1 #ifndef NETDEV_PCS_H
2 #define NETDEV_PCS_H
3
4 #include <linux/phy.h>
5 #include <linux/spinlock.h>
6 #include <linux/workqueue.h>
7
8 struct device_node;
9 struct ethtool_cmd;
10 struct fwnode_handle;
11 struct net_device;
12 struct phylink;
13
14 enum {
15 MLO_PAUSE_NONE,
16 MLO_PAUSE_RX = BIT(0),
17 MLO_PAUSE_TX = BIT(1),
18 MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
19 MLO_PAUSE_AN = BIT(2),
20
21 MLO_AN_PHY = 0, /* Conventional PHY */
22 MLO_AN_FIXED, /* Fixed-link mode */
23 MLO_AN_INBAND, /* In-band protocol */
24
25 /* PCS "negotiation" mode.
26 * PHYLINK_PCS_NEG_NONE - protocol has no inband capability
27 * PHYLINK_PCS_NEG_OUTBAND - some out of band or fixed link setting
28 * PHYLINK_PCS_NEG_INBAND_DISABLED - inband mode disabled, e.g.
29 * 1000base-X with autoneg off
30 * PHYLINK_PCS_NEG_INBAND_ENABLED - inband mode enabled
31 * Additionally, this can be tested using bitmasks:
32 * PHYLINK_PCS_NEG_INBAND - inband mode selected
33 * PHYLINK_PCS_NEG_ENABLED - negotiation mode enabled
34 */
35 PHYLINK_PCS_NEG_NONE = 0,
36 PHYLINK_PCS_NEG_ENABLED = BIT(4),
37 PHYLINK_PCS_NEG_OUTBAND = BIT(5),
38 PHYLINK_PCS_NEG_INBAND = BIT(6),
39 PHYLINK_PCS_NEG_INBAND_DISABLED = PHYLINK_PCS_NEG_INBAND,
40 PHYLINK_PCS_NEG_INBAND_ENABLED = PHYLINK_PCS_NEG_INBAND |
41 PHYLINK_PCS_NEG_ENABLED,
42
43 /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our
44 * autonegotiation advertisement. They correspond to the PAUSE and
45 * ASM_DIR bits defined by 802.3, respectively.
46 *
47 * The following table lists the values of tx_pause and rx_pause which
48 * might be requested in mac_link_up. The exact values depend on either
49 * the results of autonegotation (if MLO_PAUSE_AN is set) or user
50 * configuration (if MLO_PAUSE_AN is not set).
51 *
52 * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause
53 * ============= ============== ============ ==================
54 * 0 0 0 0/0
55 * 0 0 1 0/0
56 * 0 1 0 0/0, 0/1, 1/0, 1/1
57 * 0 1 1 0/0, 1/0
58 * 1 0 0 0/0, 1/1
59 * 1 0 1 0/0, 1/1
60 * 1 1 0 0/0, 0/1, 1/0, 1/1
61 * 1 1 1 0/0, 0/1, 1/1
62 *
63 * If you set MAC_ASYM_PAUSE, the user may request any combination of
64 * tx_pause and rx_pause. You do not have to support these
65 * combinations.
66 *
67 * However, you should support combinations of tx_pause and rx_pause
68 * which might be the result of autonegotation. For example, don't set
69 * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause
70 * at the same time.
71 */
72 MAC_SYM_PAUSE = BIT(0),
73 MAC_ASYM_PAUSE = BIT(1),
74 MAC_10HD = BIT(2),
75 MAC_10FD = BIT(3),
76 MAC_10 = MAC_10HD | MAC_10FD,
77 MAC_100HD = BIT(4),
78 MAC_100FD = BIT(5),
79 MAC_100 = MAC_100HD | MAC_100FD,
80 MAC_1000HD = BIT(6),
81 MAC_1000FD = BIT(7),
82 MAC_1000 = MAC_1000HD | MAC_1000FD,
83 MAC_2500FD = BIT(8),
84 MAC_5000FD = BIT(9),
85 MAC_10000FD = BIT(10),
86 MAC_20000FD = BIT(11),
87 MAC_25000FD = BIT(12),
88 MAC_40000FD = BIT(13),
89 MAC_50000FD = BIT(14),
90 MAC_56000FD = BIT(15),
91 MAC_100000FD = BIT(16),
92 MAC_200000FD = BIT(17),
93 MAC_400000FD = BIT(18),
94 };
95
phylink_autoneg_inband(unsigned int mode)96 static inline bool phylink_autoneg_inband(unsigned int mode)
97 {
98 return mode == MLO_AN_INBAND;
99 }
100
101 /**
102 * struct phylink_link_state - link state structure
103 * @advertising: ethtool bitmask containing advertised link modes
104 * @lp_advertising: ethtool bitmask containing link partner advertised link
105 * modes
106 * @interface: link &typedef phy_interface_t mode
107 * @speed: link speed, one of the SPEED_* constants.
