1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2008 Per Dalen <per.dalen@cnw.se>
4 *
5 * Parts of this software are based on (derived) the following:
6 *
7 * - Kvaser linux driver, version 4.72 BETA
8 * Copyright (C) 2002-2007 KVASER AB
9 *
10 * - Lincan driver, version 0.3.3, OCERA project
11 * Copyright (C) 2004 Pavel Pisa
12 * Copyright (C) 2001 Arnaud Westenberg
13 *
14 * - Socketcan SJA1000 drivers
15 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
16 * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
17 * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
18 * 38106 Braunschweig, GERMANY
19 */
20
21 #include <linux/kernel.h>
22 #include <linux/module.h>
23 #include <linux/interrupt.h>
24 #include <linux/netdevice.h>
25 #include <linux/delay.h>
26 #include <linux/pci.h>
27 #include <linux/can/dev.h>
28 #include <linux/io.h>
29
30 #include "sja1000.h"
31
32 #define DRV_NAME "kvaser_pci"
33
34 MODULE_AUTHOR("Per Dalen <per.dalen@cnw.se>");
35 MODULE_DESCRIPTION("Socket-CAN driver for KVASER PCAN PCI cards");
36 MODULE_LICENSE("GPL v2");
37
38 #define MAX_NO_OF_CHANNELS 4 /* max no of channels on a single card */
39
40 struct kvaser_pci {
41 int channel;
42 struct pci_dev *pci_dev;
43 struct net_device *slave_dev[MAX_NO_OF_CHANNELS-1];
44 void __iomem *conf_addr;
45 void __iomem *res_addr;
46 int no_channels;
47 u8 xilinx_ver;
48 };
49
50 #define KVASER_PCI_CAN_CLOCK (16000000 / 2)
51
52 /*
53 * The board configuration is probably following:
54 * RX1 is connected to ground.
55 * TX1 is not connected.
56 * CLKO is not connected.
57 * Setting the OCR register to 0xDA is a good idea.
58 * This means normal output mode , push-pull and the correct polarity.
59 */
60 #define KVASER_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
61
62 /*
63 * In the CDR register, you should set CBP to 1.
64 * You will probably also want to set the clock divider value to 0
65 * (meaning divide-by-2), the Pelican bit, and the clock-off bit
66 * (you will have no need for CLKOUT anyway).
67 */
68 #define KVASER_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
69
70 /*
71 * These register values are valid for revision 14 of the Xilinx logic.
72 */
73 #define XILINX_VERINT 7 /* Lower nibble simulate interrupts,
74 high nibble version number. */
75
76 #define XILINX_PRESUMED_VERSION 14
77
78 /*
79 * Important S5920 registers
80 */
81 #define S5920_INTCSR 0x38
82 #define S5920_PTCR 0x60
83 #define INTCSR_ADDON_INTENABLE_M 0x2000
84
85
86 #define KVASER_PCI_PORT_BYTES 0x20
87
88 #define PCI_CONFIG_PORT_SIZE 0x80 /* size of the config io-memory */
89 #define PCI_PORT_SIZE 0x80 /* size of a channel io-memory */
90 #define PCI_PORT_XILINX_SIZE 0x08 /* size of a xilinx io-memory */
91
92 #define KVASER_PCI_VENDOR_ID1 0x10e8 /* the PCI device and vendor IDs */
93 #define KVASER_PCI_DEVICE_ID1 0x8406
94
95 #define KVASER_PCI_VENDOR_ID2 0x1a07 /* the PCI device and vendor IDs */
96 #define KVASER_PCI_DEVICE_ID2 0x0008
97
98 static const struct pci_device_id kvaser_pci_tbl[] = {
99 {KVASER_PCI_VENDOR_ID1, KVASER_PCI_DEVICE_ID1, PCI_ANY_ID, PCI_ANY_ID,},
100 {KVASER_PCI_VENDOR_ID2, KVASER_PCI_DEVICE_ID2, PCI_ANY_ID, PCI_ANY_ID,},
101 { 0,}
102 };
103
104 MODULE_DEVICE_TABLE(pci, kvaser_pci_tbl);
105
kvaser_pci_read_reg(const struct sja1000_priv * priv,int port)106 static u8 kvaser_pci_read_reg(const struct sja1000_priv *priv, int port)
107 {
108 return ioread8(priv->reg_base + port);
109 }
110
kvaser_pci_write_reg(const struct sja1000_priv * priv,int port,u8 val)111 static void kvaser_pci_write_reg(const struct sja1000_priv *priv,
112 int port, u8 val)
113 {
114 iowrite8(val, priv->reg_base + port);
