xref: /linux/drivers/scsi/sym53c8xx_2/sym_defs.h (revision 75bf465f0bc33e9b776a46d6a1b9b990f5fb7c37)
1 /* SPDX-License-Identifier: GPL-2.0-or-later */
2 /*
3  * Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family
4  * of PCI-SCSI IO processors.
5  *
6  * Copyright (C) 1999-2001  Gerard Roudier <groudier@free.fr>
7  *
8  * This driver is derived from the Linux sym53c8xx driver.
9  * Copyright (C) 1998-2000  Gerard Roudier
10  *
11  * The sym53c8xx driver is derived from the ncr53c8xx driver that had been
12  * a port of the FreeBSD ncr driver to Linux-1.2.13.
13  *
14  * The original ncr driver has been written for 386bsd and FreeBSD by
15  *         Wolfgang Stanglmeier        <wolf@cologne.de>
16  *         Stefan Esser                <se@mi.Uni-Koeln.de>
17  * Copyright (C) 1994  Wolfgang Stanglmeier
18  *
19  * Other major contributions:
20  *
21  * NVRAM detection and reading.
22  * Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
23  *
24  *-----------------------------------------------------------------------------
25  */
26 
27 #ifndef SYM_DEFS_H
28 #define SYM_DEFS_H
29 
30 #define SYM_VERSION "2.2.3"
31 #define SYM_DRIVER_NAME	"sym-" SYM_VERSION
32 
33 /*
34  *	SYM53C8XX device features descriptor.
35  */
36 struct sym_chip {
37 	u_short	device_id;
38 	u_short	revision_id;
39 	char	*name;
40 	u_char	burst_max;	/* log-base-2 of max burst */
41 	u_char	offset_max;
42 	u_char	nr_divisor;
43 	u_char	lp_probe_bit;
44 	u_int	features;
45 #define FE_LED0		(1<<0)
46 #define FE_WIDE		(1<<1)    /* Wide data transfers */
47 #define FE_ULTRA	(1<<2)	  /* Ultra speed 20Mtrans/sec */
48 #define FE_ULTRA2	(1<<3)	  /* Ultra 2 - 40 Mtrans/sec */
49 #define FE_DBLR		(1<<4)	  /* Clock doubler present */
50 #define FE_QUAD		(1<<5)	  /* Clock quadrupler present */
51 #define FE_ERL		(1<<6)    /* Enable read line */
52 #define FE_CLSE		(1<<7)    /* Cache line size enable */
53 #define FE_WRIE		(1<<8)    /* Write & Invalidate enable */
54 #define FE_ERMP		(1<<9)    /* Enable read multiple */
55 #define FE_BOF		(1<<10)   /* Burst opcode fetch */
56 #define FE_DFS		(1<<11)   /* DMA fifo size */
57 #define FE_PFEN		(1<<12)   /* Prefetch enable */
58 #define FE_LDSTR	(1<<13)   /* Load/Store supported */
59 #define FE_RAM		(1<<14)   /* On chip RAM present */
60 #define FE_VARCLK	(1<<15)   /* Clock frequency may vary */
61 #define FE_RAM8K	(1<<16)   /* On chip RAM sized 8Kb */
62 #define FE_64BIT	(1<<17)   /* 64-bit PCI BUS interface */
63 #define FE_IO256	(1<<18)   /* Requires full 256 bytes in PCI space */
64 #define FE_NOPM		(1<<19)   /* Scripts handles phase mismatch */
65 #define FE_LEDC		(1<<20)   /* Hardware control of LED */
66 #define FE_ULTRA3	(1<<21)	  /* Ultra 3 - 80 Mtrans/sec DT */
67 #define FE_66MHZ	(1<<22)	  /* 66MHz PCI support */
68 #define FE_CRC		(1<<23)	  /* CRC support */
69 #define FE_DIFF		(1<<24)	  /* SCSI HVD support */
70 #define FE_DFBC		(1<<25)	  /* Have DFBC register */
71 #define FE_LCKFRQ	(1<<26)	  /* Have LCKFRQ */
72 #define FE_C10		(1<<27)	  /* Various C10 core (mis)features */
73 #define FE_U3EN		(1<<28)	  /* U3EN bit usable */
74 #define FE_DAC		(1<<29)	  /* Support PCI DAC (64 bit addressing) */
75 #define FE_ISTAT1 	(1<<30)   /* Have ISTAT1, MBOX0, MBOX1 registers */
76 
77 #define FE_CACHE_SET	(FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP)
78 #define FE_CACHE0_SET	(FE_CACHE_SET & ~FE_ERL)
79 };
80 
81 /*
82  *	SYM53C8XX IO register data structure.
