1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Derived from many drivers using generic_serial interface.
4 *
5 * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
6 *
7 * Serial driver for BCM63xx integrated UART.
8 *
9 * Hardware flow control was _not_ tested since I only have RX/TX on
10 * my board.
11 */
12
13 #include <linux/kernel.h>
14 #include <linux/platform_device.h>
15 #include <linux/init.h>
16 #include <linux/delay.h>
17 #include <linux/module.h>
18 #include <linux/console.h>
19 #include <linux/clk.h>
20 #include <linux/tty.h>
21 #include <linux/tty_flip.h>
22 #include <linux/sysrq.h>
23 #include <linux/serial.h>
24 #include <linux/serial_core.h>
25 #include <linux/serial_bcm63xx.h>
26 #include <linux/io.h>
27 #include <linux/of.h>
28
29 #define BCM63XX_NR_UARTS 2
30
31 static struct uart_port ports[BCM63XX_NR_UARTS];
32
33 /*
34 * rx interrupt mask / stat
35 *
36 * mask:
37 * - rx fifo full
38 * - rx fifo above threshold
39 * - rx fifo not empty for too long
40 */
41 #define UART_RX_INT_MASK (UART_IR_MASK(UART_IR_RXOVER) | \
42 UART_IR_MASK(UART_IR_RXTHRESH) | \
43 UART_IR_MASK(UART_IR_RXTIMEOUT))
44
45 #define UART_RX_INT_STAT (UART_IR_STAT(UART_IR_RXOVER) | \
46 UART_IR_STAT(UART_IR_RXTHRESH) | \
47 UART_IR_STAT(UART_IR_RXTIMEOUT))
48
49 /*
50 * tx interrupt mask / stat
51 *
52 * mask:
53 * - tx fifo empty
54 * - tx fifo below threshold
55 */
56 #define UART_TX_INT_MASK (UART_IR_MASK(UART_IR_TXEMPTY) | \
57 UART_IR_MASK(UART_IR_TXTRESH))
58
59 #define UART_TX_INT_STAT (UART_IR_STAT(UART_IR_TXEMPTY) | \
60 UART_IR_STAT(UART_IR_TXTRESH))
61
62 /*
63 * external input interrupt
64 *
65 * mask: any edge on CTS, DCD
66 */
67 #define UART_EXTINP_INT_MASK (UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \
68 UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD))
69
70 /*
71 * handy uart register accessor
72 */
bcm_uart_readl(struct uart_port * port,unsigned int offset)73 static inline unsigned int bcm_uart_readl(struct uart_port *port,
74 unsigned int offset)
75 {
76 return __raw_readl(port->membase + offset);
77 }
78
bcm_uart_writel(struct uart_port * port,unsigned int value,unsigned int offset)79 static inline void bcm_uart_writel(struct uart_port *port,
80 unsigned int value, unsigned int offset)
81 {
82 __raw_writel(value, port->membase + offset);
83 }
84
85 /*
86 * serial core request to check if uart tx fifo is empty
87 */
bcm_uart_tx_empty(struct uart_port * port)88 static unsigned int bcm_uart_tx_empty(struct uart_port *port)
89 {
90 unsigned int val;
91
92 val = bcm_uart_readl(port, UART_IR_REG);
93 return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0;
94 }
95
96 /*
97 * serial core request to set RTS and DTR pin state and loopback mode
98 */
bcm_uart_set_mctrl(struct uart_port * port,unsigned int mctrl)99 static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
100 {
101 unsigned int val;
102
103 val = bcm_uart_readl(port, UART_MCTL_REG);
104 val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK);
105 /* invert of written value is reflected on the pin */
106 if (!(mctrl & TIOCM_DTR))
107 val |= UART_MCTL_DTR_MASK;
108 if (!(mctrl & TIOCM_RTS))
109 val |= UART_MCTL_RTS_MASK;
110 bcm_uart_writel(port, val, UART_MCTL_REG);
111
112 val = bcm_uart_readl(port, UART_CTL_REG);
113 if (mctrl & TIOCM_LOOP)