108 * @duplex: link duplex mode, one of DUPLEX_* constants.
109 * @pause: link pause state, described by MLO_PAUSE_* constants.
110 * @rate_matching: rate matching being performed, one of the RATE_MATCH_*
111 * constants. If rate matching is taking place, then the speed/duplex of
112 * the medium link mode (@speed and @duplex) and the speed/duplex of the phy
113 * interface mode (@interface) are different.
114 * @link: true if the link is up.
115 * @an_complete: true if autonegotiation has completed.
116 */
117 struct phylink_link_state {
118 __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
119 __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
120 phy_interface_t interface;
121 int speed;
122 int duplex;
123 int pause;
124 int rate_matching;
125 unsigned int link:1;
126 unsigned int an_complete:1;
127 };
128
129 enum phylink_op_type {
130 PHYLINK_NETDEV = 0,
131 PHYLINK_DEV,
132 };
133
134 /**
135 * struct phylink_config - PHYLINK configuration structure
136 * @dev: a pointer to a struct device associated with the MAC
137 * @type: operation type of PHYLINK instance
138 * @poll_fixed_state: if true, starts link_poll,
139 * if MAC link is at %MLO_AN_FIXED mode.
140 * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM.
141 * @mac_requires_rxc: if true, the MAC always requires a receive clock from PHY.
142 * The PHY driver should start the clock signal as soon as
143 * possible and avoid stopping it during suspend events.
144 * @default_an_inband: if true, defaults to MLO_AN_INBAND rather than
145 * MLO_AN_PHY. A fixed-link specification will override.
146 * @get_fixed_state: callback to execute to determine the fixed link state,
147 * if MAC link is at %MLO_AN_FIXED mode.
148 * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx
149 * are supported by the MAC/PCS.
150 * @mac_capabilities: MAC pause/speed/duplex capabilities.
151 */
152 struct phylink_config {
153 struct device *dev;
154 enum phylink_op_type type;
155 bool poll_fixed_state;
156 bool mac_managed_pm;
157 bool mac_requires_rxc;
158 bool default_an_inband;
159 void (*get_fixed_state)(struct phylink_config *config,
160 struct phylink_link_state *state);
161 DECLARE_PHY_INTERFACE_MASK(supported_interfaces);
162 unsigned long mac_capabilities;
163 };
164
165 void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed);
166
167 /**
168 * struct phylink_mac_ops - MAC operations structure.
169 * @mac_get_caps: Get MAC capabilities for interface mode.
170 * @mac_select_pcs: Select a PCS for the interface mode.
171 * @mac_prepare: prepare for a major reconfiguration of the interface.
172 * @mac_config: configure the MAC for the selected mode and state.
173 * @mac_finish: finish a major reconfiguration of the interface.
174 * @mac_link_down: take the link down.
175 * @mac_link_up: allow the link to come up.
176 *
177 * The individual methods are described more fully below.
178 */
179 struct phylink_mac_ops {
180 unsigned long (*mac_get_caps)(struct phylink_config *config,
181 phy_interface_t interface);
182 struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config,
183 phy_interface_t interface);
184 int (*mac_prepare)(struct phylink_config *config, unsigned int mode,
185 phy_interface_t iface);
186 void (*mac_config)(struct phylink_config *config, unsigned int mode,
187 const struct phylink_link_state *state);
188 int (*mac_finish)(struct phylink_config *config, unsigned int mode,
189 phy_interface_t iface);
190 void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
191 phy_interface_t interface);
192 void (*mac_link_up)(struct phylink_config *config,
193 struct phy_device *phy, unsigned int mode,
194 phy_interface_t interface, int speed, int duplex,
195 bool tx_pause, bool rx_pause);
196 };
197
198 #if 0 /* For kernel-doc purposes only. */
199 /**
200 * mac_get_caps: Get MAC capabilities for interface mode.
