xref: /linux/drivers/spi/spi-stm32.c (revision 3974a585be78a1dc90a19d5cf1846a99954e3842)

// SPDX-License-Identifier: GPL-2.0
//
// STMicroelectronics STM32 SPI Controller driver
//
// Copyright (C) 2017, STMicroelectronics - All Rights Reserved
// Author(s): Amelie Delaunay <amelie.delaunay@st.com> for STMicroelectronics.

#include <linux/bitfield.h>
#include <linux/debugfs.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/genalloc.h>
#include <linux/interrupt.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/reset.h>
#include <linux/spi/spi.h>

#define DRIVER_NAME "spi_stm32"

/* STM32F4/7 SPI registers */
#define STM32FX_SPI_CR1			0x00
#define STM32FX_SPI_CR2			0x04
#define STM32FX_SPI_SR			0x08
#define STM32FX_SPI_DR			0x0C
#define STM32FX_SPI_I2SCFGR		0x1C

/* STM32FX_SPI_CR1 bit fields */
#define STM32FX_SPI_CR1_CPHA		BIT(0)
#define STM32FX_SPI_CR1_CPOL		BIT(1)
#define STM32FX_SPI_CR1_MSTR		BIT(2)
#define STM32FX_SPI_CR1_BR_SHIFT	3
#define STM32FX_SPI_CR1_BR		GENMASK(5, 3)
#define STM32FX_SPI_CR1_SPE		BIT(6)
#define STM32FX_SPI_CR1_LSBFRST		BIT(7)
#define STM32FX_SPI_CR1_SSI		BIT(8)
#define STM32FX_SPI_CR1_SSM		BIT(9)
#define STM32FX_SPI_CR1_RXONLY		BIT(10)
#define STM32F4_SPI_CR1_DFF		BIT(11)
#define STM32F7_SPI_CR1_CRCL		BIT(11)
#define STM32FX_SPI_CR1_CRCNEXT		BIT(12)
#define STM32FX_SPI_CR1_CRCEN		BIT(13)
#define STM32FX_SPI_CR1_BIDIOE		BIT(14)
#define STM32FX_SPI_CR1_BIDIMODE	BIT(15)
#define STM32FX_SPI_CR1_BR_MIN		0
#define STM32FX_SPI_CR1_BR_MAX		(GENMASK(5, 3) >> 3)

/* STM32FX_SPI_CR2 bit fields */
#define STM32FX_SPI_CR2_RXDMAEN		BIT(0)
#define STM32FX_SPI_CR2_TXDMAEN		BIT(1)
#define STM32FX_SPI_CR2_SSOE		BIT(2)
#define STM32FX_SPI_CR2_FRF		BIT(4)
#define STM32FX_SPI_CR2_ERRIE		BIT(5)
#define STM32FX_SPI_CR2_RXNEIE		BIT(6)
#define STM32FX_SPI_CR2_TXEIE		BIT(7)
#define STM32F7_SPI_CR2_DS		GENMASK(11, 8)
#define STM32F7_SPI_CR2_FRXTH		BIT(12)
#define STM32F7_SPI_CR2_LDMA_RX		BIT(13)
#define STM32F7_SPI_CR2_LDMA_TX		BIT(14)

/* STM32FX_SPI_SR bit fields */
#define STM32FX_SPI_SR_RXNE		BIT(0)
#define STM32FX_SPI_SR_TXE		BIT(1)
#define STM32FX_SPI_SR_CHSIDE		BIT(2)
#define STM32FX_SPI_SR_UDR		BIT(3)
#define STM32FX_SPI_SR_CRCERR		BIT(4)
#define STM32FX_SPI_SR_MODF		BIT(5)
#define STM32FX_SPI_SR_OVR		BIT(6)
#define STM32FX_SPI_SR_BSY		BIT(7)
#define STM32FX_SPI_SR_FRE		BIT(8)
#define STM32F7_SPI_SR_FRLVL		GENMASK(10, 9)
#define STM32F7_SPI_SR_FTLVL		GENMASK(12, 11)

/* STM32FX_SPI_I2SCFGR bit fields */
#define STM32FX_SPI_I2SCFGR_I2SMOD	BIT(11)

/* STM32F4 SPI Baud Rate min/max divisor */
#define STM32FX_SPI_BR_DIV_MIN		(2 << STM32FX_SPI_CR1_BR_MIN)
#define STM32FX_SPI_BR_DIV_MAX		(2 << STM32FX_SPI_CR1_BR_MAX)

/* STM32H7 SPI registers */
#define STM32H7_SPI_CR1			0x00
#define STM32H7_SPI_CR2			0x04
#define STM32H7_SPI_CFG1		0x08
#define STM32H7_SPI_CFG2		0x0C
#define STM32H7_SPI_IER			0x10
#define STM32H7_SPI_SR			0x14
#define STM32H7_SPI_IFCR		0x18
#define STM32H7_SPI_TXDR		0x20
#define STM32H7_SPI_RXDR		0x30
#define STM32H7_SPI_I2SCFGR		0x50

/* STM32H7_SPI_CR1 bit fields */
#define STM32H7_SPI_CR1_SPE		BIT(0)
#define STM32H7_SPI_CR1_MASRX		BIT(8)
#define STM32H7_SPI_CR1_CSTART		BIT(9)
#define STM32H7_SPI_CR1_CSUSP		BIT(10)
#define STM32H7_SPI_CR1_HDDIR		BIT(11)
#define STM32H7_SPI_CR1_SSI		BIT(12)

/* STM32H7_SPI_CR2 bit fields */
#define STM32H7_SPI_CR2_TSIZE		GENMASK(15, 0)
#define STM32H7_SPI_TSIZE_MAX		GENMASK(15, 0)

/* STM32H7_SPI_CFG1 bit fields */
#define STM32H7_SPI_CFG1_DSIZE		GENMASK(4, 0)
#define STM32H7_SPI_CFG1_FTHLV		GENMASK(8, 5)
#define STM32H7_SPI_CFG1_RXDMAEN	BIT(14)
#define STM32H7_SPI_CFG1_TXDMAEN	BIT(15)
#define STM32H7_SPI_CFG1_MBR		GENMASK(30, 28)
#define STM32H7_SPI_CFG1_MBR_SHIFT	28
#define STM32H7_SPI_CFG1_MBR_MIN	0
#define STM32H7_SPI_CFG1_MBR_MAX	(GENMASK(30, 28) >> 28)

/* STM32H7_SPI_CFG2 bit fields */
#define STM32H7_SPI_CFG2_MIDI		GENMASK(7, 4)
#define STM32H7_SPI_CFG2_COMM		GENMASK(18, 17)
#define STM32H7_SPI_CFG2_SP		GENMASK(21, 19)
#define STM32H7_SPI_CFG2_MASTER		BIT(22)
#define STM32H7_SPI_CFG2_LSBFRST	BIT(23)
#define STM32H7_SPI_CFG2_CPHA		BIT(24)
#define STM32H7_SPI_CFG2_CPOL		BIT(25)
#define STM32H7_SPI_CFG2_SSM		BIT(26)
#define STM32H7_SPI_CFG2_SSIOP		BIT(28)
#define STM32H7_SPI_CFG2_AFCNTR		BIT(31)

/* STM32H7_SPI_IER bit fields */
#define STM32H7_SPI_IER_RXPIE		BIT(0)
#define STM32H7_SPI_IER_TXPIE		BIT(1)
#define STM32H7_SPI_IER_DXPIE		BIT(2)
#define STM32H7_SPI_IER_EOTIE		BIT(3)
#define STM32H7_SPI_IER_TXTFIE		BIT(4)
#define STM32H7_SPI_IER_OVRIE		BIT(6)
#define STM32H7_SPI_IER_MODFIE		BIT(9)
#define STM32H7_SPI_IER_ALL		GENMASK(10, 0)

/* STM32H7_SPI_SR bit fields */
#define STM32H7_SPI_SR_RXP		BIT(0)
#define STM32H7_SPI_SR_TXP		BIT(1)
#define STM32H7_SPI_SR_EOT		BIT(3)
#define STM32H7_SPI_SR_OVR		BIT(6)
#define STM32H7_SPI_SR_MODF		BIT(9)
#define STM32H7_SPI_SR_SUSP		BIT(11)
#define STM32H7_SPI_SR_RXPLVL		GENMASK(14, 13)
#define STM32H7_SPI_SR_RXWNE		BIT(15)

/* STM32H7_SPI_IFCR bit fields */
#define STM32H7_SPI_IFCR_ALL		GENMASK(11, 3)

/* STM32H7_SPI_I2SCFGR bit fields */
#define STM32H7_SPI_I2SCFGR_I2SMOD	BIT(0)

/* STM32MP25_SPICFG2 bit fields */
#define STM32MP25_SPI_CFG2_RDIOM	BIT(13)

/* STM32MP25 SPI registers bit fields */
#define STM32MP25_SPI_HWCFGR1			0x3F0

/* STM32MP25_SPI_CR2 bit fields */
#define STM32MP25_SPI_TSIZE_MAX_LIMITED		GENMASK(9, 0)

/* STM32MP25_SPI_HWCFGR1 */
#define STM32MP25_SPI_HWCFGR1_FULLCFG		GENMASK(27, 24)
#define STM32MP25_SPI_HWCFGR1_FULLCFG_LIMITED	0x0
#define STM32MP25_SPI_HWCFGR1_FULLCFG_FULL	0x1
#define STM32MP25_SPI_HWCFGR1_DSCFG		GENMASK(19, 16)
#define STM32MP25_SPI_HWCFGR1_DSCFG_16_B	0x0
#define STM32MP25_SPI_HWCFGR1_DSCFG_32_B	0x1

/* STM32H7 SPI Master Baud Rate min/max divisor */
#define STM32H7_SPI_MBR_DIV_MIN		(2 << STM32H7_SPI_CFG1_MBR_MIN)
#define STM32H7_SPI_MBR_DIV_MAX		(2 << STM32H7_SPI_CFG1_MBR_MAX)

/* STM32H7 SPI Communication mode */
#define STM32H7_SPI_FULL_DUPLEX		0
#define STM32H7_SPI_SIMPLEX_TX		1
#define STM32H7_SPI_SIMPLEX_RX		2
#define STM32H7_SPI_HALF_DUPLEX		3

/* SPI Communication type */
#define SPI_FULL_DUPLEX		0
#define SPI_SIMPLEX_TX		1
#define SPI_SIMPLEX_RX		2
#define SPI_3WIRE_TX		3
#define SPI_3WIRE_RX		4

#define STM32_SPI_AUTOSUSPEND_DELAY		1	/* 1 ms */

/*
 * use PIO for small transfers, avoiding DMA setup/teardown overhead for drivers
 * without fifo buffers.
 */
#define SPI_DMA_MIN_BYTES	16

/* STM32 SPI driver helpers */
#define STM32_SPI_HOST_MODE(stm32_spi) (!(stm32_spi)->device_mode)
#define STM32_SPI_DEVICE_MODE(stm32_spi) ((stm32_spi)->device_mode)

static unsigned int polling_limit_us = 30;
module_param(polling_limit_us, uint, 0664);
MODULE_PARM_DESC(polling_limit_us, "maximum time in us to run a transfer in polling mode\n");

/**
 * struct stm32_spi_reg - stm32 SPI register & bitfield desc
 * @reg:		register offset
 * @mask:		bitfield mask
 * @shift:		left shift
 */
struct stm32_spi_reg {
	int reg;
	int mask;
	int shift;
};

/**
 * struct stm32_spi_regspec - stm32 registers definition, compatible dependent data
 * @en: enable register and SPI enable bit
 * @dma_rx_en: SPI DMA RX enable register end SPI DMA RX enable bit
 * @dma_tx_en: SPI DMA TX enable register end SPI DMA TX enable bit
 * @cpol: clock polarity register and polarity bit
 * @cpha: clock phase register and phase bit
 * @lsb_first: LSB transmitted first register and bit
 * @cs_high: chips select active value
 * @br: baud rate register and bitfields
 * @rx: SPI RX data register
 * @tx: SPI TX data register
 * @fullcfg: SPI full or limited feature set register
 * @rdy_en: SPI ready feature register
 */
struct stm32_spi_regspec {
	const struct stm32_spi_reg en;
	const struct stm32_spi_reg dma_rx_en;
	const struct stm32_spi_reg dma_tx_en;
	const struct stm32_spi_reg cpol;
	const struct stm32_spi_reg cpha;
	const struct stm32_spi_reg lsb_first;
	const struct stm32_spi_reg cs_high;
	const struct stm32_spi_reg br;
	const struct stm32_spi_reg rx;
	const struct stm32_spi_reg tx;
	const struct stm32_spi_reg fullcfg;
	const struct stm32_spi_reg rdy_en;
};

struct stm32_spi;

