1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> 4 <http://rt2x00.serialmonkey.com> 5 6 */ 7 8 /* 9 Module: rt2x00dump 10 Abstract: 11 Data structures for the rt2x00debug & userspace. 12 13 The declarations in this file can be used by both rt2x00 14 and userspace and therefore should be kept together in 15 this file. 16 */ 17 18 #ifndef RT2X00DUMP_H 19 #define RT2X00DUMP_H 20 21 /** 22 * DOC: Introduction 23 * 24 * This header is intended to be exported to userspace, 25 * to make the structures and enumerations available to userspace 26 * applications. This means that all data types should be exportable. 27 * 28 * When rt2x00 is compiled with debugfs support enabled, 29 * it is possible to capture all data coming in and out of the device 30 * by reading the frame dump file. This file can have only a single reader. 31 * The following frames will be reported: 32 * - All incoming frames (rx) 33 * - All outgoing frames (tx, including beacon and atim) 34 * - All completed frames (txdone including atim) 35 * 36 * The data is send to the file using the following format: 37 * 38 * [rt2x00dump header][hardware descriptor][ieee802.11 frame] 39 * 40 * rt2x00dump header: The description of the dumped frame, as well as 41 * additional information useful for debugging. See &rt2x00dump_hdr. 42 * hardware descriptor: Descriptor that was used to receive or transmit 43 * the frame. 44 * ieee802.11 frame: The actual frame that was received or transmitted. 45 */ 46 47 /** 48 * enum rt2x00_dump_type - Frame type 49 * 50 * These values are used for the @type member of &rt2x00dump_hdr. 51 * @DUMP_FRAME_RXDONE: This frame has been received by the hardware. 52 * @DUMP_FRAME_TX: This frame is queued for transmission to the hardware. 53 * @DUMP_FRAME_TXDONE: This frame indicates the device has handled 54 * the tx event which has either succeeded or failed. A frame 55 * with this type should also have been reported with as a 56 * %DUMP_FRAME_TX frame. 57 * @DUMP_FRAME_BEACON: This beacon frame is queued for transmission to the 58 * hardware. 59 */ 60 enum rt2x00_dump_type { 61 DUMP_FRAME_RXDONE = 1, 62 DUMP_FRAME_TX = 2, 63 DUMP_FRAME_TXDONE = 3, 64 DUMP_FRAME_BEACON = 4, 65 }; 66 67 /** 68 * struct rt2x00dump_hdr - Dump frame header 69 * 70 * Each frame dumped to the debugfs file starts with this header 71 * attached. This header contains the description of the actual 72 * frame which was dumped. 73 * 74 * New fields inside the structure must be appended to the end of 75 * the structure. This way userspace tools compiled for earlier 76 * header versions can still correctly handle the frame dump 77 * (although they will not handle all data passed to them in the dump). 78 * 79 * @version: Header version should always be set to %DUMP_HEADER_VERSION. 80 * This field must be checked by userspace to determine if it can 81 * handle this frame. 82 * @header_length: The length of the &rt2x00dump_hdr structure. This is 83 * used for compatibility reasons so userspace can easily determine 84 * the location of the next field in the dump. 85 * @desc_length: The length of the device descriptor. 86 * @data_length: The length of the frame data (including the ieee802.11 header. 87 * @chip_rt: RT chipset 88 * @chip_rf: RF chipset 89 * @chip_rev: Chipset revision 90 * @type: The frame type (&rt2x00_dump_type) 91 * @queue_index: The index number of the data queue. 92 * @entry_index: The index number of the entry inside the data queue. 93 * @timestamp_sec: Timestamp - seconds 94 * @timestamp_usec: Timestamp - microseconds 95 */ 96 struct rt2x00dump_hdr { 97 __le32 version; 98 #define DUMP_HEADER_VERSION 3 99 100 __le32 header_length; 101 __le32 desc_length; 102 __le32 data_length; 103 104 __le16 chip_rt; 105 __le16 chip_rf; 106 __le16 chip_rev; 107 108 __le16 type; 109 __u8 queue_index; 110 __u8 entry_index; 111 112 __le32 timestamp_sec; 113 __le32 timestamp_usec; 114 }; 115 116 #endif /* RT2X00DUMP_H */ 117