1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * mxser.c -- MOXA Smartio/Industio family multiport serial driver.
4 *
5 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
6 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
7 *
8 * This code is loosely based on the 1.8 moxa driver which is based on
9 * Linux serial driver, written by Linus Torvalds, Theodore T'so and
10 * others.
11 *
12 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
13 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
14 * www.moxa.com.
15 * - Fixed x86_64 cleanness
16 */
17
18 #include <linux/module.h>
19 #include <linux/errno.h>
20 #include <linux/signal.h>
21 #include <linux/sched.h>
22 #include <linux/timer.h>
23 #include <linux/interrupt.h>
24 #include <linux/tty.h>
25 #include <linux/tty_flip.h>
26 #include <linux/serial.h>
27 #include <linux/serial_reg.h>
28 #include <linux/major.h>
29 #include <linux/string.h>
30 #include <linux/fcntl.h>
31 #include <linux/ptrace.h>
32 #include <linux/ioport.h>
33 #include <linux/mm.h>
34 #include <linux/delay.h>
35 #include <linux/pci.h>
36 #include <linux/bitops.h>
37 #include <linux/slab.h>
38 #include <linux/ratelimit.h>
39
40 #include <asm/io.h>
41 #include <asm/irq.h>
42 #include <linux/uaccess.h>
43
44 /*
45 * Semi-public control interfaces
46 */
47
48 /*
49 * MOXA ioctls
50 */
51
52 #define MOXA 0x400
53 #define MOXA_SET_OP_MODE (MOXA + 66)
54 #define MOXA_GET_OP_MODE (MOXA + 67)
55
56 #define RS232_MODE 0
57 #define RS485_2WIRE_MODE 1
58 #define RS422_MODE 2
59 #define RS485_4WIRE_MODE 3
60 #define OP_MODE_MASK 3
61
62 /* --------------------------------------------------- */
63
64 /*
65 * Follow just what Moxa Must chip defines.
66 *
67 * When LCR register (offset 0x03) is written the following value, the Must chip
68 * will enter enhanced mode. And a write to EFR (offset 0x02) bit 6,7 will
69 * change bank.
70 */
71 #define MOXA_MUST_ENTER_ENHANCED 0xBF
72
73 /* when enhanced mode is enabled, access to general bank register */
74 #define MOXA_MUST_GDL_REGISTER 0x07
75 #define MOXA_MUST_GDL_MASK 0x7F
76 #define MOXA_MUST_GDL_HAS_BAD_DATA 0x80
77
78 #define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */
79 /* enhanced register bank select and enhanced mode setting register */
80 /* This works only when LCR register equals to 0xBF */
81 #define MOXA_MUST_EFR_REGISTER 0x02
82 #define MOXA_MUST_EFR_EFRB_ENABLE 0x10 /* enhanced mode enable */
83 /* enhanced register bank set 0, 1, 2 */
84 #define MOXA_MUST_EFR_BANK0 0x00
85 #define MOXA_MUST_EFR_BANK1 0x40
86 #define MOXA_MUST_EFR_BANK2 0x80
87 #define MOXA_MUST_EFR_BANK3 0xC0
88 #define MOXA_MUST_EFR_BANK_MASK 0xC0
89
90 /* set XON1 value register, when LCR=0xBF and change to bank0 */
91 #define MOXA_MUST_XON1_REGISTER 0x04
92
93 /* set XON2 value register, when LCR=0xBF and change to bank0 */
94 #define MOXA_MUST_XON2_REGISTER 0x05
95
96 /* set XOFF1 value register, when LCR=0xBF and change to bank0 */
97 #define MOXA_MUST_XOFF1_REGISTER 0x06
98
99 /* set XOFF2 value register, when LCR=0xBF and change to bank0 */
100 #define MOXA_MUST_XOFF2_REGISTER 0x07
101
102 #define MOXA_MUST_RBRTL_REGISTER 0x04
103 #define MOXA_MUST_RBRTH_REGISTER 0x05
104 #define MOXA_MUST_RBRTI_REGISTER 0x06
105 #define MOXA_MUST_THRTL_REGISTER 0x07
106 #define MOXA_MUST_ENUM_REGISTER 0x04
107 #define MOXA_MUST_HWID_REGISTER 0x05
108 #define MOXA_MUST_ECR_REGISTER 0x06
109 #define MOXA_MUST_CSR_REGISTER 0x07
110
111 #define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 /* good data mode enable */
112 #define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 /* only good data put into RxFIFO */
113
114 #define MOXA_MUST_IER_ECTSI 0x80 /* enable CTS interrupt */
115 #define MOXA_MUST_IER_ERTSI 0x40 /* enable RTS interrupt */
116 #define MOXA_MUST_IER_XINT 0x20 /* enable Xon/Xoff interrupt */
117 #define MOXA_MUST_IER_EGDAI 0x10 /* enable GDA interrupt */
118
119 #define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI)
120
121 /* GDA interrupt pending */
122 #define MOXA_MUST_IIR_GDA 0x1C
123 #define MOXA_MUST_IIR_RDA 0x04
124 #define MOXA_MUST_IIR_RTO 0x0C
125 #define MOXA_MUST_IIR_LSR 0x06
126
127 /* received Xon/Xoff or specical interrupt pending */
128 #define MOXA_MUST_IIR_XSC 0x10
129
130 /* RTS/CTS change state interrupt pending */
131 #define MOXA_MUST_IIR_RTSCTS 0x20
132 #define MOXA_MUST_IIR_MASK 0x3E
133
134 #define MOXA_MUST_MCR_XON_FLAG 0x40
135 #define MOXA_MUST_MCR_XON_ANY 0x80
136 #define MOXA_MUST_MCR_TX_XON 0x08
137
138 #define MOXA_MUST_EFR_SF_MASK 0x0F /* software flow control on chip mask value */
139 #define MOXA_MUST_EFR_SF_TX1 0x08 /* send Xon1/Xoff1 */
140 #define MOXA_MUST_EFR_SF_TX2 0x04 /* send Xon2/Xoff2 */
141 #define MOXA_MUST_EFR_SF_TX12 0x0C /* send Xon1,Xon2/Xoff1,Xoff2 */
142 #define MOXA_MUST_EFR_SF_TX_NO 0x00 /* don't send Xon/Xoff */
143 #define MOXA_MUST_EFR_SF_TX_MASK 0x0C /* Tx software flow control mask */
144 #define MOXA_MUST_EFR_SF_RX_NO 0x00 /* don't receive Xon/Xoff */
145 #define MOXA_MUST_EFR_SF_RX1 0x02 /* receive Xon1/Xoff1 */
146 #define MOXA_MUST_EFR_SF_RX2 0x01 /* receive Xon2/Xoff2 */
147 #define MOXA_MUST_EFR_SF_RX12 0x03 /* receive Xon1,Xon2/Xoff1,Xoff2 */
148 #define MOXA_MUST_EFR_SF_RX_MASK 0x03 /* Rx software flow control mask */
149
150 #define MXSERMAJOR 174
151
152 #define MXSER_BOARDS 4 /* Max. boards */
153 #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */
154 #define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
155 #define MXSER_ISR_PASS_LIMIT 100
156
157 #define WAKEUP_CHARS 256
158
159 #define MXSER_BAUD_BASE 921600
160 #define MXSER_CUSTOM_DIVISOR (MXSER_BAUD_BASE * 16)
161
162 #define PCI_DEVICE_ID_MOXA_RC7000 0x0001
163 #define PCI_DEVICE_ID_MOXA_CP102 0x1020
164 #define PCI_DEVICE_ID_MOXA_CP102UL 0x1021
165 #define PCI_DEVICE_ID_MOXA_CP102U 0x1022
166 #define PCI_DEVICE_ID_MOXA_CP102UF 0x1023
167 #define PCI_DEVICE_ID_MOXA_C104 0x1040
168 #define PCI_DEVICE_ID_MOXA_CP104U 0x1041
169 #define PCI_DEVICE_ID_MOXA_CP104JU 0x1042
170 #define PCI_DEVICE_ID_MOXA_CP104EL 0x1043
171 #define PCI_DEVICE_ID_MOXA_POS104UL 0x1044
172 #define PCI_DEVICE_ID_MOXA_CB108 0x1080
173 #define PCI_DEVICE_ID_MOXA_CP112UL 0x1120
174 #define PCI_DEVICE_ID_MOXA_CT114 0x1140
175 #define PCI_DEVICE_ID_MOXA_CP114 0x1141
176 #define PCI_DEVICE_ID_MOXA_CB114 0x1142
177 #define PCI_DEVICE_ID_MOXA_CP114UL 0x1143
178 #define PCI_DEVICE_ID_MOXA_CP118U 0x1180
179 #define PCI_DEVICE_ID_MOXA_CP118EL 0x1181
180 #define PCI_DEVICE_ID_MOXA_CP132 0x1320
181 #define PCI_DEVICE_ID_MOXA_CP132U 0x1321
182 #define PCI_DEVICE_ID_MOXA_CP134U 0x1340
183 #define PCI_DEVICE_ID_MOXA_CB134I 0x1341
184 #define PCI_DEVICE_ID_MOXA_CP138U 0x1380
185 #define PCI_DEVICE_ID_MOXA_C168 0x1680
186 #define PCI_DEVICE_ID_MOXA_CP168U 0x1681
187 #define PCI_DEVICE_ID_MOXA_CP168EL 0x1682
188
189 #define MXSER_NPORTS(ddata) ((ddata) & 0xffU)
190 #define MXSER_HIGHBAUD 0x0100
191
192 enum mxser_must_hwid {
193 MOXA_OTHER_UART = 0x00,
194 MOXA_MUST_MU150_HWID = 0x01,
195 MOXA_MUST_MU860_HWID = 0x02,
196 };
197
198 static const struct {
199 u8 type;
200 u8 fifo_size;
201 u8 rx_high_water;
