1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (C) 2018 Marvell
4 *
5 * Authors:
6 * Evan Wang <xswang@marvell.com>
7 * Miquèl Raynal <miquel.raynal@bootlin.com>
8 * Pali Rohár <pali@kernel.org>
9 * Marek Behún <kabel@kernel.org>
10 *
11 * Structure inspired from phy-mvebu-cp110-comphy.c written by Antoine Tenart.
12 * Comphy code from ARM Trusted Firmware ported by Pali Rohár <pali@kernel.org>
13 * and Marek Behún <kabel@kernel.org>.
14 */
15
16 #include <linux/bitfield.h>
17 #include <linux/clk.h>
18 #include <linux/io.h>
19 #include <linux/iopoll.h>
20 #include <linux/mfd/syscon.h>
21 #include <linux/module.h>
22 #include <linux/of.h>
23 #include <linux/phy.h>
24 #include <linux/phy/phy.h>
25 #include <linux/platform_device.h>
26 #include <linux/spinlock.h>
27
28 #define PLL_SET_DELAY_US 600
29 #define COMPHY_PLL_SLEEP 1000
30 #define COMPHY_PLL_TIMEOUT 150000
31
32 /* Comphy lane2 indirect access register offset */
33 #define COMPHY_LANE2_INDIR_ADDR 0x0
34 #define COMPHY_LANE2_INDIR_DATA 0x4
35
36 /* SATA and USB3 PHY offset compared to SATA PHY */
37 #define COMPHY_LANE2_REGS_BASE 0x200
38
39 /*
40 * When accessing common PHY lane registers directly, we need to shift by 1,
41 * since the registers are 16-bit.
42 */
43 #define COMPHY_LANE_REG_DIRECT(reg) (((reg) & 0x7FF) << 1)
44
45 /* COMPHY registers */
46 #define COMPHY_POWER_PLL_CTRL 0x01
47 #define PU_IVREF_BIT BIT(15)
48 #define PU_PLL_BIT BIT(14)
49 #define PU_RX_BIT BIT(13)
50 #define PU_TX_BIT BIT(12)
51 #define PU_TX_INTP_BIT BIT(11)
52 #define PU_DFE_BIT BIT(10)
53 #define RESET_DTL_RX_BIT BIT(9)
54 #define PLL_LOCK_BIT BIT(8)
55 #define REF_FREF_SEL_MASK GENMASK(4, 0)
56 #define REF_FREF_SEL_SERDES_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x1)
57 #define REF_FREF_SEL_SERDES_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
58 #define REF_FREF_SEL_SERDES_50MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x4)
59 #define REF_FREF_SEL_PCIE_USB3_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x2)
60 #define REF_FREF_SEL_PCIE_USB3_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
61 #define COMPHY_MODE_MASK GENMASK(7, 5)
62 #define COMPHY_MODE_SATA FIELD_PREP(COMPHY_MODE_MASK, 0x0)
63 #define COMPHY_MODE_PCIE FIELD_PREP(COMPHY_MODE_MASK, 0x3)
64 #define COMPHY_MODE_SERDES FIELD_PREP(COMPHY_MODE_MASK, 0x4)
65 #define COMPHY_MODE_USB3 FIELD_PREP(COMPHY_MODE_MASK, 0x5)
66
67 #define COMPHY_KVCO_CAL_CTRL 0x02
68 #define USE_MAX_PLL_RATE_BIT BIT(12)
69 #define SPEED_PLL_MASK GENMASK(7, 2)
70 #define SPEED_PLL_VALUE_16 FIELD_PREP(SPEED_PLL_MASK, 0x10)
71
72 #define COMPHY_DIG_LOOPBACK_EN 0x23
73 #define SEL_DATA_WIDTH_MASK GENMASK(11, 10)
74 #define DATA_WIDTH_10BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x0)
75 #define DATA_WIDTH_20BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x1)
76 #define DATA_WIDTH_40BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x2)
77 #define PLL_READY_TX_BIT BIT(4)
78
79 #define COMPHY_SYNC_PATTERN 0x24
80 #define TXD_INVERT_BIT BIT(10)
81 #define RXD_INVERT_BIT BIT(11)
82
83 #define COMPHY_SYNC_MASK_GEN 0x25
84 #define PHY_GEN_MAX_MASK GENMASK(11, 10)
85 #define PHY_GEN_MAX_USB3_5G FIELD_PREP(PHY_GEN_MAX_MASK, 0x1)
86
87 #define COMPHY_ISOLATION_CTRL 0x26
88 #define PHY_ISOLATE_MODE BIT(15)
89
90 #define COMPHY_GEN2_SET2 0x3e
91 #define GS2_TX_SSC_AMP_MASK GENMASK(15, 9)
92 #define GS2_TX_SSC_AMP_4128 FIELD_PREP(GS2_TX_SSC_AMP_MASK, 0x20)
93 #define GS2_VREG_RXTX_MAS_ISET_MASK GENMASK(8, 7)
94 #define GS2_VREG_RXTX_MAS_ISET_60U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
95 0x0)
96 #define GS2_VREG_RXTX_MAS_ISET_80U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
97 0x1)
98 #define GS2_VREG_RXTX_MAS_ISET_100U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
99 0x2)
100 #define GS2_VREG_RXTX_MAS_ISET_120U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
101 0x3)
102 #define GS2_RSVD_6_0_MASK GENMASK(6, 0)
103
104 #define COMPHY_GEN3_SET2 0x3f
105
106 #define COMPHY_IDLE_SYNC_EN 0x48
107 #define IDLE_SYNC_EN BIT(12)
108
109 #define COMPHY_MISC_CTRL0 0x4F
110 #define CLK100M_125M_EN BIT(4)
111 #define TXDCLK_2X_SEL BIT(6)
112 #define CLK500M_EN BIT(7)
113 #define PHY_REF_CLK_SEL BIT(10)
114
115 #define COMPHY_SFT_RESET 0x52
116 #define SFT_RST BIT(9)
117 #define SFT_RST_NO_REG BIT(10)
118
119 #define COMPHY_MISC_CTRL1 0x73
120 #define SEL_BITS_PCIE_FORCE BIT(15)
121
122 #define COMPHY_GEN2_SET3 0x112
123 #define GS3_FFE_CAP_SEL_MASK GENMASK(3, 0)
124 #define GS3_FFE_CAP_SEL_VALUE FIELD_PREP(GS3_FFE_CAP_SEL_MASK, 0xF)
125
126 /* PIPE registers */
127 #define COMPHY_PIPE_LANE_CFG0 0x180
128 #define PRD_TXDEEMPH0_MASK BIT(0)
129 #define PRD_TXMARGIN_MASK GENMASK(3, 1)
130 #define PRD_TXSWING_MASK BIT(4)
131 #define CFG_TX_ALIGN_POS_MASK GENMASK(8, 5)
132
133 #define COMPHY_PIPE_LANE_CFG1 0x181
134 #define PRD_TXDEEMPH1_MASK BIT(15)
135 #define USE_MAX_PLL_RATE_EN BIT(9)
136 #define TX_DET_RX_MODE BIT(6)
137 #define GEN2_TX_DATA_DLY_MASK GENMASK(4, 3)
138 #define GEN2_TX_DATA_DLY_DEFT FIELD_PREP(GEN2_TX_DATA_DLY_MASK, 2)
139 #define TX_ELEC_IDLE_MODE_EN BIT(0)
140
141 #define COMPHY_PIPE_LANE_STAT1 0x183
142 #define TXDCLK_PCLK_EN BIT(0)
143
144 #define COMPHY_PIPE_LANE_CFG4 0x188
145 #define SPREAD_SPECTRUM_CLK_EN BIT(7)
146
147 #define COMPHY_PIPE_RST_CLK_CTRL 0x1C1
148 #define PIPE_SOFT_RESET BIT(0)
149 #define PIPE_REG_RESET BIT(1)
150 #define MODE_CORE_CLK_FREQ_SEL BIT(9)
151 #define MODE_PIPE_WIDTH_32 BIT(3)
152 #define MODE_REFDIV_MASK GENMASK(5, 4)
153 #define MODE_REFDIV_BY_4 FIELD_PREP(MODE_REFDIV_MASK, 0x2)
154
155 #define COMPHY_PIPE_TEST_MODE_CTRL 0x1C2
156 #define MODE_MARGIN_OVERRIDE BIT(2)
157
158 #define COMPHY_PIPE_CLK_SRC_LO 0x1C3
159 #define MODE_CLK_SRC BIT(0)
160 #define BUNDLE_PERIOD_SEL BIT(1)
161 #define BUNDLE_PERIOD_SCALE_MASK GENMASK(3, 2)
162 #define BUNDLE_SAMPLE_CTRL BIT(4)
163 #define PLL_READY_DLY_MASK GENMASK(7, 5)
