xref: /linux/sound/soc/codecs/tlv320adc3xxx.c (revision a1ff5a7d78a036d6c2178ee5acd6ba4946243800)
1 // SPDX-License-Identifier: GPL-2.0-only
2 //
3 // Based on sound/soc/codecs/tlv320aic3x.c by  Vladimir Barinov
4 //
5 // Copyright (C) 2010 Mistral Solutions Pvt Ltd.
6 // Author: Shahina Shaik <shahina.s@mistralsolutions.com>
7 //
8 // Copyright (C) 2014-2018, Ambarella, Inc.
9 // Author: Dongge wu <dgwu@ambarella.com>
10 //
11 // Copyright (C) 2021 Axis Communications AB
12 // Author: Ricard Wanderlof <ricardw@axis.com>
13 //
14 
15 #include <dt-bindings/sound/tlv320adc3xxx.h>
16 #include <linux/clk.h>
17 #include <linux/gpio/consumer.h>
18 #include <linux/module.h>
19 #include <linux/moduleparam.h>
20 #include <linux/io.h>
21 #include <linux/init.h>
22 #include <linux/delay.h>
23 #include <linux/gpio/driver.h>
24 #include <linux/pm.h>
25 #include <linux/i2c.h>
26 #include <linux/platform_device.h>
27 #include <linux/cdev.h>
28 #include <linux/slab.h>
29 #include <sound/core.h>
30 #include <sound/pcm.h>
31 #include <sound/pcm_params.h>
32 #include <sound/soc.h>
33 #include <sound/soc-dapm.h>
34 #include <sound/tlv.h>
35 #include <sound/initval.h>
36 
37 /*
38  * General definitions defining exported functionality.
39  */
40 
41 #define ADC3XXX_MICBIAS_PINS		2
42 #define ADC3XXX_GPIO_PINS		2
43 
44 /* Number of GPIO pins exposed via the gpiolib interface */
45 #define ADC3XXX_GPIOS_MAX		(ADC3XXX_MICBIAS_PINS + ADC3XXX_GPIO_PINS)
46 
47 #define ADC3XXX_RATES		SNDRV_PCM_RATE_8000_96000
48 #define ADC3XXX_FORMATS		(SNDRV_PCM_FMTBIT_S16_LE | \
49 				 SNDRV_PCM_FMTBIT_S20_3LE | \
50 				 SNDRV_PCM_FMTBIT_S24_3LE | \
51 				 SNDRV_PCM_FMTBIT_S32_LE)
52 
53 /*
54  * PLL modes, to be used for clk_id for set_sysclk callback.
55  *
56  * The default behavior (AUTO) is to take the first matching entry in the clock
57  * table, which is intended to be the PLL based one if there is more than one.
58  *
59  * Setting the clock source using simple-card (clocks or
60  * system-clock-frequency property) sets clk_id = 0 = ADC3XXX_PLL_AUTO.
61  */
62 #define ADC3XXX_PLL_AUTO	0 /* Use first available mode */
63 #define ADC3XXX_PLL_ENABLE	1 /* Use PLL for clock generation */
64 #define ADC3XXX_PLL_BYPASS	2 /* Don't use PLL for clock generation */
65 
66 /* Register definitions. */
67 
68 #define ADC3XXX_PAGE_SIZE		128
69 #define ADC3XXX_REG(page, reg)		((page * ADC3XXX_PAGE_SIZE) + reg)
70 
71 /*
72  * Page 0 registers.
73  */
74 
75 #define ADC3XXX_PAGE_SELECT			ADC3XXX_REG(0, 0)
76 #define ADC3XXX_RESET				ADC3XXX_REG(0, 1)
77 
78 /* 2-3 Reserved */
79 
80 #define ADC3XXX_CLKGEN_MUX			ADC3XXX_REG(0, 4)
81 #define ADC3XXX_PLL_PROG_PR			ADC3XXX_REG(0, 5)
82 #define ADC3XXX_PLL_PROG_J			ADC3XXX_REG(0, 6)
83 #define ADC3XXX_PLL_PROG_D_MSB			ADC3XXX_REG(0, 7)
84 #define ADC3XXX_PLL_PROG_D_LSB			ADC3XXX_REG(0, 8)
85 
86 /* 9-17 Reserved */
87 
88 #define ADC3XXX_ADC_NADC			ADC3XXX_REG(0, 18)
89 #define ADC3XXX_ADC_MADC			ADC3XXX_REG(0, 19)
90 #define ADC3XXX_ADC_AOSR			ADC3XXX_REG(0, 20)
91 #define ADC3XXX_ADC_IADC			ADC3XXX_REG(0, 21)
92 
93 /* 23-24 Reserved */
94 
95 #define ADC3XXX_CLKOUT_MUX			ADC3XXX_REG(0, 25)
96 #define ADC3XXX_CLKOUT_M_DIV			ADC3XXX_REG(0, 26)
97 #define ADC3XXX_INTERFACE_CTRL_1		ADC3XXX_REG(0, 27)
98 #define ADC3XXX_CH_OFFSET_1			ADC3XXX_REG(0, 28)
99 #define ADC3XXX_INTERFACE_CTRL_2		ADC3XXX_REG(0, 29)
100 #define ADC3XXX_BCLK_N_DIV			ADC3XXX_REG(0, 30)
101 #define ADC3XXX_INTERFACE_CTRL_3		ADC3XXX_REG(0, 31)
102 #define ADC3XXX_INTERFACE_CTRL_4		ADC3XXX_REG(0, 32)
103 #define ADC3XXX_INTERFACE_CTRL_5		ADC3XXX_REG(0, 33)
104 #define ADC3XXX_I2S_SYNC			ADC3XXX_REG(0, 34)
105 /* 35 Reserved */
106 #define ADC3XXX_ADC_FLAG			ADC3XXX_REG(0, 36)
107 #define ADC3XXX_CH_OFFSET_2			ADC3XXX_REG(0, 37)
108 #define ADC3XXX_I2S_TDM_CTRL			ADC3XXX_REG(0, 38)
109 /* 39-41 Reserved */
110 #define ADC3XXX_INTR_FLAG_1			ADC3XXX_REG(0, 42)
111 #define ADC3XXX_INTR_FLAG_2			ADC3XXX_REG(0, 43)
112 /* 44 Reserved */
113 #define ADC3XXX_INTR_FLAG_ADC1			ADC3XXX_REG(0, 45)
114 /* 46 Reserved */
115 #define ADC3XXX_INTR_FLAG_ADC2			ADC3XXX_REG(0, 47)
116 #define ADC3XXX_INT1_CTRL			ADC3XXX_REG(0, 48)
117 #define ADC3XXX_INT2_CTRL			ADC3XXX_REG(0, 49)
118 /* 50 Reserved */
119 #define ADC3XXX_GPIO2_CTRL			ADC3XXX_REG(0, 51)
120 #define ADC3XXX_GPIO1_CTRL			ADC3XXX_REG(0, 52)
121 #define ADC3XXX_DOUT_CTRL			ADC3XXX_REG(0, 53)
122 /* 54-56 Reserved */
123 #define ADC3XXX_SYNC_CTRL_1			ADC3XXX_REG(0, 57)
124 #define ADC3XXX_SYNC_CTRL_2			ADC3XXX_REG(0, 58)
125 #define ADC3XXX_CIC_GAIN_CTRL			ADC3XXX_REG(0, 59)
126 /* 60 Reserved */
127 #define ADC3XXX_PRB_SELECT			ADC3XXX_REG(0, 61)
128 #define ADC3XXX_INST_MODE_CTRL			ADC3XXX_REG(0, 62)
129 /* 63-79 Reserved */
130 #define ADC3XXX_MIC_POLARITY_CTRL		ADC3XXX_REG(0, 80)
131 #define ADC3XXX_ADC_DIGITAL			ADC3XXX_REG(0, 81)
132 #define	ADC3XXX_ADC_FGA				ADC3XXX_REG(0, 82)
133 #define ADC3XXX_LADC_VOL			ADC3XXX_REG(0, 83)
134 #define ADC3XXX_RADC_VOL			ADC3XXX_REG(0, 84)
135 #define ADC3XXX_ADC_PHASE_COMP			ADC3XXX_REG(0, 85)
136 #define ADC3XXX_LEFT_CHN_AGC_1			ADC3XXX_REG(0, 86)
137 #define ADC3XXX_LEFT_CHN_AGC_2			ADC3XXX_REG(0, 87)
138 #define ADC3XXX_LEFT_CHN_AGC_3			ADC3XXX_REG(0, 88)
139 #define ADC3XXX_LEFT_CHN_AGC_4			ADC3XXX_REG(0, 89)
140 #define ADC3XXX_LEFT_CHN_AGC_5			ADC3XXX_REG(0, 90)
141 #define ADC3XXX_LEFT_CHN_AGC_6			ADC3XXX_REG(0, 91)
142 #define ADC3XXX_LEFT_CHN_AGC_7			ADC3XXX_REG(0, 92)
143 #define ADC3XXX_LEFT_AGC_GAIN			ADC3XXX_REG(0, 93)
144 #define ADC3XXX_RIGHT_CHN_AGC_1			ADC3XXX_REG(0, 94)
145 #define ADC3XXX_RIGHT_CHN_AGC_2			ADC3XXX_REG(0, 95)
146 #define ADC3XXX_RIGHT_CHN_AGC_3			ADC3XXX_REG(0, 96)
147 #define ADC3XXX_RIGHT_CHN_AGC_4			ADC3XXX_REG(0, 97)
148 #define ADC3XXX_RIGHT_CHN_AGC_5			ADC3XXX_REG(0, 98)
149 #define ADC3XXX_RIGHT_CHN_AGC_6			ADC3XXX_REG(0, 99)
150 #define ADC3XXX_RIGHT_CHN_AGC_7			ADC3XXX_REG(0, 100)
151 #define ADC3XXX_RIGHT_AGC_GAIN			ADC3XXX_REG(0, 101)
152 /* 102-127 Reserved */
153 
154 /*
155  * Page 1 registers.
156  */
157 
158 /* 1-25 Reserved */
159 #define ADC3XXX_DITHER_CTRL			ADC3XXX_REG(1, 26)
160 /* 27-50 Reserved */
161 #define ADC3XXX_MICBIAS_CTRL			ADC3XXX_REG(1, 51)
162 #define ADC3XXX_LEFT_PGA_SEL_1			ADC3XXX_REG(1, 52)
163 /* 53 Reserved */
164 #define ADC3XXX_LEFT_PGA_SEL_2			ADC3XXX_REG(1, 54)
165 #define ADC3XXX_RIGHT_PGA_SEL_1			ADC3XXX_REG(1, 55)
166 #define ADC3XXX_RIGHT_PGA_SEL_2			ADC3XXX_REG(1, 57)
167 #define ADC3XXX_LEFT_APGA_CTRL			ADC3XXX_REG(1, 59)
168 #define ADC3XXX_RIGHT_APGA_CTRL			ADC3XXX_REG(1, 60)
169 #define ADC3XXX_LOW_CURRENT_MODES		ADC3XXX_REG(1, 61)
170 #define ADC3XXX_ANALOG_PGA_FLAGS		ADC3XXX_REG(1, 62)
171 /* 63-127 Reserved */
172 
173 /*
174  * Page 4 registers. First page of coefficient memory for the miniDSP.