/**
 * struct stm32_spi_cfg - stm32 compatible configuration data
 * @regs: registers descriptions
 * @get_fifo_size: routine to get fifo size
 * @get_bpw_mask: routine to get bits per word mask
 * @disable: routine to disable controller
 * @config: routine to configure controller as SPI Host
 * @set_bpw: routine to configure registers to for bits per word
 * @set_mode: routine to configure registers to desired mode
 * @set_data_idleness: optional routine to configure registers to desired idle
 * time between frames (if driver has this functionality)
 * @set_number_of_data: optional routine to configure registers to desired
 * number of data (if driver has this functionality)
 * @write_tx: routine to write to transmit register/FIFO
 * @read_rx: routine to read from receive register/FIFO
 * @transfer_one_dma_start: routine to start transfer a single spi_transfer
 * using DMA
 * @dma_rx_cb: routine to call after DMA RX channel operation is complete
 * @dma_tx_cb: routine to call after DMA TX channel operation is complete
 * @transfer_one_irq: routine to configure interrupts for driver
 * @transfer_one_poll: routine to perform a transfer via register polling
 * @irq_handler_event: Interrupt handler for SPI controller events
 * @irq_handler_thread: thread of interrupt handler for SPI controller
 * @baud_rate_div_min: minimum baud rate divisor
 * @baud_rate_div_max: maximum baud rate divisor
 * @has_fifo: boolean to know if fifo is used for driver
 * @has_device_mode: is this compatible capable to switch on device mode
 * @flags: compatible specific SPI controller flags used at registration time
 * @prevent_dma_burst: boolean to indicate to prevent DMA burst
 */
struct stm32_spi_cfg {
	const struct stm32_spi_regspec *regs;
	int (*get_fifo_size)(struct stm32_spi *spi);
	int (*get_bpw_mask)(struct stm32_spi *spi);
	void (*disable)(struct stm32_spi *spi);
	int (*config)(struct stm32_spi *spi);
	void (*set_bpw)(struct stm32_spi *spi);
	int (*set_mode)(struct stm32_spi *spi, unsigned int comm_type);
	void (*set_data_idleness)(struct stm32_spi *spi, struct spi_transfer *xfer);
	int (*set_number_of_data)(struct stm32_spi *spi, u32 length);
	void (*write_tx)(struct stm32_spi *spi);
	void (*read_rx)(struct stm32_spi *spi);
	void (*transfer_one_dma_start)(struct stm32_spi *spi);
	void (*dma_rx_cb)(void *data);
	void (*dma_tx_cb)(void *data);
	int (*transfer_one_irq)(struct stm32_spi *spi);
	int (*transfer_one_poll)(struct stm32_spi *spi);
	irqreturn_t (*irq_handler_event)(int irq, void *dev_id);
	irqreturn_t (*irq_handler_thread)(int irq, void *dev_id);
	unsigned int baud_rate_div_min;
	unsigned int baud_rate_div_max;
	bool has_fifo;
	bool has_device_mode;
	u16 flags;
	bool prevent_dma_burst;
};

/**
 * struct stm32_spi - private data of the SPI controller
 * @dev: driver model representation of the controller
 * @ctrl: controller interface
 * @cfg: compatible configuration data
 * @base: virtual memory area
 * @clk: hw kernel clock feeding the SPI clock generator
 * @clk_rate: rate of the hw kernel clock feeding the SPI clock generator
 * @lock: prevent I/O concurrent access
 * @irq: SPI controller interrupt line
 * @fifo_size: size of the embedded fifo in bytes
 * @t_size_max: maximum number of data of one transfer
 * @feature_set: SPI full or limited feature set
 * @cur_midi: host inter-data idleness in ns
 * @cur_speed: speed configured in Hz
 * @cur_half_period: time of a half bit in us
 * @cur_bpw: number of bits in a single SPI data frame
 * @cur_fthlv: fifo threshold level (data frames in a single data packet)
 * @cur_comm: SPI communication mode
 * @cur_xferlen: current transfer length in bytes
 * @cur_usedma: boolean to know if dma is used in current transfer
 * @tx_buf: data to be written, or NULL
 * @rx_buf: data to be read, or NULL
 * @tx_len: number of data to be written in bytes
 * @rx_len: number of data to be read in bytes
 * @dma_tx: dma channel for TX transfer
 * @dma_rx: dma channel for RX transfer
 * @phys_addr: SPI registers physical base address
 * @device_mode: the controller is configured as SPI device
 * @sram_pool: SRAM pool for DMA transfers
 * @sram_rx_buf_size: size of SRAM buffer for RX transfer
 * @sram_rx_buf: SRAM buffer for RX transfer
 * @sram_dma_rx_buf: SRAM buffer physical address for RX transfer
 * @mdma_rx: MDMA channel for RX transfer
 */
struct stm32_spi {
	struct device *dev;
	struct spi_controller *ctrl;
	const struct stm32_spi_cfg *cfg;
	void __iomem *base;
	struct clk *clk;
	u32 clk_rate;
	spinlock_t lock; /* prevent I/O concurrent access */
	int irq;
	unsigned int fifo_size;
	unsigned int t_size_max;
	unsigned int feature_set;
#define STM32_SPI_FEATURE_LIMITED	STM32MP25_SPI_HWCFGR1_FULLCFG_LIMITED	/* 0x0 */
#define STM32_SPI_FEATURE_FULL		STM32MP25_SPI_HWCFGR1_FULLCFG_FULL	/* 0x1 */

	unsigned int cur_midi;
	unsigned int cur_speed;
	unsigned int cur_half_period;
	unsigned int cur_bpw;
	unsigned int cur_fthlv;
	unsigned int cur_comm;
	unsigned int cur_xferlen;
	bool cur_usedma;

	const void *tx_buf;
	void *rx_buf;
	int tx_len;
	int rx_len;
	struct dma_chan *dma_tx;
	struct dma_chan *dma_rx;
	dma_addr_t phys_addr;

	bool device_mode;

	struct gen_pool *sram_pool;
	size_t sram_rx_buf_size;
	void *sram_rx_buf;
	dma_addr_t sram_dma_rx_buf;
	struct dma_chan *mdma_rx;
};

static const struct stm32_spi_regspec stm32fx_spi_regspec = {
	.en = { STM32FX_SPI_CR1, STM32FX_SPI_CR1_SPE },

	.dma_rx_en = { STM32FX_SPI_CR2, STM32FX_SPI_CR2_RXDMAEN },
	.dma_tx_en = { STM32FX_SPI_CR2, STM32FX_SPI_CR2_TXDMAEN },

	.cpol = { STM32FX_SPI_CR1, STM32FX_SPI_CR1_CPOL },
	.cpha = { STM32FX_SPI_CR1, STM32FX_SPI_CR1_CPHA },
	.lsb_first = { STM32FX_SPI_CR1, STM32FX_SPI_CR1_LSBFRST },
	.cs_high = {},
	.br = { STM32FX_SPI_CR1, STM32FX_SPI_CR1_BR, STM32FX_SPI_CR1_BR_SHIFT },

	.rx = { STM32FX_SPI_DR },
	.tx = { STM32FX_SPI_DR },
};

static const struct stm32_spi_regspec stm32h7_spi_regspec = {
	/* SPI data transfer is enabled but spi_ker_ck is idle.
	 * CFG1 and CFG2 registers are write protected when SPE is enabled.
	 */
	.en = { STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE },

	.dma_rx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_RXDMAEN },
	.dma_tx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN },

	.cpol = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPOL },
	.cpha = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPHA },
	.lsb_first = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_LSBFRST },
	.cs_high = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_SSIOP },
	.br = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_MBR,
		STM32H7_SPI_CFG1_MBR_SHIFT },

	.rx = { STM32H7_SPI_RXDR },
	.tx = { STM32H7_SPI_TXDR },
};

static const struct stm32_spi_regspec stm32mp25_spi_regspec = {
	/* SPI data transfer is enabled but spi_ker_ck is idle.
	 * CFG1 and CFG2 registers are write protected when SPE is enabled.
	 */
	.en = { STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE },

	.dma_rx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_RXDMAEN },
	.dma_tx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN },

	.cpol = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPOL },
	.cpha = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPHA },
	.lsb_first = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_LSBFRST },
	.cs_high = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_SSIOP },
	.br = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_MBR,
		STM32H7_SPI_CFG1_MBR_SHIFT },

	.rx = { STM32H7_SPI_RXDR },
	.tx = { STM32H7_SPI_TXDR },

	.fullcfg = { STM32MP25_SPI_HWCFGR1, STM32MP25_SPI_HWCFGR1_FULLCFG },

	.rdy_en = { STM32H7_SPI_CFG2, STM32MP25_SPI_CFG2_RDIOM },
};

static inline void stm32_spi_set_bits(struct stm32_spi *spi,
				      u32 offset, u32 bits)
{
	writel_relaxed(readl_relaxed(spi->base + offset) | bits,
		       spi->base + offset);
}

static inline void stm32_spi_clr_bits(struct stm32_spi *spi,
				      u32 offset, u32 bits)
{
	writel_relaxed(readl_relaxed(spi->base + offset) & ~bits,
		       spi->base + offset);
}

/**
 * stm32h7_spi_get_fifo_size - Return fifo size
 * @spi: pointer to the spi controller data structure
 */
static int stm32h7_spi_get_fifo_size(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 count = 0;

	spin_lock_irqsave(&spi->lock, flags);

	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);

	while (readl_relaxed(spi->base + STM32H7_SPI_SR) & STM32H7_SPI_SR_TXP)
		writeb_relaxed(++count, spi->base + STM32H7_SPI_TXDR);

	stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);

	spin_unlock_irqrestore(&spi->lock, flags);

	dev_dbg(spi->dev, "%d x 8-bit fifo size\n", count);

	return count;
}

/**
 * stm32f4_spi_get_bpw_mask - Return bits per word mask
 * @spi: pointer to the spi controller data structure
 */
static int stm32f4_spi_get_bpw_mask(struct stm32_spi *spi)
{
	dev_dbg(spi->dev, "8-bit or 16-bit data frame supported\n");
	return SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
}

/**
 * stm32f7_spi_get_bpw_mask - Return bits per word mask
 * @spi: pointer to the spi controller data structure
 */
static int stm32f7_spi_get_bpw_mask(struct stm32_spi *spi)
{
	dev_dbg(spi->dev, "16-bit maximum data frame\n");
	return SPI_BPW_RANGE_MASK(4, 16);
}

/**
 * stm32h7_spi_get_bpw_mask - Return bits per word mask
 * @spi: pointer to the spi controller data structure
 */
static int stm32h7_spi_get_bpw_mask(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 cfg1, max_bpw;

	spin_lock_irqsave(&spi->lock, flags);

	/*
	 * The most significant bit at DSIZE bit field is reserved when the
	 * maximum data size of periperal instances is limited to 16-bit
	 */
	stm32_spi_set_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_DSIZE);

	cfg1 = readl_relaxed(spi->base + STM32H7_SPI_CFG1);
	max_bpw = FIELD_GET(STM32H7_SPI_CFG1_DSIZE, cfg1) + 1;

	spin_unlock_irqrestore(&spi->lock, flags);

	dev_dbg(spi->dev, "%d-bit maximum data frame\n", max_bpw);

	return SPI_BPW_RANGE_MASK(4, max_bpw);
}

/**
 * stm32mp25_spi_get_bpw_mask - Return bits per word mask
 * @spi: pointer to the spi controller data structure
 */
static int stm32mp25_spi_get_bpw_mask(struct stm32_spi *spi)
{
	u32 dscfg, max_bpw;

	if (spi->feature_set == STM32_SPI_FEATURE_LIMITED) {
		dev_dbg(spi->dev, "8-bit or 16-bit data frame supported\n");
		return SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
	}

	dscfg = FIELD_GET(STM32MP25_SPI_HWCFGR1_DSCFG,
			  readl_relaxed(spi->base + STM32MP25_SPI_HWCFGR1));
	max_bpw = 16;
	if (dscfg == STM32MP25_SPI_HWCFGR1_DSCFG_32_B)
		max_bpw = 32;
	dev_dbg(spi->dev, "%d-bit maximum data frame\n", max_bpw);
	return SPI_BPW_RANGE_MASK(4, max_bpw);
}

/**
 * stm32_spi_prepare_mbr - Determine baud rate divisor value
 * @spi: pointer to the spi controller data structure
 * @speed_hz: requested speed
 * @min_div: minimum baud rate divisor
 * @max_div: maximum baud rate divisor
 *
 * Return baud rate divisor value in case of success or -EINVAL
 */
static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz,
				 u32 min_div, u32 max_div)
{
	u32 div, mbrdiv;

	/* Ensure spi->clk_rate is even */
	div = DIV_ROUND_CLOSEST(spi->clk_rate & ~0x1, speed_hz);

	/*
	 * SPI framework set xfer->speed_hz to ctrl->max_speed_hz if
	 * xfer->speed_hz is greater than ctrl->max_speed_hz, and it returns
	 * an error when xfer->speed_hz is lower than ctrl->min_speed_hz, so
	 * no need to check it there.
	 * However, we need to ensure the following calculations.
	 */
	if ((div < min_div) || (div > max_div))
		return -EINVAL;

