1 /* SPDX-License-Identifier: GPL-2.0-only */
3  * mac80211 <-> driver interface
5  * Copyright 2002-2005, Devicescape Software, Inc.
6  * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
7  * Copyright 2007-2010	Johannes Berg <johannes@sipsolutions.net>
8  * Copyright 2013-2014  Intel Mobile Communications GmbH
9  * Copyright (C) 2015 - 2017 Intel Deutschland GmbH
10  * Copyright (C) 2018 - 2025 Intel Corporation
31  * only partial functionality in hard- or firmware. This document
32  * defines the interface between mac80211 and low-level hardware
40  * called in hardware interrupt context. The low-level driver must not call any
42  * call, the low-level driver should first ACK the interrupt and perform the
47  *	 use the non-IRQ-safe functions!
100  * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with
101  * another per-sta for non-data/non-mgmt and bufferable management frames, and
102  * a single per-vif queue for multicast data frames.
104  * The driver is expected to initialize its private per-queue data for stations
149  * enum ieee80211_max_queues - maximum number of queues
156 	IEEE80211_MAX_QUEUE_MAP =	BIT(IEEE80211_MAX_QUEUES) - 1,
162  * enum ieee80211_ac_numbers - AC numbers as used in mac80211
176  * struct ieee80211_tx_queue_params - transmit queue configuration
183  *	2^n-1 in the range 1..32767]
187  * @uapsd: is U-APSD mode enabled for the queue
210  * enum ieee80211_chanctx_change - change flag for channel context
233  * struct ieee80211_chan_req - A channel "request"
244  * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
246  * This is the driver-visible part. The ieee80211_chanctx
277  * enum ieee80211_chanctx_switch_mode - channel context switch mode
285  *      implement this as an on-the-fly chandef switch of the existing
296  * struct ieee80211_vif_chanctx_switch - vif chanctx switch information
316  * enum ieee80211_bss_change - BSS change notification flags
353  * @BSS_CHANGED_MU_GROUPS: VHT MU-MIMO group id or user position changed
417  * enum ieee80211_event_type - event to be notified to the low level driver
433  * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT
443  * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT
451  * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT
465  * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT
477  * struct ieee80211_mlme_event - data attached to an %MLME_EVENT
489  * struct ieee80211_ba_event - data attached for BlockAck related events
501  * struct ieee80211_event - event to be sent to the driver
518  * struct ieee80211_mu_group_data - STA's VHT MU-MIMO group data
520  * This structure describes the group id data of VHT MU-MIMO
522  * @membership: 64 bits array - a bit is set if station is member of the group
531  * struct ieee80211_ftm_responder_params - FTM responder parameters
546  * struct ieee80211_fils_discovery - FILS discovery parameters from
547  * IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
549  * @min_interval: Minimum packet interval in TUs (0 - 10000)
550  * @max_interval: Maximum packet interval in TUs (0 - 10000)
572  * struct ieee80211_parsed_tpe - parsed transmit power envelope information
591  * struct ieee80211_bss_conf - holds the BSS's changing parameters
602  * @link_id: link ID, or 0 for non-MLO
619  *	with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
642  * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
645  * @chanreq: Channel request for this BSS -- the hardware might be
647  * @mu_group: VHT MU-MIMO group membership data
661  * @qos: This is a QoS-enabled BSS.
662  * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
686  *	if MBSSID is enabled. This pointer is RCU-protected due to CSA finish
710  * @mu_mimo_owner: indicates interface owns MU-MIMO capability
712  *	when it is not assigned. This pointer is RCU-protected due to the TX
729  * @he_su_beamformer: in AP-mode, does this BSS support operation as an HE SU
731  * @he_su_beamformee: in AP-mode, does this BSS support operation as an HE SU
733  * @he_mu_beamformer: in AP-mode, does this BSS support operation as an HE MU
736  *	(non-AP STA) of an HE TB PPDU on an RU that spans the entire PPDU
738  * @eht_su_beamformer: in AP-mode, does this BSS enable operation as an EHT SU
740  * @eht_su_beamformee: in AP-mode, does this BSS enable operation as an EHT SU
742  * @eht_mu_beamformer: in AP-mode, does this BSS enable operation as an EHT MU
744  * @eht_80mhz_full_bw_ul_mumimo: in AP-mode, does this BSS support the
747  * @eht_disable_mcs15: disable EHT-MCS 15 reception capability.
748  * @bss_param_ch_cnt: in BSS-mode, the BSS params change count. This
751  * @bss_param_ch_cnt_link_id: in BSS-mode, the link_id to which the beacon
754  *	link 1's BSS params change count, then, link 1's
820 		u32 params;  member
867  * enum mac80211_tx_info_flags - flags to describe transmission information/status
876  *	assign sequence numbers to QoS-data frames but cannot do so correctly
877  *	for non-QoS-data and management frames because beacons need them from
881  *	802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
888  * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
909  *	off-channel operation.
917  *	frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
933  * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
936  *	the off-channel channel when a remain-on-channel offload is done
937  *	in hardware -- normal packets still flow and are expected to be
949  *	PS-Poll responses.