175  */
176 #define ADC3XXX_LEFT_ADC_IIR_COEFF_N0_MSB	ADC3XXX_REG(4, 8)
177 #define ADC3XXX_LEFT_ADC_IIR_COEFF_N0_LSB	ADC3XXX_REG(4, 9)
178 #define ADC3XXX_LEFT_ADC_IIR_COEFF_N1_MSB	ADC3XXX_REG(4, 10)
179 #define ADC3XXX_LEFT_ADC_IIR_COEFF_N1_LSB	ADC3XXX_REG(4, 11)
180 #define ADC3XXX_LEFT_ADC_IIR_COEFF_D1_MSB	ADC3XXX_REG(4, 12)
181 #define ADC3XXX_LEFT_ADC_IIR_COEFF_D1_LSB	ADC3XXX_REG(4, 13)
182 
183 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_N0_MSB	ADC3XXX_REG(4, 72)
184 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_N0_LSB	ADC3XXX_REG(4, 73)
185 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_N1_MSB	ADC3XXX_REG(4, 74)
186 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_N1_LSB	ADC3XXX_REG(4, 75)
187 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_D1_MSB	ADC3XXX_REG(4, 76)
188 #define ADC3XXX_RIGHT_ADC_IIR_COEFF_D1_LSB	ADC3XXX_REG(4, 77)
189 
190 /*
191  * Register bits.
192  */
193 
194 /* PLL Enable bits */
195 #define ADC3XXX_ENABLE_PLL_SHIFT	7
196 #define ADC3XXX_ENABLE_PLL		(1 << ADC3XXX_ENABLE_PLL_SHIFT)
197 #define ADC3XXX_ENABLE_NADC_SHIFT	7
198 #define ADC3XXX_ENABLE_NADC		(1 << ADC3XXX_ENABLE_NADC_SHIFT)
199 #define ADC3XXX_ENABLE_MADC_SHIFT	7
200 #define ADC3XXX_ENABLE_MADC		(1 << ADC3XXX_ENABLE_MADC_SHIFT)
201 #define ADC3XXX_ENABLE_BCLK_SHIFT	7
202 #define ADC3XXX_ENABLE_BCLK		(1 << ADC3XXX_ENABLE_BCLK_SHIFT)
203 
204 /* Power bits */
205 #define ADC3XXX_LADC_PWR_ON		0x80
206 #define ADC3XXX_RADC_PWR_ON		0x40
207 
208 #define ADC3XXX_SOFT_RESET		0x01
209 #define ADC3XXX_BCLK_MASTER		0x08
210 #define ADC3XXX_WCLK_MASTER		0x04
211 
212 /* Interface register masks */
213 #define ADC3XXX_FORMAT_MASK		0xc0
214 #define ADC3XXX_FORMAT_SHIFT		6
215 #define ADC3XXX_WLENGTH_MASK		0x30
216 #define ADC3XXX_WLENGTH_SHIFT		4
217 #define ADC3XXX_CLKDIR_MASK		0x0c
218 #define ADC3XXX_CLKDIR_SHIFT		2
219 
220 /* Interface register bit patterns */
221 #define ADC3XXX_FORMAT_I2S		(0 << ADC3XXX_FORMAT_SHIFT)
222 #define ADC3XXX_FORMAT_DSP		(1 << ADC3XXX_FORMAT_SHIFT)
223 #define ADC3XXX_FORMAT_RJF		(2 << ADC3XXX_FORMAT_SHIFT)
224 #define ADC3XXX_FORMAT_LJF		(3 << ADC3XXX_FORMAT_SHIFT)
225 
226 #define ADC3XXX_IFACE_16BITS		(0 << ADC3XXX_WLENGTH_SHIFT)
227 #define ADC3XXX_IFACE_20BITS		(1 << ADC3XXX_WLENGTH_SHIFT)
228 #define ADC3XXX_IFACE_24BITS		(2 << ADC3XXX_WLENGTH_SHIFT)
229 #define ADC3XXX_IFACE_32BITS		(3 << ADC3XXX_WLENGTH_SHIFT)
230 
231 /* PLL P/R bit offsets */
232 #define ADC3XXX_PLLP_SHIFT		4
233 #define ADC3XXX_PLLR_SHIFT		0
234 #define ADC3XXX_PLL_PR_MASK		0x7f
235 #define ADC3XXX_PLLJ_MASK		0x3f
236 #define ADC3XXX_PLLD_MSB_MASK		0x3f
237 #define ADC3XXX_PLLD_LSB_MASK		0xff
238 #define ADC3XXX_NADC_MASK		0x7f
239 #define ADC3XXX_MADC_MASK		0x7f
240 #define ADC3XXX_AOSR_MASK		0xff
241 #define ADC3XXX_IADC_MASK		0xff
242 #define ADC3XXX_BDIV_MASK		0x7f
243 
244 /* PLL_CLKIN bits */
245 #define ADC3XXX_PLL_CLKIN_SHIFT		2
246 #define ADC3XXX_PLL_CLKIN_MCLK		0x0
247 #define ADC3XXX_PLL_CLKIN_BCLK		0x1
248 #define ADC3XXX_PLL_CLKIN_ZERO		0x3
249 
250 /* CODEC_CLKIN bits */
251 #define ADC3XXX_CODEC_CLKIN_SHIFT	0
252 #define ADC3XXX_CODEC_CLKIN_MCLK	0x0
253 #define ADC3XXX_CODEC_CLKIN_BCLK	0x1
254 #define ADC3XXX_CODEC_CLKIN_PLL_CLK	0x3
255 
256 #define ADC3XXX_USE_PLL	((ADC3XXX_PLL_CLKIN_MCLK << ADC3XXX_PLL_CLKIN_SHIFT) | \
257 			 (ADC3XXX_CODEC_CLKIN_PLL_CLK << ADC3XXX_CODEC_CLKIN_SHIFT))
258 #define ADC3XXX_NO_PLL	((ADC3XXX_PLL_CLKIN_ZERO << ADC3XXX_PLL_CLKIN_SHIFT) | \
259 			 (ADC3XXX_CODEC_CLKIN_MCLK << ADC3XXX_CODEC_CLKIN_SHIFT))
260 
261 /*  Analog PGA control bits */
262 #define ADC3XXX_LPGA_MUTE		0x80
263 #define ADC3XXX_RPGA_MUTE		0x80
264 
265 #define ADC3XXX_LPGA_GAIN_MASK		0x7f
266 #define ADC3XXX_RPGA_GAIN_MASK		0x7f
267 
268 /* ADC current modes */
269 #define ADC3XXX_ADC_LOW_CURR_MODE	0x01
270 
271 /* Left ADC Input selection bits */
272 #define ADC3XXX_LCH_SEL1_SHIFT		0
273 #define ADC3XXX_LCH_SEL2_SHIFT		2
274 #define ADC3XXX_LCH_SEL3_SHIFT		4
275 #define ADC3XXX_LCH_SEL4_SHIFT		6
276 
277 #define ADC3XXX_LCH_SEL1X_SHIFT		0
278 #define ADC3XXX_LCH_SEL2X_SHIFT		2
279 #define ADC3XXX_LCH_SEL3X_SHIFT		4
280 #define ADC3XXX_LCH_COMMON_MODE		0x40
281 #define ADC3XXX_BYPASS_LPGA		0x80
282 
283 /* Right ADC Input selection bits */
284 #define ADC3XXX_RCH_SEL1_SHIFT		0
285 #define ADC3XXX_RCH_SEL2_SHIFT		2
286 #define ADC3XXX_RCH_SEL3_SHIFT		4
287 #define ADC3XXX_RCH_SEL4_SHIFT		6
288 
289 #define ADC3XXX_RCH_SEL1X_SHIFT		0
290 #define ADC3XXX_RCH_SEL2X_SHIFT		2
291 #define ADC3XXX_RCH_SEL3X_SHIFT		4
292 #define ADC3XXX_RCH_COMMON_MODE		0x40
293 #define ADC3XXX_BYPASS_RPGA		0x80
294 
295 /* MICBIAS control bits */
296 #define ADC3XXX_MICBIAS_MASK		0x3
297 #define ADC3XXX_MICBIAS1_SHIFT		5
298 #define ADC3XXX_MICBIAS2_SHIFT		3
299 
300 #define ADC3XXX_ADC_MAX_VOLUME		64
301 #define ADC3XXX_ADC_POS_VOL		24
302 
303 /* GPIO control bits (GPIO1_CTRL and GPIO2_CTRL) */
304 #define ADC3XXX_GPIO_CTRL_CFG_MASK		0x3c
305 #define ADC3XXX_GPIO_CTRL_CFG_SHIFT		2
306 #define ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK	0x01
307 #define ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_SHIFT	0
308 #define ADC3XXX_GPIO_CTRL_INPUT_VALUE_MASK	0x02
309 #define ADC3XXX_GPIO_CTRL_INPUT_VALUE_SHIFT	1
310 
311 enum adc3xxx_type {
312 	ADC3001 = 0,
313 	ADC3101
314 };
315 
316 struct adc3xxx {
317 	struct device *dev;
318 	enum adc3xxx_type type;
319 	struct clk *mclk;
320 	struct regmap *regmap;
321 	struct gpio_desc *rst_pin;
322 	unsigned int pll_mode;
323 	unsigned int sysclk;
324 	unsigned int gpio_cfg[ADC3XXX_GPIO_PINS]; /* value+1 (0 => not set)  */
325 	unsigned int micbias_gpo[ADC3XXX_MICBIAS_PINS]; /* 1 => pin is GPO */
326 	unsigned int micbias_vg[ADC3XXX_MICBIAS_PINS];
327 	int master;
328 	u8 page_no;
329 	int use_pll;
330 	struct gpio_chip gpio_chip;
331 };
332 
333 static const unsigned int adc3xxx_gpio_ctrl_reg[ADC3XXX_GPIO_PINS] = {
334 	ADC3XXX_GPIO1_CTRL,
335 	ADC3XXX_GPIO2_CTRL
336 };
337 
338 static const unsigned int adc3xxx_micbias_shift[ADC3XXX_MICBIAS_PINS] = {
339 	ADC3XXX_MICBIAS1_SHIFT,
340 	ADC3XXX_MICBIAS2_SHIFT
341 };
342 
343 static const struct reg_default adc3xxx_defaults[] = {
344 	/* Page 0 */
345 	{ 0, 0x00 },    { 1, 0x00 },    { 2, 0x00 },    { 3, 0x00 },
346 	{ 4, 0x00 },    { 5, 0x11 },    { 6, 0x04 },    { 7, 0x00 },
347 	{ 8, 0x00 },    { 9, 0x00 },    { 10, 0x00 },   { 11, 0x00 },
348 	{ 12, 0x00 },   { 13, 0x00 },   { 14, 0x00 },   { 15, 0x00 },
349 	{ 16, 0x00 },   { 17, 0x00 },   { 18, 0x01 },   { 19, 0x01 },
350 	{ 20, 0x80 },   { 21, 0x80 },   { 22, 0x04 },   { 23, 0x00 },