202 u8 rx_low_water;
203 speed_t max_baud;
204 } Gpci_uart_info[] = {
205 { MOXA_OTHER_UART, 16, 14, 1, 921600 },
206 { MOXA_MUST_MU150_HWID, 64, 48, 16, 230400 },
207 { MOXA_MUST_MU860_HWID, 128, 96, 32, 921600 }
208 };
209 #define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info)
210
211 static const struct pci_device_id mxser_pcibrds[] = {
212 { PCI_DEVICE_DATA(MOXA, C168, 8) },
213 { PCI_DEVICE_DATA(MOXA, C104, 4) },
214 { PCI_DEVICE_DATA(MOXA, CP132, 2) },
215 { PCI_DEVICE_DATA(MOXA, CP114, 4) },
216 { PCI_DEVICE_DATA(MOXA, CT114, 4) },
217 { PCI_DEVICE_DATA(MOXA, CP102, 2 | MXSER_HIGHBAUD) },
218 { PCI_DEVICE_DATA(MOXA, CP104U, 4) },
219 { PCI_DEVICE_DATA(MOXA, CP168U, 8) },
220 { PCI_DEVICE_DATA(MOXA, CP132U, 2) },
221 { PCI_DEVICE_DATA(MOXA, CP134U, 4) },
222 { PCI_DEVICE_DATA(MOXA, CP104JU, 4) },
223 { PCI_DEVICE_DATA(MOXA, RC7000, 8) }, /* RC7000 */
224 { PCI_DEVICE_DATA(MOXA, CP118U, 8) },
225 { PCI_DEVICE_DATA(MOXA, CP102UL, 2) },
226 { PCI_DEVICE_DATA(MOXA, CP102U, 2) },
227 { PCI_DEVICE_DATA(MOXA, CP118EL, 8) },
228 { PCI_DEVICE_DATA(MOXA, CP168EL, 8) },
229 { PCI_DEVICE_DATA(MOXA, CP104EL, 4) },
230 { PCI_DEVICE_DATA(MOXA, CB108, 8) },
231 { PCI_DEVICE_DATA(MOXA, CB114, 4) },
232 { PCI_DEVICE_DATA(MOXA, CB134I, 4) },
233 { PCI_DEVICE_DATA(MOXA, CP138U, 8) },
234 { PCI_DEVICE_DATA(MOXA, POS104UL, 4) },
235 { PCI_DEVICE_DATA(MOXA, CP114UL, 4) },
236 { PCI_DEVICE_DATA(MOXA, CP102UF, 2) },
237 { PCI_DEVICE_DATA(MOXA, CP112UL, 2) },
238 { }
239 };
240 MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
241
242 static int ttymajor = MXSERMAJOR;
243
244 /* Variables for insmod */
245
246 MODULE_AUTHOR("Casper Yang");
247 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
248 module_param(ttymajor, int, 0);
249 MODULE_LICENSE("GPL");
250
251 struct mxser_board;
252
253 struct mxser_port {
254 struct tty_port port;
255 struct mxser_board *board;
256
257 unsigned long ioaddr;
258 unsigned long opmode_ioaddr;
259
260 u8 rx_high_water;
261 u8 rx_low_water;
262 int type; /* UART type */
263
264 u8 x_char; /* xon/xoff character */
265 u8 IER; /* Interrupt Enable Register */
266 u8 MCR; /* Modem control register */
267 u8 FCR; /* FIFO control register */
268
269 struct async_icount icount; /* kernel counters for 4 input interrupts */
270 unsigned int timeout;
271
272 u8 read_status_mask;
273 u8 ignore_status_mask;
274 u8 xmit_fifo_size;
275
276 spinlock_t slock;
277 };
278
279 struct mxser_board {
280 unsigned int idx;
281 unsigned short nports;
282 int irq;
283 unsigned long vector;
284
285 enum mxser_must_hwid must_hwid;
286 speed_t max_baud;
287
288 struct mxser_port ports[] /* __counted_by(nports) */;
289 };
290
291 static DECLARE_BITMAP(mxser_boards, MXSER_BOARDS);
292 static struct tty_driver *mxvar_sdriver;
293
__mxser_must_set_EFR(unsigned long baseio,u8 clear,u8 set,bool restore_LCR)294 static u8 __mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set,
295 bool restore_LCR)
296 {
297 u8 oldlcr, efr;
298
299 oldlcr = inb(baseio + UART_LCR);
300 outb(MOXA_MUST_ENTER_ENHANCED, baseio + UART_LCR);
301
302 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
303 efr &= ~clear;
304 efr |= set;
305
306 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
307
308 if (restore_LCR)
309 outb(oldlcr, baseio + UART_LCR);
310
311 return oldlcr;
312 }
313
mxser_must_select_bank(unsigned long baseio,u8 bank)314 static u8 mxser_must_select_bank(unsigned long baseio, u8 bank)
315 {
316 return __mxser_must_set_EFR(baseio, MOXA_MUST_EFR_BANK_MASK, bank,
317 false);
318 }
319
mxser_set_must_xon1_value(unsigned long baseio,u8 value)320 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
321 {
322 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
323 outb(value, baseio + MOXA_MUST_XON1_REGISTER);
324 outb(oldlcr, baseio + UART_LCR);
325 }
326
mxser_set_must_xoff1_value(unsigned long baseio,u8 value)327 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
328 {
329 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
330 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
331 outb(oldlcr, baseio + UART_LCR);
332 }
333
mxser_set_must_fifo_value(struct mxser_port * info)334 static void mxser_set_must_fifo_value(struct mxser_port *info)
335 {
336 u8 oldlcr = mxser_must_select_bank(info->ioaddr, MOXA_MUST_EFR_BANK1);
337 outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
338 outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
339 outb(info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
340 outb(oldlcr, info->ioaddr + UART_LCR);
341 }
342
mxser_set_must_enum_value(unsigned long baseio,u8 value)343 static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
344 {
345 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
346 outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
347 outb(oldlcr, baseio + UART_LCR);
348 }
349
mxser_get_must_hardware_id(unsigned long baseio)350 static u8 mxser_get_must_hardware_id(unsigned long baseio)
351 {
352 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
353 u8 id = inb(baseio + MOXA_MUST_HWID_REGISTER);
354 outb(oldlcr, baseio + UART_LCR);
355
356 return id;
357 }
358
mxser_must_set_EFR(unsigned long baseio,u8 clear,u8 set)359 static void mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set)
360 {
361 __mxser_must_set_EFR(baseio, clear, set, true);
362 }
363
mxser_must_set_enhance_mode(unsigned long baseio,bool enable)364 static void mxser_must_set_enhance_mode(unsigned long baseio, bool enable)
365 {
366 mxser_must_set_EFR(baseio,
367 enable ? 0 : MOXA_MUST_EFR_EFRB_ENABLE,
368 enable ? MOXA_MUST_EFR_EFRB_ENABLE : 0);
369 }
370
mxser_must_no_sw_flow_control(unsigned long baseio)371 static void mxser_must_no_sw_flow_control(unsigned long baseio)
372 {
373 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_MASK, 0);
374 }
375
mxser_must_set_tx_sw_flow_control(unsigned long baseio,bool enable)376 static void mxser_must_set_tx_sw_flow_control(unsigned long baseio, bool enable)
377 {
378 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_TX_MASK,
379 enable ? MOXA_MUST_EFR_SF_TX1 : 0);
380 }
381
mxser_must_set_rx_sw_flow_control(unsigned long baseio,bool enable)382 static void mxser_must_set_rx_sw_flow_control(unsigned long baseio, bool enable)
383 {
384 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_RX_MASK,
385 enable ? MOXA_MUST_EFR_SF_RX1 : 0);
386 }
387
mxser_must_get_hwid(unsigned long io)388 static enum mxser_must_hwid mxser_must_get_hwid(unsigned long io)
389 {
390 u8 oldmcr, hwid;
391 int i;
392
393 outb(0, io + UART_LCR);
394 mxser_must_set_enhance_mode(io, false);
395 oldmcr = inb(io + UART_MCR);
396 outb(0, io + UART_MCR);
397 mxser_set_must_xon1_value(io, 0x11);
398 if (inb(io + UART_MCR) != 0) {
399 outb(oldmcr, io + UART_MCR);
400 return MOXA_OTHER_UART;
401 }
402
403 hwid = mxser_get_must_hardware_id(io);
404 for (i = 1; i < UART_INFO_NUM; i++) /* 0 = OTHER_UART */
405 if (hwid == Gpci_uart_info[i].type)
406 return hwid;
407
408 return MOXA_OTHER_UART;
409 }
410
mxser_16550A_or_MUST(struct mxser_port * info)411 static bool mxser_16550A_or_MUST(struct mxser_port *info)
412 {
