1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * 8250-core based driver for the OMAP internal UART
4 *
5 * based on omap-serial.c, Copyright (C) 2010 Texas Instruments.
6 *
7 * Copyright (C) 2014 Sebastian Andrzej Siewior
8 *
9 */
10
11 #include <linux/atomic.h>
12 #include <linux/clk.h>
13 #include <linux/device.h>
14 #include <linux/io.h>
15 #include <linux/module.h>
16 #include <linux/serial_8250.h>
17 #include <linux/serial_reg.h>
18 #include <linux/tty_flip.h>
19 #include <linux/platform_device.h>
20 #include <linux/slab.h>
21 #include <linux/of.h>
22 #include <linux/of_irq.h>
23 #include <linux/delay.h>
24 #include <linux/pm_runtime.h>
25 #include <linux/console.h>
26 #include <linux/pm_qos.h>
27 #include <linux/pm_wakeirq.h>
28 #include <linux/dma-mapping.h>
29 #include <linux/sys_soc.h>
30
31 #include "8250.h"
32
33 #define DEFAULT_CLK_SPEED 48000000
34 #define OMAP_UART_REGSHIFT 2
35
36 #define UART_ERRATA_i202_MDR1_ACCESS (1 << 0)
37 #define OMAP_UART_WER_HAS_TX_WAKEUP (1 << 1)
38 #define OMAP_DMA_TX_KICK (1 << 2)
39 /*
40 * See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
41 * The same errata is applicable to AM335x and DRA7x processors too.
42 */
43 #define UART_ERRATA_CLOCK_DISABLE (1 << 3)
44 #define UART_HAS_EFR2 BIT(4)
45 #define UART_HAS_RHR_IT_DIS BIT(5)
46 #define UART_RX_TIMEOUT_QUIRK BIT(6)
47 #define UART_HAS_NATIVE_RS485 BIT(7)
48
49 #define OMAP_UART_FCR_RX_TRIG 6
50 #define OMAP_UART_FCR_TX_TRIG 4
51
52 /* SCR register bitmasks */
53 #define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7)
54 #define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK (1 << 6)
55 #define OMAP_UART_SCR_TX_EMPTY (1 << 3)
56 #define OMAP_UART_SCR_DMAMODE_MASK (3 << 1)
57 #define OMAP_UART_SCR_DMAMODE_1 (1 << 1)
58 #define OMAP_UART_SCR_DMAMODE_CTL (1 << 0)
59
60 /* MVR register bitmasks */
61 #define OMAP_UART_MVR_SCHEME_SHIFT 30
62 #define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
63 #define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
64 #define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
65 #define OMAP_UART_MVR_MAJ_MASK 0x700
66 #define OMAP_UART_MVR_MAJ_SHIFT 8
67 #define OMAP_UART_MVR_MIN_MASK 0x3f
68
69 /* SYSC register bitmasks */
70 #define OMAP_UART_SYSC_SOFTRESET (1 << 1)
71
72 /* SYSS register bitmasks */
73 #define OMAP_UART_SYSS_RESETDONE (1 << 0)
74
75 #define UART_TI752_TLR_TX 0
76 #define UART_TI752_TLR_RX 4
77
78 #define TRIGGER_TLR_MASK(x) ((x & 0x3c) >> 2)
79 #define TRIGGER_FCR_MASK(x) (x & 3)
80
81 /* Enable XON/XOFF flow control on output */
82 #define OMAP_UART_SW_TX 0x08
83 /* Enable XON/XOFF flow control on input */
84 #define OMAP_UART_SW_RX 0x02
85
86 #define OMAP_UART_WER_MOD_WKUP 0x7f
87 #define OMAP_UART_TX_WAKEUP_EN (1 << 7)
88
89 #define TX_TRIGGER 1
90 #define RX_TRIGGER 48
91
92 #define OMAP_UART_TCR_RESTORE(x) ((x / 4) << 4)
93 #define OMAP_UART_TCR_HALT(x) ((x / 4) << 0)
94
95 #define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
96
97 #define OMAP_UART_REV_46 0x0406
98 #define OMAP_UART_REV_52 0x0502
99 #define OMAP_UART_REV_63 0x0603
100
101 /* Interrupt Enable Register 2 */
102 #define UART_OMAP_IER2 0x1B
103 #define UART_OMAP_IER2_RHR_IT_DIS BIT(2)
104
105 /* Mode Definition Register 3 */
106 #define UART_OMAP_MDR3 0x20
107 #define UART_OMAP_MDR3_DIR_POL BIT(3)
108 #define UART_OMAP_MDR3_DIR_EN BIT(4)
109
110 /* Enhanced features register 2 */
111 #define UART_OMAP_EFR2 0x23
112 #define UART_OMAP_EFR2_TIMEOUT_BEHAVE BIT(6)
113
114 /* RX FIFO occupancy indicator */
115 #define UART_OMAP_RX_LVL 0x19
116
117 /* Timeout low and High */
118 #define UART_OMAP_TO_L 0x26
119 #define UART_OMAP_TO_H 0x27
120
121 struct omap8250_priv {
122 void __iomem *membase;
123 int line;
124 u8 habit;
125 u8 mdr1;
126 u8 mdr3;
127 u8 efr;
128 u8 scr;
129 u8 wer;
130 u8 xon;
131 u8 xoff;
132 u8 delayed_restore;
133 u16 quot;
134
135 u8 tx_trigger;
136 u8 rx_trigger;
137 atomic_t active;
138 bool is_suspending;
139 int wakeirq;
140 u32 latency;
141 u32 calc_latency;
142 struct pm_qos_request pm_qos_request;
143 struct work_struct qos_work;
144 struct uart_8250_dma omap8250_dma;
145 spinlock_t rx_dma_lock;
146 bool rx_dma_broken;
147 bool throttled;
148 };
149
150 struct omap8250_dma_params {
151 u32 rx_size;
152 u8 rx_trigger;
153 u8 tx_trigger;
154 };
155
156 struct omap8250_platdata {
157 struct omap8250_dma_params *dma_params;
158 u8 habit;
159 };
160
161 #ifdef CONFIG_SERIAL_8250_DMA
162 static void omap_8250_rx_dma_flush(struct uart_8250_port *p);
163 #else
omap_8250_rx_dma_flush(struct uart_8250_port * p)164 static inline void omap_8250_rx_dma_flush(struct uart_8250_port *p) { }
165 #endif
166
uart_read(struct omap8250_priv * priv,u32 reg)167 static u32 uart_read(struct omap8250_priv *priv, u32 reg)
168 {
169 return readl(priv->membase + (reg << OMAP_UART_REGSHIFT));
170 }
171
172 /*
173 * Called on runtime PM resume path from omap8250_restore_regs(), and
174 * omap8250_set_mctrl().
175 */
__omap8250_set_mctrl(struct uart_port * port,unsigned int mctrl)176 static void __omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
177 {
178 struct uart_8250_port *up = up_to_u8250p(port);
179 struct omap8250_priv *priv = up->port.private_data;
180 u8 lcr;
181
182 serial8250_do_set_mctrl(port, mctrl);
183
184 if (!mctrl_gpio_to_gpiod(up->gpios, UART_GPIO_RTS)) {
185 /*
186 * Turn off autoRTS if RTS is lowered and restore autoRTS
187 * setting if RTS is raised
188 */
189 lcr = serial_in(up, UART_LCR);
190 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
191 if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
192 priv->efr |= UART_EFR_RTS;
193 else
194 priv->efr &= ~UART_EFR_RTS;
195 serial_out(up, UART_EFR, priv->efr);
196 serial_out(up, UART_LCR, lcr);
197 }
198 }
199
omap8250_set_mctrl(struct uart_port * port,unsigned int mctrl)200 static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
201 {
202 int err;
203
204 err = pm_runtime_resume_and_get(port->dev);
205 if (err)
206 return;
207
208 __omap8250_set_mctrl(port, mctrl);
209
210 pm_runtime_mark_last_busy(port->dev);
211 pm_runtime_put_autosuspend(port->dev);
212 }
213
214 /*
215 * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460)
216 * The access to uart register after MDR1 Access
217 * causes UART to corrupt data.
218 *
219 * Need a delay =
220 * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
221 * give 10 times as much
222 */
omap_8250_mdr1_errataset(struct uart_8250_port * up,struct omap8250_priv * priv)223 static void omap_8250_mdr1_errataset(struct uart_8250_port *up,
224 struct omap8250_priv *priv)
225 {
226 serial_out(up, UART_OMAP_MDR1, priv->mdr1);
227 udelay(2);
228 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT |
229 UART_FCR_CLEAR_RCVR);
230 }
231
omap_8250_get_divisor(struct uart_port * port,unsigned int baud,struct omap8250_priv * priv)232 static void omap_8250_get_divisor(struct uart_port *port, unsigned int baud,
233 struct omap8250_priv *priv)
234 {
235 unsigned int uartclk = port->uartclk;
236 unsigned int div_13, div_16;
237 unsigned int abs_d13, abs_d16;
238
239 /*
240 * Old custom speed handling.