351 	{ 24, 0x00 },   { 25, 0x00 },   { 26, 0x01 },   { 27, 0x00 },
352 	{ 28, 0x00 },   { 29, 0x02 },   { 30, 0x01 },   { 31, 0x00 },
353 	{ 32, 0x00 },   { 33, 0x10 },   { 34, 0x00 },   { 35, 0x00 },
354 	{ 36, 0x00 },   { 37, 0x00 },   { 38, 0x02 },   { 39, 0x00 },
355 	{ 40, 0x00 },   { 41, 0x00 },   { 42, 0x00 },   { 43, 0x00 },
356 	{ 44, 0x00 },   { 45, 0x00 },   { 46, 0x00 },   { 47, 0x00 },
357 	{ 48, 0x00 },   { 49, 0x00 },   { 50, 0x00 },   { 51, 0x00 },
358 	{ 52, 0x00 },   { 53, 0x12 },   { 54, 0x00 },   { 55, 0x00 },
359 	{ 56, 0x00 },   { 57, 0x00 },   { 58, 0x00 },   { 59, 0x44 },
360 	{ 60, 0x00 },   { 61, 0x01 },   { 62, 0x00 },   { 63, 0x00 },
361 	{ 64, 0x00 },   { 65, 0x00 },   { 66, 0x00 },   { 67, 0x00 },
362 	{ 68, 0x00 },   { 69, 0x00 },   { 70, 0x00 },   { 71, 0x00 },
363 	{ 72, 0x00 },   { 73, 0x00 },   { 74, 0x00 },   { 75, 0x00 },
364 	{ 76, 0x00 },   { 77, 0x00 },   { 78, 0x00 },   { 79, 0x00 },
365 	{ 80, 0x00 },   { 81, 0x00 },   { 82, 0x88 },   { 83, 0x00 },
366 	{ 84, 0x00 },   { 85, 0x00 },   { 86, 0x00 },   { 87, 0x00 },
367 	{ 88, 0x7f },   { 89, 0x00 },   { 90, 0x00 },   { 91, 0x00 },
368 	{ 92, 0x00 },   { 93, 0x00 },   { 94, 0x00 },   { 95, 0x00 },
369 	{ 96, 0x7f },   { 97, 0x00 },   { 98, 0x00 },   { 99, 0x00 },
370 	{ 100, 0x00 },  { 101, 0x00 },  { 102, 0x00 },  { 103, 0x00 },
371 	{ 104, 0x00 },  { 105, 0x00 },  { 106, 0x00 },  { 107, 0x00 },
372 	{ 108, 0x00 },  { 109, 0x00 },  { 110, 0x00 },  { 111, 0x00 },
373 	{ 112, 0x00 },  { 113, 0x00 },  { 114, 0x00 },  { 115, 0x00 },
374 	{ 116, 0x00 },  { 117, 0x00 },  { 118, 0x00 },  { 119, 0x00 },
375 	{ 120, 0x00 },  { 121, 0x00 },  { 122, 0x00 },  { 123, 0x00 },
376 	{ 124, 0x00 },  { 125, 0x00 },  { 126, 0x00 },  { 127, 0x00 },
377 
378 	/* Page 1 */
379 	{ 128, 0x00 },  { 129, 0x00 },  { 130, 0x00 },  { 131, 0x00 },
380 	{ 132, 0x00 },  { 133, 0x00 },  { 134, 0x00 },  { 135, 0x00 },
381 	{ 136, 0x00 },  { 137, 0x00 },  { 138, 0x00 },  { 139, 0x00 },
382 	{ 140, 0x00 },  { 141, 0x00 },  { 142, 0x00 },  { 143, 0x00 },
383 	{ 144, 0x00 },  { 145, 0x00 },  { 146, 0x00 },  { 147, 0x00 },
384 	{ 148, 0x00 },  { 149, 0x00 },  { 150, 0x00 },  { 151, 0x00 },
385 	{ 152, 0x00 },  { 153, 0x00 },  { 154, 0x00 },  { 155, 0x00 },
386 	{ 156, 0x00 },  { 157, 0x00 },  { 158, 0x00 },  { 159, 0x00 },
387 	{ 160, 0x00 },  { 161, 0x00 },  { 162, 0x00 },  { 163, 0x00 },
388 	{ 164, 0x00 },  { 165, 0x00 },  { 166, 0x00 },  { 167, 0x00 },
389 	{ 168, 0x00 },  { 169, 0x00 },  { 170, 0x00 },  { 171, 0x00 },
390 	{ 172, 0x00 },  { 173, 0x00 },  { 174, 0x00 },  { 175, 0x00 },
391 	{ 176, 0x00 },  { 177, 0x00 },  { 178, 0x00 },  { 179, 0x00 },
392 	{ 180, 0xff },  { 181, 0x00 },  { 182, 0x3f },  { 183, 0xff },
393 	{ 184, 0x00 },  { 185, 0x3f },  { 186, 0x00 },  { 187, 0x80 },
394 	{ 188, 0x80 },  { 189, 0x00 },  { 190, 0x00 },  { 191, 0x00 },
395 
396 	/* Page 4 */
397 	{ 1024, 0x00 },			{ 1026, 0x01 },	{ 1027, 0x17 },
398 	{ 1028, 0x01 }, { 1029, 0x17 }, { 1030, 0x7d }, { 1031, 0xd3 },
399 	{ 1032, 0x7f }, { 1033, 0xff }, { 1034, 0x00 }, { 1035, 0x00 },
400 	{ 1036, 0x00 }, { 1037, 0x00 }, { 1038, 0x7f }, { 1039, 0xff },
401 	{ 1040, 0x00 }, { 1041, 0x00 }, { 1042, 0x00 }, { 1043, 0x00 },
402 	{ 1044, 0x00 }, { 1045, 0x00 }, { 1046, 0x00 }, { 1047, 0x00 },
403 	{ 1048, 0x7f }, { 1049, 0xff }, { 1050, 0x00 }, { 1051, 0x00 },
404 	{ 1052, 0x00 }, { 1053, 0x00 }, { 1054, 0x00 }, { 1055, 0x00 },
405 	{ 1056, 0x00 }, { 1057, 0x00 }, { 1058, 0x7f }, { 1059, 0xff },
406 	{ 1060, 0x00 }, { 1061, 0x00 }, { 1062, 0x00 }, { 1063, 0x00 },
407 	{ 1064, 0x00 }, { 1065, 0x00 }, { 1066, 0x00 }, { 1067, 0x00 },
408 	{ 1068, 0x7f }, { 1069, 0xff }, { 1070, 0x00 }, { 1071, 0x00 },
409 	{ 1072, 0x00 }, { 1073, 0x00 }, { 1074, 0x00 }, { 1075, 0x00 },
410 	{ 1076, 0x00 }, { 1077, 0x00 }, { 1078, 0x7f }, { 1079, 0xff },
411 	{ 1080, 0x00 }, { 1081, 0x00 }, { 1082, 0x00 }, { 1083, 0x00 },
412 	{ 1084, 0x00 }, { 1085, 0x00 }, { 1086, 0x00 }, { 1087, 0x00 },
413 	{ 1088, 0x00 }, { 1089, 0x00 }, { 1090, 0x00 }, { 1091, 0x00 },
414 	{ 1092, 0x00 }, { 1093, 0x00 }, { 1094, 0x00 }, { 1095, 0x00 },
415 	{ 1096, 0x00 }, { 1097, 0x00 }, { 1098, 0x00 }, { 1099, 0x00 },
416 	{ 1100, 0x00 }, { 1101, 0x00 }, { 1102, 0x00 }, { 1103, 0x00 },
417 	{ 1104, 0x00 }, { 1105, 0x00 }, { 1106, 0x00 }, { 1107, 0x00 },
418 	{ 1108, 0x00 }, { 1109, 0x00 }, { 1110, 0x00 }, { 1111, 0x00 },
419 	{ 1112, 0x00 }, { 1113, 0x00 }, { 1114, 0x00 }, { 1115, 0x00 },
420 	{ 1116, 0x00 }, { 1117, 0x00 }, { 1118, 0x00 }, { 1119, 0x00 },
421 	{ 1120, 0x00 }, { 1121, 0x00 }, { 1122, 0x00 }, { 1123, 0x00 },
422 	{ 1124, 0x00 }, { 1125, 0x00 }, { 1126, 0x00 }, { 1127, 0x00 },
423 	{ 1128, 0x00 }, { 1129, 0x00 }, { 1130, 0x00 }, { 1131, 0x00 },
424 	{ 1132, 0x00 }, { 1133, 0x00 }, { 1134, 0x00 }, { 1135, 0x00 },
425 	{ 1136, 0x00 }, { 1137, 0x00 }, { 1138, 0x00 }, { 1139, 0x00 },
426 	{ 1140, 0x00 }, { 1141, 0x00 }, { 1142, 0x00 }, { 1143, 0x00 },
427 	{ 1144, 0x00 }, { 1145, 0x00 }, { 1146, 0x00 }, { 1147, 0x00 },
428 	{ 1148, 0x00 }, { 1149, 0x00 }, { 1150, 0x00 }, { 1151, 0x00 },
429 };
430 
adc3xxx_volatile_reg(struct device * dev,unsigned int reg)431 static bool adc3xxx_volatile_reg(struct device *dev, unsigned int reg)
432 {
433 	switch (reg) {
434 	case ADC3XXX_RESET:
435 		return true;
436 	default:
437 		return false;
438 	}
439 }
440 
441 static const struct regmap_range_cfg adc3xxx_ranges[] = {
442 	{
443 		.range_min = 0,
444 		.range_max = 5 * ADC3XXX_PAGE_SIZE,
445 		.selector_reg = ADC3XXX_PAGE_SELECT,
446 		.selector_mask = 0xff,
447 		.selector_shift = 0,
448 		.window_start = 0,
449 		.window_len = ADC3XXX_PAGE_SIZE,
450 	}
451 };
452 
453 static const struct regmap_config adc3xxx_regmap = {
454 	.reg_bits = 8,
455 	.val_bits = 8,
456 
457 	.reg_defaults = adc3xxx_defaults,
458 	.num_reg_defaults = ARRAY_SIZE(adc3xxx_defaults),
459 
460 	.volatile_reg = adc3xxx_volatile_reg,
461 
462 	.cache_type = REGCACHE_RBTREE,
463 
464 	.ranges = adc3xxx_ranges,
465 	.num_ranges = ARRAY_SIZE(adc3xxx_ranges),
466 	.max_register = 5 * ADC3XXX_PAGE_SIZE,
467 };
468 
469 struct adc3xxx_rate_divs {
470 	u32 mclk;
471 	u32 rate;
472 	u8 pll_p;
473 	u8 pll_r;
474 	u8 pll_j;
475 	u16 pll_d;
476 	u8 nadc;
477 	u8 madc;
478 	u8 aosr;
479 };
480 
481 /*
482  * PLL and Clock settings.
483  * If p member is 0, PLL is not used.
484  * The order of the entries in this table have the PLL entries before
485  * the non-PLL entries, so that the PLL modes are preferred unless
486  * the PLL mode setting says otherwise.