	/* Determine the first power of 2 greater than or equal to div */
	if (div & (div - 1))
		mbrdiv = fls(div);
	else
		mbrdiv = fls(div) - 1;

	spi->cur_speed = spi->clk_rate / (1 << mbrdiv);

	spi->cur_half_period = DIV_ROUND_CLOSEST(USEC_PER_SEC, 2 * spi->cur_speed);

	return mbrdiv - 1;
}

/**
 * stm32h7_spi_prepare_fthlv - Determine FIFO threshold level
 * @spi: pointer to the spi controller data structure
 * @xfer_len: length of the message to be transferred
 */
static u32 stm32h7_spi_prepare_fthlv(struct stm32_spi *spi, u32 xfer_len)
{
	u32 packet, bpw;

	/* data packet should not exceed 1/2 of fifo space */
	packet = clamp(xfer_len, 1U, spi->fifo_size / 2);

	/* align packet size with data registers access */
	bpw = DIV_ROUND_UP(spi->cur_bpw, 8);
	return DIV_ROUND_UP(packet, bpw);
}

/**
 * stm32f4_spi_write_tx - Write bytes to Transmit Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Read from tx_buf depends on remaining bytes to avoid to read beyond
 * tx_buf end.
 */
static void stm32f4_spi_write_tx(struct stm32_spi *spi)
{
	if ((spi->tx_len > 0) && (readl_relaxed(spi->base + STM32FX_SPI_SR) &
				  STM32FX_SPI_SR_TXE)) {
		u32 offs = spi->cur_xferlen - spi->tx_len;

		if (spi->cur_bpw == 16) {
			const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);

			writew_relaxed(*tx_buf16, spi->base + STM32FX_SPI_DR);
			spi->tx_len -= sizeof(u16);
		} else {
			const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);

			writeb_relaxed(*tx_buf8, spi->base + STM32FX_SPI_DR);
			spi->tx_len -= sizeof(u8);
		}
	}

	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
}

/**
 * stm32f7_spi_write_tx - Write bytes to Transmit Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Read from tx_buf depends on remaining bytes to avoid to read beyond
 * tx_buf end.
 */
static void stm32f7_spi_write_tx(struct stm32_spi *spi)
{
	if ((spi->tx_len > 0) && (readl_relaxed(spi->base + STM32FX_SPI_SR) &
				  STM32FX_SPI_SR_TXE)) {
		u32 offs = spi->cur_xferlen - spi->tx_len;

		if (spi->tx_len >= sizeof(u16)) {
			const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);

			writew_relaxed(*tx_buf16, spi->base + STM32FX_SPI_DR);
			spi->tx_len -= sizeof(u16);
		} else {
			const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);

			writeb_relaxed(*tx_buf8, spi->base + STM32FX_SPI_DR);
			spi->tx_len -= sizeof(u8);
		}
	}

	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
}

/**
 * stm32h7_spi_write_txfifo - Write bytes in Transmit Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Read from tx_buf depends on remaining bytes to avoid to read beyond
 * tx_buf end.
 */
static void stm32h7_spi_write_txfifo(struct stm32_spi *spi)
{
	while ((spi->tx_len > 0) &&
		       (readl_relaxed(spi->base + STM32H7_SPI_SR) &
			STM32H7_SPI_SR_TXP)) {
		u32 offs = spi->cur_xferlen - spi->tx_len;

		if (spi->tx_len >= sizeof(u32)) {
			const u32 *tx_buf32 = (const u32 *)(spi->tx_buf + offs);

			writel_relaxed(*tx_buf32, spi->base + STM32H7_SPI_TXDR);
			spi->tx_len -= sizeof(u32);
		} else if (spi->tx_len >= sizeof(u16)) {
			const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);

			writew_relaxed(*tx_buf16, spi->base + STM32H7_SPI_TXDR);
			spi->tx_len -= sizeof(u16);
		} else {
			const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);

			writeb_relaxed(*tx_buf8, spi->base + STM32H7_SPI_TXDR);
			spi->tx_len -= sizeof(u8);
		}
	}

	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
}

/**
 * stm32f4_spi_read_rx - Read bytes from Receive Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Write in rx_buf depends on remaining bytes to avoid to write beyond
 * rx_buf end.
 */
static void stm32f4_spi_read_rx(struct stm32_spi *spi)
{
	if ((spi->rx_len > 0) && (readl_relaxed(spi->base + STM32FX_SPI_SR) &
				  STM32FX_SPI_SR_RXNE)) {
		u32 offs = spi->cur_xferlen - spi->rx_len;

		if (spi->cur_bpw == 16) {
			u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);

			*rx_buf16 = readw_relaxed(spi->base + STM32FX_SPI_DR);
			spi->rx_len -= sizeof(u16);
		} else {
			u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);

			*rx_buf8 = readb_relaxed(spi->base + STM32FX_SPI_DR);
			spi->rx_len -= sizeof(u8);
		}
	}

	dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->rx_len);
}

/**
 * stm32f7_spi_read_rx - Read bytes from Receive Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Write in rx_buf depends on remaining bytes to avoid to write beyond
 * rx_buf end.
 */
static void stm32f7_spi_read_rx(struct stm32_spi *spi)
{
	u32 sr = readl_relaxed(spi->base + STM32FX_SPI_SR);
	u32 frlvl = FIELD_GET(STM32F7_SPI_SR_FRLVL, sr);

	while ((spi->rx_len > 0) && (frlvl > 0)) {
		u32 offs = spi->cur_xferlen - spi->rx_len;

		if ((spi->rx_len >= sizeof(u16)) && (frlvl >= 2)) {
			u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);

			*rx_buf16 = readw_relaxed(spi->base + STM32FX_SPI_DR);
			spi->rx_len -= sizeof(u16);
		} else {
			u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);

			*rx_buf8 = readb_relaxed(spi->base + STM32FX_SPI_DR);
			spi->rx_len -= sizeof(u8);
		}

		sr = readl_relaxed(spi->base + STM32FX_SPI_SR);
		frlvl = FIELD_GET(STM32F7_SPI_SR_FRLVL, sr);
	}

	if (spi->rx_len >= sizeof(u16))
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR2, STM32F7_SPI_CR2_FRXTH);
	else
		stm32_spi_set_bits(spi, STM32FX_SPI_CR2, STM32F7_SPI_CR2_FRXTH);

	dev_dbg(spi->dev, "%s: %d bytes left (sr=%08x)\n",
		__func__, spi->rx_len, sr);
}

/**
 * stm32h7_spi_read_rxfifo - Read bytes in Receive Data Register
 * @spi: pointer to the spi controller data structure
 *
 * Write in rx_buf depends on remaining bytes to avoid to write beyond
 * rx_buf end.
 */
static void stm32h7_spi_read_rxfifo(struct stm32_spi *spi)
{
	u32 sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
	u32 rxplvl = FIELD_GET(STM32H7_SPI_SR_RXPLVL, sr);

	while ((spi->rx_len > 0) &&
	       ((sr & STM32H7_SPI_SR_RXP) ||
		((sr & STM32H7_SPI_SR_EOT) &&
		 ((sr & STM32H7_SPI_SR_RXWNE) || (rxplvl > 0))))) {
		u32 offs = spi->cur_xferlen - spi->rx_len;

		if ((spi->rx_len >= sizeof(u32)) ||
		    (sr & STM32H7_SPI_SR_RXWNE)) {
			u32 *rx_buf32 = (u32 *)(spi->rx_buf + offs);

			*rx_buf32 = readl_relaxed(spi->base + STM32H7_SPI_RXDR);
			spi->rx_len -= sizeof(u32);
		} else if ((spi->rx_len >= sizeof(u16)) ||
			   (!(sr & STM32H7_SPI_SR_RXWNE) &&
			    (rxplvl >= 2 || spi->cur_bpw > 8))) {
			u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);

			*rx_buf16 = readw_relaxed(spi->base + STM32H7_SPI_RXDR);
			spi->rx_len -= sizeof(u16);
		} else {
			u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);

			*rx_buf8 = readb_relaxed(spi->base + STM32H7_SPI_RXDR);
			spi->rx_len -= sizeof(u8);
		}

		sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
		rxplvl = FIELD_GET(STM32H7_SPI_SR_RXPLVL, sr);
	}

	dev_dbg(spi->dev, "%s: %d bytes left (sr=%08x)\n",
		__func__, spi->rx_len, sr);
}

/**
 * stm32_spi_enable - Enable SPI controller
 * @spi: pointer to the spi controller data structure
 */
static void stm32_spi_enable(struct stm32_spi *spi)
{
	dev_dbg(spi->dev, "enable controller\n");

	stm32_spi_set_bits(spi, spi->cfg->regs->en.reg,
			   spi->cfg->regs->en.mask);
}

/**
 * stm32fx_spi_disable - Disable SPI controller
 * @spi: pointer to the spi controller data structure
 */
static void stm32fx_spi_disable(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 sr;

	dev_dbg(spi->dev, "disable controller\n");

	spin_lock_irqsave(&spi->lock, flags);

	if (!(readl_relaxed(spi->base + STM32FX_SPI_CR1) &
	      STM32FX_SPI_CR1_SPE)) {
		spin_unlock_irqrestore(&spi->lock, flags);
		return;
	}

	/* Disable interrupts */
	stm32_spi_clr_bits(spi, STM32FX_SPI_CR2, STM32FX_SPI_CR2_TXEIE |
						 STM32FX_SPI_CR2_RXNEIE |
						 STM32FX_SPI_CR2_ERRIE);

	/* Wait until BSY = 0 */
	if (readl_relaxed_poll_timeout_atomic(spi->base + STM32FX_SPI_SR,
					      sr, !(sr & STM32FX_SPI_SR_BSY),
					      10, 100000) < 0) {
		dev_warn(spi->dev, "disabling condition timeout\n");
	}

	if (spi->cur_usedma && spi->dma_tx)
		dmaengine_terminate_async(spi->dma_tx);
	if (spi->cur_usedma && spi->dma_rx)
		dmaengine_terminate_async(spi->dma_rx);

	stm32_spi_clr_bits(spi, STM32FX_SPI_CR1, STM32FX_SPI_CR1_SPE);

	stm32_spi_clr_bits(spi, STM32FX_SPI_CR2, STM32FX_SPI_CR2_TXDMAEN |
						 STM32FX_SPI_CR2_RXDMAEN);

	/* Sequence to clear OVR flag */
	readl_relaxed(spi->base + STM32FX_SPI_DR);
	readl_relaxed(spi->base + STM32FX_SPI_SR);

	spin_unlock_irqrestore(&spi->lock, flags);
}

/**
 * stm32h7_spi_disable - Disable SPI controller
 * @spi: pointer to the spi controller data structure
 *
 * RX-Fifo is flushed when SPI controller is disabled.
 */
static void stm32h7_spi_disable(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 cr1;

	dev_dbg(spi->dev, "disable controller\n");

	spin_lock_irqsave(&spi->lock, flags);

	cr1 = readl_relaxed(spi->base + STM32H7_SPI_CR1);

	if (!(cr1 & STM32H7_SPI_CR1_SPE)) {
		spin_unlock_irqrestore(&spi->lock, flags);
		return;
	}

	/* Add a delay to make sure that transmission is ended. */
	if (spi->cur_half_period)
		udelay(spi->cur_half_period);

	if (spi->cur_usedma && spi->dma_tx)
		dmaengine_terminate_async(spi->dma_tx);
	if (spi->cur_usedma && spi->dma_rx) {
		dmaengine_terminate_async(spi->dma_rx);
		if (spi->mdma_rx)
			dmaengine_terminate_async(spi->mdma_rx);
	}

	stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);

	stm32_spi_clr_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN |
						STM32H7_SPI_CFG1_RXDMAEN);

	/* Disable interrupts and clear status flags */
	writel_relaxed(0, spi->base + STM32H7_SPI_IER);
	writel_relaxed(STM32H7_SPI_IFCR_ALL, spi->base + STM32H7_SPI_IFCR);

	spin_unlock_irqrestore(&spi->lock, flags);
}

/**
 * stm32_spi_can_dma - Determine if the transfer is eligible for DMA use
 * @ctrl: controller interface
 * @spi_dev: pointer to the spi device
 * @transfer: pointer to spi transfer
 *
 * If driver has fifo and the current transfer size is greater than fifo size,
 * use DMA. Otherwise use DMA for transfer longer than defined DMA min bytes.
 */
static bool stm32_spi_can_dma(struct spi_controller *ctrl,
			      struct spi_device *spi_dev,
			      struct spi_transfer *transfer)
{
	unsigned int dma_size;
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	if (spi->cfg->has_fifo)
		dma_size = spi->fifo_size;
	else
		dma_size = SPI_DMA_MIN_BYTES;

	dev_dbg(spi->dev, "%s: %s\n", __func__,
		(transfer->len > dma_size) ? "true" : "false");

	return (transfer->len > dma_size);
}

/**
 * stm32fx_spi_irq_event - Interrupt handler for SPI controller events
 * @irq: interrupt line
 * @dev_id: SPI controller ctrl interface
 */
static irqreturn_t stm32fx_spi_irq_event(int irq, void *dev_id)
{
	struct spi_controller *ctrl = dev_id;
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	u32 sr, mask = 0;
	bool end = false;

	spin_lock(&spi->lock);

	sr = readl_relaxed(spi->base + STM32FX_SPI_SR);
	/*
	 * BSY flag is not handled in interrupt but it is normal behavior when
	 * this flag is set.
	 */
	sr &= ~STM32FX_SPI_SR_BSY;

	if (!spi->cur_usedma && (spi->cur_comm == SPI_SIMPLEX_TX ||
				 spi->cur_comm == SPI_3WIRE_TX)) {
		/* OVR flag shouldn't be handled for TX only mode */
		sr &= ~(STM32FX_SPI_SR_OVR | STM32FX_SPI_SR_RXNE);
		mask |= STM32FX_SPI_SR_TXE;
	}

	if (!spi->cur_usedma && (spi->cur_comm == SPI_FULL_DUPLEX ||
				spi->cur_comm == SPI_SIMPLEX_RX ||
				spi->cur_comm == SPI_3WIRE_RX)) {
		/* TXE flag is set and is handled when RXNE flag occurs */
		sr &= ~STM32FX_SPI_SR_TXE;
		mask |= STM32FX_SPI_SR_RXNE | STM32FX_SPI_SR_OVR;
	}

	if (!(sr & mask)) {
		dev_dbg(spi->dev, "spurious IT (sr=0x%08x)\n", sr);
		spin_unlock(&spi->lock);
		return IRQ_NONE;
	}

	if (sr & STM32FX_SPI_SR_OVR) {
		dev_warn(spi->dev, "Overrun: received value discarded\n");

