1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Xilinx Zynq GPIO device driver
4 *
5 * Copyright (C) 2009 - 2014 Xilinx, Inc.
6 */
7
8 #include <linux/bitops.h>
9 #include <linux/clk.h>
10 #include <linux/gpio/driver.h>
11 #include <linux/init.h>
12 #include <linux/interrupt.h>
13 #include <linux/spinlock.h>
14 #include <linux/io.h>
15 #include <linux/module.h>
16 #include <linux/platform_device.h>
17 #include <linux/pm_runtime.h>
18 #include <linux/of.h>
19
20 #define DRIVER_NAME "zynq-gpio"
21
22 /* Maximum banks */
23 #define ZYNQ_GPIO_MAX_BANK 4
24 #define ZYNQMP_GPIO_MAX_BANK 6
25 #define VERSAL_GPIO_MAX_BANK 4
26 #define PMC_GPIO_MAX_BANK 5
27 #define VERSAL_UNUSED_BANKS 2
28
29 #define ZYNQ_GPIO_BANK0_NGPIO 32
30 #define ZYNQ_GPIO_BANK1_NGPIO 22
31 #define ZYNQ_GPIO_BANK2_NGPIO 32
32 #define ZYNQ_GPIO_BANK3_NGPIO 32
33
34 #define ZYNQMP_GPIO_BANK0_NGPIO 26
35 #define ZYNQMP_GPIO_BANK1_NGPIO 26
36 #define ZYNQMP_GPIO_BANK2_NGPIO 26
37 #define ZYNQMP_GPIO_BANK3_NGPIO 32
38 #define ZYNQMP_GPIO_BANK4_NGPIO 32
39 #define ZYNQMP_GPIO_BANK5_NGPIO 32
40
41 #define ZYNQ_GPIO_NR_GPIOS 118
42 #define ZYNQMP_GPIO_NR_GPIOS 174
43
44 #define ZYNQ_GPIO_BANK0_PIN_MIN(str) 0
45 #define ZYNQ_GPIO_BANK0_PIN_MAX(str) (ZYNQ_GPIO_BANK0_PIN_MIN(str) + \
46 ZYNQ##str##_GPIO_BANK0_NGPIO - 1)
47 #define ZYNQ_GPIO_BANK1_PIN_MIN(str) (ZYNQ_GPIO_BANK0_PIN_MAX(str) + 1)
48 #define ZYNQ_GPIO_BANK1_PIN_MAX(str) (ZYNQ_GPIO_BANK1_PIN_MIN(str) + \
49 ZYNQ##str##_GPIO_BANK1_NGPIO - 1)
50 #define ZYNQ_GPIO_BANK2_PIN_MIN(str) (ZYNQ_GPIO_BANK1_PIN_MAX(str) + 1)
51 #define ZYNQ_GPIO_BANK2_PIN_MAX(str) (ZYNQ_GPIO_BANK2_PIN_MIN(str) + \
52 ZYNQ##str##_GPIO_BANK2_NGPIO - 1)
53 #define ZYNQ_GPIO_BANK3_PIN_MIN(str) (ZYNQ_GPIO_BANK2_PIN_MAX(str) + 1)
54 #define ZYNQ_GPIO_BANK3_PIN_MAX(str) (ZYNQ_GPIO_BANK3_PIN_MIN(str) + \
55 ZYNQ##str##_GPIO_BANK3_NGPIO - 1)
56 #define ZYNQ_GPIO_BANK4_PIN_MIN(str) (ZYNQ_GPIO_BANK3_PIN_MAX(str) + 1)
57 #define ZYNQ_GPIO_BANK4_PIN_MAX(str) (ZYNQ_GPIO_BANK4_PIN_MIN(str) + \
58 ZYNQ##str##_GPIO_BANK4_NGPIO - 1)
59 #define ZYNQ_GPIO_BANK5_PIN_MIN(str) (ZYNQ_GPIO_BANK4_PIN_MAX(str) + 1)
60 #define ZYNQ_GPIO_BANK5_PIN_MAX(str) (ZYNQ_GPIO_BANK5_PIN_MIN(str) + \
61 ZYNQ##str##_GPIO_BANK5_NGPIO - 1)
62
63 /* Register offsets for the GPIO device */
64 /* LSW Mask & Data -WO */
65 #define ZYNQ_GPIO_DATA_LSW_OFFSET(BANK) (0x000 + (8 * BANK))
66 /* MSW Mask & Data -WO */
67 #define ZYNQ_GPIO_DATA_MSW_OFFSET(BANK) (0x004 + (8 * BANK))
68 /* Data Register-RW */
69 #define ZYNQ_GPIO_DATA_OFFSET(BANK) (0x040 + (4 * BANK))
70 #define ZYNQ_GPIO_DATA_RO_OFFSET(BANK) (0x060 + (4 * BANK))
71 /* Direction mode reg-RW */
72 #define ZYNQ_GPIO_DIRM_OFFSET(BANK) (0x204 + (0x40 * BANK))
73 /* Output enable reg-RW */
74 #define ZYNQ_GPIO_OUTEN_OFFSET(BANK) (0x208 + (0x40 * BANK))
75 /* Interrupt mask reg-RO */
76 #define ZYNQ_GPIO_INTMASK_OFFSET(BANK) (0x20C + (0x40 * BANK))
77 /* Interrupt enable reg-WO */
78 #define ZYNQ_GPIO_INTEN_OFFSET(BANK) (0x210 + (0x40 * BANK))
79 /* Interrupt disable reg-WO */
80 #define ZYNQ_GPIO_INTDIS_OFFSET(BANK) (0x214 + (0x40 * BANK))
81 /* Interrupt status reg-RO */
82 #define ZYNQ_GPIO_INTSTS_OFFSET(BANK) (0x218 + (0x40 * BANK))
83 /* Interrupt type reg-RW */
84 #define ZYNQ_GPIO_INTTYPE_OFFSET(BANK) (0x21C + (0x40 * BANK))
85 /* Interrupt polarity reg-RW */
86 #define ZYNQ_GPIO_INTPOL_OFFSET(BANK) (0x220 + (0x40 * BANK))
87 /* Interrupt on any, reg-RW */
88 #define ZYNQ_GPIO_INTANY_OFFSET(BANK) (0x224 + (0x40 * BANK))
89
90 /* Disable all interrupts mask */
91 #define ZYNQ_GPIO_IXR_DISABLE_ALL 0xFFFFFFFF
92
93 /* Mid pin number of a bank */
94 #define ZYNQ_GPIO_MID_PIN_NUM 16
95
96 /* GPIO upper 16 bit mask */
97 #define ZYNQ_GPIO_UPPER_MASK 0xFFFF0000
98
99 /* set to differentiate zynq from zynqmp, 0=zynqmp, 1=zynq */
100 #define ZYNQ_GPIO_QUIRK_IS_ZYNQ BIT(0)
101 #define GPIO_QUIRK_DATA_RO_BUG BIT(1)
102 #define GPIO_QUIRK_VERSAL BIT(2)
103