114 val |= UART_CTL_LOOPBACK_MASK;
115 else
116 val &= ~UART_CTL_LOOPBACK_MASK;
117 bcm_uart_writel(port, val, UART_CTL_REG);
118 }
119
120 /*
121 * serial core request to return RI, CTS, DCD and DSR pin state
122 */
bcm_uart_get_mctrl(struct uart_port * port)123 static unsigned int bcm_uart_get_mctrl(struct uart_port *port)
124 {
125 unsigned int val, mctrl;
126
127 mctrl = 0;
128 val = bcm_uart_readl(port, UART_EXTINP_REG);
129 if (val & UART_EXTINP_RI_MASK)
130 mctrl |= TIOCM_RI;
131 if (val & UART_EXTINP_CTS_MASK)
132 mctrl |= TIOCM_CTS;
133 if (val & UART_EXTINP_DCD_MASK)
134 mctrl |= TIOCM_CD;
135 if (val & UART_EXTINP_DSR_MASK)
136 mctrl |= TIOCM_DSR;
137 return mctrl;
138 }
139
140 /*
141 * serial core request to disable tx ASAP (used for flow control)
142 */
bcm_uart_stop_tx(struct uart_port * port)143 static void bcm_uart_stop_tx(struct uart_port *port)
144 {
145 unsigned int val;
146
147 val = bcm_uart_readl(port, UART_CTL_REG);
148 val &= ~(UART_CTL_TXEN_MASK);
149 bcm_uart_writel(port, val, UART_CTL_REG);
150
151 val = bcm_uart_readl(port, UART_IR_REG);
152 val &= ~UART_TX_INT_MASK;
153 bcm_uart_writel(port, val, UART_IR_REG);
154 }
155
156 /*
157 * serial core request to (re)enable tx
158 */
bcm_uart_start_tx(struct uart_port * port)159 static void bcm_uart_start_tx(struct uart_port *port)
160 {
161 unsigned int val;
162
163 val = bcm_uart_readl(port, UART_IR_REG);
164 val |= UART_TX_INT_MASK;
165 bcm_uart_writel(port, val, UART_IR_REG);
166
167 val = bcm_uart_readl(port, UART_CTL_REG);
168 val |= UART_CTL_TXEN_MASK;
169 bcm_uart_writel(port, val, UART_CTL_REG);
170 }
171
172 /*
173 * serial core request to stop rx, called before port shutdown
174 */
bcm_uart_stop_rx(struct uart_port * port)175 static void bcm_uart_stop_rx(struct uart_port *port)
176 {
177 unsigned int val;
178
179 val = bcm_uart_readl(port, UART_IR_REG);
180 val &= ~UART_RX_INT_MASK;
181 bcm_uart_writel(port, val, UART_IR_REG);
182 }
183
184 /*
185 * serial core request to enable modem status interrupt reporting
186 */
bcm_uart_enable_ms(struct uart_port * port)187 static void bcm_uart_enable_ms(struct uart_port *port)
188 {
189 unsigned int val;
190
191 val = bcm_uart_readl(port, UART_IR_REG);
192 val |= UART_IR_MASK(UART_IR_EXTIP);
193 bcm_uart_writel(port, val, UART_IR_REG);
194 }
195
196 /*
197 * serial core request to start/stop emitting break char
198 */
bcm_uart_break_ctl(struct uart_port * port,int ctl)199 static void bcm_uart_break_ctl(struct uart_port *port, int ctl)
200 {
201 unsigned long flags;
202 unsigned int val;
203
204 uart_port_lock_irqsave(port, &flags);
205
206 val = bcm_uart_readl(port, UART_CTL_REG);
207 if (ctl)
208 val |= UART_CTL_XMITBRK_MASK;
209 else
210 val &= ~UART_CTL_XMITBRK_MASK;
211 bcm_uart_writel(port, val, UART_CTL_REG);
212
213 uart_port_unlock_irqrestore(port, flags);
214 }
215
216 /*
217 * return port type in string format
218 */
bcm_uart_type(struct uart_port * port)219 static const char *bcm_uart_type(struct uart_port *port)
220 {
221 return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL;
222 }
223
224 /*
225 * read all chars in rx fifo and send them to core
226 */
bcm_uart_do_rx(struct uart_port * port)227 static void bcm_uart_do_rx(struct uart_port *port)
228 {
229 struct tty_port *tty_port = &port->state->port;
230 unsigned int max_count;