		/* Sequence to clear OVR flag */
		readl_relaxed(spi->base + STM32FX_SPI_DR);
		readl_relaxed(spi->base + STM32FX_SPI_SR);

		/*
		 * If overrun is detected, it means that something went wrong,
		 * so stop the current transfer. Transfer can wait for next
		 * RXNE but DR is already read and end never happens.
		 */
		end = true;
		goto end_irq;
	}

	if (sr & STM32FX_SPI_SR_TXE) {
		if (spi->tx_buf)
			spi->cfg->write_tx(spi);
		if (spi->tx_len == 0)
			end = true;
	}

	if (sr & STM32FX_SPI_SR_RXNE) {
		spi->cfg->read_rx(spi);
		if (spi->rx_len == 0)
			end = true;
		else if (spi->tx_buf)/* Load data for discontinuous mode */
			spi->cfg->write_tx(spi);
	}

end_irq:
	if (end) {
		/* Immediately disable interrupts to do not generate new one */
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR2,
					STM32FX_SPI_CR2_TXEIE |
					STM32FX_SPI_CR2_RXNEIE |
					STM32FX_SPI_CR2_ERRIE);
		spin_unlock(&spi->lock);
		return IRQ_WAKE_THREAD;
	}

	spin_unlock(&spi->lock);
	return IRQ_HANDLED;
}

/**
 * stm32fx_spi_irq_thread - Thread of interrupt handler for SPI controller
 * @irq: interrupt line
 * @dev_id: SPI controller interface
 */
static irqreturn_t stm32fx_spi_irq_thread(int irq, void *dev_id)
{
	struct spi_controller *ctrl = dev_id;
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	spi_finalize_current_transfer(ctrl);
	stm32fx_spi_disable(spi);

	return IRQ_HANDLED;
}

/**
 * stm32h7_spi_irq_thread - Thread of interrupt handler for SPI controller
 * @irq: interrupt line
 * @dev_id: SPI controller interface
 */
static irqreturn_t stm32h7_spi_irq_thread(int irq, void *dev_id)
{
	struct spi_controller *ctrl = dev_id;
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	u32 sr, ier, mask;
	unsigned long flags;
	bool end = false;

	spin_lock_irqsave(&spi->lock, flags);

	sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
	ier = readl_relaxed(spi->base + STM32H7_SPI_IER);

	mask = ier;
	/*
	 * EOTIE enables irq from EOT, SUSP and TXC events. We need to set
	 * SUSP to acknowledge it later. TXC is automatically cleared
	 */

	mask |= STM32H7_SPI_SR_SUSP;
	/*
	 * DXPIE is set in Full-Duplex, one IT will be raised if TXP and RXP
	 * are set. So in case of Full-Duplex, need to poll TXP and RXP event.
	 */
	if ((spi->cur_comm == SPI_FULL_DUPLEX) && !spi->cur_usedma)
		mask |= STM32H7_SPI_SR_TXP | STM32H7_SPI_SR_RXP;

	if (!(sr & mask)) {
		dev_vdbg(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
			 sr, ier);
		spin_unlock_irqrestore(&spi->lock, flags);
		return IRQ_NONE;
	}

	if (sr & STM32H7_SPI_SR_SUSP) {
		static DEFINE_RATELIMIT_STATE(rs,
					      DEFAULT_RATELIMIT_INTERVAL * 10,
					      1);
		ratelimit_set_flags(&rs, RATELIMIT_MSG_ON_RELEASE);
		if (__ratelimit(&rs))
			dev_dbg_ratelimited(spi->dev, "Communication suspended\n");
		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
			stm32h7_spi_read_rxfifo(spi);
		/*
		 * If communication is suspended while using DMA, it means
		 * that something went wrong, so stop the current transfer
		 */
		if (spi->cur_usedma)
			end = true;
	}

	if (sr & STM32H7_SPI_SR_MODF) {
		dev_warn(spi->dev, "Mode fault: transfer aborted\n");
		end = true;
	}

	if (sr & STM32H7_SPI_SR_OVR) {
		dev_err(spi->dev, "Overrun: RX data lost\n");
		end = true;
	}

	if (sr & STM32H7_SPI_SR_EOT) {
		dev_dbg(spi->dev, "End of transfer\n");
		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
			stm32h7_spi_read_rxfifo(spi);
		if (!spi->cur_usedma ||
		    (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) ||
		    (spi->mdma_rx && (spi->cur_comm == SPI_SIMPLEX_RX ||
		     spi->cur_comm == SPI_FULL_DUPLEX)))
			end = true;
	}

	if (sr & STM32H7_SPI_SR_TXP)
		if (!spi->cur_usedma && (spi->tx_buf && (spi->tx_len > 0)))
			stm32h7_spi_write_txfifo(spi);

	if (sr & STM32H7_SPI_SR_RXP)
		if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
			stm32h7_spi_read_rxfifo(spi);

	writel_relaxed(sr & mask, spi->base + STM32H7_SPI_IFCR);

	spin_unlock_irqrestore(&spi->lock, flags);

	if (end) {
		if (spi->cur_usedma && spi->mdma_rx) {
			dmaengine_pause(spi->dma_rx);
			/* Wait for callback */
			return IRQ_HANDLED;
		}
		stm32h7_spi_disable(spi);
		spi_finalize_current_transfer(ctrl);
	}

	return IRQ_HANDLED;
}

static int stm32_spi_optimize_message(struct spi_message *msg)
{
	struct spi_controller *ctrl = msg->spi->controller;
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	/* On STM32H7, messages should not exceed a maximum size set
	 * later via the set_number_of_data function. In order to
	 * ensure that, split large messages into several messages
	 */
	if (spi->cfg->set_number_of_data)
		return spi_split_transfers_maxwords(ctrl, msg, spi->t_size_max);

	return 0;
}

/**
 * stm32_spi_prepare_msg - set up the controller to transfer a single message
 * @ctrl: controller interface
 * @msg: pointer to spi message
 */
static int stm32_spi_prepare_msg(struct spi_controller *ctrl,
				 struct spi_message *msg)
{
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	struct spi_device *spi_dev = msg->spi;
	struct device_node *np = spi_dev->dev.of_node;
	unsigned long flags;
	u32 clrb = 0, setb = 0;

	/* SPI target device may need time between data frames */
	spi->cur_midi = 0;
	if (np && !of_property_read_u32(np, "st,spi-midi-ns", &spi->cur_midi))
		dev_dbg(spi->dev, "%dns inter-data idleness\n", spi->cur_midi);

	if (spi_dev->mode & SPI_CPOL)
		setb |= spi->cfg->regs->cpol.mask;
	else
		clrb |= spi->cfg->regs->cpol.mask;

	if (spi_dev->mode & SPI_CPHA)
		setb |= spi->cfg->regs->cpha.mask;
	else
		clrb |= spi->cfg->regs->cpha.mask;

	if (spi_dev->mode & SPI_LSB_FIRST)
		setb |= spi->cfg->regs->lsb_first.mask;
	else
		clrb |= spi->cfg->regs->lsb_first.mask;

	if (STM32_SPI_DEVICE_MODE(spi) && spi_dev->mode & SPI_CS_HIGH)
		setb |= spi->cfg->regs->cs_high.mask;
	else
		clrb |= spi->cfg->regs->cs_high.mask;

	if (spi_dev->mode & SPI_READY)
		setb |= spi->cfg->regs->rdy_en.mask;
	else
		clrb |= spi->cfg->regs->rdy_en.mask;

	dev_dbg(spi->dev, "cpol=%d cpha=%d lsb_first=%d cs_high=%d rdy=%d\n",
		!!(spi_dev->mode & SPI_CPOL),
		!!(spi_dev->mode & SPI_CPHA),
		!!(spi_dev->mode & SPI_LSB_FIRST),
		!!(spi_dev->mode & SPI_CS_HIGH),
		!!(spi_dev->mode & SPI_READY));

	spin_lock_irqsave(&spi->lock, flags);

	/* CPOL, CPHA, LSB FIRST, CS_HIGH and RDY_EN bits have common register */
	if (clrb || setb)
		writel_relaxed(
			(readl_relaxed(spi->base + spi->cfg->regs->cpol.reg) &
			 ~clrb) | setb,
			spi->base + spi->cfg->regs->cpol.reg);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 0;
}

/**
 * stm32fx_spi_dma_tx_cb - dma callback
 * @data: pointer to the spi controller data structure
 *
 * DMA callback is called when the transfer is complete for DMA TX channel.
 */
static void stm32fx_spi_dma_tx_cb(void *data)
{
	struct stm32_spi *spi = data;

	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
		spi_finalize_current_transfer(spi->ctrl);
		stm32fx_spi_disable(spi);
	}
}

/**
 * stm32_spi_dma_rx_cb - dma callback
 * @data: pointer to the spi controller data structure
 *
 * DMA callback is called when the transfer is complete for DMA RX channel.
 */
static void stm32_spi_dma_rx_cb(void *data)
{
	struct stm32_spi *spi = data;

	spi_finalize_current_transfer(spi->ctrl);
	spi->cfg->disable(spi);
}

/**
 * stm32_spi_dma_config - configure dma slave channel depending on current
 *			  transfer bits_per_word.
 * @spi: pointer to the spi controller data structure
 * @dma_chan: pointer to the DMA channel
 * @dma_conf: pointer to the dma_slave_config structure
 * @dir: direction of the dma transfer
 */
static void stm32_spi_dma_config(struct stm32_spi *spi,
				 struct dma_chan *dma_chan,
				 struct dma_slave_config *dma_conf,
				 enum dma_transfer_direction dir)
{
	enum dma_slave_buswidth buswidth;
	struct dma_slave_caps caps;
	u32 maxburst = 1;
	int ret;

	if (spi->cur_bpw <= 8)
		buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
	else if (spi->cur_bpw <= 16)
		buswidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
	else
		buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES;

	/* Valid for DMA Half or Full Fifo threshold */
	if (!spi->cfg->prevent_dma_burst && spi->cfg->has_fifo && spi->cur_fthlv != 2)
		maxburst = spi->cur_fthlv;

	/* Get the DMA channel caps, and adjust maxburst if possible */
	ret = dma_get_slave_caps(dma_chan, &caps);
	if (!ret)
		maxburst = min(maxburst, caps.max_burst);

	memset(dma_conf, 0, sizeof(struct dma_slave_config));
	dma_conf->direction = dir;
	if (dma_conf->direction == DMA_DEV_TO_MEM) { /* RX */
		dma_conf->src_addr = spi->phys_addr + spi->cfg->regs->rx.reg;
		dma_conf->src_addr_width = buswidth;
		dma_conf->src_maxburst = maxburst;

		dev_dbg(spi->dev, "Rx DMA config buswidth=%d, maxburst=%d\n",
			buswidth, maxburst);
	} else if (dma_conf->direction == DMA_MEM_TO_DEV) { /* TX */
		dma_conf->dst_addr = spi->phys_addr + spi->cfg->regs->tx.reg;
		dma_conf->dst_addr_width = buswidth;
		dma_conf->dst_maxburst = maxburst;

		dev_dbg(spi->dev, "Tx DMA config buswidth=%d, maxburst=%d\n",
			buswidth, maxburst);
	}
}

/**
 * stm32fx_spi_transfer_one_irq - transfer a single spi_transfer using
 *				  interrupts
 * @spi: pointer to the spi controller data structure
 *
 * It must returns 0 if the transfer is finished or 1 if the transfer is still
 * in progress.
 */
static int stm32fx_spi_transfer_one_irq(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 cr2 = 0;