164 #define CFG_SEL_20B BIT(15)
165
166 #define COMPHY_PIPE_PWR_MGM_TIM1 0x1D0
167 #define CFG_PM_OSCCLK_WAIT_MASK GENMASK(15, 12)
168 #define CFG_PM_RXDEN_WAIT_MASK GENMASK(11, 8)
169 #define CFG_PM_RXDEN_WAIT_1_UNIT FIELD_PREP(CFG_PM_RXDEN_WAIT_MASK, 0x1)
170 #define CFG_PM_RXDLOZ_WAIT_MASK GENMASK(7, 0)
171 #define CFG_PM_RXDLOZ_WAIT_7_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0x7)
172 #define CFG_PM_RXDLOZ_WAIT_12_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0xC)
173
174 /*
175 * This register is not from PHY lane register space. It only exists in the
176 * indirect register space, before the actual PHY lane 2 registers. So the
177 * offset is absolute, not relative to COMPHY_LANE2_REGS_BASE.
178 * It is used only for SATA PHY initialization.
179 */
180 #define COMPHY_RESERVED_REG 0x0E
181 #define PHYCTRL_FRM_PIN_BIT BIT(13)
182
183 /* South Bridge PHY Configuration Registers */
184 #define COMPHY_PHY_REG(lane, reg) (((1 - (lane)) * 0x28) + ((reg) & 0x3f))
185
186 /*
187 * lane0: USB3/GbE1 PHY Configuration 1
188 * lane1: PCIe/GbE0 PHY Configuration 1
189 * (used only by SGMII code)
190 */
191 #define COMPHY_PHY_CFG1 0x0
192 #define PIN_PU_IVREF_BIT BIT(1)
193 #define PIN_RESET_CORE_BIT BIT(11)
194 #define PIN_RESET_COMPHY_BIT BIT(12)
195 #define PIN_PU_PLL_BIT BIT(16)
196 #define PIN_PU_RX_BIT BIT(17)
197 #define PIN_PU_TX_BIT BIT(18)
198 #define PIN_TX_IDLE_BIT BIT(19)
199 #define GEN_RX_SEL_MASK GENMASK(25, 22)
200 #define GEN_RX_SEL_VALUE(val) FIELD_PREP(GEN_RX_SEL_MASK, (val))
201 #define GEN_TX_SEL_MASK GENMASK(29, 26)
202 #define GEN_TX_SEL_VALUE(val) FIELD_PREP(GEN_TX_SEL_MASK, (val))
203 #define SERDES_SPEED_1_25_G 0x6
204 #define SERDES_SPEED_3_125_G 0x8
205 #define PHY_RX_INIT_BIT BIT(30)
206
207 /*
208 * lane0: USB3/GbE1 PHY Status 1
209 * lane1: PCIe/GbE0 PHY Status 1
210 * (used only by SGMII code)
211 */
212 #define COMPHY_PHY_STAT1 0x18
213 #define PHY_RX_INIT_DONE_BIT BIT(0)
214 #define PHY_PLL_READY_RX_BIT BIT(2)
215 #define PHY_PLL_READY_TX_BIT BIT(3)
216
217 /* PHY Selector */
218 #define COMPHY_SELECTOR_PHY_REG 0xFC
219 /* bit0: 0: Lane1 is GbE0; 1: Lane1 is PCIe */
220 #define COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT BIT(0)
221 /* bit4: 0: Lane0 is GbE1; 1: Lane0 is USB3 */
222 #define COMPHY_SELECTOR_USB3_GBE1_SEL_BIT BIT(4)
223 /* bit8: 0: Lane0 is USB3 instead of GbE1, Lane2 is SATA; 1: Lane2 is USB3 */
224 #define COMPHY_SELECTOR_USB3_PHY_SEL_BIT BIT(8)
225
226 struct mvebu_a3700_comphy_conf {
227 unsigned int lane;
228 enum phy_mode mode;
229 int submode;
230 };
231
232 #define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode) \
233 { \
234 .lane = _lane, \
235 .mode = _mode, \
236 .submode = _smode, \
237 }
238
239 #define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode) \
240 MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA)
241
242 #define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode) \
243 MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode)
244
245 static const struct mvebu_a3700_comphy_conf mvebu_a3700_comphy_modes[] = {
246 /* lane 0 */
247 MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS),
248 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII),
249 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_1000BASEX),
250 MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX),
251 /* lane 1 */
252 MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE),
253 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII),
254 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_1000BASEX),
255 MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX),
256 /* lane 2 */
257 MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA),
258 MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS),
259 };
260
261 struct mvebu_a3700_comphy_priv {
262 void __iomem *comphy_regs;
263 void __iomem *lane0_phy_regs; /* USB3 and GbE1 */
264 void __iomem *lane1_phy_regs; /* PCIe and GbE0 */
265 void __iomem *lane2_phy_indirect; /* SATA and USB3 */
266 spinlock_t lock; /* for PHY selector access */
267 bool xtal_is_40m;
268 };
269
270 struct mvebu_a3700_comphy_lane {
271 struct mvebu_a3700_comphy_priv *priv;
272 struct device *dev;
273 unsigned int id;
274 enum phy_mode mode;
275 int submode;
276 bool invert_tx;
277 bool invert_rx;
278 };
279
280 struct gbe_phy_init_data_fix {
281 u16 addr;
282 u16 value;
283 };
284
285 /* Changes to 40M1G25 mode data required for running 40M3G125 init mode */
286 static struct gbe_phy_init_data_fix gbe_phy_init_fix[] = {
287 { 0x005, 0x07CC }, { 0x015, 0x0000 }, { 0x01B, 0x0000 },
288 { 0x01D, 0x0000 }, { 0x01E, 0x0000 }, { 0x01F, 0x0000 },
289 { 0x020, 0x0000 }, { 0x021, 0x0030 }, { 0x026, 0x0888 },
290 { 0x04D, 0x0152 }, { 0x04F, 0xA020 }, { 0x050, 0x07CC },
291 { 0x053, 0xE9CA }, { 0x055, 0xBD97 }, { 0x071, 0x3015 },
292 { 0x076, 0x03AA }, { 0x07C, 0x0FDF }, { 0x0C2, 0x3030 },
293 { 0x0C3, 0x8000 }, { 0x0E2, 0x5550 }, { 0x0E3, 0x12A4 },
294 { 0x0E4, 0x7D00 }, { 0x0E6, 0x0C83 }, { 0x101, 0xFCC0 },
295 { 0x104, 0x0C10 }
296 };
297
298 /* 40M1G25 mode init data */
299 static u16 gbe_phy_init[512] = {
300 /* 0 1 2 3 4 5 6 7 */
301 /*-----------------------------------------------------------*/
302 /* 8 9 A B C D E F */
303 0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26, /* 00 */
304 0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52, /* 08 */
305 0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000, /* 10 */
306 0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF, /* 18 */
307 0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000, /* 20 */
308 0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, /* 28 */
309 0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */
310 0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100, /* 38 */
311 0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00, /* 40 */
312 0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A, /* 48 */