231
232 /* limit number of char read in interrupt, should not be
233 * higher than fifo size anyway since we're much faster than
234 * serial port */
235 max_count = 32;
236 do {
237 unsigned int iestat, c, cstat;
238 char flag;
239
240 /* get overrun/fifo empty information from ier
241 * register */
242 iestat = bcm_uart_readl(port, UART_IR_REG);
243
244 if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
245 unsigned int val;
246
247 /* fifo reset is required to clear
248 * interrupt */
249 val = bcm_uart_readl(port, UART_CTL_REG);
250 val |= UART_CTL_RSTRXFIFO_MASK;
251 bcm_uart_writel(port, val, UART_CTL_REG);
252
253 port->icount.overrun++;
254 tty_insert_flip_char(tty_port, 0, TTY_OVERRUN);
255 }
256
257 if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
258 break;
259
260 cstat = c = bcm_uart_readl(port, UART_FIFO_REG);
261 port->icount.rx++;
262 flag = TTY_NORMAL;
263 c &= 0xff;
264
265 if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) {
266 /* do stats first */
267 if (cstat & UART_FIFO_BRKDET_MASK) {
268 port->icount.brk++;
269 if (uart_handle_break(port))
270 continue;
271 }
272
273 if (cstat & UART_FIFO_PARERR_MASK)
274 port->icount.parity++;
275 if (cstat & UART_FIFO_FRAMEERR_MASK)
276 port->icount.frame++;
277
278 /* update flag wrt read_status_mask */
279 cstat &= port->read_status_mask;
280 if (cstat & UART_FIFO_BRKDET_MASK)
281 flag = TTY_BREAK;
282 if (cstat & UART_FIFO_FRAMEERR_MASK)
283 flag = TTY_FRAME;
284 if (cstat & UART_FIFO_PARERR_MASK)
285 flag = TTY_PARITY;
286 }
287
288 if (uart_prepare_sysrq_char(port, c))
289 continue;
290
291 if ((cstat & port->ignore_status_mask) == 0)
292 tty_insert_flip_char(tty_port, c, flag);
293
294 } while (--max_count);
295
296 tty_flip_buffer_push(tty_port);
297 }
298
299 /*
300 * fill tx fifo with chars to send, stop when fifo is about to be full
301 * or when all chars have been sent.
302 */
bcm_uart_do_tx(struct uart_port * port)303 static void bcm_uart_do_tx(struct uart_port *port)
304 {
305 unsigned int val;
306 bool pending;
307 u8 ch;
308
309 val = bcm_uart_readl(port, UART_MCTL_REG);
310 val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
311 pending = uart_port_tx_limited_flags(port, ch, UART_TX_NOSTOP,
312 port->fifosize - val,
313 true,
314 bcm_uart_writel(port, ch, UART_FIFO_REG),
315 ({}));
316 if (pending)
317 return;
318
319 /* nothing to send, disable transmit interrupt */
320 val = bcm_uart_readl(port, UART_IR_REG);
321 val &= ~UART_TX_INT_MASK;
322 bcm_uart_writel(port, val, UART_IR_REG);
323
324 if (uart_tx_stopped(port))
325 bcm_uart_stop_tx(port);
326 }
327
328 /*
329 * process uart interrupt
330 */
bcm_uart_interrupt(int irq,void * dev_id)331 static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id)
332 {
333 struct uart_port *port;
334 unsigned int irqstat;
335
336 port = dev_id;
337 uart_port_lock(port);
338
339 irqstat = bcm_uart_readl(port, UART_IR_REG);
340 if (irqstat & UART_RX_INT_STAT)
341 bcm_uart_do_rx(port);
342
343 if (irqstat & UART_TX_INT_STAT)
344 bcm_uart_do_tx(port);
345
346 if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) {
347 unsigned int estat;
348
349 estat = bcm_uart_readl(port, UART_EXTINP_REG);
350 if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS))
351 uart_handle_cts_change(port,