241 */
242 if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) {
243 priv->quot = port->custom_divisor & UART_DIV_MAX;
244 /*
245 * I assume that nobody is using this. But hey, if somebody
246 * would like to specify the divisor _and_ the mode then the
247 * driver is ready and waiting for it.
248 */
249 if (port->custom_divisor & (1 << 16))
250 priv->mdr1 = UART_OMAP_MDR1_13X_MODE;
251 else
252 priv->mdr1 = UART_OMAP_MDR1_16X_MODE;
253 return;
254 }
255 div_13 = DIV_ROUND_CLOSEST(uartclk, 13 * baud);
256 div_16 = DIV_ROUND_CLOSEST(uartclk, 16 * baud);
257
258 if (!div_13)
259 div_13 = 1;
260 if (!div_16)
261 div_16 = 1;
262
263 abs_d13 = abs(baud - uartclk / 13 / div_13);
264 abs_d16 = abs(baud - uartclk / 16 / div_16);
265
266 if (abs_d13 >= abs_d16) {
267 priv->mdr1 = UART_OMAP_MDR1_16X_MODE;
268 priv->quot = div_16;
269 } else {
270 priv->mdr1 = UART_OMAP_MDR1_13X_MODE;
271 priv->quot = div_13;
272 }
273 }
274
omap8250_update_scr(struct uart_8250_port * up,struct omap8250_priv * priv)275 static void omap8250_update_scr(struct uart_8250_port *up,
276 struct omap8250_priv *priv)
277 {
278 u8 old_scr;
279
280 old_scr = serial_in(up, UART_OMAP_SCR);
281 if (old_scr == priv->scr)
282 return;
283
284 /*
285 * The manual recommends not to enable the DMA mode selector in the SCR
286 * (instead of the FCR) register _and_ selecting the DMA mode as one
287 * register write because this may lead to malfunction.
288 */
289 if (priv->scr & OMAP_UART_SCR_DMAMODE_MASK)
290 serial_out(up, UART_OMAP_SCR,
291 priv->scr & ~OMAP_UART_SCR_DMAMODE_MASK);
292 serial_out(up, UART_OMAP_SCR, priv->scr);
293 }
294
omap8250_update_mdr1(struct uart_8250_port * up,struct omap8250_priv * priv)295 static void omap8250_update_mdr1(struct uart_8250_port *up,
296 struct omap8250_priv *priv)
297 {
298 if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS)
299 omap_8250_mdr1_errataset(up, priv);
300 else
301 serial_out(up, UART_OMAP_MDR1, priv->mdr1);
302 }
303
omap8250_restore_regs(struct uart_8250_port * up)304 static void omap8250_restore_regs(struct uart_8250_port *up)
305 {
306 struct omap8250_priv *priv = up->port.private_data;
307 struct uart_8250_dma *dma = up->dma;
308 u8 mcr = serial8250_in_MCR(up);
309
310 /* Port locked to synchronize UART_IER access against the console. */
311 lockdep_assert_held_once(&up->port.lock);
312
313 if (dma && dma->tx_running) {
314 /*
315 * TCSANOW requests the change to occur immediately however if
316 * we have a TX-DMA operation in progress then it has been
317 * observed that it might stall and never complete. Therefore we
318 * delay DMA completes to prevent this hang from happen.
319 */
320 priv->delayed_restore = 1;
321 return;
322 }
323
324 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
325 serial_out(up, UART_EFR, UART_EFR_ECB);
326
327 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
328 serial8250_out_MCR(up, mcr | UART_MCR_TCRTLR);
329 serial_out(up, UART_FCR, up->fcr);
330
331 omap8250_update_scr(up, priv);
332
333 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
334
335 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_RESTORE(16) |
336 OMAP_UART_TCR_HALT(52));
337 serial_out(up, UART_TI752_TLR,
338 TRIGGER_TLR_MASK(priv->tx_trigger) << UART_TI752_TLR_TX |
339 TRIGGER_TLR_MASK(priv->rx_trigger) << UART_TI752_TLR_RX);
340
341 serial_out(up, UART_LCR, 0);
342
343 /* drop TCR + TLR access, we setup XON/XOFF later */
344 serial8250_out_MCR(up, mcr);
345
346 serial_out(up, UART_IER, up->ier);
347
348 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
349 serial_dl_write(up, priv->quot);
350
351 serial_out(up, UART_EFR, priv->efr);
352
353 /* Configure flow control */
354 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
355 serial_out(up, UART_XON1, priv->xon);
356 serial_out(up, UART_XOFF1, priv->xoff);
357
358 serial_out(up, UART_LCR, up->lcr);
359
360 omap8250_update_mdr1(up, priv);
361
362 __omap8250_set_mctrl(&up->port, up->port.mctrl);
363
364 serial_out(up, UART_OMAP_MDR3, priv->mdr3);
365
366 if (up->port.rs485.flags & SER_RS485_ENABLED &&
367 up->port.rs485_config == serial8250_em485_config)
368 serial8250_em485_stop_tx(up);
369 }
370
371 /*
372 * OMAP can use "CLK / (16 or 13) / div" for baud rate. And then we have have
373 * some differences in how we want to handle flow control.
374 */
omap_8250_set_termios(struct uart_port * port,struct ktermios * termios,const struct ktermios * old)375 static void omap_8250_set_termios(struct uart_port *port,
376 struct ktermios *termios,
377 const struct ktermios *old)
378 {
379 struct uart_8250_port *up = up_to_u8250p(port);
380 struct omap8250_priv *priv = up->port.private_data;
381 unsigned char cval = 0;
382 unsigned int baud;
383
384 cval = UART_LCR_WLEN(tty_get_char_size(termios->c_cflag));
385
386 if (termios->c_cflag & CSTOPB)
387 cval |= UART_LCR_STOP;
388 if (termios->c_cflag & PARENB)
389 cval |= UART_LCR_PARITY;
390 if (!(termios->c_cflag & PARODD))
391 cval |= UART_LCR_EPAR;
392 if (termios->c_cflag & CMSPAR)
393 cval |= UART_LCR_SPAR;
394
395 /*
396 * Ask the core to calculate the divisor for us.
397 */
398 baud = uart_get_baud_rate(port, termios, old,
399 port->uartclk / 16 / UART_DIV_MAX,
400 port->uartclk / 13);
401 omap_8250_get_divisor(port, baud, priv);
402
403 /*
404 * Ok, we're now changing the port state. Do it with
405 * interrupts disabled.
406 */
407 pm_runtime_get_sync(port->dev);
408 uart_port_lock_irq(port);
409
410 /*
411 * Update the per-port timeout.
412 */
413 uart_update_timeout(port, termios->c_cflag, baud);
414
415 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
416 if (termios->c_iflag & INPCK)
417 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
418 if (termios->c_iflag & (IGNBRK | PARMRK))
419 up->port.read_status_mask |= UART_LSR_BI;
420
421 /*
422 * Characters to ignore
423 */
424 up->port.ignore_status_mask = 0;
425 if (termios->c_iflag & IGNPAR)
426 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
427 if (termios->c_iflag & IGNBRK) {
428 up->port.ignore_status_mask |= UART_LSR_BI;
429 /*
430 * If we're ignoring parity and break indicators,
431 * ignore overruns too (for real raw support).
432 */
433 if (termios->c_iflag & IGNPAR)
434 up->port.ignore_status_mask |= UART_LSR_OE;
435 }
436
437 /*
438 * ignore all characters if CREAD is not set
439 */
440 if ((termios->c_cflag & CREAD) == 0)
441 up->port.ignore_status_mask |= UART_LSR_DR;
442
443 /*
444 * Modem status interrupts
445 */
446 up->ier &= ~UART_IER_MSI;
447 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
448 up->ier |= UART_IER_MSI;
449
450 up->lcr = cval;
451 /* Up to here it was mostly serial8250_do_set_termios() */
452
453 /*
454 * We enable TRIG_GRANU for RX and TX and additionally we set
455 * SCR_TX_EMPTY bit. The result is the following:
456 * - RX_TRIGGER amount of bytes in the FIFO will cause an interrupt.
457 * - less than RX_TRIGGER number of bytes will also cause an interrupt
458 * once the UART decides that there no new bytes arriving.
459 * - Once THRE is enabled, the interrupt will be fired once the FIFO is
460 * empty - the trigger level is ignored here.
461 *
462 * Once DMA is enabled:
463 * - UART will assert the TX DMA line once there is room for TX_TRIGGER
464 * bytes in the TX FIFO. On each assert the DMA engine will move
465 * TX_TRIGGER bytes into the FIFO.
466 * - UART will assert the RX DMA line once there are RX_TRIGGER bytes in
467 * the FIFO and move RX_TRIGGER bytes.
468 * This is because threshold and trigger values are the same.