313 0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001, /* 50 */
314 0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF, /* 58 */
315 0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000, /* 60 */
316 0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002, /* 68 */
317 0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780, /* 70 */
318 0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000, /* 78 */
319 0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000, /* 80 */
320 0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210, /* 88 */
321 0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F, /* 90 */
322 0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651, /* 98 */
323 0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000, /* A0 */
324 0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* A8 */
325 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* B0 */
326 0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000, /* B8 */
327 0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003, /* C0 */
328 0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000, /* C8 */
329 0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00, /* D0 */
330 0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000, /* D8 */
331 0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541, /* E0 */
332 0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200, /* E8 */
333 0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000, /* F0 */
334 0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000, /* F8 */
335 0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000, /*100 */
336 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*108 */
337 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000, /*110 */
338 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*118 */
339 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*120 */
340 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*128 */
341 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*130 */
342 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*138 */
343 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*140 */
344 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*148 */
345 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*150 */
346 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*158 */
347 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*160 */
348 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*168 */
349 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*170 */
350 0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000, /*178 */
351 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*180 */
352 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*188 */
353 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*190 */
354 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*198 */
355 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A0 */
356 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A8 */
357 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B0 */
358 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B8 */
359 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C0 */
360 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C8 */
361 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D0 */
362 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D8 */
363 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E0 */
364 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E8 */
365 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1F0 */
366 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 /*1F8 */
367 };
368
comphy_reg_set(void __iomem * addr,u32 data,u32 mask)369 static inline void comphy_reg_set(void __iomem *addr, u32 data, u32 mask)
370 {
371 u32 val;
372
373 val = readl(addr);
374 val = (val & ~mask) | (data & mask);
375 writel(val, addr);
376 }
377
comphy_reg_set16(void __iomem * addr,u16 data,u16 mask)378 static inline void comphy_reg_set16(void __iomem *addr, u16 data, u16 mask)
379 {
380 u16 val;
381
382 val = readw(addr);
383 val = (val & ~mask) | (data & mask);
384 writew(val, addr);
385 }
386
387 /* Used for accessing lane 2 registers (SATA/USB3 PHY) */
comphy_set_indirect(struct mvebu_a3700_comphy_priv * priv,u32 offset,u16 data,u16 mask)388 static void comphy_set_indirect(struct mvebu_a3700_comphy_priv *priv,
389 u32 offset, u16 data, u16 mask)
390 {
391 writel(offset,
392 priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_ADDR);
393 comphy_reg_set(priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_DATA,
394 data, mask);
395 }
396
comphy_lane_reg_set(struct mvebu_a3700_comphy_lane * lane,u16 reg,u16 data,u16 mask)397 static void comphy_lane_reg_set(struct mvebu_a3700_comphy_lane *lane,
398 u16 reg, u16 data, u16 mask)
399 {
400 if (lane->id == 2) {
401 /* lane 2 PHY registers are accessed indirectly */
402 comphy_set_indirect(lane->priv,
403 reg + COMPHY_LANE2_REGS_BASE,
404 data, mask);
405 } else {
406 void __iomem *base = lane->id == 1 ?
407 lane->priv->lane1_phy_regs :
408 lane->priv->lane0_phy_regs;
409
410 comphy_reg_set16(base + COMPHY_LANE_REG_DIRECT(reg),
411 data, mask);
412 }
413 }
414
comphy_lane_reg_poll(struct mvebu_a3700_comphy_lane * lane,u16 reg,u16 bits,ulong sleep_us,ulong timeout_us)415 static int comphy_lane_reg_poll(struct mvebu_a3700_comphy_lane *lane,
416 u16 reg, u16 bits,
417 ulong sleep_us, ulong timeout_us)
418 {
419 int ret;
420
421 if (lane->id == 2) {
422 u32 data;
423
424 /* lane 2 PHY registers are accessed indirectly */
425 writel(reg + COMPHY_LANE2_REGS_BASE,
426 lane->priv->lane2_phy_indirect +
427 COMPHY_LANE2_INDIR_ADDR);
428
429 ret = readl_poll_timeout(lane->priv->lane2_phy_indirect +
430 COMPHY_LANE2_INDIR_DATA,
431 data, (data & bits) == bits,
432 sleep_us, timeout_us);
433 } else {
434 void __iomem *base = lane->id == 1 ?