104 struct gpio_regs {
105 u32 datamsw[ZYNQMP_GPIO_MAX_BANK];
106 u32 datalsw[ZYNQMP_GPIO_MAX_BANK];
107 u32 dirm[ZYNQMP_GPIO_MAX_BANK];
108 u32 outen[ZYNQMP_GPIO_MAX_BANK];
109 u32 int_en[ZYNQMP_GPIO_MAX_BANK];
110 u32 int_dis[ZYNQMP_GPIO_MAX_BANK];
111 u32 int_type[ZYNQMP_GPIO_MAX_BANK];
112 u32 int_polarity[ZYNQMP_GPIO_MAX_BANK];
113 u32 int_any[ZYNQMP_GPIO_MAX_BANK];
114 };
115
116 /**
117 * struct zynq_gpio - gpio device private data structure
118 * @chip: instance of the gpio_chip
119 * @base_addr: base address of the GPIO device
120 * @clk: clock resource for this controller
121 * @irq: interrupt for the GPIO device
122 * @p_data: pointer to platform data
123 * @context: context registers
124 * @dirlock: lock used for direction in/out synchronization
125 */
126 struct zynq_gpio {
127 struct gpio_chip chip;
128 void __iomem *base_addr;
129 struct clk *clk;
130 int irq;
131 const struct zynq_platform_data *p_data;
132 struct gpio_regs context;
133 spinlock_t dirlock; /* lock */
134 };
135
136 /**
137 * struct zynq_platform_data - zynq gpio platform data structure
138 * @label: string to store in gpio->label
139 * @quirks: Flags is used to identify the platform
140 * @ngpio: max number of gpio pins
141 * @max_bank: maximum number of gpio banks
142 * @bank_min: this array represents bank's min pin
143 * @bank_max: this array represents bank's max pin
144 */
145 struct zynq_platform_data {
146 const char *label;
147 u32 quirks;
148 u16 ngpio;
149 int max_bank;
150 int bank_min[ZYNQMP_GPIO_MAX_BANK];
151 int bank_max[ZYNQMP_GPIO_MAX_BANK];
152 };
153
154 static const struct irq_chip zynq_gpio_level_irqchip;
155 static const struct irq_chip zynq_gpio_edge_irqchip;
156
157 /**
158 * zynq_gpio_is_zynq - test if HW is zynq or zynqmp
159 * @gpio: Pointer to driver data struct
160 *
161 * Return: 0 if zynqmp, 1 if zynq.
162 */
zynq_gpio_is_zynq(struct zynq_gpio * gpio)163 static int zynq_gpio_is_zynq(struct zynq_gpio *gpio)
164 {
165 return !!(gpio->p_data->quirks & ZYNQ_GPIO_QUIRK_IS_ZYNQ);
166 }
167
168 /**
169 * gpio_data_ro_bug - test if HW bug exists or not
170 * @gpio: Pointer to driver data struct
171 *
172 * Return: 0 if bug doesnot exist, 1 if bug exists.
173 */
gpio_data_ro_bug(struct zynq_gpio * gpio)174 static int gpio_data_ro_bug(struct zynq_gpio *gpio)
175 {
176 return !!(gpio->p_data->quirks & GPIO_QUIRK_DATA_RO_BUG);
177 }
178
179 /**
180 * zynq_gpio_get_bank_pin - Get the bank number and pin number within that bank
181 * for a given pin in the GPIO device
182 * @pin_num: gpio pin number within the device
183 * @bank_num: an output parameter used to return the bank number of the gpio
184 * pin
185 * @bank_pin_num: an output parameter used to return pin number within a bank
186 * for the given gpio pin
187 * @gpio: gpio device data structure
188 *
189 * Returns the bank number and pin offset within the bank.
190 */
zynq_gpio_get_bank_pin(unsigned int pin_num,unsigned int * bank_num,unsigned int * bank_pin_num,struct zynq_gpio * gpio)191 static inline void zynq_gpio_get_bank_pin(unsigned int pin_num,
192 unsigned int *bank_num,
193 unsigned int *bank_pin_num,
194 struct zynq_gpio *gpio)
195 {
196 int bank;
197
198 for (bank = 0; bank < gpio->p_data->max_bank; bank++) {
199 if ((pin_num >= gpio->p_data->bank_min[bank]) &&
200 (pin_num <= gpio->p_data->bank_max[bank])) {
201 *bank_num = bank;
202 *bank_pin_num = pin_num -
203 gpio->p_data->bank_min[bank];
204 return;
205 }
206 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL)
207 bank = bank + VERSAL_UNUSED_BANKS;
208 }
209
210 /* default */
211 WARN(true, "invalid GPIO pin number: %u", pin_num);
212 *bank_num = 0;
213 *bank_pin_num = 0;
214 }
215
216 /**
217 * zynq_gpio_get_value - Get the state of the specified pin of GPIO device
218 * @chip: gpio_chip instance to be worked on
219 * @pin: gpio pin number within the device
220 *
221 * This function reads the state of the specified pin of the GPIO device.