201 * @config: a pointer to a &struct phylink_config.
202 * @interface: PHY interface mode.
203 *
204 * Optional method. When not provided, config->mac_capabilities will be used.
205 * When implemented, this returns the MAC capabilities for the specified
206 * interface mode where there is some special handling required by the MAC
207 * driver (e.g. not supporting half-duplex in certain interface modes.)
208 */
209 unsigned long mac_get_caps(struct phylink_config *config,
210 phy_interface_t interface);
211 /**
212 * mac_select_pcs: Select a PCS for the interface mode.
213 * @config: a pointer to a &struct phylink_config.
214 * @interface: PHY interface mode for PCS
215 *
216 * Return the &struct phylink_pcs for the specified interface mode, or
217 * NULL if none is required, or an error pointer on error.
218 *
219 * This must not modify any state. It is used to query which PCS should
220 * be used. Phylink will use this during validation to ensure that the
221 * configuration is valid, and when setting a configuration to internally
222 * set the PCS that will be used.
223 */
224 struct phylink_pcs *mac_select_pcs(struct phylink_config *config,
225 phy_interface_t interface);
226
227 /**
228 * mac_prepare() - prepare to change the PHY interface mode
229 * @config: a pointer to a &struct phylink_config.
230 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
231 * @iface: interface mode to switch to
232 *
233 * phylink will call this method at the beginning of a full initialisation
234 * of the link, which includes changing the interface mode or at initial
235 * startup time. It may be called for the current mode. The MAC driver
236 * should perform whatever actions are required, e.g. disabling the
237 * Serdes PHY.
238 *
239 * This will be the first call in the sequence:
240 * - mac_prepare()
241 * - mac_config()
242 * - pcs_config()
243 * - possible pcs_an_restart()
244 * - mac_finish()
245 *
246 * Returns zero on success, or negative errno on failure which will be
247 * reported to the kernel log.
248 */
249 int mac_prepare(struct phylink_config *config, unsigned int mode,
250 phy_interface_t iface);
251
252 /**
253 * mac_config() - configure the MAC for the selected mode and state
254 * @config: a pointer to a &struct phylink_config.
255 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
256 * @state: a pointer to a &struct phylink_link_state.
257 *
258 * Note - not all members of @state are valid. In particular,
259 * @state->lp_advertising, @state->link, @state->an_complete are never
260 * guaranteed to be correct, and so any mac_config() implementation must
261 * never reference these fields.
262 *
263 * This will only be called to reconfigure the MAC for a "major" change in
264 * e.g. interface mode. It will not be called for changes in speed, duplex
265 * or pause modes or to change the in-band advertisement.
266 *
267 * In all negotiation modes, as defined by @mode, @state->pause indicates the
268 * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
269 * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
270 * pause frames and/or act on received pause frames respectively. Otherwise,
271 * the results of in-band negotiation/status from the MAC PCS should be used
272 * to control the MAC pause mode settings.
273 *
274 * The action performed depends on the currently selected mode:
275 *
276 * %MLO_AN_FIXED, %MLO_AN_PHY:
277 * Configure for non-inband negotiation mode, where the link settings
278 * are completely communicated via mac_link_up(). The physical link
279 * protocol from the MAC is specified by @state->interface.
280 *
281 * @state->advertising may be used, but is not required.
282 *
283 * Older drivers (prior to the mac_link_up() change) may use @state->speed,
284 * @state->duplex and @state->pause to configure the MAC, but this is
285 * deprecated; such drivers should be converted to use mac_link_up().
286 *
287 * Other members of @state must be ignored.
288 *
289 * Valid state members: interface, advertising.
290 * Deprecated state members: speed, duplex, pause.