352 estat & UART_EXTINP_CTS_MASK);
353 if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD))
354 uart_handle_dcd_change(port,
355 estat & UART_EXTINP_DCD_MASK);
356 }
357
358 uart_unlock_and_check_sysrq(port);
359 return IRQ_HANDLED;
360 }
361
362 /*
363 * enable rx & tx operation on uart
364 */
bcm_uart_enable(struct uart_port * port)365 static void bcm_uart_enable(struct uart_port *port)
366 {
367 unsigned int val;
368
369 val = bcm_uart_readl(port, UART_CTL_REG);
370 val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK);
371 bcm_uart_writel(port, val, UART_CTL_REG);
372 }
373
374 /*
375 * disable rx & tx operation on uart
376 */
bcm_uart_disable(struct uart_port * port)377 static void bcm_uart_disable(struct uart_port *port)
378 {
379 unsigned int val;
380
381 val = bcm_uart_readl(port, UART_CTL_REG);
382 val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK |
383 UART_CTL_RXEN_MASK);
384 bcm_uart_writel(port, val, UART_CTL_REG);
385 }
386
387 /*
388 * clear all unread data in rx fifo and unsent data in tx fifo
389 */
bcm_uart_flush(struct uart_port * port)390 static void bcm_uart_flush(struct uart_port *port)
391 {
392 unsigned int val;
393
394 /* empty rx and tx fifo */
395 val = bcm_uart_readl(port, UART_CTL_REG);
396 val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK;
397 bcm_uart_writel(port, val, UART_CTL_REG);
398
399 /* read any pending char to make sure all irq status are
400 * cleared */
401 (void)bcm_uart_readl(port, UART_FIFO_REG);
402 }
403
404 /*
405 * serial core request to initialize uart and start rx operation
406 */
bcm_uart_startup(struct uart_port * port)407 static int bcm_uart_startup(struct uart_port *port)
408 {
409 unsigned int val;
410 int ret;
411
412 /* mask all irq and flush port */
413 bcm_uart_disable(port);
414 bcm_uart_writel(port, 0, UART_IR_REG);
415 bcm_uart_flush(port);
416
417 /* clear any pending external input interrupt */
418 (void)bcm_uart_readl(port, UART_EXTINP_REG);
419
420 /* set rx/tx fifo thresh to fifo half size */
421 val = bcm_uart_readl(port, UART_MCTL_REG);
422 val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK);
423 val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT;
424 val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT;
425 bcm_uart_writel(port, val, UART_MCTL_REG);
426
427 /* set rx fifo timeout to 1 char time */
428 val = bcm_uart_readl(port, UART_CTL_REG);
429 val &= ~UART_CTL_RXTMOUTCNT_MASK;
430 val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT;
431 bcm_uart_writel(port, val, UART_CTL_REG);
432
433 /* report any edge on dcd and cts */
434 val = UART_EXTINP_INT_MASK;
435 val |= UART_EXTINP_DCD_NOSENSE_MASK;
436 val |= UART_EXTINP_CTS_NOSENSE_MASK;
437 bcm_uart_writel(port, val, UART_EXTINP_REG);
438
439 /* register irq and enable rx interrupts */
440 ret = request_irq(port->irq, bcm_uart_interrupt, 0,
441 dev_name(port->dev), port);
442 if (ret)
443 return ret;
444 bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG);
445 bcm_uart_enable(port);
446 return 0;
447 }
448
449 /*
450 * serial core request to flush & disable uart
451 */
bcm_uart_shutdown(struct uart_port * port)452 static void bcm_uart_shutdown(struct uart_port *port)
453 {
454 unsigned long flags;
455
456 uart_port_lock_irqsave(port, &flags);
457 bcm_uart_writel(port, 0, UART_IR_REG);