222 *
223 * Return: 0 if the pin is low, 1 if pin is high.
224 */
zynq_gpio_get_value(struct gpio_chip * chip,unsigned int pin)225 static int zynq_gpio_get_value(struct gpio_chip *chip, unsigned int pin)
226 {
227 u32 data;
228 unsigned int bank_num, bank_pin_num;
229 struct zynq_gpio *gpio = gpiochip_get_data(chip);
230
231 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio);
232
233 if (gpio_data_ro_bug(gpio)) {
234 if (zynq_gpio_is_zynq(gpio)) {
235 if (bank_num <= 1) {
236 data = readl_relaxed(gpio->base_addr +
237 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
238 } else {
239 data = readl_relaxed(gpio->base_addr +
240 ZYNQ_GPIO_DATA_OFFSET(bank_num));
241 }
242 } else {
243 if (bank_num <= 2) {
244 data = readl_relaxed(gpio->base_addr +
245 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
246 } else {
247 data = readl_relaxed(gpio->base_addr +
248 ZYNQ_GPIO_DATA_OFFSET(bank_num));
249 }
250 }
251 } else {
252 data = readl_relaxed(gpio->base_addr +
253 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
254 }
255 return (data >> bank_pin_num) & 1;
256 }
257
258 /**
259 * zynq_gpio_set_value - Modify the state of the pin with specified value
260 * @chip: gpio_chip instance to be worked on
261 * @pin: gpio pin number within the device
262 * @state: value used to modify the state of the specified pin
263 *
264 * This function calculates the register offset (i.e to lower 16 bits or
265 * upper 16 bits) based on the given pin number and sets the state of a
266 * gpio pin to the specified value. The state is either 0 or non-zero.
267 */
zynq_gpio_set_value(struct gpio_chip * chip,unsigned int pin,int state)268 static void zynq_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
269 int state)
270 {
271 unsigned int reg_offset, bank_num, bank_pin_num;
272 struct zynq_gpio *gpio = gpiochip_get_data(chip);
273
274 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio);
275
276 if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) {
277 /* only 16 data bits in bit maskable reg */
278 bank_pin_num -= ZYNQ_GPIO_MID_PIN_NUM;
279 reg_offset = ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num);
280 } else {
281 reg_offset = ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num);
282 }
283
284 /*
285 * get the 32 bit value to be written to the mask/data register where
286 * the upper 16 bits is the mask and lower 16 bits is the data
287 */
288 state = !!state;
289 state = ~(1 << (bank_pin_num + ZYNQ_GPIO_MID_PIN_NUM)) &
290 ((state << bank_pin_num) | ZYNQ_GPIO_UPPER_MASK);
291
292 writel_relaxed(state, gpio->base_addr + reg_offset);
293 }
294
295 /**
296 * zynq_gpio_dir_in - Set the direction of the specified GPIO pin as input
297 * @chip: gpio_chip instance to be worked on
298 * @pin: gpio pin number within the device
299 *
300 * This function uses the read-modify-write sequence to set the direction of
301 * the gpio pin as input.
302 *
303 * Return: 0 always
304 */
zynq_gpio_dir_in(struct gpio_chip * chip,unsigned int pin)305 static int zynq_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
306 {
307 u32 reg;
308 unsigned int bank_num, bank_pin_num;
309 unsigned long flags;
310 struct zynq_gpio *gpio = gpiochip_get_data(chip);
311
312 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio);
313
314 /*
315 * On zynq bank 0 pins 7 and 8 are special and cannot be used
316 * as inputs.
317 */
318 if (zynq_gpio_is_zynq(gpio) && bank_num == 0 &&
319 (bank_pin_num == 7 || bank_pin_num == 8))
320 return -EINVAL;
321
322 /* clear the bit in direction mode reg to set the pin as input */
323 spin_lock_irqsave(&gpio->dirlock, flags);
324 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
325 reg &= ~BIT(bank_pin_num);
326 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
327 spin_unlock_irqrestore(&gpio->dirlock, flags);
328
329 return 0;
330 }
331
332 /**
333 * zynq_gpio_dir_out - Set the direction of the specified GPIO pin as output
334 * @chip: gpio_chip instance to be worked on
335 * @pin: gpio pin number within the device
336 * @state: value to be written to specified pin
337 *
338 * This function sets the direction of specified GPIO pin as output, configures
339 * the Output Enable register for the pin and uses zynq_gpio_set to set
340 * the state of the pin to the value specified.
341 *
342 * Return: 0 always
343 */
zynq_gpio_dir_out(struct gpio_chip * chip,unsigned int pin,int state)344 static int zynq_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
345 int state)
346 {
347 u32 reg;
348 unsigned int bank_num, bank_pin_num;
349 unsigned long flags;
350 struct zynq_gpio *gpio = gpiochip_get_data(chip);
351
352 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio);
353
354 /* set the GPIO pin as output */
355 spin_lock_irqsave(&gpio->dirlock, flags);
356 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
357 reg |= BIT(bank_pin_num);
358 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
359
360 /* configure the output enable reg for the pin */
361 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
362 reg |= BIT(bank_pin_num);
363 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
364 spin_unlock_irqrestore(&gpio->dirlock, flags);
365
366 /* set the state of the pin */
367 zynq_gpio_set_value(chip, pin, state);
368 return 0;
369 }
370
371 /**
372 * zynq_gpio_get_direction - Read the direction of the specified GPIO pin
373 * @chip: gpio_chip instance to be worked on
374 * @pin: gpio pin number within the device
375 *
376 * This function returns the direction of the specified GPIO.