469 */
470 up->fcr = UART_FCR_ENABLE_FIFO;
471 up->fcr |= TRIGGER_FCR_MASK(priv->tx_trigger) << OMAP_UART_FCR_TX_TRIG;
472 up->fcr |= TRIGGER_FCR_MASK(priv->rx_trigger) << OMAP_UART_FCR_RX_TRIG;
473
474 priv->scr = OMAP_UART_SCR_RX_TRIG_GRANU1_MASK | OMAP_UART_SCR_TX_EMPTY |
475 OMAP_UART_SCR_TX_TRIG_GRANU1_MASK;
476
477 if (up->dma)
478 priv->scr |= OMAP_UART_SCR_DMAMODE_1 |
479 OMAP_UART_SCR_DMAMODE_CTL;
480
481 priv->xon = termios->c_cc[VSTART];
482 priv->xoff = termios->c_cc[VSTOP];
483
484 priv->efr = 0;
485 up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
486
487 if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW &&
488 !mctrl_gpio_to_gpiod(up->gpios, UART_GPIO_RTS) &&
489 !mctrl_gpio_to_gpiod(up->gpios, UART_GPIO_CTS)) {
490 /* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
491 up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
492 priv->efr |= UART_EFR_CTS;
493 } else if (up->port.flags & UPF_SOFT_FLOW) {
494 /*
495 * OMAP rx s/w flow control is borked; the transmitter remains
496 * stuck off even if rx flow control is subsequently disabled
497 */
498
499 /*
500 * IXOFF Flag:
501 * Enable XON/XOFF flow control on output.
502 * Transmit XON1, XOFF1
503 */
504 if (termios->c_iflag & IXOFF) {
505 up->port.status |= UPSTAT_AUTOXOFF;
506 priv->efr |= OMAP_UART_SW_TX;
507 }
508 }
509 omap8250_restore_regs(up);
510
511 uart_port_unlock_irq(&up->port);
512 pm_runtime_mark_last_busy(port->dev);
513 pm_runtime_put_autosuspend(port->dev);
514
515 /* calculate wakeup latency constraint */
516 priv->calc_latency = USEC_PER_SEC * 64 * 8 / baud;
517 priv->latency = priv->calc_latency;
518
519 schedule_work(&priv->qos_work);
520
521 /* Don't rewrite B0 */
522 if (tty_termios_baud_rate(termios))
523 tty_termios_encode_baud_rate(termios, baud, baud);
524 }
525
526 /* same as 8250 except that we may have extra flow bits set in EFR */
omap_8250_pm(struct uart_port * port,unsigned int state,unsigned int oldstate)527 static void omap_8250_pm(struct uart_port *port, unsigned int state,
528 unsigned int oldstate)
529 {
530 struct uart_8250_port *up = up_to_u8250p(port);
531 u8 efr;
532
533 pm_runtime_get_sync(port->dev);
534
535 /* Synchronize UART_IER access against the console. */
536 uart_port_lock_irq(port);
537
538 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
539 efr = serial_in(up, UART_EFR);
540 serial_out(up, UART_EFR, efr | UART_EFR_ECB);
541 serial_out(up, UART_LCR, 0);
542
543 serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
544 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
545 serial_out(up, UART_EFR, efr);
546 serial_out(up, UART_LCR, 0);
547
548 uart_port_unlock_irq(port);
549
550 pm_runtime_mark_last_busy(port->dev);
551 pm_runtime_put_autosuspend(port->dev);
552 }
553
omap_serial_fill_features_erratas(struct uart_8250_port * up,struct omap8250_priv * priv)554 static void omap_serial_fill_features_erratas(struct uart_8250_port *up,
555 struct omap8250_priv *priv)
556 {
557 static const struct soc_device_attribute k3_soc_devices[] = {
558 { .family = "AM65X", },
559 { .family = "J721E", .revision = "SR1.0" },
560 { /* sentinel */ }
561 };
562 u32 mvr, scheme;
563 u16 revision, major, minor;
564
565 mvr = uart_read(priv, UART_OMAP_MVER);
566
567 /* Check revision register scheme */
568 scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
569
570 switch (scheme) {
571 case 0: /* Legacy Scheme: OMAP2/3 */
572 /* MINOR_REV[0:4], MAJOR_REV[4:7] */
573 major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
574 OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
575 minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
576 break;
577 case 1:
578 /* New Scheme: OMAP4+ */
579 /* MINOR_REV[0:5], MAJOR_REV[8:10] */
580 major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
581 OMAP_UART_MVR_MAJ_SHIFT;
582 minor = (mvr & OMAP_UART_MVR_MIN_MASK);
583 break;
584 default:
585 dev_warn(up->port.dev,
586 "Unknown revision, defaulting to highest\n");
587 /* highest possible revision */
588 major = 0xff;
589 minor = 0xff;
590 }
591 /* normalize revision for the driver */
592 revision = UART_BUILD_REVISION(major, minor);
593
594 switch (revision) {
595 case OMAP_UART_REV_46:
596 priv->habit |= UART_ERRATA_i202_MDR1_ACCESS;
597 break;
598 case OMAP_UART_REV_52:
599 priv->habit |= UART_ERRATA_i202_MDR1_ACCESS |
600 OMAP_UART_WER_HAS_TX_WAKEUP;
601 break;
602 case OMAP_UART_REV_63:
603 priv->habit |= UART_ERRATA_i202_MDR1_ACCESS |
604 OMAP_UART_WER_HAS_TX_WAKEUP;
605 break;
606 default:
607 break;
608 }
609
610 /*
611 * AM65x SR1.0, AM65x SR2.0 and J721e SR1.0 don't
612 * don't have RHR_IT_DIS bit in IER2 register. So drop to flag
613 * to enable errata workaround.
614 */
615 if (soc_device_match(k3_soc_devices))
616 priv->habit &= ~UART_HAS_RHR_IT_DIS;
617 }
618
omap8250_uart_qos_work(struct work_struct * work)619 static void omap8250_uart_qos_work(struct work_struct *work)
620 {
621 struct omap8250_priv *priv;
622
623 priv = container_of(work, struct omap8250_priv, qos_work);
624 cpu_latency_qos_update_request(&priv->pm_qos_request, priv->latency);
625 }
626
627 #ifdef CONFIG_SERIAL_8250_DMA
628 static int omap_8250_dma_handle_irq(struct uart_port *port);
629 #endif
630
omap8250_irq(int irq,void * dev_id)631 static irqreturn_t omap8250_irq(int irq, void *dev_id)
632 {
633 struct omap8250_priv *priv = dev_id;
634 struct uart_8250_port *up = serial8250_get_port(priv->line);
635 struct uart_port *port = &up->port;
636 unsigned int iir, lsr;
637 int ret;
638
639 pm_runtime_get_noresume(port->dev);
640
641 /* Shallow idle state wake-up to an IO interrupt? */
642 if (atomic_add_unless(&priv->active, 1, 1)) {
643 priv->latency = priv->calc_latency;
644 schedule_work(&priv->qos_work);
645 }
646
647 #ifdef CONFIG_SERIAL_8250_DMA
648 if (up->dma) {
649 ret = omap_8250_dma_handle_irq(port);
650 pm_runtime_mark_last_busy(port->dev);
651 pm_runtime_put(port->dev);
652 return IRQ_RETVAL(ret);
653 }
654 #endif
655
656 lsr = serial_port_in(port, UART_LSR);
657 iir = serial_port_in(port, UART_IIR);
658 ret = serial8250_handle_irq(port, iir);
659
660 /*
661 * On K3 SoCs, it is observed that RX TIMEOUT is signalled after
662 * FIFO has been drained or erroneously.
663 * So apply solution of Errata i2310 as mentioned in
664 * https://www.ti.com/lit/pdf/sprz536
665 */
666 if (priv->habit & UART_RX_TIMEOUT_QUIRK &&
667 (iir & UART_IIR_RX_TIMEOUT) == UART_IIR_RX_TIMEOUT &&
668 serial_port_in(port, UART_OMAP_RX_LVL) == 0) {
669 unsigned char efr2, timeout_h, timeout_l;
670
671 efr2 = serial_in(up, UART_OMAP_EFR2);
672 timeout_h = serial_in(up, UART_OMAP_TO_H);
673 timeout_l = serial_in(up, UART_OMAP_TO_L);
674 serial_out(up, UART_OMAP_TO_H, 0xFF);
675 serial_out(up, UART_OMAP_TO_L, 0xFF);
676 serial_out(up, UART_OMAP_EFR2, UART_OMAP_EFR2_TIMEOUT_BEHAVE);
677 serial_in(up, UART_IIR);
678 serial_out(up, UART_OMAP_EFR2, efr2);
679 serial_out(up, UART_OMAP_TO_H, timeout_h);
680 serial_out(up, UART_OMAP_TO_L, timeout_l);
681 }
682
683 /* Stop processing interrupts on input overrun */
684 if ((lsr & UART_LSR_OE) && up->overrun_backoff_time_ms > 0) {
685 unsigned long delay;
686
687 /* Synchronize UART_IER access against the console. */
688 uart_port_lock(port);
689 up->ier = port->serial_in(port, UART_IER);
690 if (up->ier & (UART_IER_RLSI | UART_IER_RDI)) {
691 port->ops->stop_rx(port);
692 } else {
693 /* Keep restarting the timer until
694 * the input overrun subsides.