487  */
488 static const struct adc3xxx_rate_divs adc3xxx_divs[] = {
489 	/* mclk, rate, p, r, j, d, nadc, madc, aosr */
490 	/* 8k rate */
491 	{ 12000000, 8000, 1, 1, 7, 1680, 42, 2, 128 },
492 	{ 12288000, 8000, 1, 1, 7, 0000, 42, 2, 128 },
493 	/* 11.025k rate */
494 	{ 12000000, 11025, 1, 1, 6, 8208, 29, 2, 128 },
495 	/* 16k rate */
496 	{ 12000000, 16000, 1, 1, 7, 1680, 21, 2, 128 },
497 	{ 12288000, 16000, 1, 1, 7, 0000, 21, 2, 128 },
498 	/* 22.05k rate */
499 	{ 12000000, 22050, 1, 1, 7, 560, 15, 2, 128 },
500 	/* 32k rate */
501 	{ 12000000, 32000, 1, 1, 8, 1920, 12, 2, 128 },
502 	{ 12288000, 32000, 1, 1, 8, 0000, 12, 2, 128 },
503 	/* 44.1k rate */
504 	{ 12000000, 44100, 1, 1, 7, 5264, 8, 2, 128 },
505 	/* 48k rate */
506 	{ 12000000, 48000, 1, 1, 7, 1680, 7, 2, 128 },
507 	{ 12288000, 48000, 1, 1, 7, 0000, 7, 2, 128 },
508 	{ 24576000, 48000, 1, 1, 3, 5000, 7, 2, 128 }, /* With PLL */
509 	{ 24576000, 48000, 0, 0, 0, 0000, 2, 2, 128 }, /* Without PLL */
510 	/* 88.2k rate */
511 	{ 12000000, 88200, 1, 1, 7, 5264, 4, 4, 64 },
512 	/* 96k rate */
513 	{ 12000000, 96000, 1, 1, 8, 1920, 4, 4, 64 },
514 };
515 
adc3xxx_get_divs(struct device * dev,int mclk,int rate,int pll_mode)516 static int adc3xxx_get_divs(struct device *dev, int mclk, int rate, int pll_mode)
517 {
518 	int i;
519 
520 	dev_dbg(dev, "mclk = %d, rate = %d, clock mode %u\n",
521 		mclk, rate, pll_mode);
522 	for (i = 0; i < ARRAY_SIZE(adc3xxx_divs); i++) {
523 		const struct adc3xxx_rate_divs *mode = &adc3xxx_divs[i];
524 
525 		/* Skip this entry if it doesn't fulfill the intended clock
526 		 * mode requirement. We consider anything besides the two
527 		 * modes below to be the same as ADC3XXX_PLL_AUTO.
528 		 */
529 		if ((pll_mode == ADC3XXX_PLL_BYPASS && mode->pll_p) ||
530 		    (pll_mode == ADC3XXX_PLL_ENABLE && !mode->pll_p))
531 			continue;
532 
533 		if (mode->rate == rate && mode->mclk == mclk)
534 			return i;
535 	}
536 
537 	dev_info(dev, "Master clock rate %d and sample rate %d is not supported\n",
538 		 mclk, rate);
539 	return -EINVAL;
540 }
541 
adc3xxx_pll_delay(struct snd_soc_dapm_widget * w,struct snd_kcontrol * kcontrol,int event)542 static int adc3xxx_pll_delay(struct snd_soc_dapm_widget *w,
543 			     struct snd_kcontrol *kcontrol, int event)
544 {
545 	/* 10msec delay needed after PLL power-up to allow
546 	 * PLL and dividers to stabilize (datasheet p13).
547 	 */
548 	usleep_range(10000, 20000);
549 
550 	return 0;
551 }
552 
adc3xxx_coefficient_info(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_info * uinfo)553 static int adc3xxx_coefficient_info(struct snd_kcontrol *kcontrol,
554 				    struct snd_ctl_elem_info *uinfo)
555 {
556 	int numcoeff = kcontrol->private_value >> 16;
557 
558 	uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
559 	uinfo->count = numcoeff;
560 	uinfo->value.integer.min = 0;
561 	uinfo->value.integer.max = 0xffff; /* all coefficients are 16 bit */
562 	return 0;
563 }
564 
adc3xxx_coefficient_get(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)565 static int adc3xxx_coefficient_get(struct snd_kcontrol *kcontrol,
566 				   struct snd_ctl_elem_value *ucontrol)
567 {
568 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
569 	int numcoeff  = kcontrol->private_value >> 16;
570 	int reg = kcontrol->private_value & 0xffff;
571 	int index = 0;
572 
573 	for (index = 0; index < numcoeff; index++) {
574 		unsigned int value_msb, value_lsb, value;
575 
576 		value_msb = snd_soc_component_read(component, reg++);
577 		if ((int)value_msb < 0)
578 			return (int)value_msb;
579 
580 		value_lsb = snd_soc_component_read(component, reg++);
581 		if ((int)value_lsb < 0)
582 			return (int)value_lsb;
583 
584 		value = (value_msb << 8) | value_lsb;
585 		ucontrol->value.integer.value[index] = value;
586 	}
587 
588 	return 0;
589 }
590 
adc3xxx_coefficient_put(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)591 static int adc3xxx_coefficient_put(struct snd_kcontrol *kcontrol,
592 				   struct snd_ctl_elem_value *ucontrol)
593 {
594 	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
595 	int numcoeff  = kcontrol->private_value >> 16;
596 	int reg = kcontrol->private_value & 0xffff;
597 	int index = 0;
598 	int ret;
599 
600 	for (index = 0; index < numcoeff; index++) {
601 		unsigned int value = ucontrol->value.integer.value[index];
602 		unsigned int value_msb = (value >> 8) & 0xff;
603 		unsigned int value_lsb = value & 0xff;
604 
605 		ret = snd_soc_component_write(component, reg++, value_msb);
606 		if (ret)
607 			return ret;
608 
609 		ret = snd_soc_component_write(component, reg++, value_lsb);
610 		if (ret)
611 			return ret;
612 	}
613 
614 	return 0;
615 }
616 
617 /* All on-chip filters have coefficients which are expressed in terms of
618  * 16 bit values, so represent them as strings of 16-bit integers.
619  */
620 #define TI_COEFFICIENTS(xname, reg, numcoeffs) { \
621 	.iface = SNDRV_CTL_ELEM_IFACE_MIXER, \
622 	.name = xname, \
623 	.info = adc3xxx_coefficient_info, \
624 	.get = adc3xxx_coefficient_get,\
625 	.put = adc3xxx_coefficient_put, \
626 	.access = SNDRV_CTL_ELEM_ACCESS_READWRITE, \
627 	.private_value = reg | (numcoeffs << 16) \
628 }
629 
630 static const char * const adc_softstepping_text[] = { "1 step", "2 step", "off" };
631 static SOC_ENUM_SINGLE_DECL(adc_softstepping_enum, ADC3XXX_ADC_DIGITAL, 0,
632 			    adc_softstepping_text);
633 
634 static const char * const multiplier_text[] = { "1", "2", "4", "8", "16", "32", "64", "128" };
635 static SOC_ENUM_SINGLE_DECL(left_agc_attack_mult_enum,
636 			    ADC3XXX_LEFT_CHN_AGC_4, 0, multiplier_text);
637 static SOC_ENUM_SINGLE_DECL(right_agc_attack_mult_enum,
638 			    ADC3XXX_RIGHT_CHN_AGC_4, 0, multiplier_text);
639 static SOC_ENUM_SINGLE_DECL(left_agc_decay_mult_enum,
640 			    ADC3XXX_LEFT_CHN_AGC_5, 0, multiplier_text);
641 static SOC_ENUM_SINGLE_DECL(right_agc_decay_mult_enum,
642 			    ADC3XXX_RIGHT_CHN_AGC_5, 0, multiplier_text);
643 
644 static const char * const dither_dc_offset_text[] = {
645 	"0mV", "15mV", "30mV", "45mV", "60mV", "75mV", "90mV", "105mV",
646 	"-15mV", "-30mV", "-45mV", "-60mV", "-75mV", "-90mV", "-105mV"
647 };
648 static const unsigned int dither_dc_offset_values[] = {
649 	0, 1, 2, 3, 4, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15
650 };
651 static SOC_VALUE_ENUM_DOUBLE_DECL(dither_dc_offset_enum,
652 				  ADC3XXX_DITHER_CTRL,
653 				  4, 0, 0xf, dither_dc_offset_text,
654 				  dither_dc_offset_values);
655 
656 static const DECLARE_TLV_DB_SCALE(pga_tlv, 0, 50, 0);
657 static const DECLARE_TLV_DB_SCALE(adc_tlv, -1200, 50, 0);
658 static const DECLARE_TLV_DB_SCALE(adc_fine_tlv, -40, 10, 0);
659 /* AGC target: 8 values: -5.5, -8, -10, -12, -14, -17, -20, -24 dB */
660 /* It would be nice to declare these in the order above, but empirically
661  * TLV_DB_SCALE_ITEM doesn't take lightly to the increment (second) parameter
662  * being negative, despite there being examples to the contrary in other
663  * drivers. So declare these in the order from lowest to highest, and
664  * set the invert flag in the SOC_DOUBLE_R_TLV declaration instead.
665  */
666 static const DECLARE_TLV_DB_RANGE(agc_target_tlv,
667 	0, 0, TLV_DB_SCALE_ITEM(-2400, 0, 0),
668 	1, 3, TLV_DB_SCALE_ITEM(-2000, 300, 0),
669 	4, 6, TLV_DB_SCALE_ITEM(-1200, 200, 0),
670 	7, 7, TLV_DB_SCALE_ITEM(-550, 0, 0));
671 /* Since the 'disabled' value (mute) is at the highest value in the dB
672  * range (i.e. just before -32 dB) rather than the lowest, we need to resort
673  * to using a TLV_DB_RANGE in order to get the mute value in the right place.
674  */
675 static const DECLARE_TLV_DB_RANGE(agc_thresh_tlv,
676 	0, 30, TLV_DB_SCALE_ITEM(-9000, 200, 0),
677 	31, 31, TLV_DB_SCALE_ITEM(0, 0, 1)); /* disabled = mute */
678 /* AGC hysteresis: 4 values: 1, 2, 4 dB, disabled (= mute) */
679 static const DECLARE_TLV_DB_RANGE(agc_hysteresis_tlv,
680 	0, 1, TLV_DB_SCALE_ITEM(100, 100, 0),
681 	2, 2, TLV_DB_SCALE_ITEM(400, 0, 0),
682 	3, 3, TLV_DB_SCALE_ITEM(0, 0, 1)); /* disabled = mute */
683 static const DECLARE_TLV_DB_SCALE(agc_max_tlv, 0, 50, 0);
684 /* Input attenuation: -6 dB or 0 dB */
685 static const DECLARE_TLV_DB_SCALE(input_attenuation_tlv, -600, 600, 0);
686 
687 static const struct snd_kcontrol_new adc3xxx_snd_controls[] = {
688 	SOC_DOUBLE_R_TLV("PGA Capture Volume", ADC3XXX_LEFT_APGA_CTRL,
689 			 ADC3XXX_RIGHT_APGA_CTRL, 0, 80, 0, pga_tlv),
690 	SOC_DOUBLE("PGA Capture Switch", ADC3XXX_ADC_FGA, 7, 3, 1, 1),
691 	SOC_DOUBLE_R("AGC Capture Switch", ADC3XXX_LEFT_CHN_AGC_1,
692 		     ADC3XXX_RIGHT_CHN_AGC_1, 7, 1, 0),
693 	SOC_DOUBLE_R_TLV("AGC Target Level Capture Volume", ADC3XXX_LEFT_CHN_AGC_1,
694 		     ADC3XXX_RIGHT_CHN_AGC_2, 4, 0x07, 1, agc_target_tlv),
695 	SOC_DOUBLE_R_TLV("AGC Noise Threshold Capture Volume", ADC3XXX_LEFT_CHN_AGC_2,
696 		     ADC3XXX_RIGHT_CHN_AGC_2, 1, 0x1f, 1, agc_thresh_tlv),
697 	SOC_DOUBLE_R_TLV("AGC Hysteresis Capture Volume", ADC3XXX_LEFT_CHN_AGC_2,
698 		     ADC3XXX_RIGHT_CHN_AGC_2, 6, 3, 0, agc_hysteresis_tlv),
699 	SOC_DOUBLE_R("AGC Clip Stepping Capture Switch", ADC3XXX_LEFT_CHN_AGC_2,
700 		     ADC3XXX_RIGHT_CHN_AGC_2, 0, 1, 0),
701 	/*
702 	 * Oddly enough, the data sheet says the default value
703 	 * for the left/right AGC maximum gain register field
704 	 * (ADC3XXX_LEFT/RIGHT_CHN_AGC_3 bits 0..6) is 0x7f = 127
705 	 * (verified empirically) even though this value (indeed, above
706 	 * 0x50) is specified as 'Reserved. Do not use.' in the accompanying
707 	 * table in the data sheet.
