1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Amlogic G12A USB3 + PCIE Combo PHY driver
4 *
5 * Copyright (C) 2017 Amlogic, Inc. All rights reserved
6 * Copyright (C) 2019 BayLibre, SAS
7 * Author: Neil Armstrong <narmstrong@baylibre.com>
8 */
9
10 #include <linux/bitfield.h>
11 #include <linux/bitops.h>
12 #include <linux/clk.h>
13 #include <linux/module.h>
14 #include <linux/of.h>
15 #include <linux/phy/phy.h>
16 #include <linux/regmap.h>
17 #include <linux/reset.h>
18 #include <linux/platform_device.h>
19 #include <dt-bindings/phy/phy.h>
20
21 #define PHY_R0 0x00
22 #define PHY_R0_PCIE_POWER_STATE GENMASK(4, 0)
23 #define PHY_R0_PCIE_USB3_SWITCH GENMASK(6, 5)
24
25 #define PHY_R1 0x04
26 #define PHY_R1_PHY_TX1_TERM_OFFSET GENMASK(4, 0)
27 #define PHY_R1_PHY_TX0_TERM_OFFSET GENMASK(9, 5)
28 #define PHY_R1_PHY_RX1_EQ GENMASK(12, 10)
29 #define PHY_R1_PHY_RX0_EQ GENMASK(15, 13)
30 #define PHY_R1_PHY_LOS_LEVEL GENMASK(20, 16)
31 #define PHY_R1_PHY_LOS_BIAS GENMASK(23, 21)
32 #define PHY_R1_PHY_REF_CLKDIV2 BIT(24)
33 #define PHY_R1_PHY_MPLL_MULTIPLIER GENMASK(31, 25)
34
35 #define PHY_R2 0x08
36 #define PHY_R2_PCS_TX_DEEMPH_GEN2_6DB GENMASK(5, 0)
37 #define PHY_R2_PCS_TX_DEEMPH_GEN2_3P5DB GENMASK(11, 6)
38 #define PHY_R2_PCS_TX_DEEMPH_GEN1 GENMASK(17, 12)
39 #define PHY_R2_PHY_TX_VBOOST_LVL GENMASK(20, 18)
40
41 #define PHY_R4 0x10
42 #define PHY_R4_PHY_CR_WRITE BIT(0)
43 #define PHY_R4_PHY_CR_READ BIT(1)
44 #define PHY_R4_PHY_CR_DATA_IN GENMASK(17, 2)
45 #define PHY_R4_PHY_CR_CAP_DATA BIT(18)
46 #define PHY_R4_PHY_CR_CAP_ADDR BIT(19)
47
48 #define PHY_R5 0x14
49 #define PHY_R5_PHY_CR_DATA_OUT GENMASK(15, 0)
50 #define PHY_R5_PHY_CR_ACK BIT(16)
51 #define PHY_R5_PHY_BS_OUT BIT(17)
52
53 #define PCIE_RESET_DELAY 500
54
55 struct phy_g12a_usb3_pcie_priv {
56 struct regmap *regmap;
57 struct regmap *regmap_cr;
58 struct clk *clk_ref;
59 struct reset_control *reset;
60 struct phy *phy;
61 unsigned int mode;
62 };
63
64 static const struct regmap_config phy_g12a_usb3_pcie_regmap_conf = {
65 .reg_bits = 8,
66 .val_bits = 32,
67 .reg_stride = 4,
68 .max_register = PHY_R5,
69 };
70
phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv * priv,unsigned int addr)71 static int phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv *priv,
72 unsigned int addr)
73 {
74 unsigned int val, reg;
75 int ret;
76
77 reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, addr);
78
79 regmap_write(priv->regmap, PHY_R4, reg);
80 regmap_write(priv->regmap, PHY_R4, reg);
81
82 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_ADDR);
83
84 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
85 (val & PHY_R5_PHY_CR_ACK),
86 5, 1000);
87 if (ret)
88 return ret;
89
90 regmap_write(priv->regmap, PHY_R4, reg);
91
92 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
93 !(val & PHY_R5_PHY_CR_ACK),
94 5, 1000);
95 if (ret)
96 return ret;
97
98 return 0;
99 }
100
phy_g12a_usb3_pcie_cr_bus_read(void * context,unsigned int addr,unsigned int * data)101 static int phy_g12a_usb3_pcie_cr_bus_read(void *context, unsigned int addr,
102 unsigned int *data)
103 {
104 struct phy_g12a_usb3_pcie_priv *priv = context;
105 unsigned int val;
106 int ret;
107
108 ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
109 if (ret)
110 return ret;
111
112 regmap_write(priv->regmap, PHY_R4, 0);
113 regmap_write(priv->regmap, PHY_R4, PHY_R4_PHY_CR_READ);
114
115 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
116 (val & PHY_R5_PHY_CR_ACK),
117 5, 1000);
118 if (ret)
119 return ret;
120
121 *data = FIELD_GET(PHY_R5_PHY_CR_DATA_OUT, val);
122