291 *
292 * %MLO_AN_INBAND:
293 * place the link in an inband negotiation mode (such as 802.3z
294 * 1000base-X or Cisco SGMII mode depending on the @state->interface
295 * mode). In both cases, link state management (whether the link
296 * is up or not) is performed by the MAC, and reported via the
297 * pcs_get_state() callback. Changes in link state must be made
298 * by calling phylink_mac_change().
299 *
300 * Interface mode specific details are mentioned below.
301 *
302 * If in 802.3z mode, the link speed is fixed, dependent on the
303 * @state->interface. Duplex and pause modes are negotiated via
304 * the in-band configuration word. Advertised pause modes are set
305 * according to the @state->an_enabled and @state->advertising
306 * flags. Beware of MACs which only support full duplex at gigabit
307 * and higher speeds.
308 *
309 * If in Cisco SGMII mode, the link speed and duplex mode are passed
310 * in the serial bitstream 16-bit configuration word, and the MAC
311 * should be configured to read these bits and acknowledge the
312 * configuration word. Nothing is advertised by the MAC. The MAC is
313 * responsible for reading the configuration word and configuring
314 * itself accordingly.
315 *
316 * Valid state members: interface, an_enabled, pause, advertising.
317 *
318 * Implementations are expected to update the MAC to reflect the
319 * requested settings - i.o.w., if nothing has changed between two
320 * calls, no action is expected. If only flow control settings have
321 * changed, flow control should be updated *without* taking the link
322 * down. This "update" behaviour is critical to avoid bouncing the
323 * link up status.
324 */
325 void mac_config(struct phylink_config *config, unsigned int mode,
326 const struct phylink_link_state *state);
327
328 /**
329 * mac_finish() - finish a to change the PHY interface mode
330 * @config: a pointer to a &struct phylink_config.
331 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
332 * @iface: interface mode to switch to
333 *
334 * phylink will call this if it called mac_prepare() to allow the MAC to
335 * complete any necessary steps after the MAC and PCS have been configured
336 * for the @mode and @iface. E.g. a MAC driver may wish to re-enable the
337 * Serdes PHY here if it was previously disabled by mac_prepare().
338 *
339 * Returns zero on success, or negative errno on failure which will be
340 * reported to the kernel log.
341 */
342 int mac_finish(struct phylink_config *config, unsigned int mode,
343 phy_interface_t iface);
344
345 /**
346 * mac_link_down() - take the link down
347 * @config: a pointer to a &struct phylink_config.
348 * @mode: link autonegotiation mode
349 * @interface: link &typedef phy_interface_t mode
350 *
351 * If @mode is not an in-band negotiation mode (as defined by
352 * phylink_autoneg_inband()), force the link down and disable any
353 * Energy Efficient Ethernet MAC configuration. Interface type
354 * selection must be done in mac_config().
355 */
356 void mac_link_down(struct phylink_config *config, unsigned int mode,
357 phy_interface_t interface);
358
359 /**
360 * mac_link_up() - allow the link to come up
361 * @config: a pointer to a &struct phylink_config.
362 * @phy: any attached phy
363 * @mode: link autonegotiation mode
364 * @interface: link &typedef phy_interface_t mode
365 * @speed: link speed
366 * @duplex: link duplex
367 * @tx_pause: link transmit pause enablement status
368 * @rx_pause: link receive pause enablement status
369 *
370 * Configure the MAC for an established link.
371 *
372 * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
373 * settings, and should be used to configure the MAC block appropriately
374 * where these settings are not automatically conveyed from the PCS block,
375 * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
376 * is disabled.
377 *
378 * Note that when 802.3z in-band negotiation is in use, it is possible
379 * that the user wishes to override the pause settings, and this should
380 * be allowed when considering the implementation of this method.
381 *
382 * If in-band negotiation mode is disabled, allow the link to come up. If
383 * @phy is non-%NULL, configure Energy Efficient Ethernet by calling
384 * phy_init_eee() and perform appropriate MAC configuration for EEE.
385 * Interface type selection must be done in mac_config().
