Lines Matching +full:fpga +full:- +full:slave +full:- +full:serial
1 /* SPDX-License-Identifier: GPL-2.0-or-later */
16 #include <sound/pcm-indirect.h>
25 /* ------------------- DEFINES -------------------- */
33 /* FIXME? - according to the OSS driver the EMU10K1 needs a 29 bit DMA mask */
41 // This is used to define hardware bit-fields (sub-registers) by combining
44 // The non-concatenating (_NC) variant should be used directly only for
45 // sub-registers that do not follow the <register>_<field> naming pattern.
55 // Macros for manipulating values of bit-fields declared using the above macros.
59 // single sub-register at a time.
62 #define REG_MASK0(r) ((1U << REG_SIZE(r)) - 1U)
79 #define PTR_CHANNELNUM_MASK 0x0000003f /* For each per-channel register, indicates the */
81 /* accessed. For non per-channel registers the */
117 #define IPR_CDROMSTATUSCHANGE 0x00000400 /* CD-ROM channel status change */
134 #define INTE_VIRTUALSB_220 0x00000000 /* Capture at I/O base address 0x220-0x22f */
139 #define INTE_VIRTUALMPU_300 0x00000000 /* Capture at I/O base address 0x300-0x301 */
143 #define INTE_MASTERDMAENABLE 0x08000000 /* Master DMA emulation at 0x000-0x00f */
144 #define INTE_SLAVEDMAENABLE 0x04000000 /* Slave DMA emulation at 0x0c0-0x0df */
145 #define INTE_MASTERPICENABLE 0x02000000 /* Master PIC emulation at 0x020-0x021 */
146 #define INTE_SLAVEPICENABLE 0x01000000 /* Slave PIC emulation at 0x0a0-0x0a1 */
148 #define INTE_ADLIBENABLE 0x00400000 /* Enable AdLib emulation at 0x388-0x38b */
161 #define INTE_A_MIDITXENABLE2 0x00020000 /* Enable MIDI transmit-buffer-empty interrupts */
162 #define INTE_A_MIDIRXENABLE2 0x00010000 /* Enable MIDI receive-buffer-empty interrupts */
180 #define INTE_MIDITXENABLE 0x00000002 /* Enable MIDI transmit-buffer-empty interrupts */
181 #define INTE_MIDIRXENABLE 0x00000001 /* Enable MIDI receive-buffer-empty interrupts */
215 #define HCFG_CODECFORMAT_AC97_1 0x00000000 /* AC97 CODEC format -- Ver 1.03 */
216 #define HCFG_CODECFORMAT_AC97_2 0x00010000 /* AC97 CODEC format -- Ver 2.1 */
219 /* they are not rate-locked to the external */
223 /* the SPDIF V-bit indicates invalid audio */
224 #define HCFG_EMU32_SLAVE 0x00002000 /* 0 = Master, 1 = Slave. Slave for EMU1010 */
237 #define HCFG_CODECFORMAT_AC97 0x00000000 /* AC97 CODEC format -- Primary Output */
238 #define HCFG_CODECFORMAT_I2S 0x00010000 /* I2S CODEC format -- Secondary (Rear) Output */
249 #define HCFG_AC3ENABLE_MASK 0x000000e0 /* AC3 async input control - Not implemented */
255 /* they are not rate-locked to the external */
267 #define HCFG_AUDIOENABLE 0x00000001 /* 0 = CODECs transmit zero-valued samples */
271 // On Audigy, the MPU port moved to the 0x70-0x74 ptr registers
290 // card-specific info can be found in the emu_chip_details table.
291 // On E-MU cards the port is used as the interface to the FPGA.
300 #define A_IOCFG_DISABLE_AC97_FRONT 0x0080 /* turn off ac97 front -> front (10k2.1) */
320 #define AC97ADDRESS_READY 0x80 /* Read-only bit, reflects CODEC READY signal */
346 /* 0x00000000 2-channel output. */
347 /* 0x00000200 8-channel output. */
354 * bit 8: Record 8-channel in phase.
355 * bit 9: Playback 8-channel in phase.
356 * bit 11-12: Playback mixer attenuation: 0=0dB, 1=-6dB, 2=-12dB, 3=Mute.