695 */
696 cancel_delayed_work(&up->overrun_backoff);
697 }
698 uart_port_unlock(port);
699
700 delay = msecs_to_jiffies(up->overrun_backoff_time_ms);
701 schedule_delayed_work(&up->overrun_backoff, delay);
702 }
703
704 pm_runtime_mark_last_busy(port->dev);
705 pm_runtime_put(port->dev);
706
707 return IRQ_RETVAL(ret);
708 }
709
omap_8250_startup(struct uart_port * port)710 static int omap_8250_startup(struct uart_port *port)
711 {
712 struct uart_8250_port *up = up_to_u8250p(port);
713 struct omap8250_priv *priv = port->private_data;
714 struct uart_8250_dma *dma = &priv->omap8250_dma;
715 int ret;
716
717 if (priv->wakeirq) {
718 ret = dev_pm_set_dedicated_wake_irq(port->dev, priv->wakeirq);
719 if (ret)
720 return ret;
721 }
722
723 pm_runtime_get_sync(port->dev);
724
725 serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
726
727 serial_out(up, UART_LCR, UART_LCR_WLEN8);
728
729 up->lsr_saved_flags = 0;
730 up->msr_saved_flags = 0;
731
732 /* Disable DMA for console UART */
733 if (dma->fn && !uart_console(port)) {
734 up->dma = &priv->omap8250_dma;
735 ret = serial8250_request_dma(up);
736 if (ret) {
737 dev_warn_ratelimited(port->dev,
738 "failed to request DMA\n");
739 up->dma = NULL;
740 }
741 } else {
742 up->dma = NULL;
743 }
744
745 /* Synchronize UART_IER access against the console. */
746 uart_port_lock_irq(port);
747 up->ier = UART_IER_RLSI | UART_IER_RDI;
748 serial_out(up, UART_IER, up->ier);
749 uart_port_unlock_irq(port);
750
751 #ifdef CONFIG_PM
752 up->capabilities |= UART_CAP_RPM;
753 #endif
754
755 /* Enable module level wake up */
756 priv->wer = OMAP_UART_WER_MOD_WKUP;
757 if (priv->habit & OMAP_UART_WER_HAS_TX_WAKEUP)
758 priv->wer |= OMAP_UART_TX_WAKEUP_EN;
759 serial_out(up, UART_OMAP_WER, priv->wer);
760
761 if (up->dma && !(priv->habit & UART_HAS_EFR2)) {
762 uart_port_lock_irq(port);
763 up->dma->rx_dma(up);
764 uart_port_unlock_irq(port);
765 }
766
767 enable_irq(up->port.irq);
768
769 pm_runtime_mark_last_busy(port->dev);
770 pm_runtime_put_autosuspend(port->dev);
771 return 0;
772 }
773
omap_8250_shutdown(struct uart_port * port)774 static void omap_8250_shutdown(struct uart_port *port)
775 {
776 struct uart_8250_port *up = up_to_u8250p(port);
777 struct omap8250_priv *priv = port->private_data;
778
779 flush_work(&priv->qos_work);
780 if (up->dma)
781 omap_8250_rx_dma_flush(up);
782
783 pm_runtime_get_sync(port->dev);
784
785 serial_out(up, UART_OMAP_WER, 0);
786 if (priv->habit & UART_HAS_EFR2)
787 serial_out(up, UART_OMAP_EFR2, 0x0);
788
789 /* Synchronize UART_IER access against the console. */
790 uart_port_lock_irq(port);
791 up->ier = 0;
792 serial_out(up, UART_IER, 0);
793 uart_port_unlock_irq(port);
794 disable_irq_nosync(up->port.irq);
795 dev_pm_clear_wake_irq(port->dev);
796
797 serial8250_release_dma(up);
798 up->dma = NULL;
799
800 /*
801 * Disable break condition and FIFOs
802 */
803 if (up->lcr & UART_LCR_SBC)
804 serial_out(up, UART_LCR, up->lcr & ~UART_LCR_SBC);
805 serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
806
807 pm_runtime_mark_last_busy(port->dev);
808 pm_runtime_put_autosuspend(port->dev);
809 }
810
omap_8250_throttle(struct uart_port * port)811 static void omap_8250_throttle(struct uart_port *port)
812 {
813 struct omap8250_priv *priv = port->private_data;
814 unsigned long flags;
815
816 pm_runtime_get_sync(port->dev);
817
818 uart_port_lock_irqsave(port, &flags);
819 port->ops->stop_rx(port);
820 priv->throttled = true;
821 uart_port_unlock_irqrestore(port, flags);
822
823 pm_runtime_mark_last_busy(port->dev);
824 pm_runtime_put_autosuspend(port->dev);
825 }
826
omap_8250_unthrottle(struct uart_port * port)827 static void omap_8250_unthrottle(struct uart_port *port)
828 {
829 struct omap8250_priv *priv = port->private_data;
830 struct uart_8250_port *up = up_to_u8250p(port);
831 unsigned long flags;
832
833 pm_runtime_get_sync(port->dev);
834
835 /* Synchronize UART_IER access against the console. */
836 uart_port_lock_irqsave(port, &flags);
837 priv->throttled = false;
838 if (up->dma)
839 up->dma->rx_dma(up);
840 up->ier |= UART_IER_RLSI | UART_IER_RDI;
841 port->read_status_mask |= UART_LSR_DR;
842 serial_out(up, UART_IER, up->ier);
843 uart_port_unlock_irqrestore(port, flags);
844
845 pm_runtime_mark_last_busy(port->dev);
846 pm_runtime_put_autosuspend(port->dev);
847 }
848
omap8250_rs485_config(struct uart_port * port,struct ktermios * termios,struct serial_rs485 * rs485)849 static int omap8250_rs485_config(struct uart_port *port,
850 struct ktermios *termios,
851 struct serial_rs485 *rs485)
852 {
853 struct omap8250_priv *priv = port->private_data;
854 struct uart_8250_port *up = up_to_u8250p(port);
855 u32 fixed_delay_rts_before_send = 0;
856 u32 fixed_delay_rts_after_send = 0;
857 unsigned int baud;
858
859 /*
860 * There is a fixed delay of 3 bit clock cycles after the TX shift
861 * register is going empty to allow time for the stop bit to transition
862 * through the transceiver before direction is changed to receive.
863 *
864 * Additionally there appears to be a 1 bit clock delay between writing
865 * to the THR register and transmission of the start bit, per page 8783
866 * of the AM65 TRM: https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
867 */
868 if (priv->quot) {
869 if (priv->mdr1 == UART_OMAP_MDR1_16X_MODE)
870 baud = port->uartclk / (16 * priv->quot);
871 else
872 baud = port->uartclk / (13 * priv->quot);
873
874 fixed_delay_rts_after_send = 3 * MSEC_PER_SEC / baud;
875 fixed_delay_rts_before_send = 1 * MSEC_PER_SEC / baud;
876 }
877
878 /*
879 * Fall back to RS485 software emulation if the UART is missing
880 * hardware support, if the device tree specifies an mctrl_gpio
881 * (indicates that RTS is unavailable due to a pinmux conflict)
882 * or if the requested delays exceed the fixed hardware delays.
883 */
884 if (!(priv->habit & UART_HAS_NATIVE_RS485) ||
885 mctrl_gpio_to_gpiod(up->gpios, UART_GPIO_RTS) ||
886 rs485->delay_rts_after_send > fixed_delay_rts_after_send ||
887 rs485->delay_rts_before_send > fixed_delay_rts_before_send) {
888 priv->mdr3 &= ~UART_OMAP_MDR3_DIR_EN;
889 serial_out(up, UART_OMAP_MDR3, priv->mdr3);
890
891 port->rs485_config = serial8250_em485_config;
892 return serial8250_em485_config(port, termios, rs485);
893 }
894
895 rs485->delay_rts_after_send = fixed_delay_rts_after_send;
896 rs485->delay_rts_before_send = fixed_delay_rts_before_send;
897
898 if (rs485->flags & SER_RS485_ENABLED)
899 priv->mdr3 |= UART_OMAP_MDR3_DIR_EN;
900 else
901 priv->mdr3 &= ~UART_OMAP_MDR3_DIR_EN;
902
903 /*
904 * Retain same polarity semantics as RS485 software emulation,
905 * i.e. SER_RS485_RTS_ON_SEND means driving RTS low on send.
906 */
907 if (rs485->flags & SER_RS485_RTS_ON_SEND)
908 priv->mdr3 &= ~UART_OMAP_MDR3_DIR_POL;
909 else
910 priv->mdr3 |= UART_OMAP_MDR3_DIR_POL;
911
912 serial_out(up, UART_OMAP_MDR3, priv->mdr3);
913
914 return 0;
915 }
916
917 #ifdef CONFIG_SERIAL_8250_DMA
918 static int omap_8250_rx_dma(struct uart_8250_port *p);
919
920 /* Must be called while priv->rx_dma_lock is held */
__dma_rx_do_complete(struct uart_8250_port * p)921 static void __dma_rx_do_complete(struct uart_8250_port *p)
922 {
923 struct uart_8250_dma *dma = p->dma;
924 struct tty_port *tty_port = &p->port.state->port;
925 struct omap8250_priv *priv = p->port.private_data;
926 struct dma_chan *rxchan = dma->rxchan;
927 dma_cookie_t cookie;
928 struct dma_tx_state state;
929 int count;
930 int ret;
931 u32 reg;
932
933 if (!dma->rx_running)
934 goto out;
935
936 cookie = dma->rx_cookie;
937 dma->rx_running = 0;
938
939 /* Re-enable RX FIFO interrupt now that transfer is complete */
940 if (priv->habit & UART_HAS_RHR_IT_DIS) {
941 reg = serial_in(p, UART_OMAP_IER2);
942 reg &= ~UART_OMAP_IER2_RHR_IT_DIS;
943 serial_out(p, UART_OMAP_IER2, reg);
944 }
945
946 dmaengine_tx_status(rxchan, cookie, &state);
947
948 count = dma->rx_size - state.residue + state.in_flight_bytes;
949 if (count < dma->rx_size) {
950 dmaengine_terminate_async(rxchan);
951
952 /*
953 * Poll for teardown to complete which guarantees in
954 * flight data is drained.
