monitor Out" bus. This allows the card to be looking
4602 * at one input while the monitor is looking at another.
4603 *
4604 * Since I've couldn't be bothered figuring out how to add an
4605 * independent muxsel for the monitor bus, I've just set it to
4606 * whatever the card is looking at.
4607 *
4608 * OUT0 of the TDA8540's is connected to MUX0 (0x03)
4609 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C)
4610 *
4611 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03)
4612 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03)
4613 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03)
4614 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03)
4615 *
4616 */
4617
4618 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
4619 #define I2C_TDA8540 0x90
4620 #define I2C_TDA8540_ALT1 0x92
4621 #define I2C_TDA8540_ALT2 0x94
4622 #define I2C_TDA8540_ALT3 0x96
4623 #define I2C_TDA8540_ALT4 0x98
4624 #define I2C_TDA8540_ALT5 0x9a
4625 #define I2C_TDA8540_ALT6 0x9c
4626
ivc120_muxsel(struct bttv * btv,unsigned int input)4627 static void ivc120_muxsel(struct bttv *btv, unsigned int input)
4628 {
4629 /* Simple maths */
4630 int key = input % 4;
4631 int matrix = input / 4;
4632
4633 dprintk("%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
4634 btv->c.nr, input, matrix, key);
4635
4636 /* Handles the input selection on the TDA8540's */
4637 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
4638 ((matrix == 3) ? (key | key << 2) : 0x00), 1);
4639 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
4640 ((matrix == 0) ? (key | key << 2) : 0x00), 1);
4641 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
4642 ((matrix == 1) ? (key | key << 2) : 0x00), 1);
4643 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
4644 ((matrix == 2) ? (key | key << 2) : 0x00), 1);
4645
4646 /* Handles the output enables on the TDA8540's */
4647 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
4648 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */
4649 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
4650 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */
4651 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
4652 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */
4653 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
4654 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */
4655
4656 /* 878's MUX0 is already selected for input via muxsel values */
4657 }
4658
4659
4660 /* PXC200 muxsel helper
4661 * luke@syseng.anu.edu.au
4662 * another transplant
4663 * from Alessandro Rubini (rubini@linux.it)
4664 *
4665 * There are 4 kinds of cards:
4666 * PXC200L which is bt848
4667 * PXC200F which is bt848 with PIC controlling mux
4668 * PXC200AL which is bt878
4669 * PXC200AF which is bt878 with PIC controlling mux
4670 */
4671 #define PX_CFG_PXC200F 0x01
4672 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */
4673 #define PX_I2C_PIC 0x0f
4674 #define PX_PXC200A_CARDID 0x200a1295
4675 #define PX_I2C_CMD_CFG 0x00
4676
PXC200_muxsel(struct bttv * btv,unsigned int input)4677 static void PXC200_muxsel(struct bttv *btv, unsigned int input)
4678 {
4679 int rc;
4680 long mux;
4681 int bitmask;
4682 unsigned char buf[2];
4683
4684 /* Read PIC config to determine if this is a PXC200F */
4685 /* PX_I2C_CMD_CFG*/
4686 buf[0]=0;
4687 buf[1]=0;
4688 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
4689 if (rc) {
4690 pr_debug("%d: PXC200_muxsel: pic cfg write failed:%d\n",
4691 btv->c.nr, rc);
4692 /* not PXC ? do nothing */
4693 return;
4694 }
4695
4696 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
4697 if (!(rc & PX_CFG_PXC200F)) {
4698 pr_debug("%d: PXC200_muxsel: not PXC200F rc:%d\n",
4699 btv->c.nr, rc);
4700 return;
4701 }
4702
4703
4704 /* The multiplexer in the 200F is handled by the GPIO port */
4705 /* get correct mapping between inputs */
4706 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
4707 /* ** not needed!? */
4708 mux = input;
4709