383 /* Emu10k1 pointer-offset register set, accessed through the PTR and DATA registers */
388 // "AWE32/EMU8000 Programmer’s Guide" (emu8kpgm.pdf) - registers
389 // "AWE32 Developer's Information Pack" (adip301.pdf) - high-level view
392 // - The engine has 64 playback channels, also called voices. The channels
394 // - PCM samples are fetched into the cache; see description of CD0 below.
395 // - Samples are consumed at the rate CPF_CURRENTPITCH.
396 // - 8-bit samples are transformed upon use: cooked = (raw ^ 0x80) << 8
397 // - 8 samples are read at CCR_READADDRESS:CPF_FRACADDRESS and interpolated
400 // - The value is multiplied by CVCF_CURRENTVOL.
401 // - The value goes through a filter with cutoff CVCF_CURRENTFILTER;
403 // - The value is added by so-called `sends` to 4 (EMU10K1) / 8 (EMU10K2)
405 // multiplied by a per-send amount (*_FXSENDAMOUNT_*).
406 // The scaling of the send amounts is exponential-ish.
407 // - The DSP has a go at FXBUS* and outputs the values to EXTOUT* or EMU32OUT*.
408 // - The pitch, volume, and filter cutoff can be modulated by two envelope
410 // - To avoid abrupt changes to the parameters (which may cause audible
417 // The somewhat non-obviously still meaningful ones are:
471 #define CCCA_8BITSELECT 0x01000000 /* 1 = Sound memory for this channel uses 8-bit samples */
472 /* 8-bit samples are unsigned, 16-bit ones signed */
479 /* Auto-set from CPF_STEREO_MASK */
481 /* Auto-set from CCCA_8BITSELECT */
513 /* 0x8000-n == 666*n usec delay */
517 #define ATKHLDV_HOLDTIME_MASK 0x00007f00 /* Envelope hold time (127-n == n*88.2msec) */
532 /* 0x8000-n == 666*n usec delay */
536 /* 0x8000-n == 666*n usec delay */
540 #define ATKHLDM_HOLDTIME 0x00007f00 /* Envelope hold time (127-n == n*42msec) */
552 /* 0x8000-n == 666*n usec delay */
567 /* Signed 2's complement, +/- one octave peak extremes */
569 /* Signed 2's complement, +/- six octaves peak extremes */
574 /* Signed 2's complement, +/- one octave extremes */
576 /* Signed 2's complement, +/- three octave extremes */
580 /* Signed 2's complement, with +/- 12dB extremes */
586 /* Signed 2's complement, +/- one octave extremes */
591 #define TEMPENV_MASK 0x0000ffff /* 16-bit value */
600 // The cache holds 64 frames, so the upper half is not used in 8-bit mode.
607 // The cache is filled from (CA - CIS) into (CRA - CIS).
609 // CIS below 8 (16-bit stereo), 16 (16-bit mono, 8-bit stereo), or
610 // 32 (8-bit mono). The actual transfers are pretty unpredictable,
619 // filled from (CLA - LIS), and CLF is subsequently reset.
653 /* 0x20-0x3f) to host memory. This mode of recording */
679 #define A_HWM 0x48 /* High PCI Water Mark - word access, defaults to 3f */
728 // NOTE: 0x50,51,52: 64-bit (split over voices 0 & 1)
729 #define CDCS 0x50 /* CD-ROM digital channel status register */
743 // NOTE: 0x54,55,56: 64-bit (split over voices 0 & 1)
764 #define SPCS_GENERATIONSTATUS 0x00008000 /* Originality flag (see IEC-958 spec) */
765 #define SPCS_CATEGORYCODEMASK 0x00007f00 /* Category code (see IEC-958 spec) */
766 #define SPCS_MODEMASK 0x000000c0 /* Mode (see IEC-958 spec) */
770 #define SPCS_COPYRIGHT 0x00000004 /* Copyright asserted flag -- do not modify */
772 #define SPCS_PROFESSIONAL 0x00000001 /* 0 = Consumer (IEC-958), 1 = pro (AES3-1992) */
776 /* The 32-bit CLIx and SOLEx registers all have one bit per channel control/status */
792 /* bypass mode: 0 - DSP; 1 - SPDIF A, 2 - SPDIF B, 3 - SPDIF C */
793 #define SPBYPASS_FORMAT 0x00000f00 /* If 1, SPDIF XX uses 24 bit, if 0 - 20 bit */
803 // NOTE: 0x60,61,62: 64-bit
804 #define CDSRCS 0x60 /* CD-ROM Sample Rate Converter status register */
818 /* Note that these values can vary +/- by a small amount */
838 /* The 32-bit HLIEx and HLIPx registers all have one bit per channel control/status */
867 #define A_FXWC1 0x74 /* Selects 0x7f-0x60 for FX recording */
868 #define A_FXWC2 0x75 /* Selects 0x9f-0x80 for FX recording */
905 /* - default to 0x01080000 on my audigy 2 ZS --rlrevell */
949 /* E-MU Digital Audio System overview */
952 // - These cards use a regular PCI-attached Audigy chip (Alice2/Tina/Tina2);
954 // - All physical PCM I/O is routed through an additional FPGA; the regular
956 // - The FPGA has a signal routing matrix, to connect each destination (output
958 // - The FPGA is controlled via Audigy's GPIO port, while sample data is
959 // transmitted via proprietary EMU32 serial links. On first-generation
960 // E-MU 1010 cards, Audigy's I2S inputs are also used for sample data.