83  */
84 struct sym_reg {
85 /*00*/  u8	nc_scntl0;	/* full arb., ena parity, par->ATN  */
86 
87 /*01*/  u8	nc_scntl1;	/* no reset                         */
88         #define   ISCON   0x10  /* connected to scsi		    */
89         #define   CRST    0x08  /* force reset                      */
90         #define   IARB    0x02  /* immediate arbitration            */
91 
92 /*02*/  u8	nc_scntl2;	/* no disconnect expected           */
93 	#define   SDU     0x80  /* cmd: disconnect will raise error */
94 	#define   CHM     0x40  /* sta: chained mode                */
95 	#define   WSS     0x08  /* sta: wide scsi send           [W]*/
96 	#define   WSR     0x01  /* sta: wide scsi received       [W]*/
97 
98 /*03*/  u8	nc_scntl3;	/* cnf system clock dependent       */
99 	#define   EWS     0x08  /* cmd: enable wide scsi         [W]*/
100 	#define   ULTRA   0x80  /* cmd: ULTRA enable                */
101 				/* bits 0-2, 7 rsvd for C1010       */
102 
103 /*04*/  u8	nc_scid;	/* cnf host adapter scsi address    */
104 	#define   RRE     0x40  /* r/w:e enable response to resel.  */
105 	#define   SRE     0x20  /* r/w:e enable response to select  */
106 
107 /*05*/  u8	nc_sxfer;	/* ### Sync speed and count         */
108 				/* bits 6-7 rsvd for C1010          */
109 
110 /*06*/  u8	nc_sdid;	/* ### Destination-ID               */
111 
112 /*07*/  u8	nc_gpreg;	/* ??? IO-Pins                      */
113 
114 /*08*/  u8	nc_sfbr;	/* ### First byte received          */
115 
116 /*09*/  u8	nc_socl;
117 	#define   CREQ	  0x80	/* r/w: SCSI-REQ                    */
118 	#define   CACK	  0x40	/* r/w: SCSI-ACK                    */
119 	#define   CBSY	  0x20	/* r/w: SCSI-BSY                    */
120 	#define   CSEL	  0x10	/* r/w: SCSI-SEL                    */
121 	#define   CATN	  0x08	/* r/w: SCSI-ATN                    */
122 	#define   CMSG	  0x04	/* r/w: SCSI-MSG                    */
123 	#define   CC_D	  0x02	/* r/w: SCSI-C_D                    */
124 	#define   CI_O	  0x01	/* r/w: SCSI-I_O                    */
125 
126 /*0a*/  u8	nc_ssid;
127 
128 /*0b*/  u8	nc_sbcl;
129 
130 /*0c*/  u8	nc_dstat;
131         #define   DFE     0x80  /* sta: dma fifo empty              */
132         #define   MDPE    0x40  /* int: master data parity error    */
133         #define   BF      0x20  /* int: script: bus fault           */
134         #define   ABRT    0x10  /* int: script: command aborted     */
135         #define   SSI     0x08  /* int: script: single step         */
136         #define   SIR     0x04  /* int: script: interrupt instruct. */
137         #define   IID     0x01  /* int: script: illegal instruct.   */
138 
139 /*0d*/  u8	nc_sstat0;
140         #define   ILF     0x80  /* sta: data in SIDL register lsb   */
141         #define   ORF     0x40  /* sta: data in SODR register lsb   */
142         #define   OLF     0x20  /* sta: data in SODL register lsb   */
143         #define   AIP     0x10  /* sta: arbitration in progress     */
144         #define   LOA     0x08  /* sta: arbitration lost            */
145         #define   WOA     0x04  /* sta: arbitration won             */
146         #define   IRST    0x02  /* sta: scsi reset signal           */
147         #define   SDP     0x01  /* sta: scsi parity signal          */
148 
149 /*0e*/  u8	nc_sstat1;
150 	#define   FF3210  0xf0	/* sta: bytes in the scsi fifo      */
151 
152 /*0f*/  u8	nc_sstat2;
153         #define   ILF1    0x80  /* sta: data in SIDL register msb[W]*/
154         #define   ORF1    0x40  /* sta: data in SODR register msb[W]*/
155         #define   OLF1    0x20  /* sta: data in SODL register msb[W]*/