	/* Enable the interrupts relative to the current communication mode */
	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
		cr2 |= STM32FX_SPI_CR2_TXEIE;
	} else if (spi->cur_comm == SPI_FULL_DUPLEX ||
				spi->cur_comm == SPI_SIMPLEX_RX ||
				spi->cur_comm == SPI_3WIRE_RX) {
		/* In transmit-only mode, the OVR flag is set in the SR register
		 * since the received data are never read. Therefore set OVR
		 * interrupt only when rx buffer is available.
		 */
		cr2 |= STM32FX_SPI_CR2_RXNEIE | STM32FX_SPI_CR2_ERRIE;
	} else {
		return -EINVAL;
	}

	spin_lock_irqsave(&spi->lock, flags);

	stm32_spi_set_bits(spi, STM32FX_SPI_CR2, cr2);

	stm32_spi_enable(spi);

	/* starting data transfer when buffer is loaded */
	if (spi->tx_buf)
		spi->cfg->write_tx(spi);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 1;
}

/**
 * stm32h7_spi_transfer_one_poll - transfer a single spi_transfer by direct
 *				   register access without interrupt usage
 * @spi: pointer to the spi controller data structure
 *
 * It must returns 0 if the transfer is finished or 1 if the transfer is still
 * in progress.
 */
static int stm32h7_spi_transfer_one_poll(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 sr;

	spin_lock_irqsave(&spi->lock, flags);

	stm32_spi_enable(spi);

	/* Be sure to have data in fifo before starting data transfer */
	if (spi->tx_buf)
		stm32h7_spi_write_txfifo(spi);

	if (STM32_SPI_HOST_MODE(spi))
		stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);

	sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
	/* Keep writing / reading while waiting for the end of transfer */
	while (spi->tx_len || spi->rx_len || !(sr & STM32H7_SPI_SR_EOT)) {
		if (spi->rx_len && (sr & (STM32H7_SPI_SR_RXP | STM32H7_SPI_SR_RXWNE |
					  STM32H7_SPI_SR_RXPLVL)))
			stm32h7_spi_read_rxfifo(spi);

		if (spi->tx_len && (sr & STM32H7_SPI_SR_TXP))
			stm32h7_spi_write_txfifo(spi);

		sr = readl_relaxed(spi->base + STM32H7_SPI_SR);

		/* Clear suspension bit if necessary */
		if (sr & STM32H7_SPI_SR_SUSP)
			writel_relaxed(sr & STM32H7_SPI_SR_SUSP, spi->base + STM32H7_SPI_IFCR);
	}

	spin_unlock_irqrestore(&spi->lock, flags);

	stm32h7_spi_disable(spi);
	spi_finalize_current_transfer(spi->ctrl);

	return 0;
}

/**
 * stm32h7_spi_transfer_one_irq - transfer a single spi_transfer using
 *				  interrupts
 * @spi: pointer to the spi controller data structure
 *
 * It must returns 0 if the transfer is finished or 1 if the transfer is still
 * in progress.
 */
static int stm32h7_spi_transfer_one_irq(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 ier = 0;

	/* Enable the interrupts relative to the current communication mode */
	if (spi->tx_buf && spi->rx_buf)	/* Full Duplex */
		ier |= STM32H7_SPI_IER_DXPIE;
	else if (spi->tx_buf)		/* Half-Duplex TX dir or Simplex TX */
		ier |= STM32H7_SPI_IER_TXPIE;
	else if (spi->rx_buf)		/* Half-Duplex RX dir or Simplex RX */
		ier |= STM32H7_SPI_IER_RXPIE;

	/* Enable the interrupts relative to the end of transfer */
	ier |= STM32H7_SPI_IER_EOTIE | STM32H7_SPI_IER_TXTFIE |
	       STM32H7_SPI_IER_OVRIE | STM32H7_SPI_IER_MODFIE;

	spin_lock_irqsave(&spi->lock, flags);

	stm32_spi_enable(spi);

	/* Be sure to have data in fifo before starting data transfer */
	if (spi->tx_buf)
		stm32h7_spi_write_txfifo(spi);

	if (STM32_SPI_HOST_MODE(spi))
		stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);

	writel_relaxed(ier, spi->base + STM32H7_SPI_IER);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 1;
}

/**
 * stm32fx_spi_transfer_one_dma_start - Set SPI driver registers to start
 *					transfer using DMA
 * @spi: pointer to the spi controller data structure
 */
static void stm32fx_spi_transfer_one_dma_start(struct stm32_spi *spi)
{
	/* In DMA mode end of transfer is handled by DMA TX or RX callback. */
	if (spi->cur_comm == SPI_SIMPLEX_RX || spi->cur_comm == SPI_3WIRE_RX ||
	    spi->cur_comm == SPI_FULL_DUPLEX) {
		/*
		 * In transmit-only mode, the OVR flag is set in the SR register
		 * since the received data are never read. Therefore set OVR
		 * interrupt only when rx buffer is available.
		 */
		stm32_spi_set_bits(spi, STM32FX_SPI_CR2, STM32FX_SPI_CR2_ERRIE);
	}

	stm32_spi_enable(spi);
}

/**
 * stm32f7_spi_transfer_one_dma_start - Set SPI driver registers to start
 *					transfer using DMA
 * @spi: pointer to the spi controller data structure
 */
static void stm32f7_spi_transfer_one_dma_start(struct stm32_spi *spi)
{
	/* Configure DMA request trigger threshold according to DMA width */
	if (spi->cur_bpw <= 8)
		stm32_spi_set_bits(spi, STM32FX_SPI_CR2, STM32F7_SPI_CR2_FRXTH);
	else
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR2, STM32F7_SPI_CR2_FRXTH);

	stm32fx_spi_transfer_one_dma_start(spi);
}

/**
 * stm32h7_spi_transfer_one_dma_start - Set SPI driver registers to start
 *					transfer using DMA
 * @spi: pointer to the spi controller data structure
 */
static void stm32h7_spi_transfer_one_dma_start(struct stm32_spi *spi)
{
	uint32_t ier = STM32H7_SPI_IER_OVRIE | STM32H7_SPI_IER_MODFIE;

	/* Enable the interrupts */
	if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX)
		ier |= STM32H7_SPI_IER_EOTIE | STM32H7_SPI_IER_TXTFIE;
	if (spi->mdma_rx && (spi->cur_comm == SPI_SIMPLEX_RX || spi->cur_comm == SPI_FULL_DUPLEX))
		ier |= STM32H7_SPI_IER_EOTIE;

	stm32_spi_set_bits(spi, STM32H7_SPI_IER, ier);

	stm32_spi_enable(spi);

	if (STM32_SPI_HOST_MODE(spi))
		stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);
}

/**
 * stm32_spi_prepare_rx_dma_mdma_chaining - Prepare RX DMA and MDMA chaining
 * @spi: pointer to the spi controller data structure
 * @xfer: pointer to the spi transfer
 * @rx_dma_conf: pointer to the DMA configuration for RX channel
 * @rx_dma_desc: pointer to the RX DMA descriptor
 * @rx_mdma_desc: pointer to the RX MDMA descriptor
 *
 * It must return 0 if the chaining is possible or an error code if not.
 */
static int stm32_spi_prepare_rx_dma_mdma_chaining(struct stm32_spi *spi,
						  struct spi_transfer *xfer,
						  struct dma_slave_config *rx_dma_conf,
						  struct dma_async_tx_descriptor **rx_dma_desc,
						  struct dma_async_tx_descriptor **rx_mdma_desc)
{
	struct dma_async_tx_descriptor *_mdma_desc = *rx_mdma_desc;
	struct dma_async_tx_descriptor *_dma_desc = *rx_dma_desc;
	struct dma_slave_config rx_mdma_conf = {0};
	u32 sram_period, nents = 0, spi_s_len;
	struct sg_table dma_sgt, mdma_sgt;
	struct scatterlist *spi_s, *s;
	dma_addr_t dma_buf;
	int i, ret;

	sram_period = spi->sram_rx_buf_size / 2;

	/* Configure MDMA RX channel */
	rx_mdma_conf.direction = rx_dma_conf->direction;
	rx_mdma_conf.src_addr = spi->sram_dma_rx_buf;
	rx_mdma_conf.peripheral_config = rx_dma_conf->peripheral_config;
	rx_mdma_conf.peripheral_size = rx_dma_conf->peripheral_size;
	dmaengine_slave_config(spi->mdma_rx, &rx_mdma_conf);

	/* Count the number of entries needed */
	for_each_sg(xfer->rx_sg.sgl, spi_s, xfer->rx_sg.nents, i)
		if (sg_dma_len(spi_s) > sram_period)
			nents += DIV_ROUND_UP(sg_dma_len(spi_s), sram_period);
		else
			nents++;

	/* Prepare DMA slave_sg DBM transfer DEV_TO_MEM (RX>MEM=SRAM) */
	ret = sg_alloc_table(&dma_sgt, nents, GFP_ATOMIC);
	if (ret)
		return ret;

	spi_s = xfer->rx_sg.sgl;
	spi_s_len = sg_dma_len(spi_s);
	dma_buf = spi->sram_dma_rx_buf;
	for_each_sg(dma_sgt.sgl, s, dma_sgt.nents, i) {
		size_t bytes = min_t(size_t, spi_s_len, sram_period);

		sg_dma_len(s) = bytes;
		sg_dma_address(s) = dma_buf;
		spi_s_len -= bytes;

		if (!spi_s_len && sg_next(spi_s)) {
			spi_s = sg_next(spi_s);
			spi_s_len = sg_dma_len(spi_s);
			dma_buf = spi->sram_dma_rx_buf;
		} else { /* DMA configured in DBM: it will swap between the SRAM periods */
			if (i & 1)
				dma_buf += sram_period;
			else
				dma_buf = spi->sram_dma_rx_buf;
		}
	}

	_dma_desc = dmaengine_prep_slave_sg(spi->dma_rx, dma_sgt.sgl,
					    dma_sgt.nents, rx_dma_conf->direction,
					    DMA_PREP_INTERRUPT);
	sg_free_table(&dma_sgt);

	if (!_dma_desc)
		return -EINVAL;

	/* Prepare MDMA slave_sg transfer MEM_TO_MEM (SRAM>DDR) */
	ret = sg_alloc_table(&mdma_sgt, nents, GFP_ATOMIC);
	if (ret) {
		_dma_desc = NULL;
		return ret;
	}

	spi_s = xfer->rx_sg.sgl;
	spi_s_len = sg_dma_len(spi_s);
	dma_buf = sg_dma_address(spi_s);
	for_each_sg(mdma_sgt.sgl, s, mdma_sgt.nents, i) {
		size_t bytes = min_t(size_t, spi_s_len, sram_period);

		sg_dma_len(s) = bytes;
		sg_dma_address(s) = dma_buf;
		spi_s_len -= bytes;

		if (!spi_s_len && sg_next(spi_s)) {
			spi_s = sg_next(spi_s);
			spi_s_len = sg_dma_len(spi_s);
			dma_buf = sg_dma_address(spi_s);
		} else {
			dma_buf += bytes;
		}
	}

	_mdma_desc = dmaengine_prep_slave_sg(spi->mdma_rx, mdma_sgt.sgl,
					     mdma_sgt.nents, rx_mdma_conf.direction,
					     DMA_PREP_INTERRUPT);
	sg_free_table(&mdma_sgt);

	if (!_mdma_desc) {
		_dma_desc = NULL;
		return -EINVAL;
	}

	return 0;
}

/**
 * stm32_spi_transfer_one_dma - transfer a single spi_transfer using DMA
 * @spi: pointer to the spi controller data structure
 * @xfer: pointer to the spi_transfer structure
 *
 * It must returns 0 if the transfer is finished or 1 if the transfer is still
 * in progress.
 */
static int stm32_spi_transfer_one_dma(struct stm32_spi *spi,
				      struct spi_transfer *xfer)
{
	struct dma_async_tx_descriptor *rx_mdma_desc = NULL, *rx_dma_desc = NULL;
	struct dma_async_tx_descriptor *tx_dma_desc = NULL;
	struct dma_slave_config tx_dma_conf, rx_dma_conf;
	unsigned long flags;
	int ret = 0;

	spin_lock_irqsave(&spi->lock, flags);

	if (spi->rx_buf && spi->dma_rx) {
		stm32_spi_dma_config(spi, spi->dma_rx, &rx_dma_conf, DMA_DEV_TO_MEM);
		if (spi->mdma_rx) {
			rx_dma_conf.peripheral_size = 1;
			dmaengine_slave_config(spi->dma_rx, &rx_dma_conf);

			ret = stm32_spi_prepare_rx_dma_mdma_chaining(spi, xfer, &rx_dma_conf,
								     &rx_dma_desc, &rx_mdma_desc);
			if (ret) { /* RX DMA MDMA chaining not possible, fallback to DMA only */
				rx_dma_conf.peripheral_config = 0;
				rx_dma_desc = NULL;
			}
		}
		if (!rx_dma_desc) {
			dmaengine_slave_config(spi->dma_rx, &rx_dma_conf);
			rx_dma_desc = dmaengine_prep_slave_sg(spi->dma_rx, xfer->rx_sg.sgl,
							      xfer->rx_sg.nents,
							      rx_dma_conf.direction,
							      DMA_PREP_INTERRUPT);
		}
	}

	if (spi->tx_buf && spi->dma_tx) {
		stm32_spi_dma_config(spi, spi->dma_tx, &tx_dma_conf, DMA_MEM_TO_DEV);
		dmaengine_slave_config(spi->dma_tx, &tx_dma_conf);
		tx_dma_desc = dmaengine_prep_slave_sg(spi->dma_tx, xfer->tx_sg.sgl,
						      xfer->tx_sg.nents,
						      tx_dma_conf.direction,
						      DMA_PREP_INTERRUPT);
	}

	if ((spi->tx_buf && spi->dma_tx && !tx_dma_desc) ||
	    (spi->rx_buf && spi->dma_rx && !rx_dma_desc))
		goto dma_desc_error;

	if (spi->cur_comm == SPI_FULL_DUPLEX && (!tx_dma_desc || !rx_dma_desc))
		goto dma_desc_error;

	if (rx_dma_desc) {
		if (rx_mdma_desc) {
			rx_mdma_desc->callback = spi->cfg->dma_rx_cb;
			rx_mdma_desc->callback_param = spi;
		} else {
			rx_dma_desc->callback = spi->cfg->dma_rx_cb;
			rx_dma_desc->callback_param = spi;
		}