4710 /* make sure output pins are enabled */
4711 /* bitmask=0x30f; */
4712 bitmask=0x302;
4713 /* check whether we have a PXC200A */
4714 if (btv->cardid == PX_PXC200A_CARDID) {
4715 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
4716 bitmask |= 7<<4; /* the DAC */
4717 }
4718 btwrite(bitmask, BT848_GPIO_OUT_EN);
4719
4720 bitmask = btread(BT848_GPIO_DATA);
4721 if (btv->cardid == PX_PXC200A_CARDID)
4722 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
4723 else /* older device */
4724 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
4725 btwrite(bitmask,BT848_GPIO_DATA);
4726
4727 /*
4728 * Was "to be safe, set the bt848 to input 0"
4729 * Actually, since it's ok at load time, better not messing
4730 * with these bits (on PXC200AF you need to set mux 2 here)
4731 *
4732 * needed because bttv-driver sets mux before calling this function
4733 */
4734 if (btv->cardid == PX_PXC200A_CARDID)
4735 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
4736 else /* older device */
4737 btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
4738
4739 pr_debug("%d: setting input channel to:%d\n", btv->c.nr, (int)mux);
4740 }
4741
phytec_muxsel(struct bttv * btv,unsigned int input)4742 static void phytec_muxsel(struct bttv *btv, unsigned int input)
4743 {
4744 unsigned int mux = input % 4;
4745
4746 if (input == btv->svhs)
4747 mux = 0;
4748
4749 gpio_bits(0x3, mux);
4750 }
4751
4752 /*
4753 * GeoVision GV-800(S) functions
4754 * Bruno Christo <bchristo@inf.ufsm.br>
4755 */
4756
4757 /* This is a function to control the analog switch, which determines which
4758 * camera is routed to which controller. The switch comprises an X-address
4759 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4760 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4761 * A data value (gpio bit 18) of '1' enables the switch, and '0' disables
4762 * the switch. A STROBE bit (gpio bit 17) latches the data value into the
4763 * specified address. There is also a chip select (gpio bit 16).
4764 * The idea is to set the address and chip select together, bring
4765 * STROBE high, write the data, and finally bring STROBE back to low.
4766 */
gv800s_write(struct bttv * btv,unsigned char xaddr,unsigned char yaddr,unsigned char data)4767 static void gv800s_write(struct bttv *btv,
4768 unsigned char xaddr,
4769 unsigned char yaddr,
4770 unsigned char data) {
4771 /* On the "master" 878A:
4772 * GPIO bits 0-9 are used for the analog switch:
4773 * 00 - 03: camera selector
4774 * 04 - 06: 878A (controller) selector
4775 * 16: cselect
4776 * 17: strobe
4777 * 18: data (1->on, 0->off)
4778 * 19: reset
4779 */
4780 const u32 ADDRESS = ((xaddr&0xf) | (yaddr&3)<<4);
4781 const u32 CSELECT = 1<<16;
4782 const u32 STROBE = 1<<17;
4783 const u32 DATA = data<<18;
4784
4785 gpio_bits(0x1007f, ADDRESS | CSELECT); /* write ADDRESS and CSELECT */
4786 gpio_bits(0x20000, STROBE); /* STROBE high */
4787 gpio_bits(0x40000, DATA); /* write DATA */
4788 gpio_bits(0x20000, ~STROBE); /* STROBE low */
4789 }
4790
4791 /*
4792 * GeoVision GV-800(S) muxsel
4793 *
4794 * Each of the 4 cards (controllers) use this function.
4795 * The controller using this function selects the input through the GPIO pins
4796 * of the "master" card. A pointer to this card is stored in master[btv->c.nr].
4797 *
4798 * The parameter 'input' is the requested camera number (0-4) on the controller.
4799 * The map array has the address of each input. Note that the addresses in the
4800 * array are in the sequence the original GeoVision driver uses, that is, set
4801 * every controller to input 0, then to input 1, 2, 3, repeat. This means that
4802 * the physical "camera 1" connector corresponds to controller 0 input 0,
4803 * "camera 2" corresponds to controller 1 input 0, and so on.
4804 *
4805 * After getting the input address, the function then writes the appropriate
4806 * data to the analog switch, and housekeeps the local copy of the switch
4807 * information.
