xref: /linux/drivers/usb/gadget/udc/omap_udc.h (revision 498495dba268b20e8eadd7fe93c140c68b6cc9d2)
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /*
3  * omap_udc.h -- for omap 3.2 udc, with OTG support
4  *
5  * 2004 (C) Texas Instruments, Inc.
6  * 2004 (C) David Brownell
7  */
8 
9 /*
10  * USB device/endpoint management registers
11  */
12 
13 #define	UDC_REV				(UDC_BASE + 0x0)	/* Revision */
14 #define	UDC_EP_NUM			(UDC_BASE + 0x4)	/* Which endpoint */
15 #	define	UDC_SETUP_SEL		(1 << 6)
16 #	define	UDC_EP_SEL		(1 << 5)
17 #	define	UDC_EP_DIR		(1 << 4)
18 	/* low 4 bits for endpoint number */
19 #define	UDC_DATA			(UDC_BASE + 0x08)	/* Endpoint FIFO */
20 #define	UDC_CTRL			(UDC_BASE + 0x0C)	/* Endpoint control */
21 #	define	UDC_CLR_HALT		(1 << 7)
22 #	define	UDC_SET_HALT		(1 << 6)
23 #	define	UDC_CLRDATA_TOGGLE	(1 << 3)
24 #	define	UDC_SET_FIFO_EN		(1 << 2)
25 #	define	UDC_CLR_EP		(1 << 1)
26 #	define	UDC_RESET_EP		(1 << 0)
27 #define	UDC_STAT_FLG			(UDC_BASE + 0x10)	/* Endpoint status */
28 #	define	UDC_NO_RXPACKET		(1 << 15)
29 #	define	UDC_MISS_IN		(1 << 14)
30 #	define	UDC_DATA_FLUSH		(1 << 13)
31 #	define	UDC_ISO_ERR		(1 << 12)
32 #	define	UDC_ISO_FIFO_EMPTY	(1 << 9)
33 #	define	UDC_ISO_FIFO_FULL	(1 << 8)
34 #	define	UDC_EP_HALTED		(1 << 6)
35 #	define	UDC_STALL		(1 << 5)
36 #	define	UDC_NAK			(1 << 4)
37 #	define	UDC_ACK			(1 << 3)
38 #	define	UDC_FIFO_EN		(1 << 2)
39 #	define	UDC_NON_ISO_FIFO_EMPTY	(1 << 1)
40 #	define	UDC_NON_ISO_FIFO_FULL	(1 << 0)
41 #define	UDC_RXFSTAT			(UDC_BASE + 0x14)	/* OUT bytecount */
42 #define	UDC_SYSCON1			(UDC_BASE + 0x18)	/* System config 1 */
43 #	define	UDC_CFG_LOCK		(1 << 8)
44 #	define	UDC_DATA_ENDIAN		(1 << 7)
45 #	define	UDC_DMA_ENDIAN		(1 << 6)
46 #	define	UDC_NAK_EN		(1 << 4)
47 #	define	UDC_AUTODECODE_DIS	(1 << 3)
48 #	define	UDC_SELF_PWR		(1 << 2)
49 #	define	UDC_SOFF_DIS		(1 << 1)
50 #	define	UDC_PULLUP_EN		(1 << 0)
51 #define	UDC_SYSCON2			(UDC_BASE + 0x1C)	/* System config 2 */
52 #	define	UDC_RMT_WKP		(1 << 6)
53 #	define	UDC_STALL_CMD		(1 << 5)
54 #	define	UDC_DEV_CFG		(1 << 3)
55 #	define	UDC_CLR_CFG		(1 << 2)
56 #define	UDC_DEVSTAT			(UDC_BASE + 0x20)	/* Device status */
57 #	define	UDC_B_HNP_ENABLE	(1 << 9)
58 #	define	UDC_A_HNP_SUPPORT	(1 << 8)
59 #	define	UDC_A_ALT_HNP_SUPPORT	(1 << 7)
60 #	define	UDC_R_WK_OK		(1 << 6)
61 #	define	UDC_USB_RESET		(1 << 5)
62 #	define	UDC_SUS			(1 << 4)
63 #	define	UDC_CFG			(1 << 3)
64 #	define	UDC_ADD			(1 << 2)
65 #	define	UDC_DEF			(1 << 1)