413 return info->type == PORT_16550A || info->board->must_hwid;
414 }
415
mxser_process_txrx_fifo(struct mxser_port * info)416 static void mxser_process_txrx_fifo(struct mxser_port *info)
417 {
418 unsigned int i;
419
420 if (info->type == PORT_16450 || info->type == PORT_8250) {
421 info->rx_high_water = 1;
422 info->rx_low_water = 1;
423 info->xmit_fifo_size = 1;
424 return;
425 }
426
427 for (i = 0; i < UART_INFO_NUM; i++)
428 if (info->board->must_hwid == Gpci_uart_info[i].type) {
429 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
430 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
431 info->xmit_fifo_size = Gpci_uart_info[i].fifo_size;
432 break;
433 }
434 }
435
__mxser_start_tx(struct mxser_port * info)436 static void __mxser_start_tx(struct mxser_port *info)
437 {
438 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
439 info->IER |= UART_IER_THRI;
440 outb(info->IER, info->ioaddr + UART_IER);
441 }
442
mxser_start_tx(struct mxser_port * info)443 static void mxser_start_tx(struct mxser_port *info)
444 {
445 unsigned long flags;
446
447 spin_lock_irqsave(&info->slock, flags);
448 __mxser_start_tx(info);
449 spin_unlock_irqrestore(&info->slock, flags);
450 }
451
__mxser_stop_tx(struct mxser_port * info)452 static void __mxser_stop_tx(struct mxser_port *info)
453 {
454 info->IER &= ~UART_IER_THRI;
455 outb(info->IER, info->ioaddr + UART_IER);
456 }
457
mxser_carrier_raised(struct tty_port * port)458 static bool mxser_carrier_raised(struct tty_port *port)
459 {
460 struct mxser_port *mp = container_of(port, struct mxser_port, port);
461
462 return inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD;
463 }
464
mxser_dtr_rts(struct tty_port * port,bool active)465 static void mxser_dtr_rts(struct tty_port *port, bool active)
466 {
467 struct mxser_port *mp = container_of(port, struct mxser_port, port);
468 unsigned long flags;
469 u8 mcr;
470
471 spin_lock_irqsave(&mp->slock, flags);
472 mcr = inb(mp->ioaddr + UART_MCR);
473 if (active)
474 mcr |= UART_MCR_DTR | UART_MCR_RTS;
475 else
476 mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
477 outb(mcr, mp->ioaddr + UART_MCR);
478 spin_unlock_irqrestore(&mp->slock, flags);
479 }
480
mxser_set_baud(struct tty_struct * tty,speed_t newspd)481 static int mxser_set_baud(struct tty_struct *tty, speed_t newspd)
482 {
483 struct mxser_port *info = tty->driver_data;
484 unsigned int quot = 0, baud;
485 unsigned char cval;
486 u64 timeout;
487
488 if (newspd > info->board->max_baud)
489 return -1;
490
491 if (newspd == 134) {
492 quot = 2 * MXSER_BAUD_BASE / 269;
493 tty_encode_baud_rate(tty, 134, 134);
494 } else if (newspd) {
495 quot = MXSER_BAUD_BASE / newspd;
496 if (quot == 0)
497 quot = 1;
498 baud = MXSER_BAUD_BASE / quot;
499 tty_encode_baud_rate(tty, baud, baud);
500 } else {
501 quot = 0;
502 }
503
504 /*
505 * worst case (128 * 1000 * 10 * 18432) needs 35 bits, so divide in the
506 * u64 domain
507 */
508 timeout = (u64)info->xmit_fifo_size * HZ * 10 * quot;
509 do_div(timeout, MXSER_BAUD_BASE);
510 info->timeout = timeout + HZ / 50; /* Add .02 seconds of slop */
511
512 if (quot) {
513 info->MCR |= UART_MCR_DTR;
514 outb(info->MCR, info->ioaddr + UART_MCR);
515 } else {
516 info->MCR &= ~UART_MCR_DTR;
517 outb(info->MCR, info->ioaddr + UART_MCR);
518 return 0;
519 }
520
521 cval = inb(info->ioaddr + UART_LCR);
522
523 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
524
525 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
526 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
527 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
528
529 if (C_BAUD(tty) == BOTHER) {
530 quot = MXSER_BAUD_BASE % newspd;
531 quot *= 8;
532 if (quot % newspd > newspd / 2) {
533 quot /= newspd;
534 quot++;
535 } else
536 quot /= newspd;
537
538 mxser_set_must_enum_value(info->ioaddr, quot);
539 } else {
540 mxser_set_must_enum_value(info->ioaddr, 0);
541 }
542
543 return 0;
544 }
545
mxser_handle_cts(struct tty_struct * tty,struct mxser_port * info,u8 msr)546 static void mxser_handle_cts(struct tty_struct *tty, struct mxser_port *info,
547 u8 msr)
548 {
549 bool cts = msr & UART_MSR_CTS;
550
551 if (tty->hw_stopped) {
552 if (cts) {
553 tty->hw_stopped = false;
554
555 if (!mxser_16550A_or_MUST(info))
556 __mxser_start_tx(info);
557 tty_wakeup(tty);
558 }
559 return;
560 } else if (cts)
561 return;
562
563 tty->hw_stopped = true;
564 if (!mxser_16550A_or_MUST(info))
565 __mxser_stop_tx(info);
566 }
567
568 /*
569 * This routine is called to set the UART divisor registers to match
570 * the specified baud rate for a serial port.
571 */
mxser_change_speed(struct tty_struct * tty,const struct ktermios * old_termios)572 static void mxser_change_speed(struct tty_struct *tty,
573 const struct ktermios *old_termios)
574 {
575 struct mxser_port *info = tty->driver_data;
576 unsigned cflag, cval;
577
578 cflag = tty->termios.c_cflag;
579
580 if (mxser_set_baud(tty, tty_get_baud_rate(tty))) {
581 /* Use previous rate on a failure */
582 if (old_termios) {
583 speed_t baud = tty_termios_baud_rate(old_termios);
584 tty_encode_baud_rate(tty, baud, baud);
585 }
586 }
587
588 /* byte size and parity */
589 cval = UART_LCR_WLEN(tty_get_char_size(tty->termios.c_cflag));
590
591 if (cflag & CSTOPB)
592 cval |= UART_LCR_STOP;
593 if (cflag & PARENB)
594 cval |= UART_LCR_PARITY;
595 if (!(cflag & PARODD))
596 cval |= UART_LCR_EPAR;
597 if (cflag & CMSPAR)
598 cval |= UART_LCR_SPAR;
599
600 info->FCR = 0;
601 if (info->board->must_hwid) {
602 info->FCR |= UART_FCR_ENABLE_FIFO |
603 MOXA_MUST_FCR_GDA_MODE_ENABLE;
604 mxser_set_must_fifo_value(info);
605 } else if (info->type != PORT_8250 && info->type != PORT_16450) {
606 info->FCR |= UART_FCR_ENABLE_FIFO;
607 switch (info->rx_high_water) {
608 case 1:
609 info->FCR |= UART_FCR_TRIGGER_1;
610 break;
611 case 4:
612 info->FCR |= UART_FCR_TRIGGER_4;
613 break;
614 case 8:
615 info->FCR |= UART_FCR_TRIGGER_8;
616 break;
617 default:
618 info->FCR |= UART_FCR_TRIGGER_14;
619 break;
620 }
621 }
622
623 /* CTS flow control flag and modem status interrupts */
624 info->IER &= ~UART_IER_MSI;
625 info->MCR &= ~UART_MCR_AFE;
626 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
627 if (cflag & CRTSCTS) {
628 info->IER |= UART_IER_MSI;
629 if (mxser_16550A_or_MUST(info)) {
630 info->MCR |= UART_MCR_AFE;
631 } else {
632 mxser_handle_cts(tty, info,
633 inb(info->ioaddr + UART_MSR));
634 }
635 }
636 outb(info->MCR, info->ioaddr + UART_MCR);
637 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
638 if (~cflag & CLOCAL)
639 info->IER |= UART_IER_MSI;
640 outb(info->IER, info->ioaddr + UART_IER);
641
642 /*
643 * Set up parity check flag
644 */
645 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
646 if (I_INPCK(tty))
647 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
648 if (I_BRKINT(tty) || I_PARMRK(tty))
649 info->read_status_mask |= UART_LSR_BI;
650
651 info->ignore_status_mask = 0;
652
653 if (I_IGNBRK(tty)) {
654 info->ignore_status_mask |= UART_LSR_BI;
655 info->read_status_mask |= UART_LSR_BI;
656 /*
657 * If we're ignore parity and break indicators, ignore
658 * overruns too. (For real raw support).