377 *
378 * Return: GPIO_LINE_DIRECTION_OUT or GPIO_LINE_DIRECTION_IN
379 */
zynq_gpio_get_direction(struct gpio_chip * chip,unsigned int pin)380 static int zynq_gpio_get_direction(struct gpio_chip *chip, unsigned int pin)
381 {
382 u32 reg;
383 unsigned int bank_num, bank_pin_num;
384 struct zynq_gpio *gpio = gpiochip_get_data(chip);
385
386 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio);
387
388 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
389
390 if (reg & BIT(bank_pin_num))
391 return GPIO_LINE_DIRECTION_OUT;
392
393 return GPIO_LINE_DIRECTION_IN;
394 }
395
396 /**
397 * zynq_gpio_irq_mask - Disable the interrupts for a gpio pin
398 * @irq_data: per irq and chip data passed down to chip functions
399 *
400 * This function calculates gpio pin number from irq number and sets the
401 * bit in the Interrupt Disable register of the corresponding bank to disable
402 * interrupts for that pin.
403 */
zynq_gpio_irq_mask(struct irq_data * irq_data)404 static void zynq_gpio_irq_mask(struct irq_data *irq_data)
405 {
406 unsigned int device_pin_num, bank_num, bank_pin_num;
407 const unsigned long offset = irqd_to_hwirq(irq_data);
408 struct gpio_chip *chip = irq_data_get_irq_chip_data(irq_data);
409 struct zynq_gpio *gpio =
410 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data));
411
412 gpiochip_disable_irq(chip, offset);
413 device_pin_num = irq_data->hwirq;
414 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio);
415 writel_relaxed(BIT(bank_pin_num),
416 gpio->base_addr + ZYNQ_GPIO_INTDIS_OFFSET(bank_num));
417 }
418
419 /**
420 * zynq_gpio_irq_unmask - Enable the interrupts for a gpio pin
421 * @irq_data: irq data containing irq number of gpio pin for the interrupt
422 * to enable
423 *
424 * This function calculates the gpio pin number from irq number and sets the
425 * bit in the Interrupt Enable register of the corresponding bank to enable
426 * interrupts for that pin.
427 */
zynq_gpio_irq_unmask(struct irq_data * irq_data)428 static void zynq_gpio_irq_unmask(struct irq_data *irq_data)
429 {
430 unsigned int device_pin_num, bank_num, bank_pin_num;
431 const unsigned long offset = irqd_to_hwirq(irq_data);
432 struct gpio_chip *chip = irq_data_get_irq_chip_data(irq_data);
433 struct zynq_gpio *gpio =
434 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data));
435
436 gpiochip_enable_irq(chip, offset);
437 device_pin_num = irq_data->hwirq;
438 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio);
439 writel_relaxed(BIT(bank_pin_num),
440 gpio->base_addr + ZYNQ_GPIO_INTEN_OFFSET(bank_num));
441 }
442
443 /**
444 * zynq_gpio_irq_ack - Acknowledge the interrupt of a gpio pin
445 * @irq_data: irq data containing irq number of gpio pin for the interrupt
446 * to ack
447 *
448 * This function calculates gpio pin number from irq number and sets the bit
449 * in the Interrupt Status Register of the corresponding bank, to ACK the irq.
450 */
zynq_gpio_irq_ack(struct irq_data * irq_data)451 static void zynq_gpio_irq_ack(struct irq_data *irq_data)
452 {
453 unsigned int device_pin_num, bank_num, bank_pin_num;
454 struct zynq_gpio *gpio =
455 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data));
456
457 device_pin_num = irq_data->hwirq;
458 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio);
459 writel_relaxed(BIT(bank_pin_num),
460 gpio->base_addr + ZYNQ_GPIO_INTSTS_OFFSET(bank_num));
461 }
462
463 /**
464 * zynq_gpio_irq_enable - Enable the interrupts for a gpio pin
465 * @irq_data: irq data containing irq number of gpio pin for the interrupt
466 * to enable
467 *
468 * Clears the INTSTS bit and unmasks the given interrupt.
469 */
zynq_gpio_irq_enable(struct irq_data * irq_data)470 static void zynq_gpio_irq_enable(struct irq_data *irq_data)
471 {
472 /*
473 * The Zynq GPIO controller does not disable interrupt detection when
474 * the interrupt is masked and only disables the propagation of the
475 * interrupt. This means when the controller detects an interrupt
476 * condition while the interrupt is logically disabled it will propagate
477 * that interrupt event once the interrupt is enabled. This will cause
478 * the interrupt consumer to see spurious interrupts to prevent this
479 * first make sure that the interrupt is not asserted and then enable
480 * it.
481 */
482 zynq_gpio_irq_ack(irq_data);
483 zynq_gpio_irq_unmask(irq_data);
484 }
485
486 /**
487 * zynq_gpio_set_irq_type - Set the irq type for a gpio pin
488 * @irq_data: irq data containing irq number of gpio pin
489 * @type: interrupt type that is to be set for the gpio pin
490 *
491 * This function gets the gpio pin number and its bank from the gpio pin number
492 * and configures the INT_TYPE, INT_POLARITY and INT_ANY registers.
493 *
494 * Return: 0, negative error otherwise.
