1 // SPDX-License-Identifier: GPL-2.0+
2 /* Synopsys DesignWare 8250 library. */
3
4 #include <linux/bitops.h>
5 #include <linux/bitfield.h>
6 #include <linux/delay.h>
7 #include <linux/device.h>
8 #include <linux/kernel.h>
9 #include <linux/math.h>
10 #include <linux/property.h>
11 #include <linux/serial_8250.h>
12 #include <linux/serial_core.h>
13
14 #include "8250_dwlib.h"
15
16 /* Offsets for the DesignWare specific registers */
17 #define DW_UART_TCR 0xac /* Transceiver Control Register (RS485) */
18 #define DW_UART_DE_EN 0xb0 /* Driver Output Enable Register */
19 #define DW_UART_RE_EN 0xb4 /* Receiver Output Enable Register */
20 #define DW_UART_DLF 0xc0 /* Divisor Latch Fraction Register */
21 #define DW_UART_RAR 0xc4 /* Receive Address Register */
22 #define DW_UART_TAR 0xc8 /* Transmit Address Register */
23 #define DW_UART_LCR_EXT 0xcc /* Line Extended Control Register */
24 #define DW_UART_CPR 0xf4 /* Component Parameter Register */
25 #define DW_UART_UCV 0xf8 /* UART Component Version */
26
27 /* Receive / Transmit Address Register bits */
28 #define DW_UART_ADDR_MASK GENMASK(7, 0)
29
30 /* Line Status Register bits */
31 #define DW_UART_LSR_ADDR_RCVD BIT(8)
32
33 /* Transceiver Control Register bits */
34 #define DW_UART_TCR_RS485_EN BIT(0)
35 #define DW_UART_TCR_RE_POL BIT(1)
36 #define DW_UART_TCR_DE_POL BIT(2)
37 #define DW_UART_TCR_XFER_MODE GENMASK(4, 3)
38 #define DW_UART_TCR_XFER_MODE_DE_DURING_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 0)
39 #define DW_UART_TCR_XFER_MODE_SW_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 1)
40 #define DW_UART_TCR_XFER_MODE_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 2)
41
42 /* Line Extended Control Register bits */
43 #define DW_UART_LCR_EXT_DLS_E BIT(0)
44 #define DW_UART_LCR_EXT_ADDR_MATCH BIT(1)
45 #define DW_UART_LCR_EXT_SEND_ADDR BIT(2)
46 #define DW_UART_LCR_EXT_TRANSMIT_MODE BIT(3)
47
48 /* Component Parameter Register bits */
49 #define DW_UART_CPR_ABP_DATA_WIDTH GENMASK(1, 0)
50 #define DW_UART_CPR_AFCE_MODE BIT(4)
51 #define DW_UART_CPR_THRE_MODE BIT(5)
52 #define DW_UART_CPR_SIR_MODE BIT(6)
53 #define DW_UART_CPR_SIR_LP_MODE BIT(7)
54 #define DW_UART_CPR_ADDITIONAL_FEATURES BIT(8)
55 #define DW_UART_CPR_FIFO_ACCESS BIT(9)
56 #define DW_UART_CPR_FIFO_STAT BIT(10)
57 #define DW_UART_CPR_SHADOW BIT(11)
58 #define DW_UART_CPR_ENCODED_PARMS BIT(12)
59 #define DW_UART_CPR_DMA_EXTRA BIT(13)
60 #define DW_UART_CPR_FIFO_MODE GENMASK(23, 16)
61
62 /* Helper for FIFO size calculation */
63 #define DW_UART_CPR_FIFO_SIZE(a) (FIELD_GET(DW_UART_CPR_FIFO_MODE, (a)) * 16)
64
65 /*
66 * divisor = div(I) + div(F)
67 * "I" means integer, "F" means fractional
68 * quot = div(I) = clk / (16 * baud)
69 * frac = div(F) * 2^dlf_size
70 *
71 * let rem = clk % (16 * baud)
72 * we have: div(F) * (16 * baud) = rem
73 * so frac = 2^dlf_size * rem / (16 * baud) = (rem << dlf_size) / (16 * baud)
74 */
dw8250_get_divisor(struct uart_port * p,unsigned int baud,unsigned int * frac)75 static unsigned int dw8250_get_divisor(struct uart_port *p, unsigned int baud,
76 unsigned int *frac)
77 {
78 unsigned int quot, rem, base_baud = baud * 16;
79 struct dw8250_port_data *d = p->private_data;
80
81 quot = p->uartclk / base_baud;
82 rem = p->uartclk % base_baud;
83 *frac = DIV_ROUND_CLOSEST(rem << d->dlf_size, base_baud);
84
85 return quot;
86 }
87
dw8250_set_divisor(struct uart_port * p,unsigned int baud,unsigned int quot,unsigned int quot_frac)88 static void dw8250_set_divisor(struct uart_port *p, unsigned int baud,
89 unsigned int quot, unsigned int quot_frac)
90 {
91 dw8250_writel_ext(p, DW_UART_DLF, quot_frac);
92 serial8250_do_set_divisor(p, baud, quot);
93 }
94
dw8250_do_set_termios(struct uart_port * p,struct ktermios * termios,const struct ktermios * old)95 void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios,
96 const struct ktermios *old)
97 {
98 p->status &= ~UPSTAT_AUTOCTS;
99 if (termios->c_cflag & CRTSCTS)
100 p->status |= UPSTAT_AUTOCTS;
101
102 serial8250_do_set_termios(p, termios, old);
103
104 /* Filter addresses which have 9th bit set */
105 p->ignore_status_mask |= DW_UART_LSR_ADDR_RCVD;
106 p->read_status_mask |= DW_UART_LSR_ADDR_RCVD;
107 }
108 EXPORT_SYMBOL_GPL(dw8250_do_set_termios);
109
110 /*
111 * Wait until re is de-asserted for sure. An ongoing receive will keep
112 * re asserted until end of frame. Without BUSY indication available,
113 * only available course of action is to wait for the time it takes to
114 * receive one frame (there might nothing to receive but w/o BUSY the
115 * driver cannot know).