659 */
660 if (I_IGNPAR(tty)) {
661 info->ignore_status_mask |=
662 UART_LSR_OE |
663 UART_LSR_PE |
664 UART_LSR_FE;
665 info->read_status_mask |=
666 UART_LSR_OE |
667 UART_LSR_PE |
668 UART_LSR_FE;
669 }
670 }
671 if (info->board->must_hwid) {
672 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
673 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
674 mxser_must_set_rx_sw_flow_control(info->ioaddr, I_IXON(tty));
675 mxser_must_set_tx_sw_flow_control(info->ioaddr, I_IXOFF(tty));
676 }
677
678
679 outb(info->FCR, info->ioaddr + UART_FCR);
680 outb(cval, info->ioaddr + UART_LCR);
681 }
682
mxser_check_modem_status(struct tty_struct * tty,struct mxser_port * port)683 static u8 mxser_check_modem_status(struct tty_struct *tty,
684 struct mxser_port *port)
685 {
686 u8 msr = inb(port->ioaddr + UART_MSR);
687
688 if (!(msr & UART_MSR_ANY_DELTA))
689 return msr;
690
691 /* update input line counters */
692 if (msr & UART_MSR_TERI)
693 port->icount.rng++;
694 if (msr & UART_MSR_DDSR)
695 port->icount.dsr++;
696 if (msr & UART_MSR_DDCD)
697 port->icount.dcd++;
698 if (msr & UART_MSR_DCTS)
699 port->icount.cts++;
700 wake_up_interruptible(&port->port.delta_msr_wait);
701
702 if (tty_port_check_carrier(&port->port) && (msr & UART_MSR_DDCD)) {
703 if (msr & UART_MSR_DCD)
704 wake_up_interruptible(&port->port.open_wait);
705 }
706
707 if (tty_port_cts_enabled(&port->port))
708 mxser_handle_cts(tty, port, msr);
709
710 return msr;
711 }
712
mxser_disable_and_clear_FIFO(struct mxser_port * info)713 static void mxser_disable_and_clear_FIFO(struct mxser_port *info)
714 {
715 u8 fcr = UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT;
716
717 if (info->board->must_hwid)
718 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
719
720 outb(fcr, info->ioaddr + UART_FCR);
721 }
722
mxser_activate(struct tty_port * port,struct tty_struct * tty)723 static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
724 {
725 struct mxser_port *info = container_of(port, struct mxser_port, port);
726 unsigned long flags;
727 int ret;
728
729 ret = tty_port_alloc_xmit_buf(port);
730 if (ret < 0)
731 return ret;
732
733 spin_lock_irqsave(&info->slock, flags);
734
735 if (!info->type) {
736 set_bit(TTY_IO_ERROR, &tty->flags);
737 spin_unlock_irqrestore(&info->slock, flags);
738 ret = 0;
739 goto err_free_xmit;
740 }
741
742 /*
743 * Clear the FIFO buffers and disable them
744 * (they will be reenabled in mxser_change_speed())
745 */
746 mxser_disable_and_clear_FIFO(info);
747
748 /*
749 * At this point there's no way the LSR could still be 0xFF;
750 * if it is, then bail out, because there's likely no UART
751 * here.
752 */
753 if (inb(info->ioaddr + UART_LSR) == 0xff) {
754 spin_unlock_irqrestore(&info->slock, flags);
755 if (capable(CAP_SYS_ADMIN)) {
756 set_bit(TTY_IO_ERROR, &tty->flags);
757 return 0;
758 }
759
760 ret = -ENODEV;
761 goto err_free_xmit;
762 }
763
764 /*
765 * Clear the interrupt registers.
766 */
767 (void) inb(info->ioaddr + UART_LSR);
768 (void) inb(info->ioaddr + UART_RX);
769 (void) inb(info->ioaddr + UART_IIR);
770 (void) inb(info->ioaddr + UART_MSR);
771
772 /*
773 * Now, initialize the UART
774 */
775 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
776 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
777 outb(info->MCR, info->ioaddr + UART_MCR);
778
779 /*
780 * Finally, enable interrupts
781 */
782 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
783
784 if (info->board->must_hwid)
785 info->IER |= MOXA_MUST_IER_EGDAI;
786 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
787
788 /*
789 * And clear the interrupt registers again for luck.
790 */
791 (void) inb(info->ioaddr + UART_LSR);
792 (void) inb(info->ioaddr + UART_RX);
793 (void) inb(info->ioaddr + UART_IIR);
794 (void) inb(info->ioaddr + UART_MSR);
795
796 clear_bit(TTY_IO_ERROR, &tty->flags);
797 kfifo_reset(&port->xmit_fifo);
798
799 /*
800 * and set the speed of the serial port
801 */
802 mxser_change_speed(tty, NULL);
803 spin_unlock_irqrestore(&info->slock, flags);
804
805 return 0;
806 err_free_xmit:
807 tty_port_free_xmit_buf(port);
808 return ret;
809 }
810
811 /*
812 * To stop accepting input, we disable the receive line status interrupts, and
813 * tell the interrupt driver to stop checking the data ready bit in the line
814 * status register.
815 */
mxser_stop_rx(struct mxser_port * info)816 static void mxser_stop_rx(struct mxser_port *info)
817 {
818 info->IER &= ~UART_IER_RLSI;
819 if (info->board->must_hwid)
820 info->IER &= ~MOXA_MUST_RECV_ISR;
821
822 outb(info->IER, info->ioaddr + UART_IER);
823 }
824
825 /*
826 * This routine will shutdown a serial port
827 */
mxser_shutdown_port(struct tty_port * port)828 static void mxser_shutdown_port(struct tty_port *port)
829 {
830 struct mxser_port *info = container_of(port, struct mxser_port, port);
831 unsigned long flags;
832
833 spin_lock_irqsave(&info->slock, flags);
834
835 mxser_stop_rx(info);
836
837 /*
838 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
839 * here so the queue might never be waken up
840 */
841 wake_up_interruptible(&info->port.delta_msr_wait);
842
843 info->IER = 0;
844 outb(0x00, info->ioaddr + UART_IER);
845
846 /* clear Rx/Tx FIFO's */
847 mxser_disable_and_clear_FIFO(info);
848
849 /* read data port to reset things */
850 (void) inb(info->ioaddr + UART_RX);
851
852
853 if (info->board->must_hwid)
854 mxser_must_no_sw_flow_control(info->ioaddr);
855
856 spin_unlock_irqrestore(&info->slock, flags);
857
858 /* make sure ISR is not running while we free the buffer */
859 synchronize_irq(info->board->irq);
860
861 tty_port_free_xmit_buf(port);
862 }
863
864 /*
865 * This routine is called whenever a serial port is opened. It
866 * enables interrupts for a serial port, linking in its async structure into
867 * the IRQ chain. It also performs the serial-specific
868 * initialization for the tty structure.