386 */
387 void mac_link_up(struct phylink_config *config, struct phy_device *phy,
388 unsigned int mode, phy_interface_t interface,
389 int speed, int duplex, bool tx_pause, bool rx_pause);
390 #endif
391
392 struct phylink_pcs_ops;
393
394 /**
395 * struct phylink_pcs - PHYLINK PCS instance
396 * @ops: a pointer to the &struct phylink_pcs_ops structure
397 * @phylink: pointer to &struct phylink_config
398 * @neg_mode: provide PCS neg mode via "mode" argument
399 * @poll: poll the PCS for link changes
400 * @rxc_always_on: The MAC driver requires the reference clock
401 * to always be on. Standalone PCS drivers which
402 * do not have access to a PHY device can check
403 * this instead of PHY_F_RXC_ALWAYS_ON.
404 *
405 * This structure is designed to be embedded within the PCS private data,
406 * and will be passed between phylink and the PCS.
407 *
408 * The @phylink member is private to phylink and must not be touched by
409 * the PCS driver.
410 */
411 struct phylink_pcs {
412 const struct phylink_pcs_ops *ops;
413 struct phylink *phylink;
414 bool neg_mode;
415 bool poll;
416 bool rxc_always_on;
417 };
418
419 /**
420 * struct phylink_pcs_ops - MAC PCS operations structure.
421 * @pcs_validate: validate the link configuration.
422 * @pcs_enable: enable the PCS.
423 * @pcs_disable: disable the PCS.
424 * @pcs_pre_config: pre-mac_config method (for errata)
425 * @pcs_post_config: post-mac_config method (for arrata)
426 * @pcs_get_state: read the current MAC PCS link state from the hardware.
427 * @pcs_config: configure the MAC PCS for the selected mode and state.
428 * @pcs_an_restart: restart 802.3z BaseX autonegotiation.
429 * @pcs_link_up: program the PCS for the resolved link configuration
430 * (where necessary).
431 * @pcs_pre_init: configure PCS components necessary for MAC hardware
432 * initialization e.g. RX clock for stmmac.
433 */
434 struct phylink_pcs_ops {
435 int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported,
436 const struct phylink_link_state *state);
437 int (*pcs_enable)(struct phylink_pcs *pcs);
438 void (*pcs_disable)(struct phylink_pcs *pcs);
439 void (*pcs_pre_config)(struct phylink_pcs *pcs,
440 phy_interface_t interface);
441 int (*pcs_post_config)(struct phylink_pcs *pcs,
442 phy_interface_t interface);
443 void (*pcs_get_state)(struct phylink_pcs *pcs,
444 struct phylink_link_state *state);
445 int (*pcs_config)(struct phylink_pcs *pcs, unsigned int neg_mode,
446 phy_interface_t interface,
447 const unsigned long *advertising,
448 bool permit_pause_to_mac);
449 void (*pcs_an_restart)(struct phylink_pcs *pcs);
450 void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int neg_mode,
451 phy_interface_t interface, int speed, int duplex);
452 int (*pcs_pre_init)(struct phylink_pcs *pcs);
453 };
454
455 #if 0 /* For kernel-doc purposes only. */
456 /**
457 * pcs_validate() - validate the link configuration.
458 * @pcs: a pointer to a &struct phylink_pcs.
459 * @supported: ethtool bitmask for supported link modes.
460 * @state: a const pointer to a &struct phylink_link_state.
461 *
462 * Validate the interface mode, and advertising's autoneg bit, removing any
463 * media ethtool link modes that would not be supportable from the supported
464 * mask. Phylink will propagate the changes to the advertising mask. See the
465 * &struct phylink_mac_ops validate() method.
466 *
467 * Returns -EINVAL if the interface mode/autoneg mode is not supported.
468 * Returns non-zero positive if the link state can be supported.
469 */
470 int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
471 const struct phylink_link_state *state);
472
473 /**
474 * pcs_enable() - enable the PCS.
475 * @pcs: a pointer to a &struct phylink_pcs.
476 */
477 int pcs_enable(struct phylink_pcs *pcs);
478
479 /**
480 * pcs_disable() - disable the PCS.
481 * @pcs: a pointer to a &struct phylink_pcs.
482 */
483 void pcs_disable(struct phylink_pcs *pcs);
484
485 /**
486 * pcs_get_state() - Read the current inband link state from the hardware
487 * @pcs: a pointer to a &struct phylink_pcs.