955 */
956 if (state.in_flight_bytes) {
957 int poll_count = 25;
958
959 while (dmaengine_tx_status(rxchan, cookie, NULL) &&
960 poll_count--)
961 cpu_relax();
962
963 if (poll_count == -1)
964 dev_err(p->port.dev, "teardown incomplete\n");
965 }
966 }
967 if (!count)
968 goto out;
969 ret = tty_insert_flip_string(tty_port, dma->rx_buf, count);
970
971 p->port.icount.rx += ret;
972 p->port.icount.buf_overrun += count - ret;
973 out:
974
975 tty_flip_buffer_push(tty_port);
976 }
977
__dma_rx_complete(void * param)978 static void __dma_rx_complete(void *param)
979 {
980 struct uart_8250_port *p = param;
981 struct omap8250_priv *priv = p->port.private_data;
982 struct uart_8250_dma *dma = p->dma;
983 struct dma_tx_state state;
984 unsigned long flags;
985
986 /* Synchronize UART_IER access against the console. */
987 uart_port_lock_irqsave(&p->port, &flags);
988
989 /*
990 * If the tx status is not DMA_COMPLETE, then this is a delayed
991 * completion callback. A previous RX timeout flush would have
992 * already pushed the data, so exit.
993 */
994 if (dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state) !=
995 DMA_COMPLETE) {
996 uart_port_unlock_irqrestore(&p->port, flags);
997 return;
998 }
999 __dma_rx_do_complete(p);
1000 if (!priv->throttled) {
1001 p->ier |= UART_IER_RLSI | UART_IER_RDI;
1002 serial_out(p, UART_IER, p->ier);
1003 if (!(priv->habit & UART_HAS_EFR2))
1004 omap_8250_rx_dma(p);
1005 }
1006
1007 uart_port_unlock_irqrestore(&p->port, flags);
1008 }
1009
omap_8250_rx_dma_flush(struct uart_8250_port * p)1010 static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
1011 {
1012 struct omap8250_priv *priv = p->port.private_data;
1013 struct uart_8250_dma *dma = p->dma;
1014 struct dma_tx_state state;
1015 unsigned long flags;
1016 int ret;
1017
1018 spin_lock_irqsave(&priv->rx_dma_lock, flags);
1019
1020 if (!dma->rx_running) {
1021 spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
1022 return;
1023 }
1024
1025 ret = dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
1026 if (ret == DMA_IN_PROGRESS) {
1027 ret = dmaengine_pause(dma->rxchan);
1028 if (WARN_ON_ONCE(ret))
1029 priv->rx_dma_broken = true;
1030 }
1031 __dma_rx_do_complete(p);
1032 spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
1033 }
1034
omap_8250_rx_dma(struct uart_8250_port * p)1035 static int omap_8250_rx_dma(struct uart_8250_port *p)
1036 {
1037 struct omap8250_priv *priv = p->port.private_data;
1038 struct uart_8250_dma *dma = p->dma;
1039 int err = 0;
1040 struct dma_async_tx_descriptor *desc;
1041 unsigned long flags;
1042 u32 reg;
1043
1044 /* Port locked to synchronize UART_IER access against the console. */
1045 lockdep_assert_held_once(&p->port.lock);
1046
1047 if (priv->rx_dma_broken)
1048 return -EINVAL;
1049
1050 spin_lock_irqsave(&priv->rx_dma_lock, flags);
1051
1052 if (dma->rx_running) {
1053 enum dma_status state;
1054
1055 state = dmaengine_tx_status(dma->rxchan, dma->rx_cookie, NULL);
1056 if (state == DMA_COMPLETE) {
1057 /*
1058 * Disable RX interrupts to allow RX DMA completion
1059 * callback to run.
1060 */
1061 p->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
1062 serial_out(p, UART_IER, p->ier);
1063 }
1064 goto out;
1065 }
1066
1067 desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
1068 dma->rx_size, DMA_DEV_TO_MEM,
1069 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1070 if (!desc) {
1071 err = -EBUSY;
1072 goto out;
1073 }
1074
1075 dma->rx_running = 1;
1076 desc->callback = __dma_rx_complete;
1077 desc->callback_param = p;
1078
1079 dma->rx_cookie = dmaengine_submit(desc);
1080
1081 /*
1082 * Disable RX FIFO interrupt while RX DMA is enabled, else
1083 * spurious interrupt may be raised when data is in the RX FIFO
1084 * but is yet to be drained by DMA.
1085 */
1086 if (priv->habit & UART_HAS_RHR_IT_DIS) {
1087 reg = serial_in(p, UART_OMAP_IER2);
1088 reg |= UART_OMAP_IER2_RHR_IT_DIS;
1089 serial_out(p, UART_OMAP_IER2, reg);
1090 }
1091
1092 dma_async_issue_pending(dma->rxchan);
1093 out:
1094 spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
1095 return err;
1096 }
1097
1098 static int omap_8250_tx_dma(struct uart_8250_port *p);
1099
omap_8250_dma_tx_complete(void * param)1100 static void omap_8250_dma_tx_complete(void *param)
1101 {
1102 struct uart_8250_port *p = param;
1103 struct uart_8250_dma *dma = p->dma;
1104 struct tty_port *tport = &p->port.state->port;
1105 unsigned long flags;
1106 bool en_thri = false;
1107 struct omap8250_priv *priv = p->port.private_data;
1108
1109 dma_sync_single_for_cpu(dma->txchan->device->dev, dma->tx_addr,
1110 UART_XMIT_SIZE, DMA_TO_DEVICE);
1111
1112 uart_port_lock_irqsave(&p->port, &flags);
1113
1114 dma->tx_running = 0;
1115
1116 uart_xmit_advance(&p->port, dma->tx_size);
1117
1118 if (priv->delayed_restore) {
1119 priv->delayed_restore = 0;
1120 omap8250_restore_regs(p);
1121 }
1122
1123 if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS)
1124 uart_write_wakeup(&p->port);
1125
1126 if (!kfifo_is_empty(&tport->xmit_fifo) && !uart_tx_stopped(&p->port)) {
1127 int ret;
1128
1129 ret = omap_8250_tx_dma(p);
1130 if (ret)
1131 en_thri = true;
1132 } else if (p->capabilities & UART_CAP_RPM) {
1133 en_thri = true;
1134 }
1135
1136 if (en_thri) {
1137 dma->tx_err = 1;
1138 serial8250_set_THRI(p);
1139 }
1140
1141 uart_port_unlock_irqrestore(&p->port, flags);
1142 }
1143
omap_8250_tx_dma(struct uart_8250_port * p)1144 static int omap_8250_tx_dma(struct uart_8250_port *p)
1145 {
1146 struct uart_8250_dma *dma = p->dma;
1147 struct omap8250_priv *priv = p->port.private_data;
1148 struct tty_port *tport = &p->port.state->port;
1149 struct dma_async_tx_descriptor *desc;
1150 struct scatterlist sg;
1151 int skip_byte = -1;
1152 int ret;
1153
1154 if (dma->tx_running)
1155 return 0;
1156 if (uart_tx_stopped(&p->port) || kfifo_is_empty(&tport->xmit_fifo)) {
1157
1158 /*
1159 * Even if no data, we need to return an error for the two cases
1160 * below so serial8250_tx_chars() is invoked and properly clears
1161 * THRI and/or runtime suspend.
1162 */
1163 if (dma->tx_err || p->capabilities & UART_CAP_RPM) {
1164 ret = -EBUSY;
1165 goto err;
1166 }
1167 serial8250_clear_THRI(p);
1168 return 0;
1169 }
1170
1171 sg_init_table(&sg, 1);
1172 ret = kfifo_dma_out_prepare_mapped(&tport->xmit_fifo, &sg, 1,
1173 UART_XMIT_SIZE, dma->tx_addr);
1174 if (ret != 1) {
1175 serial8250_clear_THRI(p);
1176 return 0;
1177 }
1178
1179 dma->tx_size = sg_dma_len(&sg);
1180
1181 if (priv->habit & OMAP_DMA_TX_KICK) {
1182 unsigned char c;
1183 u8 tx_lvl;
1184
1185 /*
1186 * We need to put the first byte into the FIFO in order to start
1187 * the DMA transfer. For transfers smaller than four bytes we
1188 * don't bother doing DMA at all. It seem not matter if there
1189 * are still bytes in the FIFO from the last transfer (in case
1190 * we got here directly from omap_8250_dma_tx_complete()). Bytes
1191 * leaving the FIFO seem not to trigger the DMA transfer. It is
1192 * really the byte that we put into the FIFO.