959  *	This flag must not be set for frames that don't request no-ack
1004  * enum mac80211_tx_control_flags - flags to describe transmit control
1009  *	frame (PS-Poll or uAPSD).
1011  * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame
1034  * These flags are used in tx_info->control.flags.
1057  * enum mac80211_tx_status_flags - flags to describe transmit status
1061  * These flags are used in tx_info->status.flags.
1081  * enum mac80211_rate_control_flags - per-rate flags set by the
1088  * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
1135  * struct ieee80211_tx_rate - rate selection/status
1141  * A value of -1 for @idx indicates an invalid rate and, if used
1142  * in an array of retry rates, that no more rates should be tried.
1153  *    { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
1161  *   { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
1176 	return rate->idx >= 0 && rate->count > 0;  in ieee80211_rate_valid()
1183 	WARN_ON((nss - 1) & ~0x7);  in ieee80211_rate_set_vht()
1184 	rate->idx = ((nss - 1) << 4) | mcs;  in ieee80211_rate_set_vht()
1190 	return rate->idx & 0xF;  in ieee80211_rate_get_vht_mcs()
1196 	return (rate->idx >> 4) + 1;  in ieee80211_rate_get_vht_nss()
1200  * struct ieee80211_tx_info - skb transmit information
1202  * This structure is placed in skb->cb for three uses:
1203  *  (1) mac80211 TX control - mac80211 tells the driver what to do
1205  *  (3) TX status information - driver tells mac80211 what happened
1314 	 * in increments of 4us and clamp the maximum to 2**12-1  in ieee80211_info_set_tx_time_est()
1316 	info->tx_time_est = min_t(u16, tx_time_est, 4095) >> 2;  in ieee80211_info_set_tx_time_est()
1317 	return info->tx_time_est << 2;  in ieee80211_info_set_tx_time_est()
1323 	return info->tx_time_est << 2;  in ieee80211_info_get_tx_time_est()
1327  * struct ieee80211_rate_status - mrr stage for status path
1334  * @tx_power_idx An idx into the ieee80211_hw->tx_power_levels list of the
1345  * struct ieee80211_tx_status - extended tx status info for rate control
1369  * struct ieee80211_scan_ies - descriptors for different blocks of IEs
1390 	return (struct ieee80211_tx_info *)skb->cb;  in IEEE80211_SKB_CB()
1395 	return (struct ieee80211_rx_status *)skb->cb;  in IEEE80211_SKB_RXCB()
1399  * ieee80211_tx_info_clear_status - clear TX status
1424 		info->status.rates[i].count = 0;  in ieee80211_tx_info_clear_status()
1425 	memset_after(&info->status, 0, rates);  in ieee80211_tx_info_clear_status()
1430  * enum mac80211_rx_flags - receive flags
1442  *	flag indicates that the PN was verified for replay protection.
1446  *	de-duplication by itself.
1452  *	field) is valid if this field is non-zero, and the position
1469  *	Valid only for data frames (mainly A-MPDU)
1470  * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
1472  *	each A-MPDU
1474  *	subframes of a single A-MPDU
1475  * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
1488  * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
1490  *	All, but the last MSDU from an A-MSDU should have this flag set. E.g.
1491  *	if an A-MSDU has 3 frames, the first 2 must have the flag set, while
1493  *	deal with retransmission/duplication recovery properly since A-MSDU
1495  *	either regular MSDU or singly A-MSDUs. Subframes must not be
1498  *	skb->data (before the 802.11 header).
1503  * @RX_FLAG_ALLOW_SAME_PN: Allow the same PN as same packet before.
1504  *	This is used for AMSDU subframes which can have the same PN as
1508  * @RX_FLAG_AMPDU_EOF_BIT: Value of the EOF bit in the A-MPDU delimiter for this
1514  *	 - DATA3_DATA_MCS
1515  *	 - DATA3_DATA_DCM
1516  *	 - DATA3_CODING
1517  *	 - DATA5_GI
1518  *	 - DATA5_DATA_BW_RU_ALLOC
1519  *	 - DATA6_NSTS
1520  *	 - DATA3_STBC
1525  * @RX_FLAG_RADIOTAP_LSIG: L-SIG radiotap data is present
1527  *	the "0-length PSDU" field included there.  The value for it is
1570  * enum mac80211_rx_encoding_flags - MCS & bandwidth flags
1574  * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission,
1579  * @RX_ENC_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
1602  * struct ieee80211_rx_status - receive status
1604  * The low-level driver should provide this information (the subset
1608  * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1620  *	for data (other) frames - for those it only affects radiotap reporting.