869 */
mxser_open(struct tty_struct * tty,struct file * filp)870 static int mxser_open(struct tty_struct *tty, struct file *filp)
871 {
872 struct tty_port *tport = tty->port;
873 struct mxser_port *port = container_of(tport, struct mxser_port, port);
874
875 tty->driver_data = port;
876
877 return tty_port_open(tport, tty, filp);
878 }
879
mxser_flush_buffer(struct tty_struct * tty)880 static void mxser_flush_buffer(struct tty_struct *tty)
881 {
882 struct mxser_port *info = tty->driver_data;
883 unsigned long flags;
884
885 spin_lock_irqsave(&info->slock, flags);
886 kfifo_reset(&info->port.xmit_fifo);
887
888 outb(info->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
889 info->ioaddr + UART_FCR);
890
891 spin_unlock_irqrestore(&info->slock, flags);
892
893 tty_wakeup(tty);
894 }
895
mxser_close(struct tty_struct * tty,struct file * filp)896 static void mxser_close(struct tty_struct *tty, struct file *filp)
897 {
898 tty_port_close(tty->port, tty, filp);
899 }
900
mxser_write(struct tty_struct * tty,const u8 * buf,size_t count)901 static ssize_t mxser_write(struct tty_struct *tty, const u8 *buf, size_t count)
902 {
903 struct mxser_port *info = tty->driver_data;
904 unsigned long flags;
905 size_t written;
906 bool is_empty;
907
908 spin_lock_irqsave(&info->slock, flags);
909 written = kfifo_in(&info->port.xmit_fifo, buf, count);
910 is_empty = kfifo_is_empty(&info->port.xmit_fifo);
911 spin_unlock_irqrestore(&info->slock, flags);
912
913 if (!is_empty && !tty->flow.stopped)
914 if (!tty->hw_stopped || mxser_16550A_or_MUST(info))
915 mxser_start_tx(info);
916
917 return written;
918 }
919
mxser_put_char(struct tty_struct * tty,u8 ch)920 static int mxser_put_char(struct tty_struct *tty, u8 ch)
921 {
922 struct mxser_port *info = tty->driver_data;
923 unsigned long flags;
924 int ret;
925
926 spin_lock_irqsave(&info->slock, flags);
927 ret = kfifo_put(&info->port.xmit_fifo, ch);
928 spin_unlock_irqrestore(&info->slock, flags);
929
930 return ret;
931 }
932
933
mxser_flush_chars(struct tty_struct * tty)934 static void mxser_flush_chars(struct tty_struct *tty)
935 {
936 struct mxser_port *info = tty->driver_data;
937
938 if (kfifo_is_empty(&info->port.xmit_fifo) || tty->flow.stopped ||
939 (tty->hw_stopped && !mxser_16550A_or_MUST(info)))
940 return;
941
942 mxser_start_tx(info);
943 }
944
mxser_write_room(struct tty_struct * tty)945 static unsigned int mxser_write_room(struct tty_struct *tty)
946 {
947 struct mxser_port *info = tty->driver_data;
948
949 return kfifo_avail(&info->port.xmit_fifo);
950 }
951
mxser_chars_in_buffer(struct tty_struct * tty)952 static unsigned int mxser_chars_in_buffer(struct tty_struct *tty)
953 {
954 struct mxser_port *info = tty->driver_data;
955
956 return kfifo_len(&info->port.xmit_fifo);
957 }
958
959 /*
960 * ------------------------------------------------------------
961 * friends of mxser_ioctl()
962 * ------------------------------------------------------------
963 */
mxser_get_serial_info(struct tty_struct * tty,struct serial_struct * ss)964 static int mxser_get_serial_info(struct tty_struct *tty,
965 struct serial_struct *ss)
966 {
967 struct mxser_port *info = tty->driver_data;
968 struct tty_port *port = &info->port;
969 unsigned int closing_wait, close_delay;
970
971 mutex_lock(&port->mutex);
972
973 close_delay = jiffies_to_msecs(info->port.close_delay) / 10;
974 closing_wait = info->port.closing_wait;
975 if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
976 closing_wait = jiffies_to_msecs(closing_wait) / 10;
977
978 ss->type = info->type;
979 ss->line = tty->index;
980 ss->port = info->ioaddr;
981 ss->irq = info->board->irq;
982 ss->flags = info->port.flags;
983 ss->baud_base = MXSER_BAUD_BASE;
984 ss->close_delay = close_delay;
985 ss->closing_wait = closing_wait;
986 ss->custom_divisor = MXSER_CUSTOM_DIVISOR;
987 mutex_unlock(&port->mutex);
988 return 0;
989 }
990
mxser_set_serial_info(struct tty_struct * tty,struct serial_struct * ss)991 static int mxser_set_serial_info(struct tty_struct *tty,
992 struct serial_struct *ss)
993 {
994 struct mxser_port *info = tty->driver_data;
995 struct tty_port *port = &info->port;
996 speed_t baud;
997 unsigned long sl_flags;
998 unsigned int old_speed, close_delay, closing_wait;
999 int retval = 0;
1000
1001 if (tty_io_error(tty))
1002 return -EIO;
1003
1004 mutex_lock(&port->mutex);
1005
1006 if (ss->irq != info->board->irq ||
1007 ss->port != info->ioaddr) {
1008 mutex_unlock(&port->mutex);
1009 return -EINVAL;
1010 }
1011
1012 old_speed = port->flags & ASYNC_SPD_MASK;
1013
1014 close_delay = msecs_to_jiffies(ss->close_delay * 10);
1015 closing_wait = ss->closing_wait;
1016 if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
1017 closing_wait = msecs_to_jiffies(closing_wait * 10);
1018
1019 if (!capable(CAP_SYS_ADMIN)) {
1020 if ((ss->baud_base != MXSER_BAUD_BASE) ||
1021 (close_delay != port->close_delay) ||
1022 (closing_wait != port->closing_wait) ||
1023 ((ss->flags & ~ASYNC_USR_MASK) != (port->flags & ~ASYNC_USR_MASK))) {
1024 mutex_unlock(&port->mutex);
1025 return -EPERM;
1026 }
1027 port->flags = (port->flags & ~ASYNC_USR_MASK) |
1028 (ss->flags & ASYNC_USR_MASK);
1029 } else {
1030 /*
1031 * OK, past this point, all the error checking has been done.
1032 * At this point, we start making changes.....
1033 */
1034 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1035 (ss->flags & ASYNC_FLAGS));
1036 port->close_delay = close_delay;
1037 port->closing_wait = closing_wait;
1038 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1039 (ss->baud_base != MXSER_BAUD_BASE ||
1040 ss->custom_divisor !=
1041 MXSER_CUSTOM_DIVISOR)) {
1042 if (ss->custom_divisor == 0) {
1043 mutex_unlock(&port->mutex);
1044 return -EINVAL;
1045 }
1046 baud = ss->baud_base / ss->custom_divisor;
1047 tty_encode_baud_rate(tty, baud, baud);
1048 }
1049
1050 info->type = ss->type;
1051
1052 mxser_process_txrx_fifo(info);
1053 }
1054
1055 if (tty_port_initialized(port)) {
1056 if (old_speed != (port->flags & ASYNC_SPD_MASK)) {
1057 spin_lock_irqsave(&info->slock, sl_flags);
1058 mxser_change_speed(tty, NULL);
1059 spin_unlock_irqrestore(&info->slock, sl_flags);
1060 }
1061 } else {
1062 retval = mxser_activate(port, tty);
1063 if (retval == 0)
1064 tty_port_set_initialized(port, true);
1065 }
1066 mutex_unlock(&port->mutex);
1067 return retval;
1068 }
1069
1070 /*
1071 * mxser_get_lsr_info - get line status register info
1072 *
1073 * Purpose: Let user call ioctl() to get info when the UART physically
1074 * is emptied. On bus types like RS485, the transmitter must
1075 * release the bus after transmitting. This must be done when
1076 * the transmit shift register is empty, not be done when the
1077 * transmit holding register is empty. This functionality
1078 * allows an RS485 driver to be written in user space.
1079 */
mxser_get_lsr_info(struct mxser_port * info,unsigned int __user * value)1080 static int mxser_get_lsr_info(struct mxser_port *info,
1081 unsigned int __user *value)
1082 {
1083 unsigned char status;
1084 unsigned int result;
1085 unsigned long flags;
1086
1087 spin_lock_irqsave(&info->slock, flags);
1088 status = inb(info->ioaddr + UART_LSR);
1089 spin_unlock_irqrestore(&info->slock, flags);
1090 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1091 return put_user(result, value);
1092 }
1093
mxser_tiocmget(struct tty_struct * tty)1094 static int mxser_tiocmget(struct tty_struct *tty)
1095 {
1096 struct mxser_port *info = tty->driver_data;
1097 unsigned char control;
1098 unsigned long flags;
1099 u8 msr;
1100
1101 if (tty_io_error(tty))
1102 return -EIO;
1103
1104 spin_lock_irqsave(&info->slock, flags);
1105 control = info->MCR;
1106 msr = mxser_check_modem_status(tty, info);
1107 spin_unlock_irqrestore(&info->slock, flags);
1108
1109 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1110 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1111 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1112 ((msr & UART_MSR_RI) ? TIOCM_RNG : 0) |
1113 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1114 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0);
1115 }
1116
mxser_tiocmset(struct tty_struct * tty,unsigned int set,unsigned int clear)1117 static int mxser_tiocmset(struct tty_struct *tty,
1118 unsigned int set, unsigned int clear)
1119 {
1120 struct mxser_port *info = tty->driver_data;
1121 unsigned long flags;
1122
1123 if (tty_io_error(tty))
1124 return -EIO;
1125
1126 spin_lock_irqsave(&info->slock, flags);
1127
1128 if (set & TIOCM_RTS)
1129 info->MCR |= UART_MCR_RTS;
1130 if (set & TIOCM_DTR)
1131 info->MCR |= UART_MCR_DTR;
1132
1133 if (clear & TIOCM_RTS)
1134 info->MCR &= ~UART_MCR_RTS;
1135 if (clear & TIOCM_DTR)
1136 info->MCR &= ~UART_MCR_DTR;
1137
1138 outb(info->MCR, info->ioaddr + UART_MCR);
1139 spin_unlock_irqrestore(&info->slock, flags);
1140 return 0;
1141 }
1142
mxser_cflags_changed(struct mxser_port * info,unsigned long arg,struct async_icount * cprev)1143 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1144 struct async_icount *cprev)
1145 {
1146 struct async_icount cnow;
1147 unsigned long flags;
1148 int ret;
1149
1150 spin_lock_irqsave(&info->slock, flags);
1151 cnow = info->icount; /* atomic copy */
1152 spin_unlock_irqrestore(&info->slock, flags);
1153
1154 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1155 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1156 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
1157 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1158
1159 *cprev = cnow;
1160
1161 return ret;
1162 }
1163
1164 /* We should likely switch to TIOCGRS485/TIOCSRS485. */
mxser_ioctl_op_mode(struct mxser_port * port,int index,bool set,int __user * u_opmode)1165 static int mxser_ioctl_op_mode(struct mxser_port *port, int index, bool set,
1166 int __user *u_opmode)
1167 {
1168 int opmode, p = index % 4;
1169 int shiftbit = p * 2;
1170 u8 val;
1171
1172 if (port->board->must_hwid != MOXA_MUST_MU860_HWID)
1173 return -EFAULT;
1174
1175 if (set) {
1176 if (get_user(opmode, u_opmode))
1177 return -EFAULT;
1178
1179 if (opmode & ~OP_MODE_MASK)
1180 return -EINVAL;
1181
1182 spin_lock_irq(&port->slock);
1183 val = inb(port->opmode_ioaddr);
1184 val &= ~(OP_MODE_MASK << shiftbit);
1185 val |= (opmode << shiftbit);
1186 outb(val, port->opmode_ioaddr);
1187 spin_unlock_irq(&port->slock);
1188
1189 return 0;
1190 }
1191
1192 spin_lock_irq(&port->slock);
1193 opmode = inb(port->opmode_ioaddr) >> shiftbit;
1194 spin_unlock_irq(&port->slock);
1195
1196 return put_user(opmode & OP_MODE_MASK, u_opmode);
1197 }
1198
mxser_ioctl(struct tty_struct * tty,unsigned int cmd,unsigned long arg)1199 static int mxser_ioctl(struct tty_struct *tty,
1200 unsigned int cmd, unsigned long arg)
1201 {
1202 struct mxser_port *info = tty->driver_data;
1203 struct async_icount cnow;
1204 unsigned long flags;
1205 void __user *argp = (void __user *)arg;
1206
1207 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE)
1208 return mxser_ioctl_op_mode(info, tty->index,
1209 cmd == MOXA_SET_OP_MODE, argp);
1210
1211 if (cmd != TIOCMIWAIT && tty_io_error(tty))
1212 return -EIO;
1213
1214 switch (cmd) {
1215 case TIOCSERGETLSR: /* Get line status register */
1216 return mxser_get_lsr_info(info, argp);
1217 /*
1218 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1219 * - mask passed in arg for lines of interest
1220 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1221 * Caller should use TIOCGICOUNT to see which one it was
1222 */
1223 case TIOCMIWAIT:
1224 spin_lock_irqsave(&info->slock, flags);
1225 cnow = info->icount; /* note the counters on entry */
1226 spin_unlock_irqrestore(&info->slock, flags);
1227
1228 return wait_event_interruptible(info->port.delta_msr_wait,
1229 mxser_cflags_changed(info, arg, &cnow));
1230 default:
1231 return -ENOIOCTLCMD;
1232 }
1233 return 0;
1234 }
1235
1236 /*
1237 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1238 * Return: write counters to the user passed counter struct
1239 * NB: both 1->0 and 0->1 transitions are counted except for
1240 * RI where only 0->1 is counted.