1193 * If the FIFO is already full then we most likely got here from
1194 * omap_8250_dma_tx_complete(). And this means the DMA engine
1195 * just completed its work. We don't have to wait the complete
1196 * 86us at 115200,8n1 but around 60us (not to mention lower
1197 * baudrates). So in that case we take the interrupt and try
1198 * again with an empty FIFO.
1199 */
1200 tx_lvl = serial_in(p, UART_OMAP_TX_LVL);
1201 if (tx_lvl == p->tx_loadsz) {
1202 ret = -EBUSY;
1203 goto err;
1204 }
1205 if (dma->tx_size < 4) {
1206 ret = -EINVAL;
1207 goto err;
1208 }
1209 if (!kfifo_get(&tport->xmit_fifo, &c)) {
1210 ret = -EINVAL;
1211 goto err;
1212 }
1213 skip_byte = c;
1214 /* now we need to recompute due to kfifo_get */
1215 kfifo_dma_out_prepare_mapped(&tport->xmit_fifo, &sg, 1,
1216 UART_XMIT_SIZE, dma->tx_addr);
1217 }
1218
1219 desc = dmaengine_prep_slave_sg(dma->txchan, &sg, 1, DMA_MEM_TO_DEV,
1220 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1221 if (!desc) {
1222 ret = -EBUSY;
1223 goto err;
1224 }
1225
1226 dma->tx_running = 1;
1227
1228 desc->callback = omap_8250_dma_tx_complete;
1229 desc->callback_param = p;
1230
1231 dma->tx_cookie = dmaengine_submit(desc);
1232
1233 dma_sync_single_for_device(dma->txchan->device->dev, dma->tx_addr,
1234 UART_XMIT_SIZE, DMA_TO_DEVICE);
1235
1236 dma_async_issue_pending(dma->txchan);
1237 if (dma->tx_err)
1238 dma->tx_err = 0;
1239
1240 serial8250_clear_THRI(p);
1241 ret = 0;
1242 goto out_skip;
1243 err:
1244 dma->tx_err = 1;
1245 out_skip:
1246 if (skip_byte >= 0)
1247 serial_out(p, UART_TX, skip_byte);
1248 return ret;
1249 }
1250
handle_rx_dma(struct uart_8250_port * up,unsigned int iir)1251 static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
1252 {
1253 switch (iir & 0x3f) {
1254 case UART_IIR_RLSI:
1255 case UART_IIR_RX_TIMEOUT:
1256 case UART_IIR_RDI:
1257 omap_8250_rx_dma_flush(up);
1258 return true;
1259 }
1260 return omap_8250_rx_dma(up);
1261 }
1262
omap_8250_handle_rx_dma(struct uart_8250_port * up,u8 iir,u16 status)1263 static u16 omap_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir, u16 status)
1264 {
1265 if ((status & (UART_LSR_DR | UART_LSR_BI)) &&
1266 (iir & UART_IIR_RDI)) {
1267 if (handle_rx_dma(up, iir)) {
1268 status = serial8250_rx_chars(up, status);
1269 omap_8250_rx_dma(up);
1270 }
1271 }
1272
1273 return status;
1274 }
1275
am654_8250_handle_rx_dma(struct uart_8250_port * up,u8 iir,u16 status)1276 static void am654_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir,
1277 u16 status)
1278 {
1279 /* Port locked to synchronize UART_IER access against the console. */
1280 lockdep_assert_held_once(&up->port.lock);
1281
1282 /*
1283 * Queue a new transfer if FIFO has data.
1284 */
1285 if ((status & (UART_LSR_DR | UART_LSR_BI)) &&
1286 (up->ier & UART_IER_RDI)) {
1287 omap_8250_rx_dma(up);
1288 serial_out(up, UART_OMAP_EFR2, UART_OMAP_EFR2_TIMEOUT_BEHAVE);
1289 } else if ((iir & 0x3f) == UART_IIR_RX_TIMEOUT) {
1290 /*
1291 * Disable RX timeout, read IIR to clear
1292 * current timeout condition, clear EFR2 to
1293 * periodic timeouts, re-enable interrupts.
1294 */
1295 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
1296 serial_out(up, UART_IER, up->ier);
1297 omap_8250_rx_dma_flush(up);
1298 serial_in(up, UART_IIR);
1299 serial_out(up, UART_OMAP_EFR2, 0x0);
1300 up->ier |= UART_IER_RLSI | UART_IER_RDI;
1301 serial_out(up, UART_IER, up->ier);
1302 }
1303 }
1304
1305 /*
1306 * This is mostly serial8250_handle_irq(). We have a slightly different DMA
1307 * hoook for RX/TX and need different logic for them in the ISR. Therefore we
1308 * use the default routine in the non-DMA case and this one for with DMA.
1309 */
omap_8250_dma_handle_irq(struct uart_port * port)1310 static int omap_8250_dma_handle_irq(struct uart_port *port)
1311 {
1312 struct uart_8250_port *up = up_to_u8250p(port);
1313 struct omap8250_priv *priv = up->port.private_data;
1314 u16 status;
1315 u8 iir;
1316
1317 iir = serial_port_in(port, UART_IIR);
1318 if (iir & UART_IIR_NO_INT) {
1319 return IRQ_HANDLED;
1320 }
1321
1322 uart_port_lock(port);
1323
1324 status = serial_port_in(port, UART_LSR);
1325
1326 if ((iir & 0x3f) != UART_IIR_THRI) {
1327 if (priv->habit & UART_HAS_EFR2)
1328 am654_8250_handle_rx_dma(up, iir, status);
1329 else
1330 status = omap_8250_handle_rx_dma(up, iir, status);
1331 }
1332
1333 serial8250_modem_status(up);
1334 if (status & UART_LSR_THRE && up->dma->tx_err) {
1335 if (uart_tx_stopped(&up->port) ||
1336 kfifo_is_empty(&up->port.state->port.xmit_fifo)) {
1337 up->dma->tx_err = 0;
1338 serial8250_tx_chars(up);
1339 } else {
1340 /*
1341 * try again due to an earlier failer which
1342 * might have been resolved by now.
1343 */
1344 if (omap_8250_tx_dma(up))
1345 serial8250_tx_chars(up);
1346 }
1347 }
1348
1349 uart_unlock_and_check_sysrq(port);
1350
1351 return 1;
1352 }
1353
the_no_dma_filter_fn(struct dma_chan * chan,void * param)1354 static bool the_no_dma_filter_fn(struct dma_chan *chan, void *param)
1355 {
1356 return false;
1357 }
1358
1359 #else
1360
omap_8250_rx_dma(struct uart_8250_port * p)1361 static inline int omap_8250_rx_dma(struct uart_8250_port *p)
1362 {
1363 return -EINVAL;
1364 }
1365 #endif
1366
omap8250_no_handle_irq(struct uart_port * port)1367 static int omap8250_no_handle_irq(struct uart_port *port)
1368 {
1369 /* IRQ has not been requested but handling irq? */
1370 WARN_ONCE(1, "Unexpected irq handling before port startup\n");
1371 return 0;
1372 }
1373
1374 static struct omap8250_dma_params am654_dma = {
1375 .rx_size = SZ_2K,
1376 .rx_trigger = 1,
1377 .tx_trigger = TX_TRIGGER,
1378 };
1379
1380 static struct omap8250_dma_params am33xx_dma = {
1381 .rx_size = RX_TRIGGER,
1382 .rx_trigger = RX_TRIGGER,
1383 .tx_trigger = TX_TRIGGER,
1384 };
1385
1386 static struct omap8250_platdata am654_platdata = {
1387 .dma_params = &am654_dma,
1388 .habit = UART_HAS_EFR2 | UART_HAS_RHR_IT_DIS |
1389 UART_RX_TIMEOUT_QUIRK | UART_HAS_NATIVE_RS485,
1390 };
1391
1392 static struct omap8250_platdata am33xx_platdata = {
1393 .dma_params = &am33xx_dma,
1394 .habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE,
1395 };
1396
1397 static struct omap8250_platdata omap4_platdata = {
1398 .dma_params = &am33xx_dma,
1399 .habit = UART_ERRATA_CLOCK_DISABLE,
1400 };
1401
1402 static const struct of_device_id omap8250_dt_ids[] = {
1403 { .compatible = "ti,am654-uart", .data = &am654_platdata, },
1404 { .compatible = "ti,omap2-uart" },
1405 { .compatible = "ti,omap3-uart" },
1406 { .compatible = "ti,omap4-uart", .data = &omap4_platdata, },
1407 { .compatible = "ti,am3352-uart", .data = &am33xx_platdata, },
1408 { .compatible = "ti,am4372-uart", .data = &am33xx_platdata, },
1409 { .compatible = "ti,dra742-uart", .data = &omap4_platdata, },
1410 {},
1411 };
1412 MODULE_DEVICE_TABLE(of, omap8250_dt_ids);
1413
omap8250_probe(struct platform_device * pdev)1414 static int omap8250_probe(struct platform_device *pdev)
1415 {
1416 struct device_node *np = pdev->dev.of_node;
1417 struct omap8250_priv *priv;
1418 const struct omap8250_platdata *pdata;
1419 struct uart_8250_port up;
1420 struct resource *regs;
1421 void __iomem *membase;
1422 int ret;
1423
1424 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1425 if (!regs) {
1426 dev_err(&pdev->dev, "missing registers\n");
1427 return -EINVAL;
1428 }
1429
1430 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
1431 if (!priv)
1432 return -ENOMEM;
1433
1434 membase = devm_ioremap(&pdev->dev, regs->start,
1435 resource_size(regs));
1436 if (!membase)
1437 return -ENODEV;
1438
1439 memset(&up, 0, sizeof(up));
1440 up.port.dev = &pdev->dev;
1441 up.port.mapbase = regs->start;
1442 up.port.membase = membase;
1443 /*
1444 * It claims to be 16C750 compatible however it is a little different.