708 	 */
709 	SOC_DOUBLE_R_TLV("AGC Maximum Capture Volume", ADC3XXX_LEFT_CHN_AGC_3,
710 		     ADC3XXX_RIGHT_CHN_AGC_3, 0, 0x50, 0, agc_max_tlv),
711 	SOC_DOUBLE_R("AGC Attack Time", ADC3XXX_LEFT_CHN_AGC_4,
712 		     ADC3XXX_RIGHT_CHN_AGC_4, 3, 0x1f, 0),
713 	/* Would like to have the multipliers as LR pairs, but there is
714 	 * no SOC_ENUM_foo which accepts two values in separate registers.
715 	 */
716 	SOC_ENUM("AGC Left Attack Time Multiplier", left_agc_attack_mult_enum),
717 	SOC_ENUM("AGC Right Attack Time Multiplier", right_agc_attack_mult_enum),
718 	SOC_DOUBLE_R("AGC Decay Time", ADC3XXX_LEFT_CHN_AGC_5,
719 		     ADC3XXX_RIGHT_CHN_AGC_5, 3, 0x1f, 0),
720 	SOC_ENUM("AGC Left Decay Time Multiplier", left_agc_decay_mult_enum),
721 	SOC_ENUM("AGC Right Decay Time Multiplier", right_agc_decay_mult_enum),
722 	SOC_DOUBLE_R("AGC Noise Debounce", ADC3XXX_LEFT_CHN_AGC_6,
723 		     ADC3XXX_RIGHT_CHN_AGC_6, 0, 0x1f, 0),
724 	SOC_DOUBLE_R("AGC Signal Debounce", ADC3XXX_LEFT_CHN_AGC_7,
725 		     ADC3XXX_RIGHT_CHN_AGC_7, 0, 0x0f, 0),
726 	/* Read only register */
727 	SOC_DOUBLE_R_S_TLV("AGC Applied Capture Volume", ADC3XXX_LEFT_AGC_GAIN,
728 			   ADC3XXX_RIGHT_AGC_GAIN, 0, -24, 40, 6, 0, adc_tlv),
729 	/* ADC soft stepping */
730 	SOC_ENUM("ADC Soft Stepping", adc_softstepping_enum),
731 	/* Left/Right Input attenuation */
732 	SOC_SINGLE_TLV("Left Input IN_1L Capture Volume",
733 		       ADC3XXX_LEFT_PGA_SEL_1, 0, 1, 1, input_attenuation_tlv),
734 	SOC_SINGLE_TLV("Left Input IN_2L Capture Volume",
735 		       ADC3XXX_LEFT_PGA_SEL_1, 2, 1, 1, input_attenuation_tlv),
736 	SOC_SINGLE_TLV("Left Input IN_3L Capture Volume",
737 		       ADC3XXX_LEFT_PGA_SEL_1, 4, 1, 1, input_attenuation_tlv),
738 	SOC_SINGLE_TLV("Left Input IN_1R Capture Volume",
739 		       ADC3XXX_LEFT_PGA_SEL_2, 0, 1, 1, input_attenuation_tlv),
740 	SOC_SINGLE_TLV("Left Input DIF_2L_3L Capture Volume",
741 		       ADC3XXX_LEFT_PGA_SEL_1, 6, 1, 1, input_attenuation_tlv),
742 	SOC_SINGLE_TLV("Left Input DIF_1L_1R Capture Volume",
743 		       ADC3XXX_LEFT_PGA_SEL_2, 4, 1, 1, input_attenuation_tlv),
744 	SOC_SINGLE_TLV("Left Input DIF_2R_3R Capture Volume",
745 		       ADC3XXX_LEFT_PGA_SEL_2, 2, 1, 1, input_attenuation_tlv),
746 	SOC_SINGLE_TLV("Right Input IN_1R Capture Volume",
747 		       ADC3XXX_RIGHT_PGA_SEL_1, 0, 1, 1, input_attenuation_tlv),
748 	SOC_SINGLE_TLV("Right Input IN_2R Capture Volume",
749 		       ADC3XXX_RIGHT_PGA_SEL_1, 2, 1, 1, input_attenuation_tlv),
750 	SOC_SINGLE_TLV("Right Input IN_3R Capture Volume",
751 		       ADC3XXX_RIGHT_PGA_SEL_1, 4, 1, 1, input_attenuation_tlv),
752 	SOC_SINGLE_TLV("Right Input IN_1L Capture Volume",
753 		       ADC3XXX_RIGHT_PGA_SEL_2, 0, 1, 1, input_attenuation_tlv),
754 	SOC_SINGLE_TLV("Right Input DIF_2R_3R Capture Volume",
755 		       ADC3XXX_RIGHT_PGA_SEL_1, 6, 1, 1, input_attenuation_tlv),
756 	SOC_SINGLE_TLV("Right Input DIF_1L_1R Capture Volume",
757 		       ADC3XXX_RIGHT_PGA_SEL_2, 4, 1, 1, input_attenuation_tlv),
758 	SOC_SINGLE_TLV("Right Input DIF_2L_3L Capture Volume",
759 		       ADC3XXX_RIGHT_PGA_SEL_2, 2, 1, 1, input_attenuation_tlv),
760 	SOC_DOUBLE_R_S_TLV("ADC Volume Control Capture Volume", ADC3XXX_LADC_VOL,
761 			   ADC3XXX_RADC_VOL, 0, -24, 40, 6, 0, adc_tlv),
762 	/* Empirically, the following doesn't work the way it's supposed
763 	 * to. Values 0, -0.1, -0.2 and -0.3 dB result in the same level, and
764 	 * -0.4 dB drops about 0.12 dB on a specific chip.
765 	 */
766 	SOC_DOUBLE_TLV("ADC Fine Volume Control Capture Volume", ADC3XXX_ADC_FGA,
767 		       4, 0, 4, 1, adc_fine_tlv),
768 	SOC_SINGLE("Left ADC Unselected CM Bias Capture Switch",
769 		   ADC3XXX_LEFT_PGA_SEL_2, 6, 1, 0),
770 	SOC_SINGLE("Right ADC Unselected CM Bias Capture Switch",
771 		   ADC3XXX_RIGHT_PGA_SEL_2, 6, 1, 0),
772 	SOC_ENUM("Dither Control DC Offset", dither_dc_offset_enum),
773 
774 	/* Coefficient memory for miniDSP. */
775 	/* For the default PRB_R1 processing block, the only available
776 	 * filter is the first order IIR.
777 	 */
778 
779 	TI_COEFFICIENTS("Left ADC IIR Coefficients N0 N1 D1",
780 			ADC3XXX_LEFT_ADC_IIR_COEFF_N0_MSB, 3),
781 
782 	TI_COEFFICIENTS("Right ADC IIR Coefficients N0 N1 D1",
783 			ADC3XXX_RIGHT_ADC_IIR_COEFF_N0_MSB, 3),
784 };
785 
786 /* Left input selection, Single Ended inputs and Differential inputs */
787 static const struct snd_kcontrol_new left_input_mixer_controls[] = {
788 	SOC_DAPM_SINGLE("IN_1L Capture Switch",
789 			ADC3XXX_LEFT_PGA_SEL_1, 1, 0x1, 1),
790 	SOC_DAPM_SINGLE("IN_2L Capture Switch",
791 			ADC3XXX_LEFT_PGA_SEL_1, 3, 0x1, 1),
792 	SOC_DAPM_SINGLE("IN_3L Capture Switch",
793 			ADC3XXX_LEFT_PGA_SEL_1, 5, 0x1, 1),
794 	SOC_DAPM_SINGLE("DIF_2L_3L Capture Switch",
795 			ADC3XXX_LEFT_PGA_SEL_1, 7, 0x1, 1),
796 	SOC_DAPM_SINGLE("DIF_1L_1R Capture Switch",
797 			ADC3XXX_LEFT_PGA_SEL_2, 5, 0x1, 1),
798 	SOC_DAPM_SINGLE("DIF_2R_3R Capture Switch",
799 			ADC3XXX_LEFT_PGA_SEL_2, 3, 0x1, 1),
800 	SOC_DAPM_SINGLE("IN_1R Capture Switch",
801 			ADC3XXX_LEFT_PGA_SEL_2, 1, 0x1, 1),
802 };
803 
804 /* Right input selection, Single Ended inputs and Differential inputs */
805 static const struct snd_kcontrol_new right_input_mixer_controls[] = {
806 	SOC_DAPM_SINGLE("IN_1R Capture Switch",
807 			ADC3XXX_RIGHT_PGA_SEL_1, 1, 0x1, 1),
808 	SOC_DAPM_SINGLE("IN_2R Capture Switch",
809 			ADC3XXX_RIGHT_PGA_SEL_1, 3, 0x1, 1),
810 	SOC_DAPM_SINGLE("IN_3R Capture Switch",
811 			 ADC3XXX_RIGHT_PGA_SEL_1, 5, 0x1, 1),
812 	SOC_DAPM_SINGLE("DIF_2R_3R Capture Switch",
813 			 ADC3XXX_RIGHT_PGA_SEL_1, 7, 0x1, 1),
814 	SOC_DAPM_SINGLE("DIF_1L_1R Capture Switch",
815 			 ADC3XXX_RIGHT_PGA_SEL_2, 5, 0x1, 1),
816 	SOC_DAPM_SINGLE("DIF_2L_3L Capture Switch",
817 			 ADC3XXX_RIGHT_PGA_SEL_2, 3, 0x1, 1),
818 	SOC_DAPM_SINGLE("IN_1L Capture Switch",
819 			 ADC3XXX_RIGHT_PGA_SEL_2, 1, 0x1, 1),
820 };
821 
822 /* Left Digital Mic input for left ADC */
823 static const struct snd_kcontrol_new left_input_dmic_controls[] = {
824 	SOC_DAPM_SINGLE("Left ADC Capture Switch",
825 			ADC3XXX_ADC_DIGITAL, 3, 0x1, 0),
826 };
827 
828 /* Right Digital Mic input for Right ADC */
829 static const struct snd_kcontrol_new right_input_dmic_controls[] = {
830 	SOC_DAPM_SINGLE("Right ADC Capture Switch",
831 			ADC3XXX_ADC_DIGITAL, 2, 0x1, 0),
832 };
833 
834 /* DAPM widgets */
835 static const struct snd_soc_dapm_widget adc3xxx_dapm_widgets[] = {
836 
837 	/* Left Input Selection */
838 	SND_SOC_DAPM_MIXER("Left Input", SND_SOC_NOPM, 0, 0,
839 			   &left_input_mixer_controls[0],
840 			   ARRAY_SIZE(left_input_mixer_controls)),
841 	/* Right Input Selection */
842 	SND_SOC_DAPM_MIXER("Right Input", SND_SOC_NOPM, 0, 0,
843 			   &right_input_mixer_controls[0],
844 			   ARRAY_SIZE(right_input_mixer_controls)),
845 	/* PGA selection */
846 	SND_SOC_DAPM_PGA("Left PGA", ADC3XXX_LEFT_APGA_CTRL, 7, 1, NULL, 0),
847 	SND_SOC_DAPM_PGA("Right PGA", ADC3XXX_RIGHT_APGA_CTRL, 7, 1, NULL, 0),
848 
849 	/* Digital Microphone Input Control for Left/Right ADC */
850 	SND_SOC_DAPM_MIXER("Left DMic Input", SND_SOC_NOPM, 0, 0,
851 			&left_input_dmic_controls[0],
852 			ARRAY_SIZE(left_input_dmic_controls)),
853 	SND_SOC_DAPM_MIXER("Right DMic Input", SND_SOC_NOPM, 0, 0,
854 			&right_input_dmic_controls[0],
855 			ARRAY_SIZE(right_input_dmic_controls)),
856 
857 	/* Left/Right ADC */
858 	SND_SOC_DAPM_ADC("Left ADC", "Left Capture", ADC3XXX_ADC_DIGITAL, 7, 0),
859 	SND_SOC_DAPM_ADC("Right ADC", "Right Capture", ADC3XXX_ADC_DIGITAL, 6, 0),
860 
861 	/* Inputs */
862 	SND_SOC_DAPM_INPUT("IN_1L"),
863 	SND_SOC_DAPM_INPUT("IN_1R"),
864 	SND_SOC_DAPM_INPUT("IN_2L"),
865 	SND_SOC_DAPM_INPUT("IN_2R"),
866 	SND_SOC_DAPM_INPUT("IN_3L"),
867 	SND_SOC_DAPM_INPUT("IN_3R"),
868 	SND_SOC_DAPM_INPUT("DIFL_1L_1R"),
869 	SND_SOC_DAPM_INPUT("DIFL_2L_3L"),
870 	SND_SOC_DAPM_INPUT("DIFL_2R_3R"),
871 	SND_SOC_DAPM_INPUT("DIFR_1L_1R"),
872 	SND_SOC_DAPM_INPUT("DIFR_2L_3L"),