66 #	define	UDC_ATT			(1 << 0)
67 #define	UDC_SOF				(UDC_BASE + 0x24)	/* Start of frame */
68 #	define	UDC_FT_LOCK		(1 << 12)
69 #	define	UDC_TS_OK		(1 << 11)
70 #	define	UDC_TS			0x03ff
71 #define	UDC_IRQ_EN			(UDC_BASE + 0x28)	/* Interrupt enable */
72 #	define	UDC_SOF_IE		(1 << 7)
73 #	define	UDC_EPN_RX_IE		(1 << 5)
74 #	define	UDC_EPN_TX_IE		(1 << 4)
75 #	define	UDC_DS_CHG_IE		(1 << 3)
76 #	define	UDC_EP0_IE		(1 << 0)
77 #define	UDC_DMA_IRQ_EN			(UDC_BASE + 0x2C)	/* DMA irq enable */
78 	/* rx/tx dma channels numbered 1-3 not 0-2 */
79 #	define	UDC_TX_DONE_IE(n)	(1 << (4 * (n) - 2))
80 #	define	UDC_RX_CNT_IE(n)	(1 << (4 * (n) - 3))
81 #	define	UDC_RX_EOT_IE(n)	(1 << (4 * (n) - 4))
82 #define	UDC_IRQ_SRC			(UDC_BASE + 0x30)	/* Interrupt source */
83 #	define	UDC_TXN_DONE		(1 << 10)
84 #	define	UDC_RXN_CNT		(1 << 9)
85 #	define	UDC_RXN_EOT		(1 << 8)
86 #	define	UDC_IRQ_SOF		(1 << 7)
87 #	define	UDC_EPN_RX		(1 << 5)
88 #	define	UDC_EPN_TX		(1 << 4)
89 #	define	UDC_DS_CHG		(1 << 3)
90 #	define	UDC_SETUP		(1 << 2)
91 #	define	UDC_EP0_RX		(1 << 1)
92 #	define	UDC_EP0_TX		(1 << 0)
93 #	define	UDC_IRQ_SRC_MASK	0x7bf
94 #define	UDC_EPN_STAT			(UDC_BASE + 0x34)	/* EP irq status */
95 #define	UDC_DMAN_STAT			(UDC_BASE + 0x38)	/* DMA irq status */
96 #	define	UDC_DMA_RX_SB		(1 << 12)
97 #	define	UDC_DMA_RX_SRC(x)	(((x)>>8) & 0xf)
98 #	define	UDC_DMA_TX_SRC(x)	(((x)>>0) & 0xf)
99 
100 
101 /* DMA configuration registers:  up to three channels in each direction.  */
102 #define	UDC_RXDMA_CFG			(UDC_BASE + 0x40)	/* 3 eps for RX DMA */
103 #	define	UDC_DMA_REQ		(1 << 12)
104 #define	UDC_TXDMA_CFG			(UDC_BASE + 0x44)	/* 3 eps for TX DMA */
105 #define	UDC_DATA_DMA			(UDC_BASE + 0x48)	/* rx/tx fifo addr */
106 
107 /* rx/tx dma control, numbering channels 1-3 not 0-2 */
108 #define	UDC_TXDMA(chan)			(UDC_BASE + 0x50 - 4 + 4 * (chan))
109 #	define UDC_TXN_EOT		(1 << 15)	/* bytes vs packets */
110 #	define UDC_TXN_START		(1 << 14)	/* start transfer */
111 #	define UDC_TXN_TSC		0x03ff		/* units in xfer */
112 #define	UDC_RXDMA(chan)			(UDC_BASE + 0x60 - 4 + 4 * (chan))
113 #	define UDC_RXN_STOP		(1 << 15)	/* enable EOT irq */
114 #	define UDC_RXN_TC		0x00ff		/* packets in xfer */
115 
116 
117 /*
118  * Endpoint configuration registers (used before CFG_LOCK is set)
119  * UDC_EP_TX(0) is unused
120  */
121 #define	UDC_EP_RX(endpoint)		(UDC_BASE + 0x80 + (endpoint)*4)
122 #	define	UDC_EPN_RX_VALID	(1 << 15)
123 #	define	UDC_EPN_RX_DB		(1 << 14)