156         #define   DM      0x04  /* sta: DIFFSENS mismatch (895/6 only) */
157         #define   LDSC    0x02  /* sta: disconnect & reconnect      */
158 
159 /*10*/  u8	nc_dsa;		/* --> Base page                    */
160 /*11*/  u8	nc_dsa1;
161 /*12*/  u8	nc_dsa2;
162 /*13*/  u8	nc_dsa3;
163 
164 /*14*/  u8	nc_istat;	/* --> Main Command and status      */
165         #define   CABRT   0x80  /* cmd: abort current operation     */
166         #define   SRST    0x40  /* mod: reset chip                  */
167         #define   SIGP    0x20  /* r/w: message from host to script */
168         #define   SEM     0x10  /* r/w: message between host + script  */
169         #define   CON     0x08  /* sta: connected to scsi           */
170         #define   INTF    0x04  /* sta: int on the fly (reset by wr)*/
171         #define   SIP     0x02  /* sta: scsi-interrupt              */
172         #define   DIP     0x01  /* sta: host/script interrupt       */
173 
174 /*15*/  u8	nc_istat1;	/* 896 only */
175         #define   FLSH    0x04  /* sta: chip is flushing            */
176         #define   SCRUN   0x02  /* sta: scripts are running         */
177         #define   SIRQD   0x01  /* r/w: disable INT pin             */
178 
179 /*16*/  u8	nc_mbox0;	/* 896 only */
180 /*17*/  u8	nc_mbox1;	/* 896 only */
181 
182 /*18*/	u8	nc_ctest0;
183 /*19*/  u8	nc_ctest1;
184 
185 /*1a*/  u8	nc_ctest2;
186 	#define   CSIGP   0x40
187 				/* bits 0-2,7 rsvd for C1010        */
188 
189 /*1b*/  u8	nc_ctest3;
190 	#define   FLF     0x08  /* cmd: flush dma fifo              */
191 	#define   CLF	  0x04	/* cmd: clear dma fifo		    */
192 	#define   FM      0x02  /* mod: fetch pin mode              */
193 	#define   WRIE    0x01  /* mod: write and invalidate enable */
194 				/* bits 4-7 rsvd for C1010          */
195 
196 /*1c*/  u32	nc_temp;	/* ### Temporary stack              */
197 
198 /*20*/	u8	nc_dfifo;
199 /*21*/  u8	nc_ctest4;
200 	#define   BDIS    0x80  /* mod: burst disable               */
201 	#define   MPEE    0x08  /* mod: master parity error enable  */
202 
203 /*22*/  u8	nc_ctest5;
204 	#define   DFS     0x20  /* mod: dma fifo size               */
205 				/* bits 0-1, 3-7 rsvd for C1010     */
206 
207 /*23*/  u8	nc_ctest6;
208 
209 /*24*/  u32	nc_dbc;		/* ### Byte count and command       */
210 /*28*/  u32	nc_dnad;	/* ### Next command register        */
211 /*2c*/  u32	nc_dsp;		/* --> Script Pointer               */
212 /*30*/  u32	nc_dsps;	/* --> Script pointer save/opcode#2 */
213 
214 /*34*/  u8	nc_scratcha;	/* Temporary register a            */
215 /*35*/  u8	nc_scratcha1;
216 /*36*/  u8	nc_scratcha2;
217 /*37*/  u8	nc_scratcha3;
218 
219 /*38*/  u8	nc_dmode;
220 	#define   BL_2    0x80  /* mod: burst length shift value +2 */
221 	#define   BL_1    0x40  /* mod: burst length shift value +1 */
222 	#define   ERL     0x08  /* mod: enable read line            */
223 	#define   ERMP    0x04  /* mod: enable read multiple        */
224 	#define   BOF     0x02  /* mod: burst op code fetch         */
225 
226 /*39*/  u8	nc_dien;
227 /*3a*/  u8	nc_sbr;
228 
229 /*3b*/  u8	nc_dcntl;	/* --> Script execution control     */
230 	#define   CLSE    0x80  /* mod: cache line size enable      */
231 	#define   PFF     0x40  /* cmd: pre-fetch flush             */
232 	#define   PFEN    0x20  /* mod: pre-fetch enable            */
233 	#define   SSM     0x10  /* mod: single step mode            */
234 	#define   IRQM    0x08  /* mod: irq mode (1 = totem pole !) */
235 	#define   STD     0x04  /* cmd: start dma mode              */
236 	#define   IRQD    0x02  /* mod: irq disable                 */