1241 */
1242
mxser_get_icount(struct tty_struct * tty,struct serial_icounter_struct * icount)1243 static int mxser_get_icount(struct tty_struct *tty,
1244 struct serial_icounter_struct *icount)
1245
1246 {
1247 struct mxser_port *info = tty->driver_data;
1248 struct async_icount cnow;
1249 unsigned long flags;
1250
1251 spin_lock_irqsave(&info->slock, flags);
1252 cnow = info->icount;
1253 spin_unlock_irqrestore(&info->slock, flags);
1254
1255 icount->frame = cnow.frame;
1256 icount->brk = cnow.brk;
1257 icount->overrun = cnow.overrun;
1258 icount->buf_overrun = cnow.buf_overrun;
1259 icount->parity = cnow.parity;
1260 icount->rx = cnow.rx;
1261 icount->tx = cnow.tx;
1262 icount->cts = cnow.cts;
1263 icount->dsr = cnow.dsr;
1264 icount->rng = cnow.rng;
1265 icount->dcd = cnow.dcd;
1266 return 0;
1267 }
1268
1269 /*
1270 * This routine is called by the upper-layer tty layer to signal that
1271 * incoming characters should be throttled.
1272 */
mxser_throttle(struct tty_struct * tty)1273 static void mxser_throttle(struct tty_struct *tty)
1274 {
1275 struct mxser_port *info = tty->driver_data;
1276
1277 if (I_IXOFF(tty)) {
1278 if (info->board->must_hwid) {
1279 info->IER &= ~MOXA_MUST_RECV_ISR;
1280 outb(info->IER, info->ioaddr + UART_IER);
1281 } else {
1282 info->x_char = STOP_CHAR(tty);
1283 outb(0, info->ioaddr + UART_IER);
1284 info->IER |= UART_IER_THRI;
1285 outb(info->IER, info->ioaddr + UART_IER);
1286 }
1287 }
1288
1289 if (C_CRTSCTS(tty)) {
1290 info->MCR &= ~UART_MCR_RTS;
1291 outb(info->MCR, info->ioaddr + UART_MCR);
1292 }
1293 }
1294
mxser_unthrottle(struct tty_struct * tty)1295 static void mxser_unthrottle(struct tty_struct *tty)
1296 {
1297 struct mxser_port *info = tty->driver_data;
1298
1299 /* startrx */
1300 if (I_IXOFF(tty)) {
1301 if (info->x_char)
1302 info->x_char = 0;
1303 else {
1304 if (info->board->must_hwid) {
1305 info->IER |= MOXA_MUST_RECV_ISR;
1306 outb(info->IER, info->ioaddr + UART_IER);
1307 } else {
1308 info->x_char = START_CHAR(tty);
1309 outb(0, info->ioaddr + UART_IER);
1310 info->IER |= UART_IER_THRI;
1311 outb(info->IER, info->ioaddr + UART_IER);
1312 }
1313 }
1314 }
1315
1316 if (C_CRTSCTS(tty)) {
1317 info->MCR |= UART_MCR_RTS;
1318 outb(info->MCR, info->ioaddr + UART_MCR);
1319 }
1320 }
1321
1322 /*
1323 * mxser_stop() and mxser_start()
1324 *
1325 * This routines are called before setting or resetting tty->flow.stopped.
1326 * They enable or disable transmitter interrupts, as necessary.
1327 */
mxser_stop(struct tty_struct * tty)1328 static void mxser_stop(struct tty_struct *tty)
1329 {
1330 struct mxser_port *info = tty->driver_data;
1331 unsigned long flags;
1332
1333 spin_lock_irqsave(&info->slock, flags);
1334 if (info->IER & UART_IER_THRI)
1335 __mxser_stop_tx(info);
1336 spin_unlock_irqrestore(&info->slock, flags);
1337 }
1338
mxser_start(struct tty_struct * tty)1339 static void mxser_start(struct tty_struct *tty)
1340 {
1341 struct mxser_port *info = tty->driver_data;
1342 unsigned long flags;
1343
1344 spin_lock_irqsave(&info->slock, flags);
1345 if (!kfifo_is_empty(&info->port.xmit_fifo))
1346 __mxser_start_tx(info);
1347 spin_unlock_irqrestore(&info->slock, flags);
1348 }
1349
mxser_set_termios(struct tty_struct * tty,const struct ktermios * old_termios)1350 static void mxser_set_termios(struct tty_struct *tty,
1351 const struct ktermios *old_termios)
1352 {
1353 struct mxser_port *info = tty->driver_data;
1354 unsigned long flags;
1355
1356 spin_lock_irqsave(&info->slock, flags);
1357 mxser_change_speed(tty, old_termios);
1358 spin_unlock_irqrestore(&info->slock, flags);
1359
1360 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
1361 tty->hw_stopped = false;
1362 mxser_start(tty);
1363 }
1364
1365 /* Handle sw stopped */
1366 if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) {
1367 tty->flow.stopped = 0;
1368
1369 if (info->board->must_hwid) {
1370 spin_lock_irqsave(&info->slock, flags);
1371 mxser_must_set_rx_sw_flow_control(info->ioaddr, false);
1372 spin_unlock_irqrestore(&info->slock, flags);
1373 }
1374
1375 mxser_start(tty);
1376 }
1377 }
1378
mxser_tx_empty(struct mxser_port * info)1379 static bool mxser_tx_empty(struct mxser_port *info)
1380 {
1381 unsigned long flags;
1382 u8 lsr;
1383
1384 spin_lock_irqsave(&info->slock, flags);
1385 lsr = inb(info->ioaddr + UART_LSR);
1386 spin_unlock_irqrestore(&info->slock, flags);
1387
1388 return !(lsr & UART_LSR_TEMT);
1389 }
1390
1391 /*
1392 * mxser_wait_until_sent() --- wait until the transmitter is empty
1393 */
mxser_wait_until_sent(struct tty_struct * tty,int timeout)1394 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1395 {
1396 struct mxser_port *info = tty->driver_data;
1397 unsigned long expire, char_time;
1398
1399 if (info->type == PORT_UNKNOWN)
1400 return;
1401
1402 if (info->xmit_fifo_size == 0)
1403 return; /* Just in case.... */
1404
1405 /*
1406 * Set the check interval to be 1/5 of the estimated time to
1407 * send a single character, and make it at least 1. The check
1408 * interval should also be less than the timeout.
1409 *
1410 * Note: we have to use pretty tight timings here to satisfy
1411 * the NIST-PCTS.
1412 */
1413 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1414 char_time = char_time / 5;
1415 if (char_time == 0)
1416 char_time = 1;
1417 if (timeout && timeout < char_time)
1418 char_time = timeout;
1419
1420 char_time = jiffies_to_msecs(char_time);
1421
1422 /*
1423 * If the transmitter hasn't cleared in twice the approximate
1424 * amount of time to send the entire FIFO, it probably won't
1425 * ever clear. This assumes the UART isn't doing flow
1426 * control, which is currently the case. Hence, if it ever
1427 * takes longer than info->timeout, this is probably due to a
1428 * UART bug of some kind. So, we clamp the timeout parameter at
1429 * 2*info->timeout.