435 lane->priv->lane1_phy_regs :
436 lane->priv->lane0_phy_regs;
437 u16 data;
438
439 ret = readw_poll_timeout(base + COMPHY_LANE_REG_DIRECT(reg),
440 data, (data & bits) == bits,
441 sleep_us, timeout_us);
442 }
443
444 return ret;
445 }
446
comphy_periph_reg_set(struct mvebu_a3700_comphy_lane * lane,u8 reg,u32 data,u32 mask)447 static void comphy_periph_reg_set(struct mvebu_a3700_comphy_lane *lane,
448 u8 reg, u32 data, u32 mask)
449 {
450 comphy_reg_set(lane->priv->comphy_regs + COMPHY_PHY_REG(lane->id, reg),
451 data, mask);
452 }
453
comphy_periph_reg_poll(struct mvebu_a3700_comphy_lane * lane,u8 reg,u32 bits,ulong sleep_us,ulong timeout_us)454 static int comphy_periph_reg_poll(struct mvebu_a3700_comphy_lane *lane,
455 u8 reg, u32 bits,
456 ulong sleep_us, ulong timeout_us)
457 {
458 u32 data;
459
460 return readl_poll_timeout(lane->priv->comphy_regs +
461 COMPHY_PHY_REG(lane->id, reg),
462 data, (data & bits) == bits,
463 sleep_us, timeout_us);
464 }
465
466 /* PHY selector configures with corresponding modes */
467 static int
mvebu_a3700_comphy_set_phy_selector(struct mvebu_a3700_comphy_lane * lane)468 mvebu_a3700_comphy_set_phy_selector(struct mvebu_a3700_comphy_lane *lane)
469 {
470 u32 old, new, clr = 0, set = 0;
471 unsigned long flags;
472
473 switch (lane->mode) {
474 case PHY_MODE_SATA:
475 /* SATA must be in Lane2 */
476 if (lane->id == 2)
477 clr = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
478 else
479 goto error;
480 break;
481
482 case PHY_MODE_ETHERNET:
483 if (lane->id == 0)
484 clr = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
485 else if (lane->id == 1)
486 clr = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
487 else
488 goto error;
489 break;
490
491 case PHY_MODE_USB_HOST_SS:
492 if (lane->id == 2)
493 set = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
494 else if (lane->id == 0)
495 set = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
496 else
497 goto error;
498 break;
499
500 case PHY_MODE_PCIE:
501 /* PCIE must be in Lane1 */
502 if (lane->id == 1)
503 set = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
504 else
505 goto error;
506 break;
507
508 default:
509 goto error;
510 }
511
512 spin_lock_irqsave(&lane->priv->lock, flags);
513
514 old = readl(lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
515 new = (old & ~clr) | set;
516 writel(new, lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
517
518 spin_unlock_irqrestore(&lane->priv->lock, flags);
519
520 dev_dbg(lane->dev,
521 "COMPHY[%d] mode[%d] changed PHY selector 0x%08x -> 0x%08x\n",
522 lane->id, lane->mode, old, new);
523
524 return 0;
525 error:
526 dev_err(lane->dev, "COMPHY[%d] mode[%d] is invalid\n", lane->id,
527 lane->mode);
528 return -EINVAL;
529 }
530
531 static int
mvebu_a3700_comphy_sata_power_on(struct mvebu_a3700_comphy_lane * lane)532 mvebu_a3700_comphy_sata_power_on(struct mvebu_a3700_comphy_lane *lane)
533 {
534 u32 mask, data, ref_clk;
535 int ret;
536
537 /* Configure phy selector for SATA */
538 ret = mvebu_a3700_comphy_set_phy_selector(lane);
539 if (ret)
540 return ret;
541
542 /* Clear phy isolation mode to make it work in normal mode */
543 comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
544 0x0, PHY_ISOLATE_MODE);
545
546 /* 0. Check the Polarity invert bits */
547 data = 0x0;
548 if (lane->invert_tx)
549 data |= TXD_INVERT_BIT;
550 if (lane->invert_rx)
551 data |= RXD_INVERT_BIT;
552 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
553 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
554
555 /* 1. Select 40-bit data width */
556 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
557 DATA_WIDTH_40BIT, SEL_DATA_WIDTH_MASK);
558
559 /* 2. Select reference clock(25M) and PHY mode (SATA) */
560 if (lane->priv->xtal_is_40m)
561 ref_clk = REF_FREF_SEL_SERDES_40MHZ;
562 else
563 ref_clk = REF_FREF_SEL_SERDES_25MHZ;
564
565 data = ref_clk | COMPHY_MODE_SATA;
566 mask = REF_FREF_SEL_MASK | COMPHY_MODE_MASK;
567 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
568
569 /* 3. Use maximum PLL rate (no power save) */
570 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
571 USE_MAX_PLL_RATE_BIT, USE_MAX_PLL_RATE_BIT);
572
573 /* 4. Reset reserved bit */
574 comphy_set_indirect(lane->priv, COMPHY_RESERVED_REG,
575 0x0, PHYCTRL_FRM_PIN_BIT);
576
577 /* 5. Set vendor-specific configuration (It is done in sata driver) */
578 /* XXX: in U-Boot below sequence was executed in this place, in Linux
579 * not. Now it is done only in U-Boot before this comphy
580 * initialization - tests shows that it works ok, but in case of any
581 * future problem it is left for reference.
582 * reg_set(MVEBU_REGS_BASE + 0xe00a0, 0, 0xffffffff);
583 * reg_set(MVEBU_REGS_BASE + 0xe00a4, BIT(6), BIT(6));
584 */
585
586 /* Wait for > 55 us to allow PLL be enabled */
587 udelay(PLL_SET_DELAY_US);
588
589 /* Polling status */
590 ret = comphy_lane_reg_poll(lane, COMPHY_DIG_LOOPBACK_EN,
591 PLL_READY_TX_BIT, COMPHY_PLL_SLEEP,
592 COMPHY_PLL_TIMEOUT);
593 if (ret)
594 dev_err(lane->dev, "Failed to lock SATA PLL\n");
595
596 return ret;
597 }
598
comphy_gbe_phy_init(struct mvebu_a3700_comphy_lane * lane,bool is_1gbps)599 static void comphy_gbe_phy_init(struct mvebu_a3700_comphy_lane *lane,
600 bool is_1gbps)
601 {
602 int addr, fix_idx;
603 u16 val;
604
605 fix_idx = 0;
606 for (addr = 0; addr < ARRAY_SIZE(gbe_phy_init); addr++) {
607 /*
608 * All PHY register values are defined in full for 3.125Gbps
609 * SERDES speed. The values required for 1.25 Gbps are almost
610 * the same and only few registers should be "fixed" in
611 * comparison to 3.125 Gbps values. These register values are
612 * stored in "gbe_phy_init_fix" array.
613 */
614 if (!is_1gbps &&
615 fix_idx < ARRAY_SIZE(gbe_phy_init_fix) &&
616 gbe_phy_init_fix[fix_idx].addr == addr) {
617 /* Use new value */
618 val = gbe_phy_init_fix[fix_idx].value;
619 fix_idx++;
620 } else {
621 val = gbe_phy_init[addr];
622 }
623
624 comphy_lane_reg_set(lane, addr, val, 0xFFFF);
625 }
626 }
627
628 static int
mvebu_a3700_comphy_ethernet_power_on(struct mvebu_a3700_comphy_lane * lane)629 mvebu_a3700_comphy_ethernet_power_on(struct mvebu_a3700_comphy_lane *lane)
630 {
631 u32 mask, data, speed_sel;
632 int ret;
633
634 /* Set selector */
635 ret = mvebu_a3700_comphy_set_phy_selector(lane);
636 if (ret)
637 return ret;
638
639 /*
640 * 1. Reset PHY by setting PHY input port PIN_RESET=1.