495 * TYPE-EDGE_RISING, INT_TYPE - 1, INT_POLARITY - 1, INT_ANY - 0;
496 * TYPE-EDGE_FALLING, INT_TYPE - 1, INT_POLARITY - 0, INT_ANY - 0;
497 * TYPE-EDGE_BOTH, INT_TYPE - 1, INT_POLARITY - NA, INT_ANY - 1;
498 * TYPE-LEVEL_HIGH, INT_TYPE - 0, INT_POLARITY - 1, INT_ANY - NA;
499 * TYPE-LEVEL_LOW, INT_TYPE - 0, INT_POLARITY - 0, INT_ANY - NA
500 */
zynq_gpio_set_irq_type(struct irq_data * irq_data,unsigned int type)501 static int zynq_gpio_set_irq_type(struct irq_data *irq_data, unsigned int type)
502 {
503 u32 int_type, int_pol, int_any;
504 unsigned int device_pin_num, bank_num, bank_pin_num;
505 struct zynq_gpio *gpio =
506 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data));
507
508 device_pin_num = irq_data->hwirq;
509 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio);
510
511 int_type = readl_relaxed(gpio->base_addr +
512 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num));
513 int_pol = readl_relaxed(gpio->base_addr +
514 ZYNQ_GPIO_INTPOL_OFFSET(bank_num));
515 int_any = readl_relaxed(gpio->base_addr +
516 ZYNQ_GPIO_INTANY_OFFSET(bank_num));
517
518 /*
519 * based on the type requested, configure the INT_TYPE, INT_POLARITY
520 * and INT_ANY registers
521 */
522 switch (type) {
523 case IRQ_TYPE_EDGE_RISING:
524 int_type |= BIT(bank_pin_num);
525 int_pol |= BIT(bank_pin_num);
526 int_any &= ~BIT(bank_pin_num);
527 break;
528 case IRQ_TYPE_EDGE_FALLING:
529 int_type |= BIT(bank_pin_num);
530 int_pol &= ~BIT(bank_pin_num);
531 int_any &= ~BIT(bank_pin_num);
532 break;
533 case IRQ_TYPE_EDGE_BOTH:
534 int_type |= BIT(bank_pin_num);
535 int_any |= BIT(bank_pin_num);
536 break;
537 case IRQ_TYPE_LEVEL_HIGH:
538 int_type &= ~BIT(bank_pin_num);
539 int_pol |= BIT(bank_pin_num);
540 break;
541 case IRQ_TYPE_LEVEL_LOW:
542 int_type &= ~BIT(bank_pin_num);
543 int_pol &= ~BIT(bank_pin_num);
544 break;
545 default:
546 return -EINVAL;
547 }
548
549 writel_relaxed(int_type,
550 gpio->base_addr + ZYNQ_GPIO_INTTYPE_OFFSET(bank_num));
551 writel_relaxed(int_pol,
552 gpio->base_addr + ZYNQ_GPIO_INTPOL_OFFSET(bank_num));
553 writel_relaxed(int_any,
554 gpio->base_addr + ZYNQ_GPIO_INTANY_OFFSET(bank_num));
555
556 if (type & IRQ_TYPE_LEVEL_MASK)
557 irq_set_chip_handler_name_locked(irq_data,
558 &zynq_gpio_level_irqchip,
559 handle_fasteoi_irq, NULL);
560 else
561 irq_set_chip_handler_name_locked(irq_data,
562 &zynq_gpio_edge_irqchip,
563 handle_level_irq, NULL);
564
565 return 0;
566 }
567
zynq_gpio_set_wake(struct irq_data * data,unsigned int on)568 static int zynq_gpio_set_wake(struct irq_data *data, unsigned int on)
569 {
570 struct zynq_gpio *gpio =
571 gpiochip_get_data(irq_data_get_irq_chip_data(data));
572
573 irq_set_irq_wake(gpio->irq, on);
574
575 return 0;
576 }
577
zynq_gpio_irq_reqres(struct irq_data * d)578 static int zynq_gpio_irq_reqres(struct irq_data *d)
579 {
580 struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
581 int ret;
582
583 ret = pm_runtime_resume_and_get(chip->parent);
584 if (ret < 0)
585 return ret;
586
587 return gpiochip_reqres_irq(chip, d->hwirq);
588 }
589
zynq_gpio_irq_relres(struct irq_data * d)590 static void zynq_gpio_irq_relres(struct irq_data *d)
591 {
592 struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
593
594 gpiochip_relres_irq(chip, d->hwirq);
595 pm_runtime_put(chip->parent);
596 }
597
598 /* irq chip descriptor */
599 static const struct irq_chip zynq_gpio_level_irqchip = {
600 .name = DRIVER_NAME,
601 .irq_enable = zynq_gpio_irq_enable,
602 .irq_eoi = zynq_gpio_irq_ack,
603 .irq_mask = zynq_gpio_irq_mask,
604 .irq_unmask = zynq_gpio_irq_unmask,
605 .irq_set_type = zynq_gpio_set_irq_type,
606 .irq_set_wake = zynq_gpio_set_wake,
607 .irq_request_resources = zynq_gpio_irq_reqres,
608 .irq_release_resources = zynq_gpio_irq_relres,
609 .flags = IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED |
610 IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_IMMUTABLE,
611 };
612
613 static const struct irq_chip zynq_gpio_edge_irqchip = {
614 .name = DRIVER_NAME,
615 .irq_enable = zynq_gpio_irq_enable,
616 .irq_ack = zynq_gpio_irq_ack,
617 .irq_mask = zynq_gpio_irq_mask,
618 .irq_unmask = zynq_gpio_irq_unmask,
619 .irq_set_type = zynq_gpio_set_irq_type,
620 .irq_set_wake = zynq_gpio_set_wake,
621 .irq_request_resources = zynq_gpio_irq_reqres,
622 .irq_release_resources = zynq_gpio_irq_relres,
623 .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_IMMUTABLE,
624 };
625
zynq_gpio_handle_bank_irq(struct zynq_gpio * gpio,unsigned int bank_num,unsigned long pending)626 static void zynq_gpio_handle_bank_irq(struct zynq_gpio *gpio,
627 unsigned int bank_num,
628 unsigned long pending)
629 {
630 unsigned int bank_offset = gpio->p_data->bank_min[bank_num];
631 struct irq_domain *irqdomain = gpio->chip.irq.domain;
632 int offset;
633
634 if (!pending)
635 return;
636
637 for_each_set_bit(offset, &pending, 32)
638 generic_handle_domain_irq(irqdomain, offset + bank_offset);
639 }
640
641 /**
642 * zynq_gpio_irqhandler - IRQ handler for the gpio banks of a gpio device
643 * @desc: irq descriptor instance of the 'irq'
644 *
645 * This function reads the Interrupt Status Register of each bank to get the
646 * gpio pin number which has triggered an interrupt. It then acks the triggered
647 * interrupt and calls the pin specific handler set by the higher layer
648 * application for that pin.