1445 * It has EFR and has no FCR7_64byte bit. The AFE (which it claims to
1446 * have) is enabled via EFR instead of MCR. The type is set here 8250
1447 * just to get things going. UNKNOWN does not work for a few reasons and
1448 * we don't need our own type since we don't use 8250's set_termios()
1449 * or pm callback.
1450 */
1451 up.port.type = PORT_8250;
1452 up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SOFT_FLOW | UPF_HARD_FLOW;
1453 up.port.private_data = priv;
1454
1455 up.tx_loadsz = 64;
1456 up.capabilities = UART_CAP_FIFO;
1457 #ifdef CONFIG_PM
1458 /*
1459 * Runtime PM is mostly transparent. However to do it right we need to a
1460 * TX empty interrupt before we can put the device to auto idle. So if
1461 * PM is not enabled we don't add that flag and can spare that one extra
1462 * interrupt in the TX path.
1463 */
1464 up.capabilities |= UART_CAP_RPM;
1465 #endif
1466 up.port.set_termios = omap_8250_set_termios;
1467 up.port.set_mctrl = omap8250_set_mctrl;
1468 up.port.pm = omap_8250_pm;
1469 up.port.startup = omap_8250_startup;
1470 up.port.shutdown = omap_8250_shutdown;
1471 up.port.throttle = omap_8250_throttle;
1472 up.port.unthrottle = omap_8250_unthrottle;
1473 up.port.rs485_config = omap8250_rs485_config;
1474 /* same rs485_supported for software emulation and native RS485 */
1475 up.port.rs485_supported = serial8250_em485_supported;
1476 up.rs485_start_tx = serial8250_em485_start_tx;
1477 up.rs485_stop_tx = serial8250_em485_stop_tx;
1478 up.port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
1479
1480 ret = uart_read_port_properties(&up.port);
1481 if (ret)
1482 return ret;
1483
1484 up.port.regshift = OMAP_UART_REGSHIFT;
1485 up.port.fifosize = 64;
1486
1487 if (!up.port.uartclk) {
1488 struct clk *clk;
1489
1490 clk = devm_clk_get(&pdev->dev, NULL);
1491 if (IS_ERR(clk)) {
1492 if (PTR_ERR(clk) == -EPROBE_DEFER)
1493 return -EPROBE_DEFER;
1494 } else {
1495 up.port.uartclk = clk_get_rate(clk);
1496 }
1497 }
1498
1499 if (of_property_read_u32(np, "overrun-throttle-ms",
1500 &up.overrun_backoff_time_ms) != 0)
1501 up.overrun_backoff_time_ms = 0;
1502
1503 pdata = of_device_get_match_data(&pdev->dev);
1504 if (pdata)
1505 priv->habit |= pdata->habit;
1506
1507 if (!up.port.uartclk) {
1508 up.port.uartclk = DEFAULT_CLK_SPEED;
1509 dev_warn(&pdev->dev,
1510 "No clock speed specified: using default: %d\n",
1511 DEFAULT_CLK_SPEED);
1512 }
1513
1514 priv->membase = membase;
1515 priv->line = -ENODEV;
1516 priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
1517 priv->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
1518 cpu_latency_qos_add_request(&priv->pm_qos_request, priv->latency);
1519 INIT_WORK(&priv->qos_work, omap8250_uart_qos_work);
1520
1521 spin_lock_init(&priv->rx_dma_lock);
1522
1523 platform_set_drvdata(pdev, priv);
1524
1525 device_set_wakeup_capable(&pdev->dev, true);
1526 if (of_property_read_bool(np, "wakeup-source"))
1527 device_set_wakeup_enable(&pdev->dev, true);
1528
1529 pm_runtime_enable(&pdev->dev);
1530 pm_runtime_use_autosuspend(&pdev->dev);
1531
1532 /*
1533 * Disable runtime PM until autosuspend delay unless specifically
1534 * enabled by the user via sysfs. This is the historic way to
1535 * prevent an unsafe default policy with lossy characters on wake-up.
1536 * For serdev devices this is not needed, the policy can be managed by
1537 * the serdev driver.
1538 */
1539 if (!of_get_available_child_count(pdev->dev.of_node))
1540 pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
1541
1542 pm_runtime_get_sync(&pdev->dev);
1543
1544 omap_serial_fill_features_erratas(&up, priv);
1545 up.port.handle_irq = omap8250_no_handle_irq;
1546 priv->rx_trigger = RX_TRIGGER;
1547 priv->tx_trigger = TX_TRIGGER;
1548 #ifdef CONFIG_SERIAL_8250_DMA
1549 /*
1550 * Oh DMA support. If there are no DMA properties in the DT then
1551 * we will fall back to a generic DMA channel which does not
1552 * really work here. To ensure that we do not get a generic DMA
1553 * channel assigned, we have the the_no_dma_filter_fn() here.
1554 * To avoid "failed to request DMA" messages we check for DMA
1555 * properties in DT.
1556 */
1557 ret = of_property_count_strings(np, "dma-names");
1558 if (ret == 2) {
1559 struct omap8250_dma_params *dma_params = NULL;
1560 struct uart_8250_dma *dma = &priv->omap8250_dma;
1561
1562 dma->fn = the_no_dma_filter_fn;
1563 dma->tx_dma = omap_8250_tx_dma;
1564 dma->rx_dma = omap_8250_rx_dma;
1565 if (pdata)
1566 dma_params = pdata->dma_params;
1567
1568 if (dma_params) {
1569 dma->rx_size = dma_params->rx_size;
1570 dma->rxconf.src_maxburst = dma_params->rx_trigger;
1571 dma->txconf.dst_maxburst = dma_params->tx_trigger;
1572 priv->rx_trigger = dma_params->rx_trigger;
1573 priv->tx_trigger = dma_params->tx_trigger;
1574 } else {
1575 dma->rx_size = RX_TRIGGER;
1576 dma->rxconf.src_maxburst = RX_TRIGGER;
1577 dma->txconf.dst_maxburst = TX_TRIGGER;
1578 }
1579 }
1580 #endif
1581
1582 irq_set_status_flags(up.port.irq, IRQ_NOAUTOEN);
1583 ret = devm_request_irq(&pdev->dev, up.port.irq, omap8250_irq, 0,
1584 dev_name(&pdev->dev), priv);
1585 if (ret < 0)
1586 goto err;
1587
1588 priv->wakeirq = irq_of_parse_and_map(np, 1);
1589
1590 ret = serial8250_register_8250_port(&up);
1591 if (ret < 0) {
1592 dev_err(&pdev->dev, "unable to register 8250 port\n");
1593 goto err;
1594 }
1595 priv->line = ret;
1596 pm_runtime_mark_last_busy(&pdev->dev);
1597 pm_runtime_put_autosuspend(&pdev->dev);
1598 return 0;
1599 err:
1600 pm_runtime_dont_use_autosuspend(&pdev->dev);
1601 pm_runtime_put_sync(&pdev->dev);
1602 flush_work(&priv->qos_work);
1603 pm_runtime_disable(&pdev->dev);
1604 cpu_latency_qos_remove_request(&priv->pm_qos_request);
1605 return ret;
1606 }
1607
omap8250_remove(struct platform_device * pdev)1608 static void omap8250_remove(struct platform_device *pdev)
1609 {
1610 struct omap8250_priv *priv = platform_get_drvdata(pdev);
1611 struct uart_8250_port *up;
1612 int err;
1613
1614 err = pm_runtime_resume_and_get(&pdev->dev);
1615 if (err)
1616 dev_err(&pdev->dev, "Failed to resume hardware\n");
1617
1618 up = serial8250_get_port(priv->line);
1619 omap_8250_shutdown(&up->port);
1620 serial8250_unregister_port(priv->line);
1621 priv->line = -ENODEV;
1622 pm_runtime_dont_use_autosuspend(&pdev->dev);
1623 pm_runtime_put_sync(&pdev->dev);
1624 flush_work(&priv->qos_work);
1625 pm_runtime_disable(&pdev->dev);
1626 cpu_latency_qos_remove_request(&priv->pm_qos_request);
1627 device_set_wakeup_capable(&pdev->dev, false);
1628 }
1629
omap8250_prepare(struct device * dev)1630 static int omap8250_prepare(struct device *dev)
1631 {
1632 struct omap8250_priv *priv = dev_get_drvdata(dev);
1633
1634 if (!priv)
1635 return 0;
1636 priv->is_suspending = true;
1637 return 0;
1638 }
1639
omap8250_complete(struct device * dev)1640 static void omap8250_complete(struct device *dev)
1641 {
1642 struct omap8250_priv *priv = dev_get_drvdata(dev);
1643
1644 if (!priv)
1645 return;
1646 priv->is_suspending = false;
1647 }
1648
omap8250_suspend(struct device * dev)1649 static int omap8250_suspend(struct device *dev)
1650 {
1651 struct omap8250_priv *priv = dev_get_drvdata(dev);
1652 struct uart_8250_port *up = serial8250_get_port(priv->line);
1653 int err = 0;
1654
1655 serial8250_suspend_port(priv->line);
1656
1657 err = pm_runtime_resume_and_get(dev);
1658 if (err)
1659 return err;
1660 if (!device_may_wakeup(dev))
1661 priv->wer = 0;
1662 serial_out(up, UART_OMAP_WER, priv->wer);
1663 if (uart_console(&up->port) && console_suspend_enabled)
1664 err = pm_runtime_force_suspend(dev);
1665 flush_work(&priv->qos_work);
1666
1667 return err;
1668 }
1669
omap8250_resume(struct device * dev)1670 static int omap8250_resume(struct device *dev)
1671 {
1672 struct omap8250_priv *priv = dev_get_drvdata(dev);
1673 struct uart_8250_port *up = serial8250_get_port(priv->line);
1674 int err;
1675
1676 if (uart_console(&up->port) && console_suspend_enabled) {
1677 err = pm_runtime_force_resume(dev);
1678 if (err)
1679 return err;
1680 }
1681
1682 serial8250_resume_port(priv->line);
1683 /* Paired with pm_runtime_resume_and_get() in omap8250_suspend() */
1684 pm_runtime_mark_last_busy(dev);
1685 pm_runtime_put_autosuspend(dev);
1686
1687 return 0;
1688 }
1689
omap8250_lost_context(struct uart_8250_port * up)1690 static int omap8250_lost_context(struct uart_8250_port *up)
1691 {
1692 u32 val;
1693
1694 val = serial_in(up, UART_OMAP_SCR);
1695 /*
1696 * If we lose context, then SCR is set to its reset value of zero.