641 * 2. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep
642 * PHY TXP/TXN output to idle state during PHY initialization
643 * 3. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0.
644 */
645 data = PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT | PIN_RESET_COMPHY_BIT;
646 mask = data | PIN_RESET_CORE_BIT | PIN_PU_PLL_BIT | PIN_PU_RX_BIT |
647 PIN_PU_TX_BIT | PHY_RX_INIT_BIT;
648 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
649
650 /* 4. Release reset to the PHY by setting PIN_RESET=0. */
651 data = 0x0;
652 mask = PIN_RESET_COMPHY_BIT;
653 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
654
655 /*
656 * 5. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide COMPHY
657 * bit rate
658 */
659 switch (lane->submode) {
660 case PHY_INTERFACE_MODE_SGMII:
661 case PHY_INTERFACE_MODE_1000BASEX:
662 /* SGMII 1G, SerDes speed 1.25G */
663 speed_sel = SERDES_SPEED_1_25_G;
664 break;
665 case PHY_INTERFACE_MODE_2500BASEX:
666 /* 2500Base-X, SerDes speed 3.125G */
667 speed_sel = SERDES_SPEED_3_125_G;
668 break;
669 default:
670 /* Other rates are not supported */
671 dev_err(lane->dev,
672 "unsupported phy speed %d on comphy lane%d\n",
673 lane->submode, lane->id);
674 return -EINVAL;
675 }
676 data = GEN_RX_SEL_VALUE(speed_sel) | GEN_TX_SEL_VALUE(speed_sel);
677 mask = GEN_RX_SEL_MASK | GEN_TX_SEL_MASK;
678 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
679
680 /*
681 * 6. Wait 10mS for bandgap and reference clocks to stabilize; then
682 * start SW programming.
683 */
684 mdelay(10);
685
686 /* 7. Program COMPHY register PHY_MODE */
687 data = COMPHY_MODE_SERDES;
688 mask = COMPHY_MODE_MASK;
689 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
690
691 /*
692 * 8. Set COMPHY register REFCLK_SEL to select the correct REFCLK
693 * source
694 */
695 data = 0x0;
696 mask = PHY_REF_CLK_SEL;
697 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
698
699 /*
700 * 9. Set correct reference clock frequency in COMPHY register
701 * REF_FREF_SEL.
702 */
703 if (lane->priv->xtal_is_40m)
704 data = REF_FREF_SEL_SERDES_50MHZ;
705 else
706 data = REF_FREF_SEL_SERDES_25MHZ;
707
708 mask = REF_FREF_SEL_MASK;
709 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
710
711 /*
712 * 10. Program COMPHY register PHY_GEN_MAX[1:0]
713 * This step is mentioned in the flow received from verification team.
714 * However the PHY_GEN_MAX value is only meaningful for other interfaces
715 * (not SERDES). For instance, it selects SATA speed 1.5/3/6 Gbps or
716 * PCIe speed 2.5/5 Gbps
717 */
718
719 /*
720 * 11. Program COMPHY register SEL_BITS to set correct parallel data
721 * bus width
722 */
723 data = DATA_WIDTH_10BIT;
724 mask = SEL_DATA_WIDTH_MASK;
725 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, data, mask);
726
727 /*
728 * 12. As long as DFE function needs to be enabled in any mode,
729 * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F
730 * for real chip during COMPHY power on.
731 * The value of the DFE_UPDATE_EN already is 0x3F, because it is the
732 * default value after reset of the PHY.
733 */
734
735 /*
736 * 13. Program COMPHY GEN registers.
737 * These registers should be programmed based on the lab testing result
738 * to achieve optimal performance. Please contact the CEA group to get
739 * the related GEN table during real chip bring-up. We only required to
740 * run though the entire registers programming flow defined by
741 * "comphy_gbe_phy_init" when the REF clock is 40 MHz. For REF clock
742 * 25 MHz the default values stored in PHY registers are OK.
743 */
744 dev_dbg(lane->dev, "Running C-DPI phy init %s mode\n",
745 lane->submode == PHY_INTERFACE_MODE_2500BASEX ? "2G5" : "1G");
746 if (lane->priv->xtal_is_40m)
747 comphy_gbe_phy_init(lane,
748 lane->submode != PHY_INTERFACE_MODE_2500BASEX);
749
750 /*
751 * 14. Check the PHY Polarity invert bit
752 */
753 data = 0x0;
754 if (lane->invert_tx)
755 data |= TXD_INVERT_BIT;
756 if (lane->invert_rx)
757 data |= RXD_INVERT_BIT;
758 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
759 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
760
761 /*
762 * 15. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 to
763 * start PHY power up sequence. All the PHY register programming should
764 * be done before PIN_PU_PLL=1. There should be no register programming
765 * for normal PHY operation from this point.
766 */
767 data = PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT;
768 mask = data;
769 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
770
771 /*
772 * 16. Wait for PHY power up sequence to finish by checking output ports
773 * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1.
774 */
775 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
776 PHY_PLL_READY_TX_BIT |
777 PHY_PLL_READY_RX_BIT,
778 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
779 if (ret) {
780 dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
781 lane->id);
782 return ret;
783 }
784
785 /*
786 * 17. Set COMPHY input port PIN_TX_IDLE=0
787 */
788 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, 0x0, PIN_TX_IDLE_BIT);
789
790 /*
791 * 18. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. To
792 * start RX initialization. PIN_RX_INIT_DONE will be cleared to 0 by the
793 * PHY After RX initialization is done, PIN_RX_INIT_DONE will be set to
794 * 1 by COMPHY Set PIN_RX_INIT=0 after PIN_RX_INIT_DONE= 1. Please
795 * refer to RX initialization part for details.
796 */
797 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1,
798 PHY_RX_INIT_BIT, PHY_RX_INIT_BIT);
799
800 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
801 PHY_PLL_READY_TX_BIT |
802 PHY_PLL_READY_RX_BIT,
803 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
804 if (ret) {
805 dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
806 lane->id);
807 return ret;
808 }
809
810 ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
811 PHY_RX_INIT_DONE_BIT,
812 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
813 if (ret)
814 dev_err(lane->dev, "Failed to init RX of SERDES PHY %d\n",
815 lane->id);
816
817 return ret;
818 }
819
820 static int
mvebu_a3700_comphy_usb3_power_on(struct mvebu_a3700_comphy_lane * lane)821 mvebu_a3700_comphy_usb3_power_on(struct mvebu_a3700_comphy_lane *lane)
822 {
823 u32 mask, data, cfg, ref_clk;
824 int ret;
825
826 /* Set phy seclector */
827 ret = mvebu_a3700_comphy_set_phy_selector(lane);
828 if (ret)
829 return ret;
830
831 /* COMPHY register reset (cleared automatically) */
832 comphy_lane_reg_set(lane, COMPHY_SFT_RESET, SFT_RST, SFT_RST);
833
834 /*
835 * 0. Set PHY OTG Control(0x5d034), bit 4, Power up OTG module The
836 * register belong to UTMI module, so it is set in UTMI phy driver.