124 	/* buffer size in bits 13, 12 */
125 #	define	UDC_EPN_RX_ISO		(1 << 11)
126 	/* buffer pointer in low 11 bits */
127 #define	UDC_EP_TX(endpoint)		(UDC_BASE + 0xc0 + (endpoint)*4)
128 	/* same bitfields as in RX */
129 
130 /*-------------------------------------------------------------------------*/
131 
132 struct omap_req {
133 	struct usb_request		req;
134 	struct list_head		queue;
135 	unsigned			dma_bytes;
136 	unsigned			mapped:1;
137 };
138 
139 struct omap_ep {
140 	struct usb_ep			ep;
141 	struct list_head		queue;
142 	unsigned long			irqs;
143 	struct list_head		iso;
144 	char				name[14];
145 	u16				maxpacket;
146 	u8				bEndpointAddress;
147 	u8				bmAttributes;
148 	unsigned			double_buf:1;
149 	unsigned			stopped:1;
150 	unsigned			fnf:1;
151 	unsigned			has_dma:1;
152 	u8				ackwait;
153 	u8				dma_channel;
154 	u16				dma_counter;
155 	int				lch;
156 	struct omap_udc			*udc;
157 	struct timer_list		timer;
158 };
159 
160 struct omap_udc {
161 	struct usb_gadget		gadget;
162 	struct usb_gadget_driver	*driver;
163 	spinlock_t			lock;
164 	struct omap_ep			ep[32];
165 	u16				devstat;
166 	u16				clr_halt;
167 	struct usb_phy			*transceiver;
168 	struct list_head		iso;
169 	unsigned			softconnect:1;
170 	unsigned			vbus_active:1;
171 	unsigned			ep0_pending:1;
172 	unsigned			ep0_in:1;
173 	unsigned			ep0_set_config:1;
174 	unsigned			ep0_reset_config:1;
175 	unsigned			ep0_setup:1;
176 	struct completion		*done;
177 	struct clk			*dc_clk;
178 	struct clk			*hhc_clk;
179 	unsigned			clk_requested:1;
180 };
181 
182 /*-------------------------------------------------------------------------*/
183 
184 #ifdef VERBOSE
185 #    define VDBG		DBG
186 #else
187 #    define VDBG(stuff...)	do{}while(0)
188 #endif
189 
190 #define ERR(stuff...)		pr_err("udc: " stuff)
191 #define WARNING(stuff...)	pr_warn("udc: " stuff)
192 #define INFO(stuff...)		pr_info("udc: " stuff)
193 #define DBG(stuff...)		pr_debug("udc: " stuff)
194 
195 /*-------------------------------------------------------------------------*/
196 
197 /* MOD_CONF_CTRL_0 */
198 #define VBUS_W2FC_1510		(1 << 17)	/* 0 gpio0, 1 dvdd2 pin */
199 
200 /* FUNC_MUX_CTRL_0 */
201 #define	VBUS_CTRL_1510		(1 << 19)	/* 1 connected (software) */
202 #define	VBUS_MODE_1510		(1 << 18)	/* 0 hardware, 1 software */
203 
204 #define	HMC_1510	((omap_readl(MOD_CONF_CTRL_0) >> 1) & 0x3f)
205 #define	HMC_1610	(omap_readl(OTG_SYSCON_2) & 0x3f)
206 #define	HMC		(cpu_is_omap15xx() ? HMC_1510 : HMC_1610)
207 
208