237  	#define	  NOCOM   0x01	/* cmd: protect sfbr while reselect */
238 				/* bits 0-1 rsvd for C1010          */
239 
240 /*3c*/  u32	nc_adder;
241 
242 /*40*/  u16	nc_sien;	/* -->: interrupt enable            */
243 /*42*/  u16	nc_sist;	/* <--: interrupt status            */
244         #define   SBMC    0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
245         #define   STO     0x0400/* sta: timeout (select)            */
246         #define   GEN     0x0200/* sta: timeout (general)           */
247         #define   HTH     0x0100/* sta: timeout (handshake)         */
248         #define   MA      0x80  /* sta: phase mismatch              */
249         #define   CMP     0x40  /* sta: arbitration complete        */
250         #define   SEL     0x20  /* sta: selected by another device  */
251         #define   RSL     0x10  /* sta: reselected by another device*/
252         #define   SGE     0x08  /* sta: gross error (over/underflow)*/
253         #define   UDC     0x04  /* sta: unexpected disconnect       */
254         #define   RST     0x02  /* sta: scsi bus reset detected     */
255         #define   PAR     0x01  /* sta: scsi parity error           */
256 
257 /*44*/  u8	nc_slpar;
258 /*45*/  u8	nc_swide;
259 /*46*/  u8	nc_macntl;
260 /*47*/  u8	nc_gpcntl;
261 /*48*/  u8	nc_stime0;	/* cmd: timeout for select&handshake*/
262 /*49*/  u8	nc_stime1;	/* cmd: timeout user defined        */
263 /*4a*/  u16	nc_respid;	/* sta: Reselect-IDs                */
264 
265 /*4c*/  u8	nc_stest0;
266 
267 /*4d*/  u8	nc_stest1;
268 	#define   SCLK    0x80	/* Use the PCI clock as SCSI clock	*/
269 	#define   DBLEN   0x08	/* clock doubler running		*/
270 	#define   DBLSEL  0x04	/* clock doubler selected		*/
271 
272 
273 /*4e*/  u8	nc_stest2;
274 	#define   ROF     0x40	/* reset scsi offset (after gross error!) */
275 	#define   EXT     0x02  /* extended filtering                     */
276 
277 /*4f*/  u8	nc_stest3;
278 	#define   TE     0x80	/* c: tolerAnt enable */
279 	#define   HSC    0x20	/* c: Halt SCSI Clock */
280 	#define   CSF    0x02	/* c: clear scsi fifo */
281 
282 /*50*/  u16	nc_sidl;	/* Lowlevel: latched from scsi data */
283 /*52*/  u8	nc_stest4;
284 	#define   SMODE  0xc0	/* SCSI bus mode      (895/6 only) */
285 	#define    SMODE_HVD 0x40	/* High Voltage Differential       */
286 	#define    SMODE_SE  0x80	/* Single Ended                    */
287 	#define    SMODE_LVD 0xc0	/* Low Voltage Differential        */
288 	#define   LCKFRQ 0x20	/* Frequency Lock (895/6 only)     */
289 				/* bits 0-5 rsvd for C1010         */
290 
291 /*53*/  u8	nc_53_;
292 /*54*/  u16	nc_sodl;	/* Lowlevel: data out to scsi data  */
293 /*56*/	u8	nc_ccntl0;	/* Chip Control 0 (896)             */
294 	#define   ENPMJ  0x80	/* Enable Phase Mismatch Jump       */
295 	#define   PMJCTL 0x40	/* Phase Mismatch Jump Control      */
296 	#define   ENNDJ  0x20	/* Enable Non Data PM Jump          */
297 	#define   DISFC  0x10	/* Disable Auto FIFO Clear          */
298 	#define   DILS   0x02	/* Disable Internal Load/Store      */
299 	#define   DPR    0x01	/* Disable Pipe Req                 */
300 
301 /*57*/	u8	nc_ccntl1;	/* Chip Control 1 (896)             */
302 	#define   ZMOD   0x80	/* High Impedance Mode              */
303 	#define   DDAC   0x08	/* Disable Dual Address Cycle       */
304 	#define   XTIMOD 0x04	/* 64-bit Table Ind. Indexing Mode  */
305 	#define   EXTIBMV 0x02	/* Enable 64-bit Table Ind. BMOV    */
306 	#define   EXDBMV 0x01	/* Enable 64-bit Direct BMOV        */
307 
308 /*58*/  u16	nc_sbdl;	/* Lowlevel: data from scsi data    */
309 /*5a*/  u16	nc_5a_;