961 // - The Audio/Micro Dock is attached to Hana via EDI, a "network" link.
962 // - The Audigy chip operates in slave mode; the clock is supplied by the FPGA.
963 // Gen1 E-MU 1010 cards have two crystals (for 44.1 kHz and 48 kHz multiples),
965 // - The whole card is switched to 2x/4x mode to achieve 88.2/96/176.4/192 kHz
968 // - The number of available EMU32/EDI channels is hit in 2x/4x mode, so the total
970 // - S/PDIF is unavailable in 4x mode (only over TOSLINK on newer 1010 cards) due
973 // - The code names are mentioned below and in the emu_chip_details table.
976 /* EMU1010 FPGA registers */
1018 #define EMU_HANA_FPGA_CONFIG_AUDIODOCK 0x01 /* Set in order to program FPGA on Audio Dock */
1019 #define EMU_HANA_FPGA_CONFIG_HANA 0x02 /* Set in order to program FPGA on Hana */
1044 #define EMU_HANA_MIDI_INA_FROM_DOCK1 0x02 /* Audio Dock-1 MIDI in to Alice 2 MIDI A */
1045 #define EMU_HANA_MIDI_INA_FROM_DOCK2 0x03 /* Audio Dock-2 MIDI in to Alice 2 MIDI A */
1047 #define EMU_HANA_MIDI_INB_FROM_DOCK1 0x10 /* Audio Dock-1 MIDI in to Alice 2 MIDI B */
1048 #define EMU_HANA_MIDI_INB_FROM_DOCK2 0x18 /* Audio Dock-2 MIDI in to Alice 2 MIDI B */
1102 /* 0x14 - 0x1f Unused R/W registers */
1111 #define EMU_HANA_OPTION_DOCK_ONLINE 0x04 /* Audio/Micro dock present and FPGA configured */
1112 #define EMU_HANA_OPTION_DOCK_OFFLINE 0x08 /* Audio/Micro dock present and FPGA not configured */
1117 #define EMU_HANA_MAJOR_REV 0x23 /* 0000xxx 3 bit Hana FPGA Major rev */
1118 #define EMU_HANA_MINOR_REV 0x24 /* 0000xxx 3 bit Hana FPGA Minor rev */
1120 #define EMU_DOCK_MAJOR_REV 0x25 /* 0000xxx 3 bit Audio Dock FPGA Major rev */
1121 #define EMU_DOCK_MINOR_REV 0x26 /* 0000xxx 3 bit Audio Dock FPGA Minor rev */
1127 // The actual code disagrees about the bit width of the registers -
1142 /* 0x30 - 0x3f Unused Read only registers */
1144 // The meaning of this is not clear; kX-project just calls it "lock" in some info-only code.