837 */
838
839 /*
840 * 1. Set PRD_TXDEEMPH (3.5db de-emph)
841 */
842 data = PRD_TXDEEMPH0_MASK;
843 mask = PRD_TXDEEMPH0_MASK | PRD_TXMARGIN_MASK | PRD_TXSWING_MASK |
844 CFG_TX_ALIGN_POS_MASK;
845 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG0, data, mask);
846
847 /*
848 * 2. Set BIT0: enable transmitter in high impedance mode
849 * Set BIT[3:4]: delay 2 clock cycles for HiZ off latency
850 * Set BIT6: Tx detect Rx at HiZ mode
851 * Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db
852 * together with bit 0 of COMPHY_PIPE_LANE_CFG0 register
853 */
854 data = TX_DET_RX_MODE | GEN2_TX_DATA_DLY_DEFT | TX_ELEC_IDLE_MODE_EN;
855 mask = PRD_TXDEEMPH1_MASK | TX_DET_RX_MODE | GEN2_TX_DATA_DLY_MASK |
856 TX_ELEC_IDLE_MODE_EN;
857 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1, data, mask);
858
859 /*
860 * 3. Set Spread Spectrum Clock Enabled
861 */
862 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG4,
863 SPREAD_SPECTRUM_CLK_EN, SPREAD_SPECTRUM_CLK_EN);
864
865 /*
866 * 4. Set Override Margining Controls From the MAC:
867 * Use margining signals from lane configuration
868 */
869 comphy_lane_reg_set(lane, COMPHY_PIPE_TEST_MODE_CTRL,
870 MODE_MARGIN_OVERRIDE, 0xFFFF);
871
872 /*
873 * 5. Set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles
874 * set Mode Clock Source = PCLK is generated from REFCLK
875 */
876 data = 0x0;
877 mask = MODE_CLK_SRC | BUNDLE_PERIOD_SEL | BUNDLE_PERIOD_SCALE_MASK |
878 BUNDLE_SAMPLE_CTRL | PLL_READY_DLY_MASK;
879 comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO, data, mask);
880
881 /*
882 * 6. Set G2 Spread Spectrum Clock Amplitude at 4K
883 */
884 comphy_lane_reg_set(lane, COMPHY_GEN2_SET2,
885 GS2_TX_SSC_AMP_4128, GS2_TX_SSC_AMP_MASK);
886
887 /*
888 * 7. Unset G3 Spread Spectrum Clock Amplitude
889 * set G3 TX and RX Register Master Current Select
890 */
891 data = GS2_VREG_RXTX_MAS_ISET_60U;
892 mask = GS2_TX_SSC_AMP_MASK | GS2_VREG_RXTX_MAS_ISET_MASK |
893 GS2_RSVD_6_0_MASK;
894 comphy_lane_reg_set(lane, COMPHY_GEN3_SET2, data, mask);
895
896 /*
897 * 8. Check crystal jumper setting and program the Power and PLL Control
898 * accordingly Change RX wait
899 */
900 if (lane->priv->xtal_is_40m) {
901 ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
902 cfg = CFG_PM_RXDLOZ_WAIT_12_UNIT;
903 } else {
904 ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
905 cfg = CFG_PM_RXDLOZ_WAIT_7_UNIT;
906 }
907
908 data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
909 PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_USB3 | ref_clk;
910 mask = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
911 PU_TX_INTP_BIT | PU_DFE_BIT | PLL_LOCK_BIT | COMPHY_MODE_MASK |
912 REF_FREF_SEL_MASK;
913 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
914
915 data = CFG_PM_RXDEN_WAIT_1_UNIT | cfg;
916 mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
917 CFG_PM_RXDLOZ_WAIT_MASK;
918 comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
919
920 /*
921 * 9. Enable idle sync
922 */
923 comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
924 IDLE_SYNC_EN, IDLE_SYNC_EN);
925
926 /*
927 * 10. Enable the output of 500M clock
928 */
929 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, CLK500M_EN, CLK500M_EN);
930
931 /*
932 * 11. Set 20-bit data width
933 */
934 comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
935 DATA_WIDTH_20BIT, 0xFFFF);
936
937 /*
938 * 12. Override Speed_PLL value and use MAC PLL
939 */
940 data = SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT;
941 mask = 0xFFFF;
942 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, data, mask);
943
944 /*
945 * 13. Check the Polarity invert bit
946 */
947 data = 0x0;
948 if (lane->invert_tx)
949 data |= TXD_INVERT_BIT;
950 if (lane->invert_rx)
951 data |= RXD_INVERT_BIT;
952 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
953 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
954
955 /*
956 * 14. Set max speed generation to USB3.0 5Gbps
957 */
958 comphy_lane_reg_set(lane, COMPHY_SYNC_MASK_GEN,
959 PHY_GEN_MAX_USB3_5G, PHY_GEN_MAX_MASK);
960
961 /*
962 * 15. Set capacitor value for FFE gain peaking to 0xF
963 */
964 comphy_lane_reg_set(lane, COMPHY_GEN2_SET3,
965 GS3_FFE_CAP_SEL_VALUE, GS3_FFE_CAP_SEL_MASK);
966
967 /*
968 * 16. Release SW reset
969 */
970 data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32 | MODE_REFDIV_BY_4;
971 mask = 0xFFFF;
972 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
973
974 /* Wait for > 55 us to allow PCLK be enabled */
975 udelay(PLL_SET_DELAY_US);
976
977 ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
978 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
979 if (ret)
980 dev_err(lane->dev, "Failed to lock USB3 PLL\n");
981
982 return ret;
983 }
984
985 static int
mvebu_a3700_comphy_pcie_power_on(struct mvebu_a3700_comphy_lane * lane)986 mvebu_a3700_comphy_pcie_power_on(struct mvebu_a3700_comphy_lane *lane)
987 {
988 u32 mask, data, ref_clk;
989 int ret;
990
991 /* Configure phy selector for PCIe */
992 ret = mvebu_a3700_comphy_set_phy_selector(lane);
993 if (ret)
994 return ret;
995
996 /* 1. Enable max PLL. */
997 comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1,
998 USE_MAX_PLL_RATE_EN, USE_MAX_PLL_RATE_EN);
999
1000 /* 2. Select 20 bit SERDES interface. */
1001 comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO,
1002 CFG_SEL_20B, CFG_SEL_20B);
1003
1004 /* 3. Force to use reg setting for PCIe mode */
1005 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL1,
1006 SEL_BITS_PCIE_FORCE, SEL_BITS_PCIE_FORCE);
1007
1008 /* 4. Change RX wait */
1009 data = CFG_PM_RXDEN_WAIT_1_UNIT | CFG_PM_RXDLOZ_WAIT_12_UNIT;
1010 mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
1011 CFG_PM_RXDLOZ_WAIT_MASK;
1012 comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
1013
1014 /* 5. Enable idle sync */