310 
311 /*5c*/  u8	nc_scr0;	/* Working register B               */
312 /*5d*/  u8	nc_scr1;
313 /*5e*/  u8	nc_scr2;
314 /*5f*/  u8	nc_scr3;
315 
316 /*60*/  u8	nc_scrx[64];	/* Working register C-R             */
317 /*a0*/	u32	nc_mmrs;	/* Memory Move Read Selector        */
318 /*a4*/	u32	nc_mmws;	/* Memory Move Write Selector       */
319 /*a8*/	u32	nc_sfs;		/* Script Fetch Selector            */
320 /*ac*/	u32	nc_drs;		/* DSA Relative Selector            */
321 /*b0*/	u32	nc_sbms;	/* Static Block Move Selector       */
322 /*b4*/	u32	nc_dbms;	/* Dynamic Block Move Selector      */
323 /*b8*/	u32	nc_dnad64;	/* DMA Next Address 64              */
324 /*bc*/	u16	nc_scntl4;	/* C1010 only                       */
325 	#define   U3EN    0x80	/* Enable Ultra 3                   */
326 	#define   AIPCKEN 0x40  /* AIP checking enable              */
327 				/* Also enable AIP generation on C10-33*/
328 	#define   XCLKH_DT 0x08 /* Extra clock of data hold on DT edge */
329 	#define   XCLKH_ST 0x04 /* Extra clock of data hold on ST edge */
330 	#define   XCLKS_DT 0x02 /* Extra clock of data set  on DT edge */
331 	#define   XCLKS_ST 0x01 /* Extra clock of data set  on ST edge */
332 /*be*/	u8	nc_aipcntl0;	/* AIP Control 0 C1010 only         */
333 /*bf*/	u8	nc_aipcntl1;	/* AIP Control 1 C1010 only         */
334 	#define DISAIP  0x08	/* Disable AIP generation C10-66 only  */
335 /*c0*/	u32	nc_pmjad1;	/* Phase Mismatch Jump Address 1    */
336 /*c4*/	u32	nc_pmjad2;	/* Phase Mismatch Jump Address 2    */
337 /*c8*/	u8	nc_rbc;		/* Remaining Byte Count             */
338 /*c9*/	u8	nc_rbc1;
339 /*ca*/	u8	nc_rbc2;
340 /*cb*/	u8	nc_rbc3;
341 
342 /*cc*/	u8	nc_ua;		/* Updated Address                  */
343 /*cd*/	u8	nc_ua1;
344 /*ce*/	u8	nc_ua2;
345 /*cf*/	u8	nc_ua3;
346 /*d0*/	u32	nc_esa;		/* Entry Storage Address            */
347 /*d4*/	u8	nc_ia;		/* Instruction Address              */
348 /*d5*/	u8	nc_ia1;
349 /*d6*/	u8	nc_ia2;
350 /*d7*/	u8	nc_ia3;
351 /*d8*/	u32	nc_sbc;		/* SCSI Byte Count (3 bytes only)   */
352 /*dc*/	u32	nc_csbc;	/* Cumulative SCSI Byte Count       */
353                                 /* Following for C1010 only         */
354 /*e0*/	u16    nc_crcpad;	/* CRC Value                        */
355 /*e2*/	u8     nc_crccntl0;	/* CRC control register             */
356 	#define   SNDCRC  0x10	/* Send CRC Request                 */
357 /*e3*/	u8     nc_crccntl1;	/* CRC control register             */
358 /*e4*/	u32    nc_crcdata;	/* CRC data register                */
359 /*e8*/	u32    nc_e8_;
360 /*ec*/	u32    nc_ec_;
361 /*f0*/	u16    nc_dfbc;		/* DMA FIFO byte count              */
362 };
363 
364 /*-----------------------------------------------------------
365  *
366  *	Utility macros for the script.
367  *
368  *-----------------------------------------------------------
369  */
370 
371 #define REGJ(p,r) (offsetof(struct sym_reg, p ## r))
372 #define REG(r) REGJ (nc_, r)
373 
374 /*-----------------------------------------------------------
375  *
376  *	SCSI phases
377  *
378  *-----------------------------------------------------------
379  */
380 
381 #define	SCR_DATA_OUT	0x00000000
382 #define	SCR_DATA_IN	0x01000000
383 #define	SCR_COMMAND	0x02000000
384 #define	SCR_STATUS	0x03000000
385 #define	SCR_DT_DATA_OUT	0x04000000
386 #define	SCR_DT_DATA_IN	0x05000000
387 #define SCR_MSG_OUT	0x06000000
388 #define SCR_MSG_IN      0x07000000
389 /* DT phases are illegal for non Ultra3 mode */
390 #define SCR_ILG_OUT	0x04000000
391 #define SCR_ILG_IN	0x05000000
392 
393 /*-----------------------------------------------------------
394  *
395  *	Data transfer via SCSI.