488 * @state: a pointer to a &struct phylink_link_state.
489 *
490 * Read the current inband link state from the MAC PCS, reporting the
491 * current speed in @state->speed, duplex mode in @state->duplex, pause
492 * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
493 * negotiation completion state in @state->an_complete, and link up state
494 * in @state->link. If possible, @state->lp_advertising should also be
495 * populated.
496 */
497 void pcs_get_state(struct phylink_pcs *pcs,
498 struct phylink_link_state *state);
499
500 /**
501 * pcs_config() - Configure the PCS mode and advertisement
502 * @pcs: a pointer to a &struct phylink_pcs.
503 * @neg_mode: link negotiation mode (see below)
504 * @interface: interface mode to be used
505 * @advertising: adertisement ethtool link mode mask
506 * @permit_pause_to_mac: permit forwarding pause resolution to MAC
507 *
508 * Configure the PCS for the operating mode, the interface mode, and set
509 * the advertisement mask. @permit_pause_to_mac indicates whether the
510 * hardware may forward the pause mode resolution to the MAC.
511 *
512 * When operating in %MLO_AN_INBAND, inband should always be enabled,
513 * otherwise inband should be disabled.
514 *
515 * For SGMII, there is no advertisement from the MAC side, the PCS should
516 * be programmed to acknowledge the inband word from the PHY.
517 *
518 * For 1000BASE-X, the advertisement should be programmed into the PCS.
519 *
520 * For most 10GBASE-R, there is no advertisement.
521 *
522 * The %neg_mode argument should be tested via the phylink_mode_*() family of
523 * functions, or for PCS that set pcs->neg_mode true, should be tested
524 * against the PHYLINK_PCS_NEG_* definitions.
525 */
526 int pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
527 phy_interface_t interface, const unsigned long *advertising,
528 bool permit_pause_to_mac);
529
530 /**
531 * pcs_an_restart() - restart 802.3z BaseX autonegotiation
532 * @pcs: a pointer to a &struct phylink_pcs.
533 *
534 * When PCS ops are present, this overrides mac_an_restart() in &struct
535 * phylink_mac_ops.
536 */
537 void pcs_an_restart(struct phylink_pcs *pcs);
538
539 /**
540 * pcs_link_up() - program the PCS for the resolved link configuration
541 * @pcs: a pointer to a &struct phylink_pcs.
542 * @neg_mode: link negotiation mode (see below)
543 * @interface: link &typedef phy_interface_t mode
544 * @speed: link speed
545 * @duplex: link duplex
546 *
547 * This call will be made just before mac_link_up() to inform the PCS of
548 * the resolved link parameters. For example, a PCS operating in SGMII
549 * mode without in-band AN needs to be manually configured for the link
550 * and duplex setting. Otherwise, this should be a no-op.
551 *
552 * The %mode argument should be tested via the phylink_mode_*() family of
553 * functions, or for PCS that set pcs->neg_mode true, should be tested
554 * against the PHYLINK_PCS_NEG_* definitions.
555 */
556 void pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode,
557 phy_interface_t interface, int speed, int duplex);
558
559 /**
560 * pcs_pre_init() - Configure PCS components necessary for MAC initialization
561 * @pcs: a pointer to a &struct phylink_pcs.
562 *
563 * This function can be called by MAC drivers through the
564 * phylink_pcs_pre_init() wrapper, before their hardware is initialized. It
565 * should not be called after the link is brought up, as reconfiguring the PCS
566 * at this point could break the link.
567 *
568 * Some MAC devices require specific hardware initialization to be performed by
569 * their associated PCS device before they can properly initialize their own
570 * hardware. An example of this is the initialization of stmmac controllers,
571 * which requires an active REF_CLK signal to be provided by the PHY/PCS.
572 *
573 * By calling phylink_pcs_pre_init(), MAC drivers can ensure that the PCS is
574 * setup in a way that allows for successful hardware initialization.
575 *
576 * The specific configuration performed by pcs_pre_init() is dependent on the
577 * model of PCS and the requirements of the MAC device attached to it. PCS
578 * driver authors should consider whether their target device is to be used in
579 * conjunction with a MAC device whose driver calls phylink_pcs_pre_init(). MAC
580 * driver authors should document their requirements for the PCS
581 * pre-initialization.