458 uart_port_unlock_irqrestore(port, flags);
459
460 bcm_uart_disable(port);
461 bcm_uart_flush(port);
462 free_irq(port->irq, port);
463 }
464
465 /*
466 * serial core request to change current uart setting
467 */
bcm_uart_set_termios(struct uart_port * port,struct ktermios * new,const struct ktermios * old)468 static void bcm_uart_set_termios(struct uart_port *port, struct ktermios *new,
469 const struct ktermios *old)
470 {
471 unsigned int ctl, baud, quot, ier;
472 unsigned long flags;
473 int tries;
474
475 uart_port_lock_irqsave(port, &flags);
476
477 /* Drain the hot tub fully before we power it off for the winter. */
478 for (tries = 3; !bcm_uart_tx_empty(port) && tries; tries--)
479 mdelay(10);
480
481 /* disable uart while changing speed */
482 bcm_uart_disable(port);
483 bcm_uart_flush(port);
484
485 /* update Control register */
486 ctl = bcm_uart_readl(port, UART_CTL_REG);
487 ctl &= ~UART_CTL_BITSPERSYM_MASK;
488
489 switch (new->c_cflag & CSIZE) {
490 case CS5:
491 ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT);
492 break;
493 case CS6:
494 ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT);
495 break;
496 case CS7:
497 ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT);
498 break;
499 default:
500 ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT);
501 break;
502 }
503
504 ctl &= ~UART_CTL_STOPBITS_MASK;
505 if (new->c_cflag & CSTOPB)
506 ctl |= UART_CTL_STOPBITS_2;
507 else
508 ctl |= UART_CTL_STOPBITS_1;
509
510 ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
511 if (new->c_cflag & PARENB)
512 ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
513 ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
514 if (new->c_cflag & PARODD)
515 ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
516 bcm_uart_writel(port, ctl, UART_CTL_REG);
517
518 /* update Baudword register */
519 baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
520 quot = uart_get_divisor(port, baud) - 1;
521 bcm_uart_writel(port, quot, UART_BAUD_REG);
522
523 /* update Interrupt register */
524 ier = bcm_uart_readl(port, UART_IR_REG);
525
526 ier &= ~UART_IR_MASK(UART_IR_EXTIP);
527 if (UART_ENABLE_MS(port, new->c_cflag))
528 ier |= UART_IR_MASK(UART_IR_EXTIP);
529
530 bcm_uart_writel(port, ier, UART_IR_REG);
531
532 /* update read/ignore mask */
533 port->read_status_mask = UART_FIFO_VALID_MASK;
534 if (new->c_iflag & INPCK) {
535 port->read_status_mask |= UART_FIFO_FRAMEERR_MASK;
536 port->read_status_mask |= UART_FIFO_PARERR_MASK;
537 }
538 if (new->c_iflag & (IGNBRK | BRKINT))
539 port->read_status_mask |= UART_FIFO_BRKDET_MASK;
540
541 port->ignore_status_mask = 0;
542 if (new->c_iflag & IGNPAR)
543 port->ignore_status_mask |= UART_FIFO_PARERR_MASK;
544 if (new->c_iflag & IGNBRK)
545 port->ignore_status_mask |= UART_FIFO_BRKDET_MASK;
546 if (!(new->c_cflag & CREAD))
547 port->ignore_status_mask |= UART_FIFO_VALID_MASK;
548
549 uart_update_timeout(port, new->c_cflag, baud);
550 bcm_uart_enable(port);
551 uart_port_unlock_irqrestore(port, flags);
552 }
553
554 /*
555 * serial core request to claim uart iomem
556 */
bcm_uart_request_port(struct uart_port * port)557 static int bcm_uart_request_port(struct uart_port *port)
558 {
559 /* UARTs always present */
560 return 0;
561 }
562
563 /*
564 * serial core request to release uart iomem