1015 comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
1016 IDLE_SYNC_EN, IDLE_SYNC_EN);
1017
1018 /* 6. Enable the output of 100M/125M/500M clock */
1019 data = CLK500M_EN | TXDCLK_2X_SEL | CLK100M_125M_EN;
1020 mask = data;
1021 comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
1022
1023 /*
1024 * 7. Enable TX, PCIE global register, 0xd0074814, it is done in
1025 * PCI-E driver
1026 */
1027
1028 /*
1029 * 8. Check crystal jumper setting and program the Power and PLL
1030 * Control accordingly
1031 */
1032
1033 if (lane->priv->xtal_is_40m)
1034 ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
1035 else
1036 ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
1037
1038 data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
1039 PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_PCIE | ref_clk;
1040 mask = 0xFFFF;
1041 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
1042
1043 /* 9. Override Speed_PLL value and use MAC PLL */
1044 comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
1045 SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT,
1046 0xFFFF);
1047
1048 /* 10. Check the Polarity invert bit */
1049 data = 0x0;
1050 if (lane->invert_tx)
1051 data |= TXD_INVERT_BIT;
1052 if (lane->invert_rx)
1053 data |= RXD_INVERT_BIT;
1054 mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
1055 comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
1056
1057 /* 11. Release SW reset */
1058 data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32;
1059 mask = data | PIPE_SOFT_RESET | MODE_REFDIV_MASK;
1060 comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
1061
1062 /* Wait for > 55 us to allow PCLK be enabled */
1063 udelay(PLL_SET_DELAY_US);
1064
1065 ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
1066 COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
1067 if (ret)
1068 dev_err(lane->dev, "Failed to lock PCIE PLL\n");
1069
1070 return ret;
1071 }
1072
1073 static void
mvebu_a3700_comphy_sata_power_off(struct mvebu_a3700_comphy_lane * lane)1074 mvebu_a3700_comphy_sata_power_off(struct mvebu_a3700_comphy_lane *lane)
1075 {
1076 /* Set phy isolation mode */
1077 comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
1078 PHY_ISOLATE_MODE, PHY_ISOLATE_MODE);
1079
1080 /* Power off PLL, Tx, Rx */
1081 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1082 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1083 }
1084
1085 static void
mvebu_a3700_comphy_ethernet_power_off(struct mvebu_a3700_comphy_lane * lane)1086 mvebu_a3700_comphy_ethernet_power_off(struct mvebu_a3700_comphy_lane *lane)
1087 {
1088 u32 mask, data;
1089
1090 data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT | PIN_PU_IVREF_BIT |
1091 PHY_RX_INIT_BIT;
1092 mask = data;
1093 comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
1094 }
1095
1096 static void
mvebu_a3700_comphy_pcie_power_off(struct mvebu_a3700_comphy_lane * lane)1097 mvebu_a3700_comphy_pcie_power_off(struct mvebu_a3700_comphy_lane *lane)
1098 {
1099 /* Power off PLL, Tx, Rx */
1100 comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1101 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1102 }
1103
mvebu_a3700_comphy_usb3_power_off(struct mvebu_a3700_comphy_lane * lane)1104 static void mvebu_a3700_comphy_usb3_power_off(struct mvebu_a3700_comphy_lane *lane)
1105 {
1106 /*
1107 * The USB3 MAC sets the USB3 PHY to low state, so we do not
1108 * need to power off USB3 PHY again.
1109 */
1110 }
1111
mvebu_a3700_comphy_check_mode(int lane,enum phy_mode mode,int submode)1112 static bool mvebu_a3700_comphy_check_mode(int lane,
1113 enum phy_mode mode,
1114 int submode)
1115 {
1116 int i, n = ARRAY_SIZE(mvebu_a3700_comphy_modes);
1117
1118 /* Unused PHY mux value is 0x0 */
1119 if (mode == PHY_MODE_INVALID)
1120 return false;
1121
1122 for (i = 0; i < n; i++) {
1123 if (mvebu_a3700_comphy_modes[i].lane == lane &&
1124 mvebu_a3700_comphy_modes[i].mode == mode &&
1125 mvebu_a3700_comphy_modes[i].submode == submode)
1126 break;
1127 }
1128
1129 if (i == n)
1130 return false;
1131
1132 return true;
1133 }
1134
mvebu_a3700_comphy_set_mode(struct phy * phy,enum phy_mode mode,int submode)1135 static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode,
1136 int submode)
1137 {
1138 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1139
1140 if (!mvebu_a3700_comphy_check_mode(lane->id, mode, submode)) {
1141 dev_err(lane->dev, "invalid COMPHY mode\n");
1142 return -EINVAL;
1143 }
1144
1145 /* Mode cannot be changed while the PHY is powered on */
1146 if (phy->power_count &&
1147 (lane->mode != mode || lane->submode != submode))
1148 return -EBUSY;
1149
1150 /* Just remember the mode, ->power_on() will do the real setup */
1151 lane->mode = mode;
1152 lane->submode = submode;
1153
1154 return 0;
1155 }
1156
mvebu_a3700_comphy_power_on(struct phy * phy)1157 static int mvebu_a3700_comphy_power_on(struct phy *phy)
1158 {
1159 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1160
1161 if (!mvebu_a3700_comphy_check_mode(lane->id, lane->mode,
1162 lane->submode)) {
1163 dev_err(lane->dev, "invalid COMPHY mode\n");
1164 return -EINVAL;
1165 }
1166
1167 switch (lane->mode) {
1168 case PHY_MODE_USB_HOST_SS:
1169 dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id);
1170 return mvebu_a3700_comphy_usb3_power_on(lane);
1171 case PHY_MODE_SATA:
1172 dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id);
1173 return mvebu_a3700_comphy_sata_power_on(lane);
1174 case PHY_MODE_ETHERNET:
1175 dev_dbg(lane->dev, "set lane %d to Ethernet mode\n", lane->id);
1176 return mvebu_a3700_comphy_ethernet_power_on(lane);
1177 case PHY_MODE_PCIE:
1178 dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id);
1179 return mvebu_a3700_comphy_pcie_power_on(lane);
1180 default:
1181 dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode);
1182 return -EOPNOTSUPP;
1183 }
1184 }
1185