396  *
397  *-----------------------------------------------------------
398  *
399  *	MOVE_ABS (LEN)
400  *	<<start address>>
401  *
402  *	MOVE_IND (LEN)
403  *	<<dnad_offset>>
404  *
405  *	MOVE_TBL
406  *	<<dnad_offset>>
407  *
408  *-----------------------------------------------------------
409  */
410 
411 #define OPC_MOVE          0x08000000
412 
413 #define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
414 /* #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) */
415 #define SCR_MOVE_TBL     (0x10000000 | OPC_MOVE)
416 
417 #define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
418 /* #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) */
419 #define SCR_CHMOV_TBL     (0x10000000)
420 
421 #ifdef SYM_CONF_TARGET_ROLE_SUPPORT
422 /* We steal the `indirect addressing' flag for target mode MOVE in scripts */
423 
424 #define OPC_TCHMOVE        0x08000000
425 
426 #define SCR_TCHMOVE_ABS(l) ((0x20000000 | OPC_TCHMOVE) | (l))
427 #define SCR_TCHMOVE_TBL     (0x30000000 | OPC_TCHMOVE)
428 
429 #define SCR_TMOV_ABS(l)    ((0x20000000) | (l))
430 #define SCR_TMOV_TBL        (0x30000000)
431 #endif
432 
433 struct sym_tblmove {
434         u32  size;
435         u32  addr;
436 };
437 
438 /*-----------------------------------------------------------
439  *
440  *	Selection
441  *
442  *-----------------------------------------------------------
443  *
444  *	SEL_ABS | SCR_ID (0..15)    [ | REL_JMP]
445  *	<<alternate_address>>
446  *
447  *	SEL_TBL | << dnad_offset>>  [ | REL_JMP]
448  *	<<alternate_address>>
449  *
450  *-----------------------------------------------------------
451  */
452 
453 #define	SCR_SEL_ABS	0x40000000
454 #define	SCR_SEL_ABS_ATN	0x41000000
455 #define	SCR_SEL_TBL	0x42000000
456 #define	SCR_SEL_TBL_ATN	0x43000000
457 
458 #ifdef SYM_CONF_TARGET_ROLE_SUPPORT
459 #define	SCR_RESEL_ABS     0x40000000
460 #define	SCR_RESEL_ABS_ATN 0x41000000
461 #define	SCR_RESEL_TBL     0x42000000
462 #define	SCR_RESEL_TBL_ATN 0x43000000
463 #endif
464 
465 struct sym_tblsel {
466         u_char  sel_scntl4;	/* C1010 only */
467         u_char  sel_sxfer;
468         u_char  sel_id;
469         u_char  sel_scntl3;
470 };
471 
472 #define SCR_JMP_REL     0x04000000
473 #define SCR_ID(id)	(((u32)(id)) << 16)
474 
475 /*-----------------------------------------------------------
476  *
477  *	Waiting for Disconnect or Reselect
478  *
479  *-----------------------------------------------------------
480  *
481  *	WAIT_DISC
482  *	dummy: <<alternate_address>>
483  *
484  *	WAIT_RESEL
485  *	<<alternate_address>>
486  *
487  *-----------------------------------------------------------
488  */
489 
490 #define	SCR_WAIT_DISC	0x48000000
491 #define SCR_WAIT_RESEL  0x50000000
492 
493 #ifdef SYM_CONF_TARGET_ROLE_SUPPORT
494 #define	SCR_DISCONNECT	0x48000000
495 #endif
496 
497 /*-----------------------------------------------------------
498  *
499  *	Bit Set / Reset
500  *
501  *-----------------------------------------------------------
502  *
503  *	SET (flags {|.. })
504  *
505  *	CLR (flags {|.. })
506  *
507  *-----------------------------------------------------------
508  */
509 
510 #define SCR_SET(f)     (0x58000000 | (f))
511 #define SCR_CLR(f)     (0x60000000 | (f))
512 
513 #define	SCR_CARRY	0x00000400
514 #define	SCR_TRG		0x00000200
515 #define	SCR_ACK		0x00000040
516 #define	SCR_ATN		0x00000008
517 
518 
519 /*-----------------------------------------------------------
520  *
521  *	Memory to memory move
522  *
523  *-----------------------------------------------------------
524  *
525  *	COPY (bytecount)
526  *	<< source_address >>
527  *	<< destination_address >>
528  *
529  *	SCR_COPY   sets the NO FLUSH option by default.
530  *	SCR_COPY_F does not set this option.
531  *
532  *	For chips which do not support this option,
533  *	sym_fw_bind_script() will remove this bit.
534  *
535  *-----------------------------------------------------------
536  */
537 
538 #define SCR_NO_FLUSH 0x01000000
539 
540 #define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n))
541 #define SCR_COPY_F(n) (0xc0000000 | (n))
542 
543 /*-----------------------------------------------------------
544  *
545  *	Register move and binary operations
546  *
547  *-----------------------------------------------------------
548  *
549  *	SFBR_REG (reg, op, data)        reg  = SFBR op data
550  *	<< 0 >>
551  *
552  *	REG_SFBR (reg, op, data)        SFBR = reg op data
553  *	<< 0 >>
554  *
555  *	REG_REG  (reg, op, data)        reg  = reg op data
556  *	<< 0 >>
557  *
558  *-----------------------------------------------------------
559  *
560  *	On 825A, 875, 895 and 896 chips the content
561  *	of SFBR register can be used as data (SCR_SFBR_DATA).