565 */
bcm_uart_release_port(struct uart_port * port)566 static void bcm_uart_release_port(struct uart_port *port)
567 {
568 /* Nothing to release ... */
569 }
570
571 /*
572 * serial core request to do any port required autoconfiguration
573 */
bcm_uart_config_port(struct uart_port * port,int flags)574 static void bcm_uart_config_port(struct uart_port *port, int flags)
575 {
576 if (flags & UART_CONFIG_TYPE) {
577 if (bcm_uart_request_port(port))
578 return;
579 port->type = PORT_BCM63XX;
580 }
581 }
582
583 /*
584 * serial core request to check that port information in serinfo are
585 * suitable
586 */
bcm_uart_verify_port(struct uart_port * port,struct serial_struct * serinfo)587 static int bcm_uart_verify_port(struct uart_port *port,
588 struct serial_struct *serinfo)
589 {
590 if (port->type != PORT_BCM63XX)
591 return -EINVAL;
592 if (port->irq != serinfo->irq)
593 return -EINVAL;
594 if (port->iotype != serinfo->io_type)
595 return -EINVAL;
596 if (port->mapbase != (unsigned long)serinfo->iomem_base)
597 return -EINVAL;
598 return 0;
599 }
600
601 #ifdef CONFIG_CONSOLE_POLL
602 /*
603 * return true when outstanding tx equals fifo size
604 */
bcm_uart_tx_full(struct uart_port * port)605 static bool bcm_uart_tx_full(struct uart_port *port)
606 {
607 unsigned int val;
608
609 val = bcm_uart_readl(port, UART_MCTL_REG);
610 val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
611 return !(port->fifosize - val);
612 }
613
bcm_uart_poll_get_char(struct uart_port * port)614 static int bcm_uart_poll_get_char(struct uart_port *port)
615 {
616 unsigned int iestat;
617
618 iestat = bcm_uart_readl(port, UART_IR_REG);
619 if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
620 return NO_POLL_CHAR;
621
622 return bcm_uart_readl(port, UART_FIFO_REG);
623 }
624
bcm_uart_poll_put_char(struct uart_port * port,unsigned char c)625 static void bcm_uart_poll_put_char(struct uart_port *port, unsigned char c)
626 {
627 while (bcm_uart_tx_full(port)) {
628 cpu_relax();
629 }
630
631 bcm_uart_writel(port, c, UART_FIFO_REG);
632 }
633 #endif
634
635 /* serial core callbacks */
636 static const struct uart_ops bcm_uart_ops = {
637 .tx_empty = bcm_uart_tx_empty,
638 .get_mctrl = bcm_uart_get_mctrl,
639 .set_mctrl = bcm_uart_set_mctrl,
640 .start_tx = bcm_uart_start_tx,
641 .stop_tx = bcm_uart_stop_tx,
642 .stop_rx = bcm_uart_stop_rx,
643 .enable_ms = bcm_uart_enable_ms,
644 .break_ctl = bcm_uart_break_ctl,
645 .startup = bcm_uart_startup,
646 .shutdown = bcm_uart_shutdown,
647 .set_termios = bcm_uart_set_termios,
648 .type = bcm_uart_type,
649 .release_port = bcm_uart_release_port,
650 .request_port = bcm_uart_request_port,
651 .config_port = bcm_uart_config_port,
652 .verify_port = bcm_uart_verify_port,
653 #ifdef CONFIG_CONSOLE_POLL
654 .poll_get_char = bcm_uart_poll_get_char,
655 .poll_put_char = bcm_uart_poll_put_char,
656 #endif
657 };
658
659
660
661 #ifdef CONFIG_SERIAL_BCM63XX_CONSOLE
wait_for_xmitr(struct uart_port * port)662 static void wait_for_xmitr(struct uart_port *port)
663 {
664 unsigned int tmout;
665
666 /* Wait up to 10ms for the character(s) to be sent. */
667 tmout = 10000;
668 while (--tmout) {
669 unsigned int val;
670
671 val = bcm_uart_readl(port, UART_IR_REG);
672 if (val & UART_IR_STAT(UART_IR_TXEMPTY))
673 break;
674 udelay(1);
675 }
676