		/* Enable Rx DMA request */
		stm32_spi_set_bits(spi, spi->cfg->regs->dma_rx_en.reg,
				   spi->cfg->regs->dma_rx_en.mask);
		if (rx_mdma_desc) {
			if (dma_submit_error(dmaengine_submit(rx_mdma_desc))) {
				dev_err(spi->dev, "Rx MDMA submit failed\n");
				goto dma_desc_error;
			}
			/* Enable Rx MDMA channel */
			dma_async_issue_pending(spi->mdma_rx);
		}
		if (dma_submit_error(dmaengine_submit(rx_dma_desc))) {
			dev_err(spi->dev, "Rx DMA submit failed\n");
			goto dma_desc_error;
		}
		/* Enable Rx DMA channel */
		dma_async_issue_pending(spi->dma_rx);
	}

	if (tx_dma_desc) {
		if (spi->cur_comm == SPI_SIMPLEX_TX ||
		    spi->cur_comm == SPI_3WIRE_TX) {
			tx_dma_desc->callback = spi->cfg->dma_tx_cb;
			tx_dma_desc->callback_param = spi;
		}

		if (dma_submit_error(dmaengine_submit(tx_dma_desc))) {
			dev_err(spi->dev, "Tx DMA submit failed\n");
			goto dma_submit_error;
		}
		/* Enable Tx DMA channel */
		dma_async_issue_pending(spi->dma_tx);

		/* Enable Tx DMA request */
		stm32_spi_set_bits(spi, spi->cfg->regs->dma_tx_en.reg,
				   spi->cfg->regs->dma_tx_en.mask);
	}

	spi->cfg->transfer_one_dma_start(spi);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 1;

dma_submit_error:
	if (spi->mdma_rx)
		dmaengine_terminate_sync(spi->mdma_rx);
	if (spi->dma_rx)
		dmaengine_terminate_sync(spi->dma_rx);

dma_desc_error:
	stm32_spi_clr_bits(spi, spi->cfg->regs->dma_rx_en.reg,
			   spi->cfg->regs->dma_rx_en.mask);

	spin_unlock_irqrestore(&spi->lock, flags);

	dev_info(spi->dev, "DMA issue: fall back to irq transfer\n");

	if (spi->sram_rx_buf)
		memset(spi->sram_rx_buf, 0, spi->sram_rx_buf_size);

	spi->cur_usedma = false;
	return spi->cfg->transfer_one_irq(spi);
}

/**
 * stm32f4_spi_set_bpw - Configure bits per word
 * @spi: pointer to the spi controller data structure
 */
static void stm32f4_spi_set_bpw(struct stm32_spi *spi)
{
	if (spi->cur_bpw == 16)
		stm32_spi_set_bits(spi, STM32FX_SPI_CR1, STM32F4_SPI_CR1_DFF);
	else
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR1, STM32F4_SPI_CR1_DFF);
}

/**
 * stm32f7_spi_set_bpw - Configure bits per word
 * @spi: pointer to the spi controller data structure
 */
static void stm32f7_spi_set_bpw(struct stm32_spi *spi)
{
	u32 bpw;
	u32 cr2_clrb = 0, cr2_setb = 0;

	bpw = spi->cur_bpw - 1;

	cr2_clrb |= STM32F7_SPI_CR2_DS;
	cr2_setb |= FIELD_PREP(STM32F7_SPI_CR2_DS, bpw);

	if (spi->rx_len >= sizeof(u16))
		cr2_clrb |= STM32F7_SPI_CR2_FRXTH;
	else
		cr2_setb |= STM32F7_SPI_CR2_FRXTH;

	writel_relaxed(
		(readl_relaxed(spi->base + STM32FX_SPI_CR2) &
		 ~cr2_clrb) | cr2_setb,
		spi->base + STM32FX_SPI_CR2);
}

/**
 * stm32h7_spi_set_bpw - configure bits per word
 * @spi: pointer to the spi controller data structure
 */
static void stm32h7_spi_set_bpw(struct stm32_spi *spi)
{
	u32 bpw, fthlv;
	u32 cfg1_clrb = 0, cfg1_setb = 0;

	bpw = spi->cur_bpw - 1;

	cfg1_clrb |= STM32H7_SPI_CFG1_DSIZE;
	cfg1_setb |= FIELD_PREP(STM32H7_SPI_CFG1_DSIZE, bpw);

	spi->cur_fthlv = stm32h7_spi_prepare_fthlv(spi, spi->cur_xferlen);
	fthlv = spi->cur_fthlv - 1;

	cfg1_clrb |= STM32H7_SPI_CFG1_FTHLV;
	cfg1_setb |= FIELD_PREP(STM32H7_SPI_CFG1_FTHLV, fthlv);

	writel_relaxed(
		(readl_relaxed(spi->base + STM32H7_SPI_CFG1) &
		 ~cfg1_clrb) | cfg1_setb,
		spi->base + STM32H7_SPI_CFG1);
}

/**
 * stm32_spi_set_mbr - Configure baud rate divisor in host mode
 * @spi: pointer to the spi controller data structure
 * @mbrdiv: baud rate divisor value
 */
static void stm32_spi_set_mbr(struct stm32_spi *spi, u32 mbrdiv)
{
	u32 clrb = 0, setb = 0;

	clrb |= spi->cfg->regs->br.mask;
	setb |= (mbrdiv << spi->cfg->regs->br.shift) & spi->cfg->regs->br.mask;

	writel_relaxed((readl_relaxed(spi->base + spi->cfg->regs->br.reg) &
			~clrb) | setb,
		       spi->base + spi->cfg->regs->br.reg);
}

/**
 * stm32_spi_communication_type - return transfer communication type
 * @spi_dev: pointer to the spi device
 * @transfer: pointer to spi transfer
 */
static unsigned int stm32_spi_communication_type(struct spi_device *spi_dev,
						 struct spi_transfer *transfer)
{
	unsigned int type = SPI_FULL_DUPLEX;

	if (spi_dev->mode & SPI_3WIRE) { /* MISO/MOSI signals shared */
		/*
		 * SPI_3WIRE and xfer->tx_buf != NULL and xfer->rx_buf != NULL
		 * is forbidden and unvalidated by SPI subsystem so depending
		 * on the valid buffer, we can determine the direction of the
		 * transfer.
		 */
		if (!transfer->tx_buf)
			type = SPI_3WIRE_RX;
		else
			type = SPI_3WIRE_TX;
	} else {
		if (!transfer->tx_buf)
			type = SPI_SIMPLEX_RX;
		else if (!transfer->rx_buf)
			type = SPI_SIMPLEX_TX;
	}

	return type;
}

/**
 * stm32fx_spi_set_mode - configure communication mode
 * @spi: pointer to the spi controller data structure
 * @comm_type: type of communication to configure
 */
static int stm32fx_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
{
	if (comm_type == SPI_3WIRE_TX || comm_type == SPI_SIMPLEX_TX) {
		stm32_spi_set_bits(spi, STM32FX_SPI_CR1,
					STM32FX_SPI_CR1_BIDIMODE |
					STM32FX_SPI_CR1_BIDIOE);
	} else if (comm_type == SPI_FULL_DUPLEX ||
				comm_type == SPI_SIMPLEX_RX) {
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR1,
					STM32FX_SPI_CR1_BIDIMODE |
					STM32FX_SPI_CR1_BIDIOE);
	} else if (comm_type == SPI_3WIRE_RX) {
		stm32_spi_set_bits(spi, STM32FX_SPI_CR1,
					STM32FX_SPI_CR1_BIDIMODE);
		stm32_spi_clr_bits(spi, STM32FX_SPI_CR1,
					STM32FX_SPI_CR1_BIDIOE);
	} else {
		return -EINVAL;
	}

	return 0;
}

/**
 * stm32h7_spi_set_mode - configure communication mode
 * @spi: pointer to the spi controller data structure
 * @comm_type: type of communication to configure
 */
static int stm32h7_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
{
	u32 mode;
	u32 cfg2_clrb = 0, cfg2_setb = 0;

	if (comm_type == SPI_3WIRE_RX) {
		mode = STM32H7_SPI_HALF_DUPLEX;
		stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
	} else if (comm_type == SPI_3WIRE_TX) {
		mode = STM32H7_SPI_HALF_DUPLEX;
		stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
	} else if (comm_type == SPI_SIMPLEX_RX) {
		mode = STM32H7_SPI_SIMPLEX_RX;
	} else if (comm_type == SPI_SIMPLEX_TX) {
		mode = STM32H7_SPI_SIMPLEX_TX;
	} else {
		mode = STM32H7_SPI_FULL_DUPLEX;
	}

	cfg2_clrb |= STM32H7_SPI_CFG2_COMM;
	cfg2_setb |= FIELD_PREP(STM32H7_SPI_CFG2_COMM, mode);

	writel_relaxed(
		(readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
		 ~cfg2_clrb) | cfg2_setb,
		spi->base + STM32H7_SPI_CFG2);

	return 0;
}

/**
 * stm32h7_spi_data_idleness - configure minimum time delay inserted between two
 *			       consecutive data frames in host mode
 * @spi: pointer to the spi controller data structure
 * @xfer: pointer to spi transfer
 */
static void stm32h7_spi_data_idleness(struct stm32_spi *spi, struct spi_transfer *xfer)
{
	u32 cfg2_clrb = 0, cfg2_setb = 0;
	u32 len = xfer->len;
	u32 spi_delay_ns;

	spi_delay_ns = spi_delay_to_ns(&xfer->word_delay, xfer);

	if (spi->cur_midi != 0) {
		dev_warn(spi->dev, "st,spi-midi-ns DT property is deprecated\n");
		if (spi_delay_ns) {
			dev_warn(spi->dev, "Overriding st,spi-midi-ns with word_delay_ns %d\n",
				 spi_delay_ns);
			spi->cur_midi = spi_delay_ns;
		}
	} else {
		spi->cur_midi = spi_delay_ns;
	}

	cfg2_clrb |= STM32H7_SPI_CFG2_MIDI;
	if ((len > 1) && (spi->cur_midi > 0)) {
		u32 sck_period_ns = DIV_ROUND_UP(NSEC_PER_SEC, spi->cur_speed);
		u32 midi = DIV_ROUND_UP(spi->cur_midi, sck_period_ns);

		if ((spi->cur_bpw + midi) < 8)
			midi = 8 - spi->cur_bpw;

		midi = min_t(u32, midi, FIELD_MAX(STM32H7_SPI_CFG2_MIDI));

		dev_dbg(spi->dev, "period=%dns, midi=%d(=%dns)\n",
			sck_period_ns, midi, midi * sck_period_ns);
		cfg2_setb |= FIELD_PREP(STM32H7_SPI_CFG2_MIDI, midi);
	}

	writel_relaxed((readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
			~cfg2_clrb) | cfg2_setb,
		       spi->base + STM32H7_SPI_CFG2);
}

/**
 * stm32h7_spi_number_of_data - configure number of data at current transfer
 * @spi: pointer to the spi controller data structure
 * @nb_words: transfer length (in words)
 */
static int stm32h7_spi_number_of_data(struct stm32_spi *spi, u32 nb_words)
{
	if (nb_words <= spi->t_size_max) {
		writel_relaxed(FIELD_PREP(STM32H7_SPI_CR2_TSIZE, nb_words),
			       spi->base + STM32H7_SPI_CR2);
	} else {
		return -EMSGSIZE;
	}

	return 0;
}

/**
 * stm32_spi_transfer_one_setup - common setup to transfer a single
 *				  spi_transfer either using DMA or
 *				  interrupts.
 * @spi: pointer to the spi controller data structure
 * @spi_dev: pointer to the spi device
 * @transfer: pointer to spi transfer
 */
static int stm32_spi_transfer_one_setup(struct stm32_spi *spi,
					struct spi_device *spi_dev,
					struct spi_transfer *transfer)
{
	unsigned long flags;
	unsigned int comm_type;
	int nb_words, ret = 0;
	int mbr;

	spin_lock_irqsave(&spi->lock, flags);

	spi->cur_xferlen = transfer->len;

	spi->cur_bpw = transfer->bits_per_word;
	spi->cfg->set_bpw(spi);

	if (spi_dev->mode & SPI_READY && spi->cur_bpw < 8) {
		writel_relaxed(readl_relaxed(spi->base + spi->cfg->regs->rdy_en.reg) &
				~spi->cfg->regs->rdy_en.mask,
					spi->base + spi->cfg->regs->rdy_en.reg);
		dev_dbg(spi->dev, "RDY logic disabled as bits per word < 8\n");
	}