562  *	The 896 has additionnal IO registers starting at
563  *	offset 0x80. Bit 7 of register offset is stored in
564  *	bit 7 of the SCRIPTS instruction first DWORD.
565  *
566  *-----------------------------------------------------------
567  */
568 
569 #define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80))
570 
571 #define SCR_SFBR_REG(reg,op,data) \
572         (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
573 
574 #define SCR_REG_SFBR(reg,op,data) \
575         (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
576 
577 #define SCR_REG_REG(reg,op,data) \
578         (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
579 
580 
581 #define      SCR_LOAD   0x00000000
582 #define      SCR_SHL    0x01000000
583 #define      SCR_OR     0x02000000
584 #define      SCR_XOR    0x03000000
585 #define      SCR_AND    0x04000000
586 #define      SCR_SHR    0x05000000
587 #define      SCR_ADD    0x06000000
588 #define      SCR_ADDC   0x07000000
589 
590 #define      SCR_SFBR_DATA   (0x00800000>>8ul)	/* Use SFBR as data */
591 
592 /*-----------------------------------------------------------
593  *
594  *	FROM_REG (reg)		  SFBR = reg
595  *	<< 0 >>
596  *
597  *	TO_REG	 (reg)		  reg  = SFBR
598  *	<< 0 >>
599  *
600  *	LOAD_REG (reg, data)	  reg  = <data>
601  *	<< 0 >>
602  *
603  *	LOAD_SFBR(data) 	  SFBR = <data>
604  *	<< 0 >>
605  *
606  *-----------------------------------------------------------
607  */
608 
609 #define	SCR_FROM_REG(reg) \
610 	SCR_REG_SFBR(reg,SCR_OR,0)
611 
612 #define	SCR_TO_REG(reg) \
613 	SCR_SFBR_REG(reg,SCR_OR,0)
614 
615 #define	SCR_LOAD_REG(reg,data) \
616 	SCR_REG_REG(reg,SCR_LOAD,data)
617 
618 #define SCR_LOAD_SFBR(data) \
619         (SCR_REG_SFBR (gpreg, SCR_LOAD, data))
620 
621 /*-----------------------------------------------------------
622  *
623  *	LOAD  from memory   to register.
624  *	STORE from register to memory.
625  *
626  *	Only supported by 810A, 860, 825A, 875, 895 and 896.
627  *
628  *-----------------------------------------------------------
629  *
630  *	LOAD_ABS (LEN)
631  *	<<start address>>
632  *
633  *	LOAD_REL (LEN)        (DSA relative)
634  *	<<dsa_offset>>
635  *
636  *-----------------------------------------------------------
637  */
638 
639 #define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul)
640 #define SCR_NO_FLUSH2	0x02000000
641 #define SCR_DSA_REL2	0x10000000
642 
643 #define SCR_LOAD_R(reg, how, n) \
644         (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
645 
646 #define SCR_STORE_R(reg, how, n) \
647         (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
648 
649 #define SCR_LOAD_ABS(reg, n)	SCR_LOAD_R(reg, SCR_NO_FLUSH2, n)
650 #define SCR_LOAD_REL(reg, n)	SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n)
651 #define SCR_LOAD_ABS_F(reg, n)	SCR_LOAD_R(reg, 0, n)
652 #define SCR_LOAD_REL_F(reg, n)	SCR_LOAD_R(reg, SCR_DSA_REL2, n)
653 
654 #define SCR_STORE_ABS(reg, n)	SCR_STORE_R(reg, SCR_NO_FLUSH2, n)
655 #define SCR_STORE_REL(reg, n)	SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n)
656 #define SCR_STORE_ABS_F(reg, n)	SCR_STORE_R(reg, 0, n)
657 #define SCR_STORE_REL_F(reg, n)	SCR_STORE_R(reg, SCR_DSA_REL2, n)
658 
659 
660 /*-----------------------------------------------------------
661  *
662  *	Waiting for Disconnect or Reselect
663  *
664  *-----------------------------------------------------------
665  *