116 */
dw8250_wait_re_deassert(struct uart_port * p)117 static void dw8250_wait_re_deassert(struct uart_port *p)
118 {
119 ndelay(p->frame_time);
120 }
121
dw8250_update_rar(struct uart_port * p,u32 addr)122 static void dw8250_update_rar(struct uart_port *p, u32 addr)
123 {
124 u32 re_en = dw8250_readl_ext(p, DW_UART_RE_EN);
125
126 /*
127 * RAR shouldn't be changed while receiving. Thus, de-assert RE_EN
128 * if asserted and wait.
129 */
130 if (re_en)
131 dw8250_writel_ext(p, DW_UART_RE_EN, 0);
132 dw8250_wait_re_deassert(p);
133 dw8250_writel_ext(p, DW_UART_RAR, addr);
134 if (re_en)
135 dw8250_writel_ext(p, DW_UART_RE_EN, re_en);
136 }
137
dw8250_rs485_set_addr(struct uart_port * p,struct serial_rs485 * rs485,struct ktermios * termios)138 static void dw8250_rs485_set_addr(struct uart_port *p, struct serial_rs485 *rs485,
139 struct ktermios *termios)
140 {
141 u32 lcr = dw8250_readl_ext(p, DW_UART_LCR_EXT);
142
143 if (rs485->flags & SER_RS485_ADDRB) {
144 lcr |= DW_UART_LCR_EXT_DLS_E;
145 if (termios)
146 termios->c_cflag |= ADDRB;
147
148 if (rs485->flags & SER_RS485_ADDR_RECV) {
149 u32 delta = p->rs485.flags ^ rs485->flags;
150
151 /*
152 * rs485 (param) is equal to uart_port's rs485 only during init
153 * (during init, delta is not yet applicable).
154 */
155 if (unlikely(&p->rs485 == rs485))
156 delta = rs485->flags;
157
158 if ((delta & SER_RS485_ADDR_RECV) ||
159 (p->rs485.addr_recv != rs485->addr_recv))
160 dw8250_update_rar(p, rs485->addr_recv);
161 lcr |= DW_UART_LCR_EXT_ADDR_MATCH;
162 } else {
163 lcr &= ~DW_UART_LCR_EXT_ADDR_MATCH;
164 }
165 if (rs485->flags & SER_RS485_ADDR_DEST) {
166 /*
167 * Don't skip writes here as another endpoint could
168 * have changed communication line's destination
169 * address in between.