677 /* Wait up to 1s for flow control if necessary */
678 if (port->flags & UPF_CONS_FLOW) {
679 tmout = 1000000;
680 while (--tmout) {
681 unsigned int val;
682
683 val = bcm_uart_readl(port, UART_EXTINP_REG);
684 if (val & UART_EXTINP_CTS_MASK)
685 break;
686 udelay(1);
687 }
688 }
689 }
690
691 /*
692 * output given char
693 */
bcm_console_putchar(struct uart_port * port,unsigned char ch)694 static void bcm_console_putchar(struct uart_port *port, unsigned char ch)
695 {
696 wait_for_xmitr(port);
697 bcm_uart_writel(port, ch, UART_FIFO_REG);
698 }
699
700 /*
701 * console core request to output given string
702 */
bcm_console_write(struct console * co,const char * s,unsigned int count)703 static void bcm_console_write(struct console *co, const char *s,
704 unsigned int count)
705 {
706 struct uart_port *port;
707 unsigned long flags;
708 int locked = 1;
709
710 port = &ports[co->index];
711
712 if (oops_in_progress)
713 locked = uart_port_trylock_irqsave(port, &flags);
714 else
715 uart_port_lock_irqsave(port, &flags);
716
717 /* call helper to deal with \r\n */
718 uart_console_write(port, s, count, bcm_console_putchar);
719
720 /* and wait for char to be transmitted */
721 wait_for_xmitr(port);
722
723 if (locked)
724 uart_port_unlock_irqrestore(port, flags);
725 }
726
727 /*
728 * console core request to setup given console, find matching uart
729 * port and setup it.
730 */
bcm_console_setup(struct console * co,char * options)731 static int bcm_console_setup(struct console *co, char *options)
732 {
733 struct uart_port *port;
734 int baud = 9600;
735 int bits = 8;
736 int parity = 'n';
737 int flow = 'n';
738
739 if (co->index < 0 || co->index >= BCM63XX_NR_UARTS)
740 return -EINVAL;
741 port = &ports[co->index];
742 if (!port->membase)
743 return -ENODEV;
744 if (options)
745 uart_parse_options(options, &baud, &parity, &bits, &flow);
746
747 return uart_set_options(port, co, baud, parity, bits, flow);
748 }
749
750 static struct uart_driver bcm_uart_driver;
751
752 static struct console bcm63xx_console = {
753 .name = "ttyS",
754 .write = bcm_console_write,
755 .device = uart_console_device,
756 .setup = bcm_console_setup,
757 .flags = CON_PRINTBUFFER,
758 .index = -1,
759 .data = &bcm_uart_driver,
760 };
761
bcm63xx_console_init(void)762 static int __init bcm63xx_console_init(void)
763 {
764 register_console(&bcm63xx_console);
765 return 0;
766 }
767
768 console_initcall(bcm63xx_console_init);
769
bcm_early_write(struct console * con,const char * s,unsigned n)770 static void bcm_early_write(struct console *con, const char *s, unsigned n)
771 {
772 struct earlycon_device *dev = con->data;
773
774 uart_console_write(&dev->port, s, n, bcm_console_putchar);
775 wait_for_xmitr(&dev->port);
776 }
777
bcm_early_console_setup(struct earlycon_device * device,const char * opt)778 static int __init bcm_early_console_setup(struct earlycon_device *device,
779 const char *opt)
780 {
781 if (!device->port.membase)
782 return -ENODEV;
783
784 device->con->write = bcm_early_write;
785 return 0;
786 }
787
788 OF_EARLYCON_DECLARE(bcm63xx_uart, "brcm,bcm6345-uart", bcm_early_console_setup);
789
790 #define BCM63XX_CONSOLE (&bcm63xx_console)
791 #else
792 #define BCM63XX_CONSOLE NULL
793 #endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */
794