666  *	JUMP            [ | IFTRUE/IFFALSE ( ... ) ]
667  *	<<address>>
668  *
669  *	JUMPR           [ | IFTRUE/IFFALSE ( ... ) ]
670  *	<<distance>>
671  *
672  *	CALL            [ | IFTRUE/IFFALSE ( ... ) ]
673  *	<<address>>
674  *
675  *	CALLR           [ | IFTRUE/IFFALSE ( ... ) ]
676  *	<<distance>>
677  *
678  *	RETURN          [ | IFTRUE/IFFALSE ( ... ) ]
679  *	<<dummy>>
680  *
681  *	INT             [ | IFTRUE/IFFALSE ( ... ) ]
682  *	<<ident>>
683  *
684  *	INT_FLY         [ | IFTRUE/IFFALSE ( ... ) ]
685  *	<<ident>>
686  *
687  *	Conditions:
688  *	     WHEN (phase)
689  *	     IF   (phase)
690  *	     CARRYSET
691  *	     DATA (data, mask)
692  *
693  *-----------------------------------------------------------
694  */
695 
696 #define SCR_NO_OP       0x80000000
697 #define SCR_JUMP        0x80080000
698 #define SCR_JUMP64      0x80480000
699 #define SCR_JUMPR       0x80880000
700 #define SCR_CALL        0x88080000
701 #define SCR_CALLR       0x88880000
702 #define SCR_RETURN      0x90080000
703 #define SCR_INT         0x98080000
704 #define SCR_INT_FLY     0x98180000
705 
706 #define IFFALSE(arg)   (0x00080000 | (arg))
707 #define IFTRUE(arg)    (0x00000000 | (arg))
708 
709 #define WHEN(phase)    (0x00030000 | (phase))
710 #define IF(phase)      (0x00020000 | (phase))
711 
712 #define DATA(D)        (0x00040000 | ((D) & 0xff))
713 #define MASK(D,M)      (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff))
714 
715 #define CARRYSET       (0x00200000)
716 
717 /*-----------------------------------------------------------
718  *
719  *	SCSI  constants.
720  *
721  *-----------------------------------------------------------
722  */
723 
724 /*
725  *	Messages
726  */
727 
728 #define	M_COMPLETE	COMMAND_COMPLETE
729 #define	M_EXTENDED	EXTENDED_MESSAGE
730 #define	M_SAVE_DP	SAVE_POINTERS
731 #define	M_RESTORE_DP	RESTORE_POINTERS
732 #define	M_DISCONNECT	DISCONNECT
733 #define	M_ID_ERROR	INITIATOR_ERROR
734 #define	M_ABORT		ABORT_TASK_SET
735 #define	M_REJECT	MESSAGE_REJECT
736 #define	M_NOOP		NOP
737 #define	M_PARITY	MSG_PARITY_ERROR
738 #define	M_LCOMPLETE	LINKED_CMD_COMPLETE
739 #define	M_FCOMPLETE	LINKED_FLG_CMD_COMPLETE
740 #define	M_RESET		TARGET_RESET
741 #define	M_ABORT_TAG	ABORT_TASK
742 #define	M_CLEAR_QUEUE	CLEAR_TASK_SET
743 #define	M_INIT_REC	INITIATE_RECOVERY
744 #define	M_REL_REC	RELEASE_RECOVERY
745 #define	M_TERMINATE	(0x11)
746 #define	M_SIMPLE_TAG	SIMPLE_QUEUE_TAG
747 #define	M_HEAD_TAG	HEAD_OF_QUEUE_TAG
748 #define	M_ORDERED_TAG	ORDERED_QUEUE_TAG
749 #define	M_IGN_RESIDUE	IGNORE_WIDE_RESIDUE
750 
751 #define	M_X_MODIFY_DP	EXTENDED_MODIFY_DATA_POINTER
752 #define	M_X_SYNC_REQ	EXTENDED_SDTR
753 #define	M_X_WIDE_REQ	EXTENDED_WDTR
754 #define	M_X_PPR_REQ	EXTENDED_PPR
755 
756 /*
757  *	PPR protocol options
758  */
759 #define	PPR_OPT_IU	(0x01)
760 #define	PPR_OPT_DT	(0x02)
761 #define	PPR_OPT_QAS	(0x04)
762 #define PPR_OPT_MASK	(0x07)
763 
764 /*
765  *	Status
766  */
767 
768 #define	S_GOOD		SAM_STAT_GOOD
769 #define	S_CHECK_COND	SAM_STAT_CHECK_CONDITION
770 #define	S_COND_MET	SAM_STAT_CONDITION_MET
771 #define	S_BUSY		SAM_STAT_BUSY
772 #define	S_INT		SAM_STAT_INTERMEDIATE
773 #define	S_INT_COND_MET	SAM_STAT_INTERMEDIATE_CONDITION_MET
774 #define	S_CONFLICT	SAM_STAT_RESERVATION_CONFLICT
775 #define	S_TERMINATED	SAM_STAT_COMMAND_TERMINATED
776 #define	S_QUEUE_FULL	SAM_STAT_TASK_SET_FULL
777 #define	S_ILLEGAL	(0xff)
778 
779 #endif /* defined SYM_DEFS_H */
780