115 }
116
kvaser_pci_disable_irq(struct net_device * dev)117 static void kvaser_pci_disable_irq(struct net_device *dev)
118 {
119 struct sja1000_priv *priv = netdev_priv(dev);
120 struct kvaser_pci *board = priv->priv;
121 u32 intcsr;
122
123 /* Disable interrupts from card */
124 intcsr = ioread32(board->conf_addr + S5920_INTCSR);
125 intcsr &= ~INTCSR_ADDON_INTENABLE_M;
126 iowrite32(intcsr, board->conf_addr + S5920_INTCSR);
127 }
128
kvaser_pci_enable_irq(struct net_device * dev)129 static void kvaser_pci_enable_irq(struct net_device *dev)
130 {
131 struct sja1000_priv *priv = netdev_priv(dev);
132 struct kvaser_pci *board = priv->priv;
133 u32 tmp_en_io;
134
135 /* Enable interrupts from card */
136 tmp_en_io = ioread32(board->conf_addr + S5920_INTCSR);
137 tmp_en_io |= INTCSR_ADDON_INTENABLE_M;
138 iowrite32(tmp_en_io, board->conf_addr + S5920_INTCSR);
139 }
140
number_of_sja1000_chip(void __iomem * base_addr)141 static int number_of_sja1000_chip(void __iomem *base_addr)
142 {
143 u8 status;
144 int i;
145
146 for (i = 0; i < MAX_NO_OF_CHANNELS; i++) {
147 /* reset chip */
148 iowrite8(MOD_RM, base_addr +
149 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
150 status = ioread8(base_addr +
151 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
152 /* check reset bit */
153 if (!(status & MOD_RM))
154 break;
155 }
156
157 return i;
158 }
159
kvaser_pci_del_chan(struct net_device * dev)160 static void kvaser_pci_del_chan(struct net_device *dev)
161 {
162 struct sja1000_priv *priv;
163 struct kvaser_pci *board;
164 int i;
165
166 if (!dev)
167 return;
168 priv = netdev_priv(dev);
169 board = priv->priv;
170 if (!board)
171 return;
172
173 dev_info(&board->pci_dev->dev, "Removing device %s\n",
174 dev->name);
175
176 /* Disable PCI interrupts */
177 kvaser_pci_disable_irq(dev);
178
179 for (i = 0; i < board->no_channels - 1; i++) {
180 if (board->slave_dev[i]) {
181 dev_info(&board->pci_dev->dev, "Removing device %s\n",
182 board->slave_dev[i]->name);
183 unregister_sja1000dev(board->slave_dev[i]);
184 free_sja1000dev(board->slave_dev[i]);
185 }
186 }
187 unregister_sja1000dev(dev);
188
189 pci_iounmap(board->pci_dev, priv->reg_base);
190 pci_iounmap(board->pci_dev, board->conf_addr);
191 pci_iounmap(board->pci_dev, board->res_addr);
192
193 free_sja1000dev(dev);
194 }
195
kvaser_pci_add_chan(struct pci_dev * pdev,int channel,struct net_device ** master_dev,void __iomem * conf_addr,void __iomem * res_addr,void __iomem * base_addr)196 static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel,
197 struct net_device **master_dev,
198 void __iomem *conf_addr,
199 void __iomem *res_addr,
200 void __iomem *base_addr)
201 {
202 struct net_device *dev;
203 struct sja1000_priv *priv;
204 struct kvaser_pci *board;
205 int err;
206
207 dev = alloc_sja1000dev(sizeof(struct kvaser_pci));
208 if (dev == NULL)
209 return -ENOMEM;
210
211 priv = netdev_priv(dev);
212 board = priv->priv;
213
214 board->pci_dev = pdev;
215 board->channel = channel;
216
217 /* S5920 */
218 board->conf_addr = conf_addr;
219
220 /* XILINX board wide address */
221 board->res_addr = res_addr;
222
223 if (channel == 0) {
224 board->xilinx_ver =
225 ioread8(board->res_addr + XILINX_VERINT) >> 4;
226
227 /* Assert PTADR# - we're in passive mode so the other bits are
228 not important */
229 iowrite32(0x80808080UL, board->conf_addr + S5920_PTCR);
230
231 /* Enable interrupts from card */
232 kvaser_pci_enable_irq(dev);
233 } else {
234 struct sja1000_priv *master_priv = netdev_priv(*master_dev);
235 struct kvaser_pci *master_board = master_priv->priv;
236 master_board->slave_dev[channel - 1] = dev;