795 static struct uart_driver bcm_uart_driver = {
796 .owner = THIS_MODULE,
797 .driver_name = "bcm63xx_uart",
798 .dev_name = "ttyS",
799 .major = TTY_MAJOR,
800 .minor = 64,
801 .nr = BCM63XX_NR_UARTS,
802 .cons = BCM63XX_CONSOLE,
803 };
804
805 /*
806 * platform driver probe/remove callback
807 */
bcm_uart_probe(struct platform_device * pdev)808 static int bcm_uart_probe(struct platform_device *pdev)
809 {
810 struct resource *res_mem;
811 struct uart_port *port;
812 struct clk *clk;
813 int ret;
814
815 if (pdev->dev.of_node) {
816 pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
817
818 if (pdev->id < 0)
819 pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
820 }
821
822 if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS)
823 return -EINVAL;
824
825 port = &ports[pdev->id];
826 if (port->membase)
827 return -EBUSY;
828 memset(port, 0, sizeof(*port));
829
830 port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res_mem);
831 if (IS_ERR(port->membase))
832 return PTR_ERR(port->membase);
833 port->mapbase = res_mem->start;
834
835 ret = platform_get_irq(pdev, 0);
836 if (ret < 0)
837 return ret;
838 port->irq = ret;
839
840 clk = clk_get(&pdev->dev, "refclk");
841 if (IS_ERR(clk) && pdev->dev.of_node)
842 clk = of_clk_get(pdev->dev.of_node, 0);
843
844 if (IS_ERR(clk))
845 return -ENODEV;
846
847 port->iotype = UPIO_MEM;
848 port->ops = &bcm_uart_ops;
849 port->flags = UPF_BOOT_AUTOCONF;
850 port->dev = &pdev->dev;
851 port->fifosize = 16;
852 port->uartclk = clk_get_rate(clk) / 2;
853 port->line = pdev->id;
854 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_BCM63XX_CONSOLE);
855 clk_put(clk);
856
857 ret = uart_add_one_port(&bcm_uart_driver, port);
858 if (ret) {
859 ports[pdev->id].membase = NULL;
860 return ret;
861 }
862 platform_set_drvdata(pdev, port);
863 return 0;
864 }
865
bcm_uart_remove(struct platform_device * pdev)866 static void bcm_uart_remove(struct platform_device *pdev)
867 {
868 struct uart_port *port;
869
870 port = platform_get_drvdata(pdev);
871 uart_remove_one_port(&bcm_uart_driver, port);
872 /* mark port as free */
873 ports[pdev->id].membase = NULL;
874 }
875
876 static const struct of_device_id bcm63xx_of_match[] = {
877 { .compatible = "brcm,bcm6345-uart" },
878 { /* sentinel */ }
879 };
880 MODULE_DEVICE_TABLE(of, bcm63xx_of_match);
881
882 /*
883 * platform driver stuff
884 */
885 static struct platform_driver bcm_uart_platform_driver = {
886 .probe = bcm_uart_probe,
887 .remove_new = bcm_uart_remove,
888 .driver = {
889 .name = "bcm63xx_uart",
890 .of_match_table = bcm63xx_of_match,
891 },
892 };
893
bcm_uart_init(void)894 static int __init bcm_uart_init(void)
895 {
896 int ret;
897
898 ret = uart_register_driver(&bcm_uart_driver);
899 if (ret)
900 return ret;
901
902 ret = platform_driver_register(&bcm_uart_platform_driver);
903 if (ret)
904 uart_unregister_driver(&bcm_uart_driver);
905
906 return ret;
907 }
908
bcm_uart_exit(void)909 static void __exit bcm_uart_exit(void)
910 {
911 platform_driver_unregister(&bcm_uart_platform_driver);
912 uart_unregister_driver(&bcm_uart_driver);
913 }
914
915 module_init(bcm_uart_init);
916 module_exit(bcm_uart_exit);
917
918 MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
919 MODULE_DESCRIPTION("Broadcom 63xx integrated uart driver");
920 MODULE_LICENSE("GPL");
921