123 regmap_write(priv->regmap, PHY_R4, 0);
124
125 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
126 !(val & PHY_R5_PHY_CR_ACK),
127 5, 1000);
128 if (ret)
129 return ret;
130
131 return 0;
132 }
133
phy_g12a_usb3_pcie_cr_bus_write(void * context,unsigned int addr,unsigned int data)134 static int phy_g12a_usb3_pcie_cr_bus_write(void *context, unsigned int addr,
135 unsigned int data)
136 {
137 struct phy_g12a_usb3_pcie_priv *priv = context;
138 unsigned int val, reg;
139 int ret;
140
141 ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
142 if (ret)
143 return ret;
144
145 reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, data);
146
147 regmap_write(priv->regmap, PHY_R4, reg);
148 regmap_write(priv->regmap, PHY_R4, reg);
149
150 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_DATA);
151
152 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
153 (val & PHY_R5_PHY_CR_ACK),
154 5, 1000);
155 if (ret)
156 return ret;
157
158 regmap_write(priv->regmap, PHY_R4, reg);
159
160 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
161 (val & PHY_R5_PHY_CR_ACK) == 0,
162 5, 1000);
163 if (ret)
164 return ret;
165
166 regmap_write(priv->regmap, PHY_R4, reg);
167
168 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_WRITE);
169
170 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
171 (val & PHY_R5_PHY_CR_ACK),
172 5, 1000);
173 if (ret)
174 return ret;
175
176 regmap_write(priv->regmap, PHY_R4, reg);
177
178 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
179 (val & PHY_R5_PHY_CR_ACK) == 0,
180 5, 1000);
181 if (ret)
182 return ret;
183
184 return 0;
185 }
186
187 static const struct regmap_config phy_g12a_usb3_pcie_cr_regmap_conf = {
188 .reg_bits = 16,
189 .val_bits = 16,
190 .reg_read = phy_g12a_usb3_pcie_cr_bus_read,
191 .reg_write = phy_g12a_usb3_pcie_cr_bus_write,
192 .max_register = 0xffff,
193 .disable_locking = true,
194 };
195
phy_g12a_usb3_init(struct phy * phy)196 static int phy_g12a_usb3_init(struct phy *phy)
197 {
198 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
199 int data, ret;
200
201 ret = reset_control_reset(priv->reset);
202 if (ret)
203 return ret;
204
205 /* Switch PHY to USB3 */
206 /* TODO figure out how to handle when PCIe was set in the bootloader */
207 regmap_update_bits(priv->regmap, PHY_R0,
208 PHY_R0_PCIE_USB3_SWITCH,
209 PHY_R0_PCIE_USB3_SWITCH);
210
211 /*
212 * WORKAROUND: There is SSPHY suspend bug due to
213 * which USB enumerates
214 * in HS mode instead of SS mode. Workaround it by asserting
215 * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus
216 * mode
217 */
218 ret = regmap_update_bits(priv->regmap_cr, 0x102d, BIT(7), BIT(7));
219 if (ret)
220 return ret;
221
222 ret = regmap_update_bits(priv->regmap_cr, 0x1010, 0xff0, 20);
223 if (ret)
224 return ret;
225
226 /*
227 * Fix RX Equalization setting as follows
228 * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0
229 * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1
230 * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3
231 * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1
232 */
233 ret = regmap_read(priv->regmap_cr, 0x1006, &data);
234 if (ret)
235 return ret;
236
237 data &= ~BIT(6);
238 data |= BIT(7);
239 data &= ~(0x7 << 8);
240 data |= (0x3 << 8);
241 data |= (1 << 11);
242 ret = regmap_write(priv->regmap_cr, 0x1006, data);
243 if (ret)
244 return ret;
245
246 /*
247 * Set EQ and TX launch amplitudes as follows
248 * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22
249 * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127
250 * LANE0.TX_OVRD_DRV_LO.EN set to 1.