mvebu_a3700_comphy_power_off(struct phy * phy)1186 static int mvebu_a3700_comphy_power_off(struct phy *phy)
1187 {
1188 struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1189
1190 switch (lane->id) {
1191 case 0:
1192 mvebu_a3700_comphy_usb3_power_off(lane);
1193 mvebu_a3700_comphy_ethernet_power_off(lane);
1194 return 0;
1195 case 1:
1196 mvebu_a3700_comphy_pcie_power_off(lane);
1197 mvebu_a3700_comphy_ethernet_power_off(lane);
1198 return 0;
1199 case 2:
1200 mvebu_a3700_comphy_usb3_power_off(lane);
1201 mvebu_a3700_comphy_sata_power_off(lane);
1202 return 0;
1203 default:
1204 dev_err(lane->dev, "invalid COMPHY mode\n");
1205 return -EINVAL;
1206 }
1207 }
1208
1209 static const struct phy_ops mvebu_a3700_comphy_ops = {
1210 .power_on = mvebu_a3700_comphy_power_on,
1211 .power_off = mvebu_a3700_comphy_power_off,
1212 .set_mode = mvebu_a3700_comphy_set_mode,
1213 .owner = THIS_MODULE,
1214 };
1215
mvebu_a3700_comphy_xlate(struct device * dev,const struct of_phandle_args * args)1216 static struct phy *mvebu_a3700_comphy_xlate(struct device *dev,
1217 const struct of_phandle_args *args)
1218 {
1219 struct mvebu_a3700_comphy_lane *lane;
1220 unsigned int port;
1221 struct phy *phy;
1222
1223 phy = of_phy_simple_xlate(dev, args);
1224 if (IS_ERR(phy))
1225 return phy;
1226
1227 lane = phy_get_drvdata(phy);
1228
1229 port = args->args[0];
1230 if (port != 0 && (port != 1 || lane->id != 0)) {
1231 dev_err(lane->dev, "invalid port number %u\n", port);
1232 return ERR_PTR(-EINVAL);
1233 }
1234
1235 lane->invert_tx = args->args[1] & BIT(0);
1236 lane->invert_rx = args->args[1] & BIT(1);
1237
1238 return phy;
1239 }
1240
mvebu_a3700_comphy_probe(struct platform_device * pdev)1241 static int mvebu_a3700_comphy_probe(struct platform_device *pdev)
1242 {
1243 struct mvebu_a3700_comphy_priv *priv;
1244 struct phy_provider *provider;
1245 struct device_node *child;
1246 struct resource *res;
1247 struct clk *clk;
1248 int ret;
1249
1250 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
1251 if (!priv)
1252 return -ENOMEM;
1253
1254 spin_lock_init(&priv->lock);
1255
1256 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "comphy");
1257 priv->comphy_regs = devm_ioremap_resource(&pdev->dev, res);
1258 if (IS_ERR(priv->comphy_regs))
1259 return PTR_ERR(priv->comphy_regs);
1260
1261 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1262 "lane1_pcie_gbe");
1263 priv->lane1_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1264 if (IS_ERR(priv->lane1_phy_regs))
1265 return PTR_ERR(priv->lane1_phy_regs);
1266
1267 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1268 "lane0_usb3_gbe");
1269 priv->lane0_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1270 if (IS_ERR(priv->lane0_phy_regs))
1271 return PTR_ERR(priv->lane0_phy_regs);
1272
1273 res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1274 "lane2_sata_usb3");
1275 priv->lane2_phy_indirect = devm_ioremap_resource(&pdev->dev, res);
1276 if (IS_ERR(priv->lane2_phy_indirect))
1277 return PTR_ERR(priv->lane2_phy_indirect);
1278
1279 /*
1280 * Driver needs to know if reference xtal clock is 40MHz or 25MHz.
1281 * Old DT bindings do not have xtal clk present. So do not fail here
1282 * and expects that default 25MHz reference clock is used.
1283 */
1284 clk = clk_get(&pdev->dev, "xtal");
1285 if (IS_ERR(clk)) {
1286 if (PTR_ERR(clk) == -EPROBE_DEFER)
1287 return -EPROBE_DEFER;
1288 dev_warn(&pdev->dev, "missing 'xtal' clk (%ld)\n",
1289 PTR_ERR(clk));
1290 } else {
1291 ret = clk_prepare_enable(clk);
1292 if (ret) {
1293 dev_warn(&pdev->dev, "enabling xtal clk failed (%d)\n",
1294 ret);
1295 } else {
1296 if (clk_get_rate(clk) == 40000000)
1297 priv->xtal_is_40m = true;
1298 clk_disable_unprepare(clk);
1299 }
1300 clk_put(clk);
1301 }
1302
1303 dev_set_drvdata(&pdev->dev, priv);
1304
1305 for_each_available_child_of_node(pdev->dev.of_node, child) {
1306 struct mvebu_a3700_comphy_lane *lane;
1307 struct phy *phy;
1308 int ret;
1309 u32 lane_id;
1310
1311 ret = of_property_read_u32(child, "reg", &lane_id);
1312 if (ret < 0) {
1313 dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
1314 ret);
1315 continue;
1316 }
1317
1318 if (lane_id >= 3) {
1319 dev_err(&pdev->dev, "invalid 'reg' property\n");
1320 continue;
1321 }
1322
1323 lane = devm_kzalloc(&pdev->dev, sizeof(*lane), GFP_KERNEL);
1324 if (!lane) {
1325 of_node_put(child);
1326 return -ENOMEM;
1327 }
1328
1329 phy = devm_phy_create(&pdev->dev, child,
1330 &mvebu_a3700_comphy_ops);
1331 if (IS_ERR(phy)) {
1332 of_node_put(child);
1333 return PTR_ERR(phy);
1334 }
1335
1336 lane->priv = priv;
1337 lane->dev = &pdev->dev;
1338 lane->mode = PHY_MODE_INVALID;
1339 lane->submode = PHY_INTERFACE_MODE_NA;
1340 lane->id = lane_id;
1341 lane->invert_tx = false;
1342 lane->invert_rx = false;
1343 phy_set_drvdata(phy, lane);
1344
1345 /*
1346 * To avoid relying on the bootloader/firmware configuration,
1347 * power off all comphys.
1348 */
1349 mvebu_a3700_comphy_power_off(phy);
1350 }
1351
1352 provider = devm_of_phy_provider_register(&pdev->dev,
1353 mvebu_a3700_comphy_xlate);
1354
1355 return PTR_ERR_OR_ZERO(provider);
1356 }
1357
1358 static const struct of_device_id mvebu_a3700_comphy_of_match_table[] = {
1359 { .compatible = "marvell,comphy-a3700" },
1360 { },
1361 };
1362 MODULE_DEVICE_TABLE(of, mvebu_a3700_comphy_of_match_table);
1363
1364 static struct platform_driver mvebu_a3700_comphy_driver = {
1365 .probe = mvebu_a3700_comphy_probe,
1366 .driver = {
1367 .name = "mvebu-a3700-comphy",
1368 .of_match_table = mvebu_a3700_comphy_of_match_table,
1369 },
1370 };
1371 module_platform_driver(mvebu_a3700_comphy_driver);
1372
1373 MODULE_AUTHOR("Miquèl Raynal <miquel.raynal@bootlin.com>");
1374 MODULE_AUTHOR("Pali Rohár <pali@kernel.org>");
1375 MODULE_AUTHOR("Marek Behún <kabel@kernel.org>");
1376 MODULE_DESCRIPTION("Common PHY driver for A3700");
1377 MODULE_LICENSE("GPL v2");
1378