170 */
171 dw8250_writel_ext(p, DW_UART_TAR, rs485->addr_dest);
172 lcr |= DW_UART_LCR_EXT_SEND_ADDR;
173 }
174 } else {
175 lcr = 0;
176 }
177 dw8250_writel_ext(p, DW_UART_LCR_EXT, lcr);
178 }
179
dw8250_rs485_config(struct uart_port * p,struct ktermios * termios,struct serial_rs485 * rs485)180 static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
181 struct serial_rs485 *rs485)
182 {
183 u32 tcr;
184
185 tcr = dw8250_readl_ext(p, DW_UART_TCR);
186 tcr &= ~DW_UART_TCR_XFER_MODE;
187
188 if (rs485->flags & SER_RS485_ENABLED) {
189 tcr |= DW_UART_TCR_RS485_EN;
190
191 if (rs485->flags & SER_RS485_RX_DURING_TX)
192 tcr |= DW_UART_TCR_XFER_MODE_DE_DURING_RE;
193 else
194 tcr |= DW_UART_TCR_XFER_MODE_DE_OR_RE;
195 dw8250_writel_ext(p, DW_UART_DE_EN, 1);
196 dw8250_writel_ext(p, DW_UART_RE_EN, 1);
197 } else {
198 if (termios)
199 termios->c_cflag &= ~ADDRB;
200
201 tcr &= ~DW_UART_TCR_RS485_EN;
202 }
203
204 /* Reset to default polarity */
205 tcr |= DW_UART_TCR_DE_POL;
206 tcr &= ~DW_UART_TCR_RE_POL;
207
208 if (!(rs485->flags & SER_RS485_RTS_ON_SEND))
209 tcr &= ~DW_UART_TCR_DE_POL;
210 if (device_property_read_bool(p->dev, "rs485-rx-active-high"))
211 tcr |= DW_UART_TCR_RE_POL;
212
213 dw8250_writel_ext(p, DW_UART_TCR, tcr);
214
215 /* Addressing mode can only be set up after TCR */
216 if (rs485->flags & SER_RS485_ENABLED)
217 dw8250_rs485_set_addr(p, rs485, termios);
218
219 return 0;
220 }
221
222 /*
223 * Tests if RE_EN register can have non-zero value to see if RS-485 HW support
224 * is present.
225 */
dw8250_detect_rs485_hw(struct uart_port * p)226 static bool dw8250_detect_rs485_hw(struct uart_port *p)
227 {
228 u32 reg;
229
230 dw8250_writel_ext(p, DW_UART_RE_EN, 1);
231 reg = dw8250_readl_ext(p, DW_UART_RE_EN);
232 dw8250_writel_ext(p, DW_UART_RE_EN, 0);
233 return reg;
234 }
235
236 static const struct serial_rs485 dw8250_rs485_supported = {
237 .flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_RTS_ON_SEND |
238 SER_RS485_RTS_AFTER_SEND | SER_RS485_ADDRB | SER_RS485_ADDR_RECV |
239 SER_RS485_ADDR_DEST,
240 };
241
dw8250_setup_port(struct uart_port * p)242 void dw8250_setup_port(struct uart_port *p)
243 {
244 struct dw8250_port_data *pd = p->private_data;
245 struct uart_8250_port *up = up_to_u8250p(p);
246 u32 reg, old_dlf;
247
248 pd->hw_rs485_support = dw8250_detect_rs485_hw(p);
249 if (pd->hw_rs485_support) {
250 p->rs485_config = dw8250_rs485_config;
251 up->lsr_save_mask = LSR_SAVE_FLAGS | DW_UART_LSR_ADDR_RCVD;
252 p->rs485_supported = dw8250_rs485_supported;
253 } else {
254 p->rs485_config = serial8250_em485_config;
255 p->rs485_supported = serial8250_em485_supported;
256 up->rs485_start_tx = serial8250_em485_start_tx;
257 up->rs485_stop_tx = serial8250_em485_stop_tx;
258 }
259 up->capabilities |= UART_CAP_NOTEMT;
260
261 /* Preserve value written by firmware or bootloader */
262 old_dlf = dw8250_readl_ext(p, DW_UART_DLF);
263 dw8250_writel_ext(p, DW_UART_DLF, ~0U);
264 reg = dw8250_readl_ext(p, DW_UART_DLF);
265 dw8250_writel_ext(p, DW_UART_DLF, old_dlf);
266
267 if (reg) {
268 pd->dlf_size = fls(reg);
269 p->get_divisor = dw8250_get_divisor;
270 p->set_divisor = dw8250_set_divisor;
271 }
272
273 reg = dw8250_readl_ext(p, DW_UART_UCV);
274 if (reg)
275 dev_dbg(p->dev, "Designware UART version %c.%c%c\n",
276 (reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
277
278 reg = dw8250_readl_ext(p, DW_UART_CPR);
279 if (!reg) {
280 reg = pd->cpr_value;
281 dev_dbg(p->dev, "CPR is not available, using 0x%08x instead\n", reg);
282 }
283 if (!reg)
284 return;
285
286 /* Select the type based on FIFO */
287 if (reg & DW_UART_CPR_FIFO_MODE) {
288 p->type = PORT_16550A;
289 p->flags |= UPF_FIXED_TYPE;
290 p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
291 up->capabilities = UART_CAP_FIFO | UART_CAP_NOTEMT;
292 }
293
294 if (reg & DW_UART_CPR_AFCE_MODE)
295 up->capabilities |= UART_CAP_AFE;
296
297 if (reg & DW_UART_CPR_SIR_MODE)
298 up->capabilities |= UART_CAP_IRDA;
299 }
300 EXPORT_SYMBOL_GPL(dw8250_setup_port);
301