1697 * After set_termios() we set bit 3 of SCR (TX_EMPTY_CTL_IT) to 1,
1698 * among other bits, to never set the register back to zero again.
1699 */
1700 if (!val)
1701 return 1;
1702 return 0;
1703 }
1704
uart_write(struct omap8250_priv * priv,u32 reg,u32 val)1705 static void uart_write(struct omap8250_priv *priv, u32 reg, u32 val)
1706 {
1707 writel(val, priv->membase + (reg << OMAP_UART_REGSHIFT));
1708 }
1709
1710 /* TODO: in future, this should happen via API in drivers/reset/ */
omap8250_soft_reset(struct device * dev)1711 static int omap8250_soft_reset(struct device *dev)
1712 {
1713 struct omap8250_priv *priv = dev_get_drvdata(dev);
1714 int timeout = 100;
1715 int sysc;
1716 int syss;
1717
1718 /*
1719 * At least on omap4, unused uarts may not idle after reset without
1720 * a basic scr dma configuration even with no dma in use. The
1721 * module clkctrl status bits will be 1 instead of 3 blocking idle
1722 * for the whole clockdomain. The softreset below will clear scr,
1723 * and we restore it on resume so this is safe to do on all SoCs
1724 * needing omap8250_soft_reset() quirk. Do it in two writes as
1725 * recommended in the comment for omap8250_update_scr().
1726 */
1727 uart_write(priv, UART_OMAP_SCR, OMAP_UART_SCR_DMAMODE_1);
1728 uart_write(priv, UART_OMAP_SCR,
1729 OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL);
1730
1731 sysc = uart_read(priv, UART_OMAP_SYSC);
1732
1733 /* softreset the UART */
1734 sysc |= OMAP_UART_SYSC_SOFTRESET;
1735 uart_write(priv, UART_OMAP_SYSC, sysc);
1736
1737 /* By experiments, 1us enough for reset complete on AM335x */
1738 do {
1739 udelay(1);
1740 syss = uart_read(priv, UART_OMAP_SYSS);
1741 } while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE));
1742
1743 if (!timeout) {
1744 dev_err(dev, "timed out waiting for reset done\n");
1745 return -ETIMEDOUT;
1746 }
1747
1748 return 0;
1749 }
1750
omap8250_runtime_suspend(struct device * dev)1751 static int omap8250_runtime_suspend(struct device *dev)
1752 {
1753 struct omap8250_priv *priv = dev_get_drvdata(dev);
1754 struct uart_8250_port *up = NULL;
1755
1756 if (priv->line >= 0)
1757 up = serial8250_get_port(priv->line);
1758
1759 if (priv->habit & UART_ERRATA_CLOCK_DISABLE) {
1760 int ret;
1761
1762 ret = omap8250_soft_reset(dev);
1763 if (ret)
1764 return ret;
1765
1766 if (up) {
1767 /* Restore to UART mode after reset (for wakeup) */
1768 omap8250_update_mdr1(up, priv);
1769 /* Restore wakeup enable register */
1770 serial_out(up, UART_OMAP_WER, priv->wer);
1771 }
1772 }
1773
1774 if (up && up->dma && up->dma->rxchan)
1775 omap_8250_rx_dma_flush(up);
1776
1777 priv->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
1778 schedule_work(&priv->qos_work);
1779 atomic_set(&priv->active, 0);
1780
1781 return 0;
1782 }
1783
omap8250_runtime_resume(struct device * dev)1784 static int omap8250_runtime_resume(struct device *dev)
1785 {
1786 struct omap8250_priv *priv = dev_get_drvdata(dev);
1787 struct uart_8250_port *up = NULL;
1788
1789 /* Did the hardware wake to a device IO interrupt before a wakeirq? */
1790 if (atomic_read(&priv->active))
1791 return 0;
1792
1793 if (priv->line >= 0)
1794 up = serial8250_get_port(priv->line);
1795
1796 if (up && omap8250_lost_context(up)) {
1797 uart_port_lock_irq(&up->port);
1798 omap8250_restore_regs(up);
1799 uart_port_unlock_irq(&up->port);
1800 }
1801
1802 if (up && up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2)) {
1803 uart_port_lock_irq(&up->port);
1804 omap_8250_rx_dma(up);
1805 uart_port_unlock_irq(&up->port);
1806 }
1807
1808 atomic_set(&priv->active, 1);
1809 priv->latency = priv->calc_latency;
1810 schedule_work(&priv->qos_work);
1811
1812 return 0;
1813 }
1814
1815 #ifdef CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP
omap8250_console_fixup(void)1816 static int __init omap8250_console_fixup(void)
1817 {
1818 char *omap_str;
1819 char *options;
1820 u8 idx;
1821
1822 if (strstr(boot_command_line, "console=ttyS"))
1823 /* user set a ttyS based name for the console */
1824 return 0;
1825
1826 omap_str = strstr(boot_command_line, "console=ttyO");
1827 if (!omap_str)
1828 /* user did not set ttyO based console, so we don't care */
1829 return 0;
1830
1831 omap_str += 12;
1832 if ('0' <= *omap_str && *omap_str <= '9')
1833 idx = *omap_str - '0';
1834 else
1835 return 0;
1836
1837 omap_str++;
1838 if (omap_str[0] == ',') {
1839 omap_str++;
1840 options = omap_str;
1841 } else {
1842 options = NULL;
1843 }
1844
1845 add_preferred_console("ttyS", idx, options);
1846 pr_err("WARNING: Your 'console=ttyO%d' has been replaced by 'ttyS%d'\n",
1847 idx, idx);
1848 pr_err("This ensures that you still see kernel messages. Please\n");
1849 pr_err("update your kernel commandline.\n");
1850 return 0;
1851 }
1852 console_initcall(omap8250_console_fixup);
1853 #endif
1854
1855 static const struct dev_pm_ops omap8250_dev_pm_ops = {
1856 SYSTEM_SLEEP_PM_OPS(omap8250_suspend, omap8250_resume)
1857 RUNTIME_PM_OPS(omap8250_runtime_suspend,
1858 omap8250_runtime_resume, NULL)
1859 .prepare = pm_sleep_ptr(omap8250_prepare),
1860 .complete = pm_sleep_ptr(omap8250_complete),
1861 };
1862
1863 static struct platform_driver omap8250_platform_driver = {
1864 .driver = {
1865 .name = "omap8250",
1866 .pm = pm_ptr(&omap8250_dev_pm_ops),
1867 .of_match_table = omap8250_dt_ids,
1868 },
1869 .probe = omap8250_probe,
1870 .remove_new = omap8250_remove,
1871 };
1872 module_platform_driver(omap8250_platform_driver);
1873
1874 MODULE_AUTHOR("Sebastian Andrzej Siewior");
1875 MODULE_DESCRIPTION("OMAP 8250 Driver");
1876 MODULE_LICENSE("GPL v2");
1877