1430 */
1431 if (!timeout || timeout > 2 * info->timeout)
1432 timeout = 2 * info->timeout;
1433
1434 expire = jiffies + timeout;
1435
1436 while (mxser_tx_empty(info)) {
1437 msleep_interruptible(char_time);
1438 if (signal_pending(current))
1439 break;
1440 if (time_after(jiffies, expire))
1441 break;
1442 }
1443 }
1444
1445 /*
1446 * This routine is called by tty_hangup() when a hangup is signaled.
1447 */
mxser_hangup(struct tty_struct * tty)1448 static void mxser_hangup(struct tty_struct *tty)
1449 {
1450 struct mxser_port *info = tty->driver_data;
1451
1452 mxser_flush_buffer(tty);
1453 tty_port_hangup(&info->port);
1454 }
1455
1456 /*
1457 * mxser_rs_break() --- routine which turns the break handling on or off
1458 */
mxser_rs_break(struct tty_struct * tty,int break_state)1459 static int mxser_rs_break(struct tty_struct *tty, int break_state)
1460 {
1461 struct mxser_port *info = tty->driver_data;
1462 unsigned long flags;
1463 u8 lcr;
1464
1465 spin_lock_irqsave(&info->slock, flags);
1466 lcr = inb(info->ioaddr + UART_LCR);
1467 if (break_state == -1)
1468 lcr |= UART_LCR_SBC;
1469 else
1470 lcr &= ~UART_LCR_SBC;
1471 outb(lcr, info->ioaddr + UART_LCR);
1472 spin_unlock_irqrestore(&info->slock, flags);
1473
1474 return 0;
1475 }
1476
mxser_receive_chars_new(struct mxser_port * port,u8 status)1477 static bool mxser_receive_chars_new(struct mxser_port *port, u8 status)
1478 {
1479 enum mxser_must_hwid hwid = port->board->must_hwid;
1480 u8 gdl;
1481
1482 if (hwid == MOXA_OTHER_UART)
1483 return false;
1484 if (status & (UART_LSR_BRK_ERROR_BITS | MOXA_MUST_LSR_RERR))
1485 return false;
1486
1487 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
1488 if (hwid == MOXA_MUST_MU150_HWID)
1489 gdl &= MOXA_MUST_GDL_MASK;
1490
1491 while (gdl--) {
1492 u8 ch = inb(port->ioaddr + UART_RX);
1493 if (!tty_insert_flip_char(&port->port, ch, 0))
1494 port->icount.buf_overrun++;
1495 }
1496
1497 return true;
1498 }
1499
mxser_receive_chars_old(struct tty_struct * tty,struct mxser_port * port,u8 status)1500 static u8 mxser_receive_chars_old(struct tty_struct *tty,
1501 struct mxser_port *port, u8 status)
1502 {
1503 enum mxser_must_hwid hwid = port->board->must_hwid;
1504 int ignored = 0;
1505 int max = 256;
1506 u8 ch;
1507
1508 do {
1509 if (max-- < 0)
1510 break;
1511
1512 ch = inb(port->ioaddr + UART_RX);
1513 if (hwid && (status & UART_LSR_OE))
1514 outb(port->FCR | UART_FCR_CLEAR_RCVR,
1515 port->ioaddr + UART_FCR);
1516 status &= port->read_status_mask;
1517 if (status & port->ignore_status_mask) {
1518 if (++ignored > 100)
1519 break;
1520 } else {
1521 u8 flag = 0;
1522 if (status & UART_LSR_BRK_ERROR_BITS) {
1523 if (status & UART_LSR_BI) {
1524 flag = TTY_BREAK;
1525 port->icount.brk++;
1526
1527 if (port->port.flags & ASYNC_SAK)
1528 do_SAK(tty);
1529 } else if (status & UART_LSR_PE) {
1530 flag = TTY_PARITY;
1531 port->icount.parity++;
1532 } else if (status & UART_LSR_FE) {
1533 flag = TTY_FRAME;
1534 port->icount.frame++;
1535 } else if (status & UART_LSR_OE) {
1536 flag = TTY_OVERRUN;
1537 port->icount.overrun++;
1538 }
1539 }
1540 if (!tty_insert_flip_char(&port->port, ch, flag)) {
1541 port->icount.buf_overrun++;
1542 break;
1543 }
1544 }
1545
1546 if (hwid)
1547 break;
1548
1549 status = inb(port->ioaddr + UART_LSR);
1550 } while (status & UART_LSR_DR);
1551
1552 return status;
1553 }
1554
mxser_receive_chars(struct tty_struct * tty,struct mxser_port * port,u8 status)1555 static u8 mxser_receive_chars(struct tty_struct *tty,
1556 struct mxser_port *port, u8 status)
1557 {
1558 if (!mxser_receive_chars_new(port, status))
1559 status = mxser_receive_chars_old(tty, port, status);
1560
1561 tty_flip_buffer_push(&port->port);
1562
1563 return status;
1564 }
1565
mxser_transmit_chars(struct tty_struct * tty,struct mxser_port * port)1566 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
1567 {
1568 int count;
1569
1570 if (port->x_char) {
1571 outb(port->x_char, port->ioaddr + UART_TX);
1572 port->x_char = 0;
1573 port->icount.tx++;
1574 return;
1575 }
1576
1577 if (kfifo_is_empty(&port->port.xmit_fifo) || tty->flow.stopped ||
1578 (tty->hw_stopped && !mxser_16550A_or_MUST(port))) {
1579 __mxser_stop_tx(port);
1580 return;
1581 }
1582
1583 count = port->xmit_fifo_size;
1584 do {
1585 u8 c;
1586
1587 if (!kfifo_get(&port->port.xmit_fifo, &c))
1588 break;
1589
1590 outb(c, port->ioaddr + UART_TX);
1591 port->icount.tx++;
1592 } while (--count > 0);
1593
1594 if (kfifo_len(&port->port.xmit_fifo) < WAKEUP_CHARS)
1595 tty_wakeup(tty);
1596
1597 if (kfifo_is_empty(&port->port.xmit_fifo))
1598 __mxser_stop_tx(port);
1599 }
1600
mxser_port_isr(struct mxser_port * port)1601 static bool mxser_port_isr(struct mxser_port *port)
1602 {
1603 struct tty_struct *tty;
1604 u8 iir, status;
1605 bool error = false;
1606
1607 iir = inb(port->ioaddr + UART_IIR);
1608 if (iir & UART_IIR_NO_INT)
1609 return true;
1610
1611 iir &= MOXA_MUST_IIR_MASK;
1612 tty = tty_port_tty_get(&port->port);
1613 if (!tty) {
1614 status = inb(port->ioaddr + UART_LSR);
1615 outb(port->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
1616 port->ioaddr + UART_FCR);
1617 inb(port->ioaddr + UART_MSR);
1618
1619 error = true;
1620 goto put_tty;
1621 }
1622
1623 status = inb(port->ioaddr + UART_LSR);
1624
1625 if (port->board->must_hwid) {
1626 if (iir == MOXA_MUST_IIR_GDA ||
1627 iir == MOXA_MUST_IIR_RDA ||
1628 iir == MOXA_MUST_IIR_RTO ||
1629 iir == MOXA_MUST_IIR_LSR)
1630 status = mxser_receive_chars(tty, port, status);
1631 } else {
1632 status &= port->read_status_mask;
1633 if (status & UART_LSR_DR)
1634 status = mxser_receive_chars(tty, port, status);
1635 }
1636
1637 mxser_check_modem_status(tty, port);
1638
1639 if (port->board->must_hwid) {
1640 if (iir == 0x02 && (status & UART_LSR_THRE))
1641 mxser_transmit_chars(tty, port);
1642 } else {
1643 if (status & UART_LSR_THRE)
1644 mxser_transmit_chars(tty, port);
1645 }
1646
1647 put_tty:
1648 tty_kref_put(tty);
1649
1650 return error;
1651 }
1652
1653 /*
1654 * This is the serial driver's generic interrupt routine
1655 */
mxser_interrupt(int irq,void * dev_id)1656 static irqreturn_t mxser_interrupt(int irq, void *dev_id)
1657 {
1658 struct mxser_board *brd = dev_id;
1659 struct mxser_port *port;
1660 unsigned int int_cnt, pass_counter = 0;
1661 unsigned int i, max = brd->nports;
1662 int handled = IRQ_NONE;
1663 u8 irqbits, bits, mask = BIT(max) - 1;
1664
1665 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
1666 irqbits = inb(brd->vector) & mask;
1667 if (irqbits == mask)
1668 break;
1669
1670 handled = IRQ_HANDLED;
1671 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
1672 if (irqbits == mask)
1673 break;
1674 if (bits & irqbits)
1675 continue;
1676 port = &brd->ports[i];
1677
1678 int_cnt = 0;
1679 spin_lock(&port->slock);
1680 do {
1681 if (mxser_port_isr(port))
1682 break;
1683 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
1684 spin_unlock(&port->slock);
1685 }
1686 }
1687
1688 return handled;
1689 }
1690
1691 static const struct tty_operations mxser_ops = {
1692 .open = mxser_open,
1693 .close = mxser_close,
1694 .write = mxser_write,
1695 .put_char = mxser_put_char,
1696 .flush_chars = mxser_flush_chars,
1697 .write_room = mxser_write_room,
1698 .chars_in_buffer = mxser_chars_in_buffer,
1699 .flush_buffer = mxser_flush_buffer,
1700 .ioctl = mxser_ioctl,
1701 .throttle = mxser_throttle,
1702 .unthrottle = mxser_unthrottle,
1703 .set_termios = mxser_set_termios,
1704 .stop = mxser_stop,
1705 .start = mxser_start,
1706 .hangup = mxser_hangup,
1707 .break_ctl = mxser_rs_break,
1708 .wait_until_sent = mxser_wait_until_sent,
1709 .tiocmget = mxser_tiocmget,
1710 .tiocmset = mxser_tiocmset,
1711 .set_serial = mxser_set_serial_info,
1712 .get_serial = mxser_get_serial_info,
1713 .get_icount = mxser_get_icount,
1714 };
1715
1716 static const struct tty_port_operations mxser_port_ops = {
1717 .carrier_raised = mxser_carrier_raised,
1718 .dtr_rts = mxser_dtr_rts,
1719 .activate = mxser_activate,
1720 .shutdown = mxser_shutdown_port,
1721 };
1722
1723 /*
1724 * The MOXA Smartio/Industio serial driver boot-time initialization code!