649 * Note: A bug is reported if no handler is set for the gpio pin.
650 */
zynq_gpio_irqhandler(struct irq_desc * desc)651 static void zynq_gpio_irqhandler(struct irq_desc *desc)
652 {
653 u32 int_sts, int_enb;
654 unsigned int bank_num;
655 struct zynq_gpio *gpio =
656 gpiochip_get_data(irq_desc_get_handler_data(desc));
657 struct irq_chip *irqchip = irq_desc_get_chip(desc);
658
659 chained_irq_enter(irqchip, desc);
660
661 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) {
662 int_sts = readl_relaxed(gpio->base_addr +
663 ZYNQ_GPIO_INTSTS_OFFSET(bank_num));
664 int_enb = readl_relaxed(gpio->base_addr +
665 ZYNQ_GPIO_INTMASK_OFFSET(bank_num));
666 zynq_gpio_handle_bank_irq(gpio, bank_num, int_sts & ~int_enb);
667 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL)
668 bank_num = bank_num + VERSAL_UNUSED_BANKS;
669 }
670
671 chained_irq_exit(irqchip, desc);
672 }
673
zynq_gpio_save_context(struct zynq_gpio * gpio)674 static void zynq_gpio_save_context(struct zynq_gpio *gpio)
675 {
676 unsigned int bank_num;
677
678 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) {
679 gpio->context.datalsw[bank_num] =
680 readl_relaxed(gpio->base_addr +
681 ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num));
682 gpio->context.datamsw[bank_num] =
683 readl_relaxed(gpio->base_addr +
684 ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num));
685 gpio->context.dirm[bank_num] = readl_relaxed(gpio->base_addr +
686 ZYNQ_GPIO_DIRM_OFFSET(bank_num));
687 gpio->context.int_en[bank_num] = readl_relaxed(gpio->base_addr +
688 ZYNQ_GPIO_INTMASK_OFFSET(bank_num));
689 gpio->context.int_type[bank_num] =
690 readl_relaxed(gpio->base_addr +
691 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num));
692 gpio->context.int_polarity[bank_num] =
693 readl_relaxed(gpio->base_addr +
694 ZYNQ_GPIO_INTPOL_OFFSET(bank_num));
695 gpio->context.int_any[bank_num] =
696 readl_relaxed(gpio->base_addr +
697 ZYNQ_GPIO_INTANY_OFFSET(bank_num));
698 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL)
699 bank_num = bank_num + VERSAL_UNUSED_BANKS;
700 }
701 }
702
zynq_gpio_restore_context(struct zynq_gpio * gpio)703 static void zynq_gpio_restore_context(struct zynq_gpio *gpio)
704 {
705 unsigned int bank_num;
706
707 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) {
708 writel_relaxed(ZYNQ_GPIO_IXR_DISABLE_ALL, gpio->base_addr +
709 ZYNQ_GPIO_INTDIS_OFFSET(bank_num));
710 writel_relaxed(gpio->context.datalsw[bank_num],
711 gpio->base_addr +
712 ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num));
713 writel_relaxed(gpio->context.datamsw[bank_num],
714 gpio->base_addr +
715 ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num));
716 writel_relaxed(gpio->context.dirm[bank_num],
717 gpio->base_addr +
718 ZYNQ_GPIO_DIRM_OFFSET(bank_num));
719 writel_relaxed(gpio->context.int_type[bank_num],
720 gpio->base_addr +
721 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num));
722 writel_relaxed(gpio->context.int_polarity[bank_num],
723 gpio->base_addr +
724 ZYNQ_GPIO_INTPOL_OFFSET(bank_num));
725 writel_relaxed(gpio->context.int_any[bank_num],
726 gpio->base_addr +
727 ZYNQ_GPIO_INTANY_OFFSET(bank_num));
728 writel_relaxed(~(gpio->context.int_en[bank_num]),
729 gpio->base_addr +
730 ZYNQ_GPIO_INTEN_OFFSET(bank_num));
731 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL)
732 bank_num = bank_num + VERSAL_UNUSED_BANKS;
733 }
734 }
735
zynq_gpio_suspend(struct device * dev)736 static int __maybe_unused zynq_gpio_suspend(struct device *dev)
737 {
738 struct zynq_gpio *gpio = dev_get_drvdata(dev);
739 struct irq_data *data = irq_get_irq_data(gpio->irq);
740
741 if (!data) {
742 dev_err(dev, "irq_get_irq_data() failed\n");
743 return -EINVAL;
744 }
745
746 if (!device_may_wakeup(dev))
747 disable_irq(gpio->irq);
748
749 if (!irqd_is_wakeup_set(data)) {
750 zynq_gpio_save_context(gpio);
751 return pm_runtime_force_suspend(dev);
752 }
753
754 return 0;
755 }
756
zynq_gpio_resume(struct device * dev)757 static int __maybe_unused zynq_gpio_resume(struct device *dev)
758 {
759 struct zynq_gpio *gpio = dev_get_drvdata(dev);
760 struct irq_data *data = irq_get_irq_data(gpio->irq);
761 int ret;
762
763 if (!data) {
764 dev_err(dev, "irq_get_irq_data() failed\n");
765 return -EINVAL;
766 }
767
768 if (!device_may_wakeup(dev))
769 enable_irq(gpio->irq);
770
771 if (!irqd_is_wakeup_set(data)) {
772 ret = pm_runtime_force_resume(dev);
773 zynq_gpio_restore_context(gpio);
774 return ret;
775 }
776
777 return 0;
778 }
779
zynq_gpio_runtime_suspend(struct device * dev)780 static int __maybe_unused zynq_gpio_runtime_suspend(struct device *dev)
781 {
782 struct zynq_gpio *gpio = dev_get_drvdata(dev);
783
784 clk_disable_unprepare(gpio->clk);
785
786 return 0;
787 }
788
zynq_gpio_runtime_resume(struct device * dev)789 static int __maybe_unused zynq_gpio_runtime_resume(struct device *dev)
790 {
791 struct zynq_gpio *gpio = dev_get_drvdata(dev);
792
793 return clk_prepare_enable(gpio->clk);
794 }
795
zynq_gpio_request(struct gpio_chip * chip,unsigned int offset)796 static int zynq_gpio_request(struct gpio_chip *chip, unsigned int offset)
797 {
798 int ret;
799
800 ret = pm_runtime_get_sync(chip->parent);
801
802 /*
803 * If the device is already active pm_runtime_get() will return 1 on
804 * success, but gpio_request still needs to return 0.