251 */
252 ret = regmap_read(priv->regmap_cr, 0x1002, &data);
253 if (ret)
254 return ret;
255
256 data &= ~0x3f80;
257 data |= (0x16 << 7);
258 data &= ~0x7f;
259 data |= (0x7f | BIT(14));
260 ret = regmap_write(priv->regmap_cr, 0x1002, data);
261 if (ret)
262 return ret;
263
264 /* MPLL_LOOP_CTL.PROP_CNTRL = 8 */
265 ret = regmap_update_bits(priv->regmap_cr, 0x30, 0xf << 4, 8 << 4);
266 if (ret)
267 return ret;
268
269 regmap_update_bits(priv->regmap, PHY_R2,
270 PHY_R2_PHY_TX_VBOOST_LVL,
271 FIELD_PREP(PHY_R2_PHY_TX_VBOOST_LVL, 0x4));
272
273 regmap_update_bits(priv->regmap, PHY_R1,
274 PHY_R1_PHY_LOS_BIAS | PHY_R1_PHY_LOS_LEVEL,
275 FIELD_PREP(PHY_R1_PHY_LOS_BIAS, 4) |
276 FIELD_PREP(PHY_R1_PHY_LOS_LEVEL, 9));
277
278 return 0;
279 }
280
phy_g12a_usb3_pcie_power_on(struct phy * phy)281 static int phy_g12a_usb3_pcie_power_on(struct phy *phy)
282 {
283 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
284
285 if (priv->mode == PHY_TYPE_USB3)
286 return 0;
287
288 regmap_update_bits(priv->regmap, PHY_R0,
289 PHY_R0_PCIE_POWER_STATE,
290 FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c));
291
292 return 0;
293 }
294
phy_g12a_usb3_pcie_power_off(struct phy * phy)295 static int phy_g12a_usb3_pcie_power_off(struct phy *phy)
296 {
297 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
298
299 if (priv->mode == PHY_TYPE_USB3)
300 return 0;
301
302 regmap_update_bits(priv->regmap, PHY_R0,
303 PHY_R0_PCIE_POWER_STATE,
304 FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1d));
305
306 return 0;
307 }
308
phy_g12a_usb3_pcie_reset(struct phy * phy)309 static int phy_g12a_usb3_pcie_reset(struct phy *phy)
310 {
311 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
312 int ret;
313
314 if (priv->mode == PHY_TYPE_USB3)
315 return 0;
316
317 ret = reset_control_assert(priv->reset);
318 if (ret)
319 return ret;
320
321 udelay(PCIE_RESET_DELAY);
322
323 ret = reset_control_deassert(priv->reset);
324 if (ret)
325 return ret;
326
327 udelay(PCIE_RESET_DELAY);
328
329 return 0;
330 }
331
phy_g12a_usb3_pcie_init(struct phy * phy)332 static int phy_g12a_usb3_pcie_init(struct phy *phy)
333 {
334 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
335
336 if (priv->mode == PHY_TYPE_USB3)
337 return phy_g12a_usb3_init(phy);
338
339 return 0;
340 }
341
phy_g12a_usb3_pcie_exit(struct phy * phy)342 static int phy_g12a_usb3_pcie_exit(struct phy *phy)
343 {
344 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
345
346 if (priv->mode == PHY_TYPE_USB3)
347 return reset_control_reset(priv->reset);
348
349 return 0;
350 }
351
phy_g12a_usb3_pcie_xlate(struct device * dev,const struct of_phandle_args * args)352 static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev,
353 const struct of_phandle_args *args)
354 {
355 struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev);