237 master_board->no_channels = channel + 1;
238 board->xilinx_ver = master_board->xilinx_ver;
239 }
240
241 priv->reg_base = base_addr + channel * KVASER_PCI_PORT_BYTES;
242
243 priv->read_reg = kvaser_pci_read_reg;
244 priv->write_reg = kvaser_pci_write_reg;
245
246 priv->can.clock.freq = KVASER_PCI_CAN_CLOCK;
247
248 priv->ocr = KVASER_PCI_OCR;
249 priv->cdr = KVASER_PCI_CDR;
250
251 priv->irq_flags = IRQF_SHARED;
252 dev->irq = pdev->irq;
253
254 dev_info(&pdev->dev, "reg_base=%p conf_addr=%p irq=%d\n",
255 priv->reg_base, board->conf_addr, dev->irq);
256
257 SET_NETDEV_DEV(dev, &pdev->dev);
258 dev->dev_id = channel;
259
260 /* Register SJA1000 device */
261 err = register_sja1000dev(dev);
262 if (err) {
263 dev_err(&pdev->dev, "Registering device failed (err=%d)\n",
264 err);
265 goto failure;
266 }
267
268 if (channel == 0)
269 *master_dev = dev;
270
271 return 0;
272
273 failure:
274 kvaser_pci_del_chan(dev);
275 return err;
276 }
277
kvaser_pci_init_one(struct pci_dev * pdev,const struct pci_device_id * ent)278 static int kvaser_pci_init_one(struct pci_dev *pdev,
279 const struct pci_device_id *ent)
280 {
281 int err;
282 struct net_device *master_dev = NULL;
283 struct sja1000_priv *priv;
284 struct kvaser_pci *board;
285 int no_channels;
286 void __iomem *base_addr = NULL;
287 void __iomem *conf_addr = NULL;
288 void __iomem *res_addr = NULL;
289 int i;
290
291 dev_info(&pdev->dev, "initializing device %04x:%04x\n",
292 pdev->vendor, pdev->device);
293
294 err = pci_enable_device(pdev);
295 if (err)
296 goto failure;
297
298 err = pci_request_regions(pdev, DRV_NAME);
299 if (err)
300 goto failure_release_pci;
301
302 /* S5920 */
303 conf_addr = pci_iomap(pdev, 0, PCI_CONFIG_PORT_SIZE);
304 if (conf_addr == NULL) {
305 err = -ENODEV;
306 goto failure_release_regions;
307 }
308
309 /* XILINX board wide address */
310 res_addr = pci_iomap(pdev, 2, PCI_PORT_XILINX_SIZE);
311 if (res_addr == NULL) {
312 err = -ENOMEM;
313 goto failure_iounmap;
314 }
315
316 base_addr = pci_iomap(pdev, 1, PCI_PORT_SIZE);
317 if (base_addr == NULL) {
318 err = -ENOMEM;
319 goto failure_iounmap;
320 }
321
322 no_channels = number_of_sja1000_chip(base_addr);
323 if (no_channels == 0) {
324 err = -ENOMEM;
325 goto failure_iounmap;
326 }
327
328 for (i = 0; i < no_channels; i++) {
329 err = kvaser_pci_add_chan(pdev, i, &master_dev,
330 conf_addr, res_addr,
331 base_addr);
332 if (err)
333 goto failure_cleanup;
334 }
335
336 priv = netdev_priv(master_dev);
337 board = priv->priv;
338
339 dev_info(&pdev->dev, "xilinx version=%d number of channels=%d\n",
340 board->xilinx_ver, board->no_channels);
341
342 pci_set_drvdata(pdev, master_dev);
343 return 0;
344
345 failure_cleanup:
346 kvaser_pci_del_chan(master_dev);
347
348 failure_iounmap:
349 if (conf_addr != NULL)
350 pci_iounmap(pdev, conf_addr);
351 if (res_addr != NULL)
352 pci_iounmap(pdev, res_addr);
353 if (base_addr != NULL)
354 pci_iounmap(pdev, base_addr);
355
356 failure_release_regions:
357 pci_release_regions(pdev);
358
359 failure_release_pci:
360 pci_disable_device(pdev);
361
362 failure:
363 return err;
364
365 }
366
kvaser_pci_remove_one(struct pci_dev * pdev)367 static void kvaser_pci_remove_one(struct pci_dev *pdev)
368 {
369 struct net_device *dev = pci_get_drvdata(pdev);
370
371 kvaser_pci_del_chan(dev);
372
373 pci_release_regions(pdev);
374 pci_disable_device(pdev);
375 }
376
377 static struct pci_driver kvaser_pci_driver = {
378 .name = DRV_NAME,
379 .id_table = kvaser_pci_tbl,
380 .probe = kvaser_pci_init_one,
381 .remove = kvaser_pci_remove_one,
382 };
383
384 module_pci_driver(kvaser_pci_driver);
385