1152 * 0x00, 0x00-0x0f: 16 EMU32 channels to Alice2
1153 * 0x01, 0x00-0x1f: 32 EDI channels to Audio Dock
1170 * 0x04, 0x00-0x07: Hana ADAT
1182 * 0x00, 0x00-0x0f: 16 EMU32A channels to Tina
1183 * 0x01, 0x00-0x1f: 32 EDI channels to Micro Dock
1192 * 0x18-0x1f: Dock ADAT 0-7
1197 * 0x04, 0x00-0x07: Hana3 ADAT 0-7
1198 * 0x05, 0x00-0x0f: 16 EMU32B channels to Tina
1199 * 0x06-0x07: Not used
1203 * 0x00, 0x00-0x0f: 16 EMU32 channels to Alice2/Tina
1209 * 0x04-0x07: Not used
1212 * 0x00, 0x00-0x0f: 16 EMU32A channels to Tina2
1213 * 0x01, 0x00-0x1f: 32 EDI channels to Micro Dock
1218 * 0x04, 0x00-0x0f: 16 EMU32B channels to Tina2
1219 * 0x05-0x07: Not used
1222 /* 32-bit destinations of signal in the Hana FPGA. Destinations are either
1223 * physical outputs of Hana, or outputs going to Alice2/Tina for capture -
1225 * a channel depends on the mixer control setting for each destination - see
1325 * 0x00, 0x00-0x1f: Silence
1326 * 0x01, 0x00-0x1f: 32 EDI channels from Audio Dock
1337 * 0x03, 0x00-0x0f: 16 inputs from Alice2 Emu32A output
1338 * 0x03, 0x10-0x1f: 16 inputs from Alice2 Emu32B output
1339 * 0x04, 0x00-0x07: Hana ADAT
1342 * 0x06-0x07: Not used
1348 * 0x00, 0x00-0x1f: Silence
1349 * 0x01, 0x00-0x1f: 32 EDI channels from Micro Dock
1358 * 0x18-0x1f: Dock ADAT 0-7
1361 * 0x03, 0x00-0x0f: 16 inputs from Tina Emu32A output
1362 * 0x03, 0x10-0x1f: 16 inputs from Tina Emu32B output
1363 * 0x04, 0x00-0x07: Hana3 ADAT
1366 * 0x06-0x07: Not used
1370 * 0x00, 0x00-0x1f: Silence
1374 * 0x03, 0x00-0x0f: 16 inputs from Alice2/Tina Emu32A output
1375 * 0x03, 0x10-0x1f: 16 inputs from Alice2/Tina Emu32B output
1379 * 0x06-0x07: Not used
1382 * 0x00, 0x00-0x1f: Silence
1383 * 0x01, 0x00-0x1f: 32 EDI channels from Micro Dock
1386 * 0x03, 0x00-0x0f: 16 inputs from Tina2 Emu32A output
1387 * 0x03, 0x10-0x1f: 16 inputs from Tina2 Emu32B output
1388 * 0x04-0x07: Not used
1391 /* 32-bit sources of signal in the Hana FPGA. The sources are routed to
1392 * destinations using a mixer control for each destination - see emumixer.c.
1393 * Sources are either physical inputs of Hana, or inputs from Alice2/Tina -
1461 /* ------------------- CONSTANTS -------------------- */
1470 /* ------------------- STRUCTURES -------------------- */
1557 …efine snd_emu10k1_memblk_offset(blk) (((blk)->mapped_page << PAGE_SHIFT) | ((blk)->mem.offset & (P…
1586 unsigned int channels; /* 16-bit channels count */
1641 // Chip-o-logy:
1642 // - All SB Live! cards use EMU10K1 chips
1643 // - All SB Audigy cards use CA* chips, termed "emu10k2" by the driver
1644 // - Original Audigy uses CA0100 "Alice"
1645 // - Audigy 2 uses CA0102/CA10200 "Alice2"
1646 // - Has an interface for CA0151 (P16V) "Alice3"
1647 // - Audigy 2 Value uses CA0108/CA10300 "Tina"
1648 // - Approximately a CA0102 with an on-chip CA0151 (P17V)
1649 // - Audigy 2 ZS NB uses CA0109 "Tina2"
1650 // - Cardbus version of CA0108
1668 unsigned int sblive51:1; /* SBLive! 5.1 - extout 0x11 -> center, 0x12 -> lfe */
1678 const char *id; /* for backward compatibility - can be NULL if not needed */
1711 unsigned int serial; /* serial number */ member
1752 spinlock_t reg_lock; // high-level driver lock
1753 spinlock_t emu_lock; // low-level i/o lock
1845 static inline void snd_emu1010_fpga_lock(struct snd_emu10k1 *emu) { mutex_lock(&emu->emu1010.lock);… in snd_emu1010_fpga_lock()
1846 static inline void snd_emu1010_fpga_unlock(struct snd_emu10k1 *emu) { mutex_unlock(&emu->emu1010.lo… in snd_emu1010_fpga_unlock()
1872 static inline unsigned int snd_emu10k1_wc(struct snd_emu10k1 *emu) { return (inl(emu->port + WC) >>… in snd_emu10k1_wc()