	/* Update spi->cur_speed with real clock speed */
	if (STM32_SPI_HOST_MODE(spi)) {
		mbr = stm32_spi_prepare_mbr(spi, transfer->speed_hz,
					    spi->cfg->baud_rate_div_min,
					    spi->cfg->baud_rate_div_max);
		if (mbr < 0) {
			ret = mbr;
			goto out;
		}

		transfer->speed_hz = spi->cur_speed;
		stm32_spi_set_mbr(spi, mbr);
	}

	comm_type = stm32_spi_communication_type(spi_dev, transfer);
	ret = spi->cfg->set_mode(spi, comm_type);
	if (ret < 0)
		goto out;

	spi->cur_comm = comm_type;

	if (STM32_SPI_HOST_MODE(spi) && spi->cfg->set_data_idleness)
		spi->cfg->set_data_idleness(spi, transfer);

	if (spi->cur_bpw <= 8)
		nb_words = transfer->len;
	else if (spi->cur_bpw <= 16)
		nb_words = DIV_ROUND_UP(transfer->len * 8, 16);
	else
		nb_words = DIV_ROUND_UP(transfer->len * 8, 32);

	if (spi->cfg->set_number_of_data) {
		ret = spi->cfg->set_number_of_data(spi, nb_words);
		if (ret < 0)
			goto out;
	}

	dev_dbg(spi->dev, "transfer communication mode set to %d\n",
		spi->cur_comm);
	dev_dbg(spi->dev,
		"data frame of %d-bit, data packet of %d data frames\n",
		spi->cur_bpw, spi->cur_fthlv);
	if (STM32_SPI_HOST_MODE(spi))
		dev_dbg(spi->dev, "speed set to %dHz\n", spi->cur_speed);
	dev_dbg(spi->dev, "transfer of %d bytes (%d data frames)\n",
		spi->cur_xferlen, nb_words);
	dev_dbg(spi->dev, "dma %s\n",
		(spi->cur_usedma) ? "enabled" : "disabled");

out:
	spin_unlock_irqrestore(&spi->lock, flags);

	return ret;
}

/**
 * stm32_spi_can_poll - detect if poll based transfer is appropriate
 * @spi: pointer to the spi controller data structure
 *
 * Returns true is poll is more appropriate, false otherwise.
 */
static bool stm32_spi_can_poll(struct stm32_spi *spi)
{
	unsigned long hz_per_byte, byte_limit;

	/* Evaluate the transfer time and use polling if applicable */
	hz_per_byte = polling_limit_us ?
		      DIV_ROUND_UP(8 * USEC_PER_SEC, polling_limit_us) : 0;
	byte_limit = hz_per_byte ? spi->cur_speed / hz_per_byte : 1;

	return (spi->cur_xferlen < byte_limit) ? true : false;
}

/**
 * stm32_spi_transfer_one - transfer a single spi_transfer
 * @ctrl: controller interface
 * @spi_dev: pointer to the spi device
 * @transfer: pointer to spi transfer
 *
 * It must return 0 if the transfer is finished or 1 if the transfer is still
 * in progress.
 */
static int stm32_spi_transfer_one(struct spi_controller *ctrl,
				  struct spi_device *spi_dev,
				  struct spi_transfer *transfer)
{
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	int ret;

	spi->tx_buf = transfer->tx_buf;
	spi->rx_buf = transfer->rx_buf;
	spi->tx_len = spi->tx_buf ? transfer->len : 0;
	spi->rx_len = spi->rx_buf ? transfer->len : 0;

	spi->cur_usedma = (ctrl->can_dma &&
			   ctrl->can_dma(ctrl, spi_dev, transfer));

	ret = stm32_spi_transfer_one_setup(spi, spi_dev, transfer);
	if (ret) {
		dev_err(spi->dev, "SPI transfer setup failed\n");
		return ret;
	}

	if (spi->cur_usedma)
		return stm32_spi_transfer_one_dma(spi, transfer);
	else if (spi->cfg->transfer_one_poll && stm32_spi_can_poll(spi))
		return spi->cfg->transfer_one_poll(spi);
	else
		return spi->cfg->transfer_one_irq(spi);
}

/**
 * stm32_spi_unprepare_msg - relax the hardware
 * @ctrl: controller interface
 * @msg: pointer to the spi message
 */
static int stm32_spi_unprepare_msg(struct spi_controller *ctrl,
				   struct spi_message *msg)
{
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	spi->cfg->disable(spi);

	if (spi->sram_rx_buf)
		memset(spi->sram_rx_buf, 0, spi->sram_rx_buf_size);

	return 0;
}

/**
 * stm32fx_spi_config - Configure SPI controller as SPI host
 * @spi: pointer to the spi controller data structure
 */
static int stm32fx_spi_config(struct stm32_spi *spi)
{
	unsigned long flags;

	spin_lock_irqsave(&spi->lock, flags);

	/* Ensure I2SMOD bit is kept cleared */
	stm32_spi_clr_bits(spi, STM32FX_SPI_I2SCFGR,
			   STM32FX_SPI_I2SCFGR_I2SMOD);

	/*
	 * - SS input value high
	 * - transmitter half duplex direction
	 * - Set the host mode (default Motorola mode)
	 * - Consider 1 host/n targets configuration and
	 *   SS input value is determined by the SSI bit
	 */
	stm32_spi_set_bits(spi, STM32FX_SPI_CR1, STM32FX_SPI_CR1_SSI |
						 STM32FX_SPI_CR1_BIDIOE |
						 STM32FX_SPI_CR1_MSTR |
						 STM32FX_SPI_CR1_SSM);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 0;
}

/**
 * stm32h7_spi_config - Configure SPI controller
 * @spi: pointer to the spi controller data structure
 */
static int stm32h7_spi_config(struct stm32_spi *spi)
{
	unsigned long flags;
	u32 cr1 = 0, cfg2 = 0;

	spin_lock_irqsave(&spi->lock, flags);

	/* Ensure I2SMOD bit is kept cleared */
	stm32_spi_clr_bits(spi, STM32H7_SPI_I2SCFGR,
			   STM32H7_SPI_I2SCFGR_I2SMOD);

	if (STM32_SPI_DEVICE_MODE(spi)) {
		/* Use native device select */
		cfg2 &= ~STM32H7_SPI_CFG2_SSM;
	} else {
		/*
		 * - Transmitter half duplex direction
		 * - Automatic communication suspend when RX-Fifo is full
		 * - SS input value high
		 */
		cr1 |= STM32H7_SPI_CR1_HDDIR | STM32H7_SPI_CR1_MASRX | STM32H7_SPI_CR1_SSI;

		/*
		 * - Set the host mode (default Motorola mode)
		 * - Consider 1 host/n devices configuration and
		 *   SS input value is determined by the SSI bit
		 * - keep control of all associated GPIOs
		 */
		cfg2 |= STM32H7_SPI_CFG2_MASTER | STM32H7_SPI_CFG2_SSM | STM32H7_SPI_CFG2_AFCNTR;
	}

	stm32_spi_set_bits(spi, STM32H7_SPI_CR1, cr1);
	stm32_spi_set_bits(spi, STM32H7_SPI_CFG2, cfg2);

	spin_unlock_irqrestore(&spi->lock, flags);

	return 0;
}

static const struct stm32_spi_cfg stm32f4_spi_cfg = {
	.regs = &stm32fx_spi_regspec,
	.get_bpw_mask = stm32f4_spi_get_bpw_mask,
	.disable = stm32fx_spi_disable,
	.config = stm32fx_spi_config,
	.set_bpw = stm32f4_spi_set_bpw,
	.set_mode = stm32fx_spi_set_mode,
	.write_tx = stm32f4_spi_write_tx,
	.read_rx = stm32f4_spi_read_rx,
	.transfer_one_dma_start = stm32fx_spi_transfer_one_dma_start,
	.dma_tx_cb = stm32fx_spi_dma_tx_cb,
	.dma_rx_cb = stm32_spi_dma_rx_cb,
	.transfer_one_irq = stm32fx_spi_transfer_one_irq,
	.irq_handler_event = stm32fx_spi_irq_event,
	.irq_handler_thread = stm32fx_spi_irq_thread,
	.baud_rate_div_min = STM32FX_SPI_BR_DIV_MIN,
	.baud_rate_div_max = STM32FX_SPI_BR_DIV_MAX,
	.has_fifo = false,
	.has_device_mode = false,
	.flags = SPI_CONTROLLER_MUST_TX,
};

static const struct stm32_spi_cfg stm32f7_spi_cfg = {
	.regs = &stm32fx_spi_regspec,
	.get_bpw_mask = stm32f7_spi_get_bpw_mask,
	.disable = stm32fx_spi_disable,
	.config = stm32fx_spi_config,
	.set_bpw = stm32f7_spi_set_bpw,
	.set_mode = stm32fx_spi_set_mode,
	.write_tx = stm32f7_spi_write_tx,
	.read_rx = stm32f7_spi_read_rx,
	.transfer_one_dma_start = stm32f7_spi_transfer_one_dma_start,
	.dma_tx_cb = stm32fx_spi_dma_tx_cb,
	.dma_rx_cb = stm32_spi_dma_rx_cb,
	.transfer_one_irq = stm32fx_spi_transfer_one_irq,
	.irq_handler_event = stm32fx_spi_irq_event,
	.irq_handler_thread = stm32fx_spi_irq_thread,
	.baud_rate_div_min = STM32FX_SPI_BR_DIV_MIN,
	.baud_rate_div_max = STM32FX_SPI_BR_DIV_MAX,
	.has_fifo = false,
	.flags = SPI_CONTROLLER_MUST_TX,
};

static const struct stm32_spi_cfg stm32h7_spi_cfg = {
	.regs = &stm32h7_spi_regspec,
	.get_fifo_size = stm32h7_spi_get_fifo_size,
	.get_bpw_mask = stm32h7_spi_get_bpw_mask,
	.disable = stm32h7_spi_disable,
	.config = stm32h7_spi_config,
	.set_bpw = stm32h7_spi_set_bpw,
	.set_mode = stm32h7_spi_set_mode,
	.set_data_idleness = stm32h7_spi_data_idleness,
	.set_number_of_data = stm32h7_spi_number_of_data,
	.write_tx = stm32h7_spi_write_txfifo,
	.read_rx = stm32h7_spi_read_rxfifo,
	.transfer_one_dma_start = stm32h7_spi_transfer_one_dma_start,
	.dma_rx_cb = stm32_spi_dma_rx_cb,
	/*
	 * dma_tx_cb is not necessary since in case of TX, dma is followed by
	 * SPI access hence handling is performed within the SPI interrupt
	 */
	.transfer_one_irq = stm32h7_spi_transfer_one_irq,
	.transfer_one_poll = stm32h7_spi_transfer_one_poll,
	.irq_handler_thread = stm32h7_spi_irq_thread,
	.baud_rate_div_min = STM32H7_SPI_MBR_DIV_MIN,
	.baud_rate_div_max = STM32H7_SPI_MBR_DIV_MAX,
	.has_fifo = true,
	.has_device_mode = true,
};