582 *
583 */
584 int pcs_pre_init(struct phylink_pcs *pcs);
585
586 #endif
587
588 struct phylink *phylink_create(struct phylink_config *,
589 const struct fwnode_handle *,
590 phy_interface_t,
591 const struct phylink_mac_ops *);
592 void phylink_destroy(struct phylink *);
593 bool phylink_expects_phy(struct phylink *pl);
594
595 int phylink_connect_phy(struct phylink *, struct phy_device *);
596 int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags);
597 int phylink_fwnode_phy_connect(struct phylink *pl,
598 const struct fwnode_handle *fwnode,
599 u32 flags);
600 void phylink_disconnect_phy(struct phylink *);
601 int phylink_set_fixed_link(struct phylink *,
602 const struct phylink_link_state *);
603
604 void phylink_mac_change(struct phylink *, bool up);
605 void phylink_pcs_change(struct phylink_pcs *, bool up);
606
607 int phylink_pcs_pre_init(struct phylink *pl, struct phylink_pcs *pcs);
608
609 void phylink_start(struct phylink *);
610 void phylink_stop(struct phylink *);
611
612 void phylink_suspend(struct phylink *pl, bool mac_wol);
613 void phylink_resume(struct phylink *pl);
614
615 void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *);
616 int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *);
617
618 int phylink_ethtool_ksettings_get(struct phylink *,
619 struct ethtool_link_ksettings *);
620 int phylink_ethtool_ksettings_set(struct phylink *,
621 const struct ethtool_link_ksettings *);
622 int phylink_ethtool_nway_reset(struct phylink *);
623 void phylink_ethtool_get_pauseparam(struct phylink *,
624 struct ethtool_pauseparam *);
625 int phylink_ethtool_set_pauseparam(struct phylink *,
626 struct ethtool_pauseparam *);
627 int phylink_get_eee_err(struct phylink *);
628 int phylink_init_eee(struct phylink *, bool);
629 int phylink_ethtool_get_eee(struct phylink *link, struct ethtool_keee *eee);
630 int phylink_ethtool_set_eee(struct phylink *link, struct ethtool_keee *eee);
631 int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
632 int phylink_speed_down(struct phylink *pl, bool sync);
633 int phylink_speed_up(struct phylink *pl);
634
635 #define phylink_zero(bm) \
636 bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS)
637 #define __phylink_do_bit(op, bm, mode) \
638 op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm)
639
640 #define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode)
641 #define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode)
642 #define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode)
643
644 void phylink_set_port_modes(unsigned long *bits);
645
646 /**
647 * phylink_get_link_timer_ns - return the PCS link timer value
648 * @interface: link &typedef phy_interface_t mode
649 *
650 * Return the PCS link timer setting in nanoseconds for the PHY @interface
651 * mode, or -EINVAL if not appropriate.
652 */
phylink_get_link_timer_ns(phy_interface_t interface)653 static inline int phylink_get_link_timer_ns(phy_interface_t interface)
654 {
655 switch (interface) {
656 case PHY_INTERFACE_MODE_SGMII:
657 case PHY_INTERFACE_MODE_QSGMII:
658 case PHY_INTERFACE_MODE_USXGMII:
659 case PHY_INTERFACE_MODE_10G_QXGMII:
660 return 1600000;
661
662 case PHY_INTERFACE_MODE_1000BASEX:
663 case PHY_INTERFACE_MODE_2500BASEX:
664 return 10000000;
665
666 default:
667 return -EINVAL;
668 }
669 }
670
671 void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state,
672 u16 bmsr, u16 lpa);
673 void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
674 struct phylink_link_state *state);
675 int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface,
676 const unsigned long *advertising);
677 int phylink_mii_c22_pcs_config(struct mdio_device *pcs,
678 phy_interface_t interface,
679 const unsigned long *advertising,
680 unsigned int neg_mode);
681 void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
682
683 void phylink_resolve_c73(struct phylink_link_state *state);
684
685 void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
686 struct phylink_link_state *state);
687
688 void phylink_decode_usxgmii_word(struct phylink_link_state *state,
689 uint16_t lpa);
690 #endif
691