873 	SND_SOC_DAPM_INPUT("DIFR_2R_3R"),
874 	SND_SOC_DAPM_INPUT("DMic_L"),
875 	SND_SOC_DAPM_INPUT("DMic_R"),
876 
877 	/* Digital audio interface output */
878 	SND_SOC_DAPM_AIF_OUT("AIF_OUT", "Capture", 0, SND_SOC_NOPM, 0, 0),
879 
880 	/* Clocks */
881 	SND_SOC_DAPM_SUPPLY("PLL_CLK", ADC3XXX_PLL_PROG_PR, ADC3XXX_ENABLE_PLL_SHIFT,
882 			    0, adc3xxx_pll_delay, SND_SOC_DAPM_POST_PMU),
883 
884 	SND_SOC_DAPM_SUPPLY("ADC_CLK", ADC3XXX_ADC_NADC, ADC3XXX_ENABLE_NADC_SHIFT,
885 			    0, NULL, 0),
886 	SND_SOC_DAPM_SUPPLY("ADC_MOD_CLK", ADC3XXX_ADC_MADC, ADC3XXX_ENABLE_MADC_SHIFT,
887 			    0, NULL, 0),
888 
889 	/* This refers to the generated BCLK in master mode. */
890 	SND_SOC_DAPM_SUPPLY("BCLK", ADC3XXX_BCLK_N_DIV, ADC3XXX_ENABLE_BCLK_SHIFT,
891 			    0, NULL, 0),
892 };
893 
894 static const struct snd_soc_dapm_route adc3xxx_intercon[] = {
895 	/* Left input selection from switches */
896 	{ "Left Input", "IN_1L Capture Switch", "IN_1L" },
897 	{ "Left Input", "IN_2L Capture Switch", "IN_2L" },
898 	{ "Left Input", "IN_3L Capture Switch", "IN_3L" },
899 	{ "Left Input", "DIF_2L_3L Capture Switch", "DIFL_2L_3L" },
900 	{ "Left Input", "DIF_1L_1R Capture Switch", "DIFL_1L_1R" },
901 	{ "Left Input", "DIF_2R_3R Capture Switch", "DIFL_2R_3R" },
902 	{ "Left Input", "IN_1R Capture Switch", "IN_1R" },
903 
904 	/* Left input selection to left PGA */
905 	{ "Left PGA", NULL, "Left Input" },
906 
907 	/* Left PGA to left ADC */
908 	{ "Left ADC", NULL, "Left PGA" },
909 
910 	/* Right input selection from switches */
911 	{ "Right Input", "IN_1R Capture Switch", "IN_1R" },
912 	{ "Right Input", "IN_2R Capture Switch", "IN_2R" },
913 	{ "Right Input", "IN_3R Capture Switch", "IN_3R" },
914 	{ "Right Input", "DIF_2R_3R Capture Switch", "DIFR_2R_3R" },
915 	{ "Right Input", "DIF_1L_1R Capture Switch", "DIFR_1L_1R" },
916 	{ "Right Input", "DIF_2L_3L Capture Switch", "DIFR_2L_3L" },
917 	{ "Right Input", "IN_1L Capture Switch", "IN_1L" },
918 
919 	/* Right input selection to right PGA */
920 	{ "Right PGA", NULL, "Right Input" },
921 
922 	/* Right PGA to right ADC */
923 	{ "Right ADC", NULL, "Right PGA" },
924 
925 	/* Left DMic Input selection from switch */
926 	{ "Left DMic Input", "Left ADC Capture Switch", "DMic_L" },
927 
928 	/* Left DMic to left ADC */
929 	{ "Left ADC", NULL, "Left DMic Input" },
930 
931 	/* Right DMic Input selection from switch */
932 	{ "Right DMic Input", "Right ADC Capture Switch", "DMic_R" },
933 
934 	/* Right DMic to right ADC */
935 	{ "Right ADC", NULL, "Right DMic Input" },
936 
937 	/* ADC to AIF output */
938 	{ "AIF_OUT", NULL, "Left ADC" },
939 	{ "AIF_OUT", NULL, "Right ADC" },
940 
941 	/* Clocking */
942 	{ "ADC_MOD_CLK", NULL, "ADC_CLK" },
943 	{ "Left ADC", NULL, "ADC_MOD_CLK" },
944 	{ "Right ADC", NULL, "ADC_MOD_CLK" },
945 
946 	{ "BCLK", NULL, "ADC_CLK" },
947 };
948 
949 static const struct snd_soc_dapm_route adc3xxx_pll_intercon[] = {
950 	{ "ADC_CLK", NULL, "PLL_CLK" },
951 };
952 
953 static const struct snd_soc_dapm_route adc3xxx_bclk_out_intercon[] = {
954 	{ "AIF_OUT", NULL, "BCLK" }
955 };
956 
adc3xxx_gpio_request(struct gpio_chip * chip,unsigned int offset)957 static int adc3xxx_gpio_request(struct gpio_chip *chip, unsigned int offset)
958 {
959 	struct adc3xxx *adc3xxx = gpiochip_get_data(chip);
960 
961 	if (offset >= ADC3XXX_GPIOS_MAX)
962 		return -EINVAL;
963 
964 	if (offset >= 0 && offset < ADC3XXX_GPIO_PINS) {
965 		/* GPIO1 is offset 0, GPIO2 is offset 1 */
966 		/* We check here that the GPIO pins are either not configured
967 		 * in the DT, or that they purposely are set as outputs.
968 		 * (Input mode not yet implemented).
969 		 */
970 		if (adc3xxx->gpio_cfg[offset] != 0 &&
971 		    adc3xxx->gpio_cfg[offset] != ADC3XXX_GPIO_GPO + 1)
972 			return -EINVAL;
973 	} else if (offset >= ADC3XXX_GPIO_PINS && offset < ADC3XXX_GPIOS_MAX) {
974 		/* MICBIAS1 is offset 2, MICBIAS2 is offset 3 */
975 		/* We check here if the MICBIAS pins are in fact configured
976 		 * as GPOs.
977 		 */
978 		if (!adc3xxx->micbias_gpo[offset - ADC3XXX_GPIO_PINS])
979 			return -EINVAL;
980 	}
981 
982 	return 0;
983 }
984 
adc3xxx_gpio_direction_out(struct gpio_chip * chip,unsigned int offset,int value)985 static int adc3xxx_gpio_direction_out(struct gpio_chip *chip,
986 				      unsigned int offset, int value)
987 {
988 	struct adc3xxx *adc3xxx = gpiochip_get_data(chip);
989 
990 	/* For the MICBIAS pins, they are by definition outputs. */
991 	if (offset >= ADC3XXX_GPIO_PINS) {
992 		unsigned int vg;
993 		unsigned int micbias = offset - ADC3XXX_GPIO_PINS;
994 
995 		if (value)
996 			vg = adc3xxx->micbias_vg[micbias];
997 		else
998 			vg = ADC3XXX_MICBIAS_OFF;
999 		return regmap_update_bits(adc3xxx->regmap,
1000 					   ADC3XXX_MICBIAS_CTRL,
1001 					   ADC3XXX_MICBIAS_MASK << adc3xxx_micbias_shift[micbias],
1002 					   vg << adc3xxx_micbias_shift[micbias]);
1003 	}
1004 
1005 	/* Set GPIO output function. */
1006 	return regmap_update_bits(adc3xxx->regmap,
1007 				  adc3xxx_gpio_ctrl_reg[offset],
1008 				  ADC3XXX_GPIO_CTRL_CFG_MASK |
1009 				  ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK,
1010 				  ADC3XXX_GPIO_GPO << ADC3XXX_GPIO_CTRL_CFG_SHIFT |
1011 				  !!value << ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_SHIFT);
1012 }
1013 
1014 /* With only GPIO outputs configured, we never get the .direction_out call,
1015  * so we set the output mode and output value in the same call. Hence
1016  * .set in practice does the same thing as .direction_out .
1017  */
adc3xxx_gpio_set(struct gpio_chip * chip,unsigned int offset,int value)1018 static void adc3xxx_gpio_set(struct gpio_chip *chip, unsigned int offset,
1019 			     int value)
1020 {
1021 	(void) adc3xxx_gpio_direction_out(chip, offset, value);
1022 }
1023 
1024 /* Even though we only support GPIO output for now, some GPIO clients
1025  * want to read the current pin state using the .get callback.
1026  */
adc3xxx_gpio_get(struct gpio_chip * chip,unsigned int offset)1027 static int adc3xxx_gpio_get(struct gpio_chip *chip, unsigned int offset)
1028 {
1029 	struct adc3xxx *adc3xxx = gpiochip_get_data(chip);
1030 	unsigned int regval;
1031 	int ret;
1032 
1033 	/* We only allow output pins, so just read the value prevously set. */
1034 	if (offset >= ADC3XXX_GPIO_PINS) {
1035 		/* MICBIAS pins */
1036 		unsigned int micbias = offset - ADC3XXX_GPIO_PINS;
1037 
1038 		ret = regmap_read(adc3xxx->regmap, ADC3XXX_MICBIAS_CTRL, &regval);
1039 		if (ret)
1040 			return ret;
1041 		return ((regval >> adc3xxx_micbias_shift[micbias]) & ADC3XXX_MICBIAS_MASK) !=
1042 		       ADC3XXX_MICBIAS_OFF;
1043 	}
1044 	ret = regmap_read(adc3xxx->regmap, adc3xxx_gpio_ctrl_reg[offset], &regval);
1045 	if (ret)
1046 		return ret;
1047 	return !!(regval & ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK);
1048 }
1049 
1050 static const struct gpio_chip adc3xxx_gpio_chip = {
1051 	.label			= "adc3xxx",
1052 	.owner			= THIS_MODULE,
1053 	.request		= adc3xxx_gpio_request,
1054 	.direction_output	= adc3xxx_gpio_direction_out,
1055 	.set			= adc3xxx_gpio_set,
1056 	.get			= adc3xxx_gpio_get,
1057 	.can_sleep		= 1,
1058 };
1059 
adc3xxx_free_gpio(struct adc3xxx * adc3xxx)1060 static void adc3xxx_free_gpio(struct adc3xxx *adc3xxx)
1061 {
1062 #ifdef CONFIG_GPIOLIB
1063 	gpiochip_remove(&adc3xxx->gpio_chip);
1064 #endif
1065 }
1066 
adc3xxx_init_gpio(struct adc3xxx * adc3xxx)1067 static void adc3xxx_init_gpio(struct adc3xxx *adc3xxx)
1068 {
1069 	int gpio, micbias;
1070 	int ret;
1071 
1072 	adc3xxx->gpio_chip = adc3xxx_gpio_chip;
1073 	adc3xxx->gpio_chip.ngpio = ADC3XXX_GPIOS_MAX;
1074 	adc3xxx->gpio_chip.parent = adc3xxx->dev;
1075 	adc3xxx->gpio_chip.base = -1;
1076 
1077 	ret = gpiochip_add_data(&adc3xxx->gpio_chip, adc3xxx);
1078 	if (ret)
1079 		dev_err(adc3xxx->dev, "Failed to add gpios: %d\n", ret);
1080 
1081 	/* Set up potential GPIO configuration from the devicetree.