/*
 * STM32MP2 is compatible with the STM32H7 except:
 * - enforce the DMA maxburst value to 1
 * - spi8 have limited feature set (TSIZE_MAX = 1024, BPW of 8 OR 16)
 */
static const struct stm32_spi_cfg stm32mp25_spi_cfg = {
	.regs = &stm32mp25_spi_regspec,
	.get_fifo_size = stm32h7_spi_get_fifo_size,
	.get_bpw_mask = stm32mp25_spi_get_bpw_mask,
	.disable = stm32h7_spi_disable,
	.config = stm32h7_spi_config,
	.set_bpw = stm32h7_spi_set_bpw,
	.set_mode = stm32h7_spi_set_mode,
	.set_data_idleness = stm32h7_spi_data_idleness,
	.set_number_of_data = stm32h7_spi_number_of_data,
	.transfer_one_dma_start = stm32h7_spi_transfer_one_dma_start,
	.dma_rx_cb = stm32_spi_dma_rx_cb,
	/*
	 * dma_tx_cb is not necessary since in case of TX, dma is followed by
	 * SPI access hence handling is performed within the SPI interrupt
	 */
	.transfer_one_irq = stm32h7_spi_transfer_one_irq,
	.transfer_one_poll = stm32h7_spi_transfer_one_poll,
	.irq_handler_thread = stm32h7_spi_irq_thread,
	.baud_rate_div_min = STM32H7_SPI_MBR_DIV_MIN,
	.baud_rate_div_max = STM32H7_SPI_MBR_DIV_MAX,
	.has_fifo = true,
	.prevent_dma_burst = true,
	.has_device_mode = true,
};

static const struct of_device_id stm32_spi_of_match[] = {
	{ .compatible = "st,stm32mp25-spi", .data = (void *)&stm32mp25_spi_cfg },
	{ .compatible = "st,stm32h7-spi", .data = (void *)&stm32h7_spi_cfg },
	{ .compatible = "st,stm32f4-spi", .data = (void *)&stm32f4_spi_cfg },
	{ .compatible = "st,stm32f7-spi", .data = (void *)&stm32f7_spi_cfg },
	{},
};
MODULE_DEVICE_TABLE(of, stm32_spi_of_match);

static int stm32h7_spi_device_abort(struct spi_controller *ctrl)
{
	spi_finalize_current_transfer(ctrl);
	return 0;
}

static int stm32_spi_probe(struct platform_device *pdev)
{
	struct spi_controller *ctrl;
	struct stm32_spi *spi;
	struct resource *res;
	struct reset_control *rst;
	struct device_node *np = pdev->dev.of_node;
	const struct stm32_spi_cfg *cfg;
	bool device_mode;
	int ret;

	cfg = of_device_get_match_data(&pdev->dev);
	if (!cfg) {
		dev_err(&pdev->dev, "Failed to get match data for platform\n");
		return -ENODEV;
	}

	device_mode = of_property_read_bool(np, "spi-slave");
	if (!cfg->has_device_mode && device_mode) {
		dev_err(&pdev->dev, "spi-slave not supported\n");
		return -EPERM;
	}

	if (device_mode)
		ctrl = devm_spi_alloc_target(&pdev->dev, sizeof(struct stm32_spi));
	else
		ctrl = devm_spi_alloc_host(&pdev->dev, sizeof(struct stm32_spi));
	if (!ctrl) {
		dev_err(&pdev->dev, "spi controller allocation failed\n");
		return -ENOMEM;
	}
	platform_set_drvdata(pdev, ctrl);

	spi = spi_controller_get_devdata(ctrl);
	spi->dev = &pdev->dev;
	spi->ctrl = ctrl;
	spi->device_mode = device_mode;
	spin_lock_init(&spi->lock);

	spi->cfg = cfg;

	spi->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
	if (IS_ERR(spi->base))
		return PTR_ERR(spi->base);

	spi->phys_addr = (dma_addr_t)res->start;

	spi->irq = platform_get_irq(pdev, 0);
	if (spi->irq <= 0)
		return spi->irq;

	ret = devm_request_threaded_irq(&pdev->dev, spi->irq,
					spi->cfg->irq_handler_event,
					spi->cfg->irq_handler_thread,
					IRQF_ONESHOT, pdev->name, ctrl);
	if (ret) {
		dev_err(&pdev->dev, "irq%d request failed: %d\n", spi->irq,
			ret);
		return ret;
	}

	spi->clk = devm_clk_get(&pdev->dev, NULL);
	if (IS_ERR(spi->clk)) {
		ret = PTR_ERR(spi->clk);
		dev_err(&pdev->dev, "clk get failed: %d\n", ret);
		return ret;
	}

	ret = clk_prepare_enable(spi->clk);
	if (ret) {
		dev_err(&pdev->dev, "clk enable failed: %d\n", ret);
		return ret;
	}
	spi->clk_rate = clk_get_rate(spi->clk);
	if (!spi->clk_rate) {
		dev_err(&pdev->dev, "clk rate = 0\n");
		ret = -EINVAL;
		goto err_clk_disable;
	}

	rst = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL);
	if (rst) {
		if (IS_ERR(rst)) {
			ret = dev_err_probe(&pdev->dev, PTR_ERR(rst),
					    "failed to get reset\n");
			goto err_clk_disable;
		}

		reset_control_assert(rst);
		udelay(2);
		reset_control_deassert(rst);
	}

	if (spi->cfg->has_fifo)
		spi->fifo_size = spi->cfg->get_fifo_size(spi);

	spi->feature_set = STM32_SPI_FEATURE_FULL;
	if (spi->cfg->regs->fullcfg.reg) {
		spi->feature_set =
			FIELD_GET(STM32MP25_SPI_HWCFGR1_FULLCFG,
				  readl_relaxed(spi->base + spi->cfg->regs->fullcfg.reg));

		dev_dbg(spi->dev, "%s feature set\n",
			spi->feature_set == STM32_SPI_FEATURE_FULL ? "full" : "limited");
	}

	/* Only for STM32H7 and after */
	spi->t_size_max = spi->feature_set == STM32_SPI_FEATURE_FULL ?
				STM32H7_SPI_TSIZE_MAX :
				STM32MP25_SPI_TSIZE_MAX_LIMITED;
	dev_dbg(spi->dev, "one message max size %d\n", spi->t_size_max);

	ret = spi->cfg->config(spi);
	if (ret) {
		dev_err(&pdev->dev, "controller configuration failed: %d\n",
			ret);
		goto err_clk_disable;
	}

	ctrl->auto_runtime_pm = true;
	ctrl->bus_num = pdev->id;
	ctrl->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST |
			  SPI_3WIRE | SPI_READY;
	ctrl->bits_per_word_mask = spi->cfg->get_bpw_mask(spi);
	ctrl->max_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_min;
	ctrl->min_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_max;
	ctrl->use_gpio_descriptors = true;
	ctrl->optimize_message = stm32_spi_optimize_message;
	ctrl->prepare_message = stm32_spi_prepare_msg;
	ctrl->transfer_one = stm32_spi_transfer_one;
	ctrl->unprepare_message = stm32_spi_unprepare_msg;
	ctrl->flags = spi->cfg->flags;
	if (STM32_SPI_DEVICE_MODE(spi))
		ctrl->target_abort = stm32h7_spi_device_abort;

	spi->dma_tx = dma_request_chan(spi->dev, "tx");
	if (IS_ERR(spi->dma_tx)) {
		ret = PTR_ERR(spi->dma_tx);
		if (ret == -ENODEV) {
			dev_info(&pdev->dev, "tx dma disabled\n");
			spi->dma_tx = NULL;
		} else {
			dev_err_probe(&pdev->dev, ret, "failed to request tx dma channel\n");
			goto err_clk_disable;
		}
	} else {
		ctrl->dma_tx = spi->dma_tx;
	}

	spi->dma_rx = dma_request_chan(spi->dev, "rx");
	if (IS_ERR(spi->dma_rx)) {
		ret = PTR_ERR(spi->dma_rx);
		if (ret == -ENODEV) {
			dev_info(&pdev->dev, "rx dma disabled\n");
			spi->dma_rx = NULL;
		} else {
			dev_err_probe(&pdev->dev, ret, "failed to request rx dma channel\n");
			goto err_dma_release;
		}
	} else {
		ctrl->dma_rx = spi->dma_rx;
	}

	if (spi->dma_tx || spi->dma_rx)
		ctrl->can_dma = stm32_spi_can_dma;

	spi->sram_pool = of_gen_pool_get(pdev->dev.of_node, "sram", 0);
	if (spi->sram_pool) {
		spi->sram_rx_buf_size = gen_pool_size(spi->sram_pool);
		dev_info(&pdev->dev, "SRAM pool: %zu KiB for RX DMA/MDMA chaining\n",
			 spi->sram_rx_buf_size / 1024);
		spi->sram_rx_buf = gen_pool_dma_zalloc(spi->sram_pool, spi->sram_rx_buf_size,
						       &spi->sram_dma_rx_buf);
		if (!spi->sram_rx_buf) {
			dev_err(&pdev->dev, "failed to allocate SRAM buffer\n");
		} else {
			spi->mdma_rx = dma_request_chan(spi->dev, "rxm2m");
			if (IS_ERR(spi->mdma_rx)) {
				ret = PTR_ERR(spi->mdma_rx);
				spi->mdma_rx = NULL;
				if (ret == -EPROBE_DEFER) {
					goto err_pool_free;
				} else {
					gen_pool_free(spi->sram_pool,
						      (unsigned long)spi->sram_rx_buf,
						      spi->sram_rx_buf_size);
					dev_warn(&pdev->dev,
						 "failed to request rx mdma channel, DMA only\n");
				}
			}
		}
	}

	pm_runtime_set_autosuspend_delay(&pdev->dev,
					 STM32_SPI_AUTOSUSPEND_DELAY);
	pm_runtime_use_autosuspend(&pdev->dev);
	pm_runtime_set_active(&pdev->dev);
	pm_runtime_get_noresume(&pdev->dev);
	pm_runtime_enable(&pdev->dev);

	ret = spi_register_controller(ctrl);
	if (ret) {
		dev_err(&pdev->dev, "spi controller registration failed: %d\n",
			ret);
		goto err_pm_disable;
	}

	pm_runtime_put_autosuspend(&pdev->dev);

	dev_info(&pdev->dev, "driver initialized (%s mode)\n",
		 STM32_SPI_HOST_MODE(spi) ? "host" : "device");

	return 0;

err_pm_disable:
	pm_runtime_disable(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_dont_use_autosuspend(&pdev->dev);

	if (spi->mdma_rx)
		dma_release_channel(spi->mdma_rx);
err_pool_free:
	if (spi->sram_pool)
		gen_pool_free(spi->sram_pool, (unsigned long)spi->sram_rx_buf,
			      spi->sram_rx_buf_size);
err_dma_release:
	if (spi->dma_tx)
		dma_release_channel(spi->dma_tx);
	if (spi->dma_rx)
		dma_release_channel(spi->dma_rx);
err_clk_disable:
	clk_disable_unprepare(spi->clk);

	return ret;
}

static void stm32_spi_remove(struct platform_device *pdev)
{
	struct spi_controller *ctrl = platform_get_drvdata(pdev);
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	pm_runtime_get_sync(&pdev->dev);

	spi_unregister_controller(ctrl);
	spi->cfg->disable(spi);

	pm_runtime_disable(&pdev->dev);
	pm_runtime_put_noidle(&pdev->dev);
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_dont_use_autosuspend(&pdev->dev);

	if (ctrl->dma_tx)
		dma_release_channel(ctrl->dma_tx);
	if (ctrl->dma_rx)
		dma_release_channel(ctrl->dma_rx);
	if (spi->mdma_rx)
		dma_release_channel(spi->mdma_rx);
	if (spi->sram_rx_buf)
		gen_pool_free(spi->sram_pool, (unsigned long)spi->sram_rx_buf,
			      spi->sram_rx_buf_size);

	clk_disable_unprepare(spi->clk);


	pinctrl_pm_select_sleep_state(&pdev->dev);
}

static int stm32_spi_runtime_suspend(struct device *dev)
{
	struct spi_controller *ctrl = dev_get_drvdata(dev);
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);

	clk_disable_unprepare(spi->clk);

	return pinctrl_pm_select_sleep_state(dev);
}

static int stm32_spi_runtime_resume(struct device *dev)
{
	struct spi_controller *ctrl = dev_get_drvdata(dev);
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	int ret;

	ret = pinctrl_pm_select_default_state(dev);
	if (ret)
		return ret;

	return clk_prepare_enable(spi->clk);
}

static int stm32_spi_suspend(struct device *dev)
{
	struct spi_controller *ctrl = dev_get_drvdata(dev);
	int ret;

	ret = spi_controller_suspend(ctrl);
	if (ret)
		return ret;

	return pm_runtime_force_suspend(dev);
}

static int stm32_spi_resume(struct device *dev)
{
	struct spi_controller *ctrl = dev_get_drvdata(dev);
	struct stm32_spi *spi = spi_controller_get_devdata(ctrl);
	int ret;

	ret = pm_runtime_force_resume(dev);
	if (ret)
		return ret;

	ret = spi_controller_resume(ctrl);
	if (ret) {
		clk_disable_unprepare(spi->clk);
		return ret;
	}

	ret = pm_runtime_resume_and_get(dev);
	if (ret < 0) {
		dev_err(dev, "Unable to power device:%d\n", ret);
		return ret;
	}

	spi->cfg->config(spi);

	pm_runtime_put_autosuspend(dev);

	return 0;
}

static const struct dev_pm_ops stm32_spi_pm_ops = {
	SYSTEM_SLEEP_PM_OPS(stm32_spi_suspend, stm32_spi_resume)
	RUNTIME_PM_OPS(stm32_spi_runtime_suspend, stm32_spi_runtime_resume, NULL)
};

static struct platform_driver stm32_spi_driver = {
	.probe = stm32_spi_probe,
	.remove = stm32_spi_remove,
	.driver = {
		.name = DRIVER_NAME,
		.pm = pm_ptr(&stm32_spi_pm_ops),
		.of_match_table = stm32_spi_of_match,
	},
};

module_platform_driver(stm32_spi_driver);

MODULE_ALIAS("platform:" DRIVER_NAME);
MODULE_DESCRIPTION("STMicroelectronics STM32 SPI Controller driver");
MODULE_AUTHOR("Amelie Delaunay <amelie.delaunay@st.com>");
MODULE_LICENSE("GPL v2");