4808 */
gv800s_muxsel(struct bttv * btv,unsigned int input)4809 static void gv800s_muxsel(struct bttv *btv, unsigned int input)
4810 {
4811 struct bttv *mctlr;
4812 int xaddr, yaddr;
4813 static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 },
4814 { 0x1, 0x5, 0xb, 0x7 },
4815 { 0x2, 0x8, 0xc, 0xe },
4816 { 0x3, 0x9, 0xd, 0xf } };
4817 input = input%4;
4818 mctlr = master[btv->c.nr];
4819 if (mctlr == NULL) {
4820 /* do nothing until the "master" is detected */
4821 return;
4822 }
4823 yaddr = (btv->c.nr - mctlr->c.nr) & 3;
4824 xaddr = map[yaddr][input] & 0xf;
4825
4826 /* Check if the controller/camera pair has changed, ignore otherwise */
4827 if (mctlr->sw_status[yaddr] != xaddr) {
4828 /* disable the old switch, enable the new one and save status */
4829 gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4830 mctlr->sw_status[yaddr] = xaddr;
4831 gv800s_write(mctlr, xaddr, yaddr, 1);
4832 }
4833 }
4834
4835 /* GeoVision GV-800(S) "master" chip init */
gv800s_init(struct bttv * btv)4836 static void gv800s_init(struct bttv *btv)
4837 {
4838 int ix;
4839
4840 gpio_inout(0xf107f, 0xf107f);
4841 gpio_write(1<<19); /* reset the analog MUX */
4842 gpio_write(0);
4843
4844 /* Preset camera 0 to the 4 controllers */
4845 for (ix = 0; ix < 4; ix++) {
4846 btv->sw_status[ix] = ix;
4847 gv800s_write(btv, ix, ix, 1);
4848 }
4849
4850 /* Inputs on the "master" controller need this brightness fix */
4851 bttv_I2CWrite(btv, 0x18, 0x5, 0x90, 1);
4852
4853 if (btv->c.nr > BTTV_MAX-4)
4854 return;
4855 /*
4856 * Store the "master" controller pointer in the master
4857 * array for later use in the muxsel function.
4858 */
4859 master[btv->c.nr] = btv;
4860 master[btv->c.nr+1] = btv;
4861 master[btv->c.nr+2] = btv;
4862 master[btv->c.nr+3] = btv;
4863 }
4864
4865 /* ----------------------------------------------------------------------- */
4866 /* motherboard chipset specific stuff */
4867
bttv_check_chipset(void)4868 void __init bttv_check_chipset(void)
4869 {
4870 struct pci_dev *dev = NULL;
4871
4872 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
4873 triton1 = 1;
4874 if (pci_pci_problems & PCIPCI_VSFX)
4875 vsfx = 1;
4876 #ifdef PCIPCI_ALIMAGIK
4877 if (pci_pci_problems & PCIPCI_ALIMAGIK)
4878 latency = 0x0A;
4879 #endif
4880
4881
4882 /* print warnings about any quirks found */
4883 if (triton1)
4884 pr_info("Host bridge needs ETBF enabled\n");
4885 if (vsfx)
4886 pr_info("Host bridge needs VSFX enabled\n");
4887 if (UNSET != latency)
4888 pr_info("pci latency fixup [%d]\n", latency);
4889 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL,
4890 PCI_DEVICE_ID_INTEL_82441, dev))) {
4891 unsigned char b;
4892 pci_read_config_byte(dev, 0x53, &b);
4893 if (bttv_debug)
4894 pr_info("Host bridge: 82441FX Natoma, bufcon=0x%02x\n",
4895 b);
4896 }
4897 }
4898
bttv_handle_chipset(struct bttv * btv)4899 int bttv_handle_chipset(struct bttv *btv)
4900 {
4901 unsigned char command;
4902
4903 if (!triton1 && !vsfx && UNSET == latency)
4904 return 0;
4905
4906 if (bttv_verbose) {
4907 if (triton1)
4908 pr_info("%d: enabling ETBF (430FX/VP3 compatibility)\n",
4909 btv->c.nr);
4910 if (vsfx && btv->id >= 878)
4911 pr_info("%d: enabling VSFX\n", btv->c.nr);
4912 if (UNSET != latency)
4913 pr_info("%d: setting pci timer to %d\n",
4914 btv->c.nr, latency);
4915 }
4916
4917 if (btv->id < 878) {
4918 /* bt848 (mis)uses a bit in the irq mask for etbf */
4919 if (triton1)
4920 btv->triton1 = BT848_INT_ETBF;
4921 } else {
4922 /* bt878 has a bit in the pci config space for it */
4923 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
4924 if (triton1)
4925 command |= BT878_EN_TBFX;
4926 if (vsfx)
4927 command |= BT878_EN_VSFX;
4928 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
4929 }
4930 if (UNSET != latency)
4931 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
4932 return 0;
4933 }
4934