1082 	 * This allows us to set up things which are not software
1083 	 * controllable GPIOs, such as PDM microphone I/O,
1084 	 */
1085 	for (gpio = 0; gpio < ADC3XXX_GPIO_PINS; gpio++) {
1086 		unsigned int cfg = adc3xxx->gpio_cfg[gpio];
1087 
1088 		if (cfg) {
1089 			cfg--; /* actual value to use is stored +1 */
1090 			regmap_update_bits(adc3xxx->regmap,
1091 					   adc3xxx_gpio_ctrl_reg[gpio],
1092 					   ADC3XXX_GPIO_CTRL_CFG_MASK,
1093 					   cfg << ADC3XXX_GPIO_CTRL_CFG_SHIFT);
1094 		}
1095 	}
1096 
1097 	/* Set up micbias voltage. */
1098 	/* If pin is configured as GPO, set off initially. */
1099 	for (micbias = 0; micbias < ADC3XXX_MICBIAS_PINS; micbias++) {
1100 		unsigned int vg;
1101 
1102 		if (adc3xxx->micbias_gpo[micbias])
1103 			vg = ADC3XXX_MICBIAS_OFF;
1104 		else
1105 			vg = adc3xxx->micbias_vg[micbias];
1106 
1107 		regmap_update_bits(adc3xxx->regmap,
1108 				   ADC3XXX_MICBIAS_CTRL,
1109 				   ADC3XXX_MICBIAS_MASK << adc3xxx_micbias_shift[micbias],
1110 				   vg << adc3xxx_micbias_shift[micbias]);
1111 	}
1112 }
1113 
adc3xxx_parse_dt_gpio(struct adc3xxx * adc3xxx,const char * propname,unsigned int * cfg)1114 static int adc3xxx_parse_dt_gpio(struct adc3xxx *adc3xxx,
1115 				 const char *propname, unsigned int *cfg)
1116 {
1117 	struct device *dev = adc3xxx->dev;
1118 	struct device_node *np = dev->of_node;
1119 	unsigned int val;
1120 
1121 	if (!of_property_read_u32(np, propname, &val)) {
1122 		if (val & ~15 || val == 7 || val >= 11) {
1123 			dev_err(dev, "Invalid property value for '%s'\n", propname);
1124 			return -EINVAL;
1125 		}
1126 		if (val == ADC3XXX_GPIO_GPI)
1127 			dev_warn(dev, "GPIO Input read not yet implemented\n");
1128 		*cfg = val + 1; /* 0 => not set up, all others shifted +1 */
1129 	}
1130 	return 0;
1131 }
1132 
adc3xxx_parse_dt_micbias_gpo(struct adc3xxx * adc3xxx,const char * propname,unsigned int * cfg)1133 static int adc3xxx_parse_dt_micbias_gpo(struct adc3xxx *adc3xxx,
1134 					const char *propname,
1135 					unsigned int *cfg)
1136 {
1137 	struct device *dev = adc3xxx->dev;
1138 	struct device_node *np = dev->of_node;
1139 
1140 	*cfg = of_property_read_bool(np, propname);
1141 	return 0;
1142 }
1143 
adc3xxx_parse_dt_micbias_vg(struct adc3xxx * adc3xxx,const char * propname,unsigned int * vg)1144 static int adc3xxx_parse_dt_micbias_vg(struct adc3xxx *adc3xxx,
1145 				       const char *propname, unsigned int *vg)
1146 {
1147 	struct device *dev = adc3xxx->dev;
1148 	struct device_node *np = dev->of_node;
1149 	unsigned int val;
1150 
1151 	if (!of_property_read_u32(np, propname, &val)) {
1152 		if (val > ADC3XXX_MICBIAS_AVDD) {
1153 			dev_err(dev, "Invalid property value for '%s'\n", propname);
1154 			return -EINVAL;
1155 		}
1156 		*vg = val;
1157 	}
1158 	return 0;
1159 }
1160 
adc3xxx_parse_pll_mode(uint32_t val,unsigned int * pll_mode)1161 static int adc3xxx_parse_pll_mode(uint32_t val, unsigned int *pll_mode)
1162 {
1163 	if (val != ADC3XXX_PLL_ENABLE && val != ADC3XXX_PLL_BYPASS &&
1164 	    val != ADC3XXX_PLL_AUTO)
1165 		return -EINVAL;
1166 
1167 	*pll_mode = val;
1168 
1169 	return 0;
1170 }
1171 
adc3xxx_setup_pll(struct snd_soc_component * component,int div_entry)1172 static void adc3xxx_setup_pll(struct snd_soc_component *component,
1173 			      int div_entry)
1174 {
1175 	int i = div_entry;
1176 
1177 	/* P & R values */
1178 	snd_soc_component_write(component, ADC3XXX_PLL_PROG_PR,
1179 				(adc3xxx_divs[i].pll_p << ADC3XXX_PLLP_SHIFT) |
1180 				(adc3xxx_divs[i].pll_r << ADC3XXX_PLLR_SHIFT));
1181 	/* J value */
1182 	snd_soc_component_write(component, ADC3XXX_PLL_PROG_J,
1183 				adc3xxx_divs[i].pll_j & ADC3XXX_PLLJ_MASK);
1184 	/* D value */
1185 	snd_soc_component_write(component, ADC3XXX_PLL_PROG_D_LSB,
1186 				adc3xxx_divs[i].pll_d & ADC3XXX_PLLD_LSB_MASK);
1187 	snd_soc_component_write(component, ADC3XXX_PLL_PROG_D_MSB,
1188 				(adc3xxx_divs[i].pll_d >> 8) & ADC3XXX_PLLD_MSB_MASK);
1189 }
1190 
adc3xxx_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)1191 static int adc3xxx_hw_params(struct snd_pcm_substream *substream,
1192 			     struct snd_pcm_hw_params *params,
1193 			     struct snd_soc_dai *dai)
1194 {
1195 	struct snd_soc_component *component = dai->component;
1196 	struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(dai->component);
1197 	struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component);
1198 	int i, width = 16;
1199 	u8 iface_len, bdiv;
1200 
1201 	i = adc3xxx_get_divs(component->dev, adc3xxx->sysclk,
1202 			     params_rate(params), adc3xxx->pll_mode);
1203 
1204 	if (i < 0)
1205 		return i;
1206 
1207 	/* select data word length */
1208 	switch (params_width(params)) {
1209 	case 16:
1210 		iface_len = ADC3XXX_IFACE_16BITS;
1211 		width = 16;
1212 		break;
1213 	case 20:
1214 		iface_len = ADC3XXX_IFACE_20BITS;
1215 		width = 20;
1216 		break;
1217 	case 24:
1218 		iface_len = ADC3XXX_IFACE_24BITS;
1219 		width = 24;
1220 		break;
1221 	case 32:
1222 		iface_len = ADC3XXX_IFACE_32BITS;
1223 		width = 32;
1224 		break;
1225 	default:
1226 		dev_err(component->dev, "Unsupported serial data format\n");
1227 		return -EINVAL;
1228 	}
1229 	snd_soc_component_update_bits(component, ADC3XXX_INTERFACE_CTRL_1,
1230 				      ADC3XXX_WLENGTH_MASK, iface_len);
1231 	if (adc3xxx_divs[i].pll_p) { /* If PLL used for this mode */
1232 		adc3xxx_setup_pll(component, i);
1233 		snd_soc_component_write(component, ADC3XXX_CLKGEN_MUX, ADC3XXX_USE_PLL);
1234 		if (!adc3xxx->use_pll) {
1235 			snd_soc_dapm_add_routes(dapm, adc3xxx_pll_intercon,
1236 						ARRAY_SIZE(adc3xxx_pll_intercon));
1237 			adc3xxx->use_pll = 1;
1238 		}
1239 	} else {
1240 		snd_soc_component_write(component, ADC3XXX_CLKGEN_MUX, ADC3XXX_NO_PLL);
1241 		if (adc3xxx->use_pll) {
1242 			snd_soc_dapm_del_routes(dapm, adc3xxx_pll_intercon,
1243 						ARRAY_SIZE(adc3xxx_pll_intercon));
1244 			adc3xxx->use_pll = 0;
1245 		}
1246 	}
1247 
1248 	/* NADC */
1249 	snd_soc_component_update_bits(component, ADC3XXX_ADC_NADC,
1250 				      ADC3XXX_NADC_MASK, adc3xxx_divs[i].nadc);
1251 	/* MADC */
1252 	snd_soc_component_update_bits(component, ADC3XXX_ADC_MADC,
1253 				      ADC3XXX_MADC_MASK, adc3xxx_divs[i].madc);
1254 	/* AOSR */
1255 	snd_soc_component_update_bits(component, ADC3XXX_ADC_AOSR,
1256 				      ADC3XXX_AOSR_MASK, adc3xxx_divs[i].aosr);
1257 	/* BDIV N Value */
1258 	/* BCLK is (by default) set up to be derived from ADC_CLK */
1259 	bdiv = (adc3xxx_divs[i].aosr * adc3xxx_divs[i].madc) / (2 * width);
1260 	snd_soc_component_update_bits(component, ADC3XXX_BCLK_N_DIV,
1261 				      ADC3XXX_BDIV_MASK, bdiv);
1262 
1263 	return 0;
1264 }
1265 
adc3xxx_pll_mode_text(int pll_mode)1266 static const char *adc3xxx_pll_mode_text(int pll_mode)
1267 {
1268 	switch (pll_mode) {
1269 	case ADC3XXX_PLL_AUTO:
1270 		return "PLL auto";
1271 	case ADC3XXX_PLL_ENABLE:
1272 		return "PLL enable";
1273 	case ADC3XXX_PLL_BYPASS:
1274 		return "PLL bypass";
1275 	default:
1276 		break;
1277 	}
1278 
1279 	return "PLL unknown";
1280 }
1281 
adc3xxx_set_dai_sysclk(struct snd_soc_dai * codec_dai,int clk_id,unsigned int freq,int dir)1282 static int adc3xxx_set_dai_sysclk(struct snd_soc_dai *codec_dai,
1283 				  int clk_id, unsigned int freq, int dir)
1284 {
1285 	struct snd_soc_component *component = codec_dai->component;
1286 	struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component);
1287 	int ret;
1288 
1289 	ret = adc3xxx_parse_pll_mode(clk_id, &adc3xxx->pll_mode);
1290 	if (ret < 0)
1291 		return ret;
1292 
1293 	adc3xxx->sysclk = freq;
1294 	dev_dbg(component->dev, "Set sysclk to %u Hz, %s\n",
1295 		freq, adc3xxx_pll_mode_text(adc3xxx->pll_mode));
1296 	return 0;
1297 }
1298 
adc3xxx_set_dai_fmt(struct snd_soc_dai * codec_dai,unsigned int fmt)1299 static int adc3xxx_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
1300 {
1301 	struct snd_soc_component *component = codec_dai->component;