805 */
806 return ret < 0 ? ret : 0;
807 }
808
zynq_gpio_free(struct gpio_chip * chip,unsigned int offset)809 static void zynq_gpio_free(struct gpio_chip *chip, unsigned int offset)
810 {
811 pm_runtime_put(chip->parent);
812 }
813
814 static const struct dev_pm_ops zynq_gpio_dev_pm_ops = {
815 SET_SYSTEM_SLEEP_PM_OPS(zynq_gpio_suspend, zynq_gpio_resume)
816 SET_RUNTIME_PM_OPS(zynq_gpio_runtime_suspend,
817 zynq_gpio_runtime_resume, NULL)
818 };
819
820 static const struct zynq_platform_data versal_gpio_def = {
821 .label = "versal_gpio",
822 .quirks = GPIO_QUIRK_VERSAL,
823 .ngpio = 58,
824 .max_bank = VERSAL_GPIO_MAX_BANK,
825 .bank_min[0] = 0,
826 .bank_max[0] = 25, /* 0 to 25 are connected to MIOs (26 pins) */
827 .bank_min[3] = 26,
828 .bank_max[3] = 57, /* Bank 3 is connected to FMIOs (32 pins) */
829 };
830
831 static const struct zynq_platform_data pmc_gpio_def = {
832 .label = "pmc_gpio",
833 .ngpio = 116,
834 .max_bank = PMC_GPIO_MAX_BANK,
835 .bank_min[0] = 0,
836 .bank_max[0] = 25, /* 0 to 25 are connected to MIOs (26 pins) */
837 .bank_min[1] = 26,
838 .bank_max[1] = 51, /* Bank 1 are connected to MIOs (26 pins) */
839 .bank_min[3] = 52,
840 .bank_max[3] = 83, /* Bank 3 is connected to EMIOs (32 pins) */
841 .bank_min[4] = 84,
842 .bank_max[4] = 115, /* Bank 4 is connected to EMIOs (32 pins) */
843 };
844
845 static const struct zynq_platform_data zynqmp_gpio_def = {
846 .label = "zynqmp_gpio",
847 .quirks = GPIO_QUIRK_DATA_RO_BUG,
848 .ngpio = ZYNQMP_GPIO_NR_GPIOS,
849 .max_bank = ZYNQMP_GPIO_MAX_BANK,
850 .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(MP),
851 .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(MP),
852 .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(MP),
853 .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(MP),
854 .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(MP),
855 .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(MP),
856 .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(MP),
857 .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(MP),
858 .bank_min[4] = ZYNQ_GPIO_BANK4_PIN_MIN(MP),
859 .bank_max[4] = ZYNQ_GPIO_BANK4_PIN_MAX(MP),
860 .bank_min[5] = ZYNQ_GPIO_BANK5_PIN_MIN(MP),
861 .bank_max[5] = ZYNQ_GPIO_BANK5_PIN_MAX(MP),
862 };
863
864 static const struct zynq_platform_data zynq_gpio_def = {
865 .label = "zynq_gpio",
866 .quirks = ZYNQ_GPIO_QUIRK_IS_ZYNQ | GPIO_QUIRK_DATA_RO_BUG,
867 .ngpio = ZYNQ_GPIO_NR_GPIOS,
868 .max_bank = ZYNQ_GPIO_MAX_BANK,
869 .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(),
870 .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(),
871 .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(),
872 .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(),
873 .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(),
874 .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(),
875 .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(),
876 .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(),
877 };
878
879 static const struct of_device_id zynq_gpio_of_match[] = {
880 { .compatible = "xlnx,zynq-gpio-1.0", .data = &zynq_gpio_def },
881 { .compatible = "xlnx,zynqmp-gpio-1.0", .data = &zynqmp_gpio_def },
882 { .compatible = "xlnx,versal-gpio-1.0", .data = &versal_gpio_def },
883 { .compatible = "xlnx,pmc-gpio-1.0", .data = &pmc_gpio_def },
884 { /* end of table */ }
885 };
886 MODULE_DEVICE_TABLE(of, zynq_gpio_of_match);
887
888 /**
889 * zynq_gpio_probe - Initialization method for a zynq_gpio device
890 * @pdev: platform device instance
891 *
892 * This function allocates memory resources for the gpio device and registers
893 * all the banks of the device. It will also set up interrupts for the gpio
894 * pins.