1725 */
1726
mxser_initbrd(struct mxser_board * brd,bool high_baud)1727 static void mxser_initbrd(struct mxser_board *brd, bool high_baud)
1728 {
1729 struct mxser_port *info;
1730 unsigned int i;
1731 bool is_mu860;
1732
1733 brd->must_hwid = mxser_must_get_hwid(brd->ports[0].ioaddr);
1734 is_mu860 = brd->must_hwid == MOXA_MUST_MU860_HWID;
1735
1736 for (i = 0; i < UART_INFO_NUM; i++) {
1737 if (Gpci_uart_info[i].type == brd->must_hwid) {
1738 brd->max_baud = Gpci_uart_info[i].max_baud;
1739
1740 /* exception....CP-102 */
1741 if (high_baud)
1742 brd->max_baud = 921600;
1743 break;
1744 }
1745 }
1746
1747 if (is_mu860) {
1748 /* set to RS232 mode by default */
1749 outb(0, brd->vector + 4);
1750 outb(0, brd->vector + 0x0c);
1751 }
1752
1753 for (i = 0; i < brd->nports; i++) {
1754 info = &brd->ports[i];
1755 if (is_mu860) {
1756 if (i < 4)
1757 info->opmode_ioaddr = brd->vector + 4;
1758 else
1759 info->opmode_ioaddr = brd->vector + 0x0c;
1760 }
1761 tty_port_init(&info->port);
1762 info->port.ops = &mxser_port_ops;
1763 info->board = brd;
1764
1765 /* Enhance mode enabled here */
1766 if (brd->must_hwid != MOXA_OTHER_UART)
1767 mxser_must_set_enhance_mode(info->ioaddr, true);
1768
1769 info->type = PORT_16550A;
1770
1771 mxser_process_txrx_fifo(info);
1772
1773 spin_lock_init(&info->slock);
1774
1775 /* before set INT ISR, disable all int */
1776 outb(inb(info->ioaddr + UART_IER) & 0xf0,
1777 info->ioaddr + UART_IER);
1778 }
1779 }
1780
mxser_probe(struct pci_dev * pdev,const struct pci_device_id * ent)1781 static int mxser_probe(struct pci_dev *pdev,
1782 const struct pci_device_id *ent)
1783 {
1784 struct mxser_board *brd;
1785 unsigned int i, base;
1786 unsigned long ioaddress;
1787 unsigned short nports = MXSER_NPORTS(ent->driver_data);
1788 struct device *tty_dev;
1789 int retval = -EINVAL;
1790
1791 i = find_first_zero_bit(mxser_boards, MXSER_BOARDS);
1792 if (i >= MXSER_BOARDS) {
1793 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
1794 "not configured\n", MXSER_BOARDS);
1795 goto err;
1796 }
1797
1798 brd = devm_kzalloc(&pdev->dev, struct_size(brd, ports, nports),
1799 GFP_KERNEL);
1800 if (!brd)
1801 goto err;
1802
1803 brd->idx = i;
1804 __set_bit(brd->idx, mxser_boards);
1805 base = i * MXSER_PORTS_PER_BOARD;
1806
1807 retval = pcim_enable_device(pdev);
1808 if (retval) {
1809 dev_err(&pdev->dev, "PCI enable failed\n");
1810 goto err_zero;
1811 }
1812
1813 /* io address */
1814 ioaddress = pci_resource_start(pdev, 2);
1815 retval = pci_request_region(pdev, 2, "mxser(IO)");
1816 if (retval)
1817 goto err_zero;
1818
1819 brd->nports = nports;
1820 for (i = 0; i < nports; i++)
1821 brd->ports[i].ioaddr = ioaddress + 8 * i;
1822
1823 /* vector */
1824 ioaddress = pci_resource_start(pdev, 3);
1825 retval = pci_request_region(pdev, 3, "mxser(vector)");
1826 if (retval)
1827 goto err_zero;
1828 brd->vector = ioaddress;
1829
1830 /* irq */
1831 brd->irq = pdev->irq;
1832
1833 mxser_initbrd(brd, ent->driver_data & MXSER_HIGHBAUD);
1834
1835 retval = devm_request_irq(&pdev->dev, brd->irq, mxser_interrupt,
1836 IRQF_SHARED, "mxser", brd);
1837 if (retval) {
1838 dev_err(&pdev->dev, "request irq failed");
1839 goto err_relbrd;
1840 }
1841
1842 for (i = 0; i < nports; i++) {
1843 tty_dev = tty_port_register_device(&brd->ports[i].port,
1844 mxvar_sdriver, base + i, &pdev->dev);
1845 if (IS_ERR(tty_dev)) {
1846 retval = PTR_ERR(tty_dev);
1847 for (; i > 0; i--)
1848 tty_unregister_device(mxvar_sdriver,
1849 base + i - 1);
1850 goto err_relbrd;
1851 }
1852 }
1853
1854 pci_set_drvdata(pdev, brd);
1855
1856 return 0;
1857 err_relbrd:
1858 for (i = 0; i < nports; i++)
1859 tty_port_destroy(&brd->ports[i].port);
1860 err_zero:
1861 __clear_bit(brd->idx, mxser_boards);
1862 err:
1863 return retval;
1864 }
1865
mxser_remove(struct pci_dev * pdev)1866 static void mxser_remove(struct pci_dev *pdev)
1867 {
1868 struct mxser_board *brd = pci_get_drvdata(pdev);
1869 unsigned int i, base = brd->idx * MXSER_PORTS_PER_BOARD;
1870
1871 for (i = 0; i < brd->nports; i++) {
1872 tty_unregister_device(mxvar_sdriver, base + i);
1873 tty_port_destroy(&brd->ports[i].port);
1874 }
1875
1876 __clear_bit(brd->idx, mxser_boards);
1877 }
1878
1879 static struct pci_driver mxser_driver = {
1880 .name = "mxser",
1881 .id_table = mxser_pcibrds,
1882 .probe = mxser_probe,
1883 .remove = mxser_remove
1884 };
1885
mxser_module_init(void)1886 static int __init mxser_module_init(void)
1887 {
1888 int retval;
1889
1890 mxvar_sdriver = tty_alloc_driver(MXSER_PORTS, TTY_DRIVER_REAL_RAW |
1891 TTY_DRIVER_DYNAMIC_DEV);
1892 if (IS_ERR(mxvar_sdriver))
1893 return PTR_ERR(mxvar_sdriver);
1894
1895 /* Initialize the tty_driver structure */
1896 mxvar_sdriver->name = "ttyMI";
1897 mxvar_sdriver->major = ttymajor;
1898 mxvar_sdriver->minor_start = 0;
1899 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
1900 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
1901 mxvar_sdriver->init_termios = tty_std_termios;
1902 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
1903 tty_set_operations(mxvar_sdriver, &mxser_ops);
1904
1905 retval = tty_register_driver(mxvar_sdriver);
1906 if (retval) {
1907 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
1908 "tty driver !\n");
1909 goto err_put;
1910 }
1911
1912 retval = pci_register_driver(&mxser_driver);
1913 if (retval) {
1914 printk(KERN_ERR "mxser: can't register pci driver\n");
1915 goto err_unr;
1916 }
1917
1918 return 0;
1919 err_unr:
1920 tty_unregister_driver(mxvar_sdriver);
1921 err_put:
1922 tty_driver_kref_put(mxvar_sdriver);
1923 return retval;
1924 }
1925
mxser_module_exit(void)1926 static void __exit mxser_module_exit(void)
1927 {
1928 pci_unregister_driver(&mxser_driver);
1929 tty_unregister_driver(mxvar_sdriver);
1930 tty_driver_kref_put(mxvar_sdriver);
1931 }
1932
1933 module_init(mxser_module_init);
1934 module_exit(mxser_module_exit);
1935