356 unsigned int mode;
357
358 if (args->args_count < 1) {
359 dev_err(dev, "invalid number of arguments\n");
360 return ERR_PTR(-EINVAL);
361 }
362
363 mode = args->args[0];
364
365 if (mode != PHY_TYPE_USB3 && mode != PHY_TYPE_PCIE) {
366 dev_err(dev, "invalid phy mode select argument\n");
367 return ERR_PTR(-EINVAL);
368 }
369
370 priv->mode = mode;
371
372 return priv->phy;
373 }
374
375 static const struct phy_ops phy_g12a_usb3_pcie_ops = {
376 .init = phy_g12a_usb3_pcie_init,
377 .exit = phy_g12a_usb3_pcie_exit,
378 .power_on = phy_g12a_usb3_pcie_power_on,
379 .power_off = phy_g12a_usb3_pcie_power_off,
380 .reset = phy_g12a_usb3_pcie_reset,
381 .owner = THIS_MODULE,
382 };
383
phy_g12a_usb3_pcie_probe(struct platform_device * pdev)384 static int phy_g12a_usb3_pcie_probe(struct platform_device *pdev)
385 {
386 struct device *dev = &pdev->dev;
387 struct device_node *np = dev->of_node;
388 struct phy_g12a_usb3_pcie_priv *priv;
389 struct phy_provider *phy_provider;
390 void __iomem *base;
391
392 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
393 if (!priv)
394 return -ENOMEM;
395
396 base = devm_platform_ioremap_resource(pdev, 0);
397 if (IS_ERR(base))
398 return PTR_ERR(base);
399
400 priv->regmap = devm_regmap_init_mmio(dev, base,
401 &phy_g12a_usb3_pcie_regmap_conf);
402 if (IS_ERR(priv->regmap))
403 return PTR_ERR(priv->regmap);
404
405 priv->regmap_cr = devm_regmap_init(dev, NULL, priv,
406 &phy_g12a_usb3_pcie_cr_regmap_conf);
407 if (IS_ERR(priv->regmap_cr))
408 return PTR_ERR(priv->regmap_cr);
409
410 priv->clk_ref = devm_clk_get_enabled(dev, "ref_clk");
411 if (IS_ERR(priv->clk_ref))
412 return PTR_ERR(priv->clk_ref);
413
414 priv->reset = devm_reset_control_array_get_exclusive(dev);
415 if (IS_ERR(priv->reset))
416 return PTR_ERR(priv->reset);
417
418 priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops);
419 if (IS_ERR(priv->phy))
420 return dev_err_probe(dev, PTR_ERR(priv->phy), "failed to create PHY\n");
421
422 phy_set_drvdata(priv->phy, priv);
423 dev_set_drvdata(dev, priv);
424
425 phy_provider = devm_of_phy_provider_register(dev,
426 phy_g12a_usb3_pcie_xlate);
427 return PTR_ERR_OR_ZERO(phy_provider);
428 }
429
430 static const struct of_device_id phy_g12a_usb3_pcie_of_match[] = {
431 { .compatible = "amlogic,g12a-usb3-pcie-phy", },
432 { },
433 };
434 MODULE_DEVICE_TABLE(of, phy_g12a_usb3_pcie_of_match);
435
436 static struct platform_driver phy_g12a_usb3_pcie_driver = {
437 .probe = phy_g12a_usb3_pcie_probe,
438 .driver = {
439 .name = "phy-g12a-usb3-pcie",
440 .of_match_table = phy_g12a_usb3_pcie_of_match,
441 },
442 };
443 module_platform_driver(phy_g12a_usb3_pcie_driver);
444
445 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
446 MODULE_DESCRIPTION("Amlogic G12A USB3 + PCIE Combo PHY driver");
447 MODULE_LICENSE("GPL v2");
448