1302 	struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component);
1303 	struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component);
1304 	u8 clkdir = 0, format = 0;
1305 	int master = 0;
1306 	int ret;
1307 
1308 	switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
1309 	case SND_SOC_DAIFMT_CBP_CFP:
1310 		master = 1;
1311 		clkdir = ADC3XXX_BCLK_MASTER | ADC3XXX_WCLK_MASTER;
1312 		break;
1313 	case SND_SOC_DAIFMT_CBC_CFC:
1314 		master = 0;
1315 		break;
1316 	default:
1317 		dev_err(component->dev, "Invalid DAI clock setup\n");
1318 		return -EINVAL;
1319 	}
1320 
1321 	/*
1322 	 * match both interface format and signal polarities since they
1323 	 * are fixed
1324 	 */
1325 	switch (fmt & (SND_SOC_DAIFMT_FORMAT_MASK | SND_SOC_DAIFMT_INV_MASK)) {
1326 	case SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF:
1327 		format = ADC3XXX_FORMAT_I2S;
1328 		break;
1329 	case SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_IB_NF:
1330 		format = ADC3XXX_FORMAT_DSP;
1331 		break;
1332 	case SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_IB_NF:
1333 		format = ADC3XXX_FORMAT_DSP;
1334 		break;
1335 	case SND_SOC_DAIFMT_RIGHT_J | SND_SOC_DAIFMT_NB_NF:
1336 		format = ADC3XXX_FORMAT_RJF;
1337 		break;
1338 	case SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_NB_NF:
1339 		format = ADC3XXX_FORMAT_LJF;
1340 		break;
1341 	default:
1342 		dev_err(component->dev, "Invalid DAI format\n");
1343 		return -EINVAL;
1344 	}
1345 
1346 	/* Add/del route enabling BCLK output as applicable */
1347 	if (master && !adc3xxx->master)
1348 		snd_soc_dapm_add_routes(dapm, adc3xxx_bclk_out_intercon,
1349 					ARRAY_SIZE(adc3xxx_bclk_out_intercon));
1350 	else if (!master && adc3xxx->master)
1351 		snd_soc_dapm_del_routes(dapm, adc3xxx_bclk_out_intercon,
1352 					ARRAY_SIZE(adc3xxx_bclk_out_intercon));
1353 	adc3xxx->master = master;
1354 
1355 	/* set clock direction and format */
1356 	ret = snd_soc_component_update_bits(component,
1357 					    ADC3XXX_INTERFACE_CTRL_1,
1358 					    ADC3XXX_CLKDIR_MASK | ADC3XXX_FORMAT_MASK,
1359 					    clkdir | format);
1360 	if (ret < 0)
1361 		return ret;
1362 	return 0;
1363 }
1364 
1365 static const struct snd_soc_dai_ops adc3xxx_dai_ops = {
1366 	.hw_params	= adc3xxx_hw_params,
1367 	.set_sysclk	= adc3xxx_set_dai_sysclk,
1368 	.set_fmt	= adc3xxx_set_dai_fmt,
1369 };
1370 
1371 static struct snd_soc_dai_driver adc3xxx_dai = {
1372 	.name = "tlv320adc3xxx-hifi",
1373 	.capture = {
1374 		    .stream_name = "Capture",
1375 		    .channels_min = 1,
1376 		    .channels_max = 2,
1377 		    .rates = ADC3XXX_RATES,
1378 		    .formats = ADC3XXX_FORMATS,
1379 		   },
1380 	.ops = &adc3xxx_dai_ops,
1381 };
1382 
1383 static const struct snd_soc_component_driver soc_component_dev_adc3xxx = {
1384 	.controls		= adc3xxx_snd_controls,
1385 	.num_controls		= ARRAY_SIZE(adc3xxx_snd_controls),
1386 	.dapm_widgets		= adc3xxx_dapm_widgets,
1387 	.num_dapm_widgets	= ARRAY_SIZE(adc3xxx_dapm_widgets),
1388 	.dapm_routes		= adc3xxx_intercon,
1389 	.num_dapm_routes	= ARRAY_SIZE(adc3xxx_intercon),
1390 	.endianness		= 1,
1391 };
1392 
1393 static const struct i2c_device_id adc3xxx_i2c_id[] = {
1394 	{ "tlv320adc3001", ADC3001 },
1395 	{ "tlv320adc3101", ADC3101 },
1396 	{}
1397 };
1398 MODULE_DEVICE_TABLE(i2c, adc3xxx_i2c_id);
1399 
adc3xxx_i2c_probe(struct i2c_client * i2c)1400 static int adc3xxx_i2c_probe(struct i2c_client *i2c)
1401 {
1402 	struct device *dev = &i2c->dev;
1403 	struct adc3xxx *adc3xxx = NULL;
1404 	const struct i2c_device_id *id;
1405 	int ret;
1406 
1407 	adc3xxx = devm_kzalloc(dev, sizeof(struct adc3xxx), GFP_KERNEL);
1408 	if (!adc3xxx)
1409 		return -ENOMEM;
1410 	adc3xxx->dev = dev;
1411 
1412 	adc3xxx->rst_pin = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
1413 	if (IS_ERR(adc3xxx->rst_pin)) {
1414 		return dev_err_probe(dev, PTR_ERR(adc3xxx->rst_pin),
1415 				     "Failed to request rst_pin\n");
1416 	}
1417 
1418 	adc3xxx->mclk = devm_clk_get(dev, NULL);
1419 	if (IS_ERR(adc3xxx->mclk)) {
1420 		/*
1421 		 * The chip itself supports running off the BCLK either
1422 		 * directly or via the PLL, but the driver does not (yet), so
1423 		 * having a specified mclk is required. Otherwise, we could
1424 		 * use the lack of a clocks property to indicate when BCLK is
1425 		 * intended as the clock source.
1426 		 */
1427 		return dev_err_probe(dev, PTR_ERR(adc3xxx->mclk),
1428 				     "Failed to acquire MCLK\n");
1429 	} else if (adc3xxx->mclk) {
1430 		ret = clk_prepare_enable(adc3xxx->mclk);
1431 		if (ret < 0)
1432 			return ret;
1433 		dev_dbg(dev, "Enabled MCLK, freq %lu Hz\n", clk_get_rate(adc3xxx->mclk));
1434 	}
1435 
1436 	/* Configure mode for DMDIN/GPIO1 pin */
1437 	ret = adc3xxx_parse_dt_gpio(adc3xxx, "ti,dmdin-gpio1", &adc3xxx->gpio_cfg[0]);
1438 	if (ret < 0)
1439 		goto err_unprepare_mclk;
1440 	/* Configure mode for DMCLK/GPIO2 pin */
1441 	ret = adc3xxx_parse_dt_gpio(adc3xxx, "ti,dmclk-gpio2", &adc3xxx->gpio_cfg[1]);
1442 	if (ret < 0)
1443 		goto err_unprepare_mclk;
1444 	/* Configure mode for MICBIAS1: as Mic Bias output or GPO */
1445 	ret = adc3xxx_parse_dt_micbias_gpo(adc3xxx, "ti,micbias1-gpo", &adc3xxx->micbias_gpo[0]);
1446 	if (ret < 0)
1447 		goto err_unprepare_mclk;
1448 	/* Configure mode for MICBIAS2: as Mic Bias output or GPO */
1449 	ret = adc3xxx_parse_dt_micbias_gpo(adc3xxx, "ti,micbias2-gpo", &adc3xxx->micbias_gpo[1]);
1450 	if (ret < 0)
1451 		goto err_unprepare_mclk;
1452 	/* Configure voltage for MICBIAS1 pin (ON voltage when used as GPO) */
1453 	ret = adc3xxx_parse_dt_micbias_vg(adc3xxx, "ti,micbias1-vg", &adc3xxx->micbias_vg[0]);
1454 	if (ret < 0)
1455 		goto err_unprepare_mclk;
1456 	/* Configure voltage for MICBIAS2 pin (ON voltage when used as GPO) */
1457 	ret = adc3xxx_parse_dt_micbias_vg(adc3xxx, "ti,micbias2-vg", &adc3xxx->micbias_vg[1]);
1458 	if (ret < 0)
1459 		goto err_unprepare_mclk;
1460 
1461 	adc3xxx->regmap = devm_regmap_init_i2c(i2c, &adc3xxx_regmap);
1462 	if (IS_ERR(adc3xxx->regmap)) {
1463 		ret = PTR_ERR(adc3xxx->regmap);
1464 		goto err_unprepare_mclk;
1465 	}
1466 
1467 	i2c_set_clientdata(i2c, adc3xxx);
1468 
1469 	id = i2c_match_id(adc3xxx_i2c_id, i2c);
1470 	adc3xxx->type = id->driver_data;
1471 
1472 	/* Reset codec chip */
1473 	gpiod_set_value_cansleep(adc3xxx->rst_pin, 1);
1474 	usleep_range(2000, 100000); /* Requirement: > 10 ns (datasheet p13) */
1475 	gpiod_set_value_cansleep(adc3xxx->rst_pin, 0);
1476 
1477 	/* Potentially set up pins used as GPIOs */
1478 	adc3xxx_init_gpio(adc3xxx);
1479 
1480 	ret = snd_soc_register_component(dev,
1481 			&soc_component_dev_adc3xxx, &adc3xxx_dai, 1);
1482 	if (ret < 0) {
1483 		dev_err(dev, "Failed to register codec: %d\n", ret);
1484 		goto err_unprepare_mclk;
1485 	}
1486 
1487 	return 0;
1488 
1489 err_unprepare_mclk:
1490 	clk_disable_unprepare(adc3xxx->mclk);
1491 	return ret;
1492 }
1493 
adc3xxx_i2c_remove(struct i2c_client * client)1494 static void adc3xxx_i2c_remove(struct i2c_client *client)
1495 {
1496 	struct adc3xxx *adc3xxx = i2c_get_clientdata(client);
1497 
1498 	if (adc3xxx->mclk)
1499 		clk_disable_unprepare(adc3xxx->mclk);
1500 	adc3xxx_free_gpio(adc3xxx);
1501 	snd_soc_unregister_component(&client->dev);
1502 }
1503 
1504 static const struct of_device_id tlv320adc3xxx_of_match[] = {
1505 	{ .compatible = "ti,tlv320adc3001", },
1506 	{ .compatible = "ti,tlv320adc3101", },
1507 	{},
1508 };
1509 MODULE_DEVICE_TABLE(of, tlv320adc3xxx_of_match);
1510 
1511 static struct i2c_driver adc3xxx_i2c_driver = {
1512 	.driver = {
1513 		   .name = "tlv320adc3xxx-codec",
1514 		   .of_match_table = tlv320adc3xxx_of_match,
1515 		  },
1516 	.probe = adc3xxx_i2c_probe,
1517 	.remove = adc3xxx_i2c_remove,
1518 	.id_table = adc3xxx_i2c_id,
1519 };
1520 
1521 module_i2c_driver(adc3xxx_i2c_driver);
1522 
1523 MODULE_DESCRIPTION("ASoC TLV320ADC3xxx codec driver");
1524 MODULE_AUTHOR("shahina.s@mistralsolutions.com");
1525 MODULE_LICENSE("GPL v2");
1526