895 * Note: Interrupts are disabled for all the banks during initialization.
896 *
897 * Return: 0 on success, negative error otherwise.
898 */
zynq_gpio_probe(struct platform_device * pdev)899 static int zynq_gpio_probe(struct platform_device *pdev)
900 {
901 int ret, bank_num;
902 struct zynq_gpio *gpio;
903 struct gpio_chip *chip;
904 struct gpio_irq_chip *girq;
905 const struct of_device_id *match;
906
907 gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
908 if (!gpio)
909 return -ENOMEM;
910
911 match = of_match_node(zynq_gpio_of_match, pdev->dev.of_node);
912 if (!match) {
913 dev_err(&pdev->dev, "of_match_node() failed\n");
914 return -EINVAL;
915 }
916 gpio->p_data = match->data;
917 platform_set_drvdata(pdev, gpio);
918
919 gpio->base_addr = devm_platform_ioremap_resource(pdev, 0);
920 if (IS_ERR(gpio->base_addr))
921 return PTR_ERR(gpio->base_addr);
922
923 gpio->irq = platform_get_irq(pdev, 0);
924 if (gpio->irq < 0)
925 return gpio->irq;
926
927 /* configure the gpio chip */
928 chip = &gpio->chip;
929 chip->label = gpio->p_data->label;
930 chip->owner = THIS_MODULE;
931 chip->parent = &pdev->dev;
932 chip->get = zynq_gpio_get_value;
933 chip->set = zynq_gpio_set_value;
934 chip->request = zynq_gpio_request;
935 chip->free = zynq_gpio_free;
936 chip->direction_input = zynq_gpio_dir_in;
937 chip->direction_output = zynq_gpio_dir_out;
938 chip->get_direction = zynq_gpio_get_direction;
939 chip->base = of_alias_get_id(pdev->dev.of_node, "gpio");
940 chip->ngpio = gpio->p_data->ngpio;
941
942 /* Retrieve GPIO clock */
943 gpio->clk = devm_clk_get_enabled(&pdev->dev, NULL);
944 if (IS_ERR(gpio->clk))
945 return dev_err_probe(&pdev->dev, PTR_ERR(gpio->clk), "input clock not found.\n");
946
947 spin_lock_init(&gpio->dirlock);
948
949 pm_runtime_set_active(&pdev->dev);
950 pm_runtime_enable(&pdev->dev);
951 ret = pm_runtime_resume_and_get(&pdev->dev);
952 if (ret < 0)
953 goto err_pm_dis;
954
955 /* disable interrupts for all banks */
956 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) {
957 writel_relaxed(ZYNQ_GPIO_IXR_DISABLE_ALL, gpio->base_addr +
958 ZYNQ_GPIO_INTDIS_OFFSET(bank_num));
959 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL)
960 bank_num = bank_num + VERSAL_UNUSED_BANKS;
961 }
962
963 /* Set up the GPIO irqchip */
964 girq = &chip->irq;
965 gpio_irq_chip_set_chip(girq, &zynq_gpio_edge_irqchip);
966 girq->parent_handler = zynq_gpio_irqhandler;
967 girq->num_parents = 1;
968 girq->parents = devm_kcalloc(&pdev->dev, 1,
969 sizeof(*girq->parents),
970 GFP_KERNEL);
971 if (!girq->parents) {
972 ret = -ENOMEM;
973 goto err_pm_put;
974 }
975 girq->parents[0] = gpio->irq;
976 girq->default_type = IRQ_TYPE_NONE;
977 girq->handler = handle_level_irq;
978
979 /* report a bug if gpio chip registration fails */
980 ret = gpiochip_add_data(chip, gpio);
981 if (ret) {
982 dev_err(&pdev->dev, "Failed to add gpio chip\n");
983 goto err_pm_put;
984 }
985
986 irq_set_status_flags(gpio->irq, IRQ_DISABLE_UNLAZY);
987 device_init_wakeup(&pdev->dev, 1);
988 pm_runtime_put(&pdev->dev);
989
990 return 0;
991
992 err_pm_put:
993 pm_runtime_put(&pdev->dev);
994 err_pm_dis:
995 pm_runtime_disable(&pdev->dev);
996
997 return ret;
998 }
999
1000 /**
1001 * zynq_gpio_remove - Driver removal function
1002 * @pdev: platform device instance
1003 *
1004 * Return: 0 always
1005 */
zynq_gpio_remove(struct platform_device * pdev)1006 static void zynq_gpio_remove(struct platform_device *pdev)
1007 {
1008 struct zynq_gpio *gpio = platform_get_drvdata(pdev);
1009 int ret;
1010
1011 ret = pm_runtime_get_sync(&pdev->dev);
1012 if (ret < 0)
1013 dev_warn(&pdev->dev, "pm_runtime_get_sync() Failed\n");
1014 gpiochip_remove(&gpio->chip);
1015 device_set_wakeup_capable(&pdev->dev, 0);
1016 pm_runtime_disable(&pdev->dev);
1017 }
1018
1019 static struct platform_driver zynq_gpio_driver = {
1020 .driver = {
1021 .name = DRIVER_NAME,
1022 .pm = &zynq_gpio_dev_pm_ops,
1023 .of_match_table = zynq_gpio_of_match,
1024 },
1025 .probe = zynq_gpio_probe,
1026 .remove = zynq_gpio_remove,
1027 };
1028
1029 module_platform_driver(zynq_gpio_driver);
1030
1031 MODULE_AUTHOR("Xilinx Inc.");
1032 MODULE_DESCRIPTION("Zynq GPIO driver");
1033 MODULE_LICENSE("GPL");
1034