1627  * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
1644  * @ampdu_reference: A-MPDU reference number, must be a different value for
1645  *	each A-MPDU but the same for each subframe within one A-MPDU
1646  * @zero_length_psdu_type: radiotap type of the 0-length PSDU
1690 	return MHZ_TO_KHZ(rx_status->freq) +  in ieee80211_rx_status_to_khz()
1691 	       (rx_status->freq_offset ? 500 : 0);  in ieee80211_rx_status_to_khz()
1695  * enum ieee80211_conf_flags - configuration flags
1699  * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
1703  *	This is the power save mode defined by IEEE 802.11-2007 section 11.2,
1726  * enum ieee80211_conf_changed - denotes which configuration changed
1733  * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
1751  * enum ieee80211_smps_mode - spatial multiplexing power save mode
1770  * struct ieee80211_conf - configuration of the device
1818  * struct ieee80211_channel_switch - holds the channel switch data
1823  * @timestamp: value in microseconds of the 64-bit Time Synchronization
1836  * @link_id: the link ID of the link doing the channel switch, 0 for non-MLO
1849  * enum ieee80211_vif_flags - virtual interface flags
1854  *	monitoring on this virtual interface -- i.e. it can monitor
1857  * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this
1869  *	handle OFDMA (downlink and trigger for uplink) on a per-AP basis.
1886  * enum ieee80211_offload_flags - virtual interface offload flags
1891  * @IEEE80211_OFFLOAD_ENCAP_4ADDR: support 4-address mode encapsulation offload
1904  * struct ieee80211_vif_cfg - interface configuration
1908  * @ps: power-save mode (STA only). This flag is NOT affected by
1911  * @eml_cap: EML capabilities as described in P802.11be_D4.1 Figure 9-1001j.
1913  *	P802.11be_D4.1 Figure 9-1001i.
1915  *	Figure 9-1001k
1929  * @ap_addr: AP MLD address, or BSSID for non-MLO connections
1954  * struct ieee80211_neg_ttlm - negotiated TID to link map info
1969  * enum ieee80211_neg_ttlm_res - return value for negotiated TTLM handling
1981  * struct ieee80211_vif - per-interface data
1990  * @link_conf: in case of MLD, the per-link BSS configuration,
1992  * @valid_links: bitmap of valid links, or 0 for non-MLO.
1993  * @active_links: The bitmap of active links, or 0 for non-MLO.
1998  *	0 for non-MLO.
2002  *	0 for non-MLO.
2009  *	interface, i.e. a GO or p2p-sta respectively
2011  *	vif. mac80211 initializes this to hw->netdev_features, and the driver
2024  * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
2035  * @offload_flags: 802.3 -> 802.11 enapsulation offload flags, see
2070  * ieee80211_vif_usable_links - Return the usable links for the vif
2076 	return vif->valid_links & ~vif->dormant_links;  in ieee80211_vif_usable_links()
2080  * ieee80211_vif_is_mld - Returns true iff the vif is an MLD one
2087 	return vif->valid_links != 0;  in ieee80211_vif_is_mld()
2091  * ieee80211_vif_link_active - check if a given link is active
2102 	return vif->active_links & BIT(link_id);  in ieee80211_vif_link_active()
2106 	for (link_id = 0; link_id < ARRAY_SIZE((vif)->link_conf); link_id++)	\
2107 		if ((!(vif)->active_links ||					\
2108 		     (vif)->active_links & BIT(link_id)) &&			\
2114 	return vif->type == NL80211_IFTYPE_MESH_POINT;  in ieee80211_vif_is_mesh()
2120  * wdev_to_ieee80211_vif - return a vif struct from a wdev
2133  * ieee80211_vif_to_wdev - return a wdev struct from a vif
2146 	return lockdep_is_held(&ieee80211_vif_to_wdev(vif)->wiphy->mtx);  in lockdep_vif_wiphy_mutex_held()
2150 	rcu_dereference_protected((vif)->link_conf[link_id],	\
2154 	rcu_dereference_check((vif)->link_conf[link_id],	\
2158  * enum ieee80211_key_flags - key flags
2201  * @IEEE80211_KEY_FLAG_SPP_AMSDU: SPP A-MSDUs can be used with this key
2202  *	(set by mac80211 from the sta->spp_amsdu flag)
2220  * struct ieee80211_key_conf - key information
2229  * @tx_pn: PN used for TX keys, may be used by the driver as well if it
2230  *	needs to do software PN assignment by itself (e.g. due to TSO)
2232  * @keyidx: the key index (0-7)
2234  * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
2236  * 	- Temporal Encryption Key (128 bits)
2237  * 	- Temporal Authenticator Tx MIC Key (64 bits)
2238  * 	- Temporal Authenticator Rx MIC Key (64 bits)
2241  * @link_id: the link ID, 0 for non-MLO, or -1 for pairwise keys
2258 #define TKIP_PN_TO_IV16(pn) ((u16)(pn & 0xffff))  argument
2259 #define TKIP_PN_TO_IV32(pn) ((u32)((pn >> 16) & 0xffffffff))  argument
2262  * struct ieee80211_key_seq - key sequence counter
2265  * @ccmp: PN data, most significant byte first (big endian,
2267  * @aes_cmac: PN data, most significant byte first (big endian,
2269  * @aes_gmac: PN data, most significant byte first (big endian,
2271  * @gcmp: PN data, most significant byte first (big endian,
2273  * @hw: data for HW-only (e.g. cipher scheme) keys
2282 			u8 pn[6];  member
2285 			u8 pn[6];  member
2288 			u8 pn[6];  member
2291 			u8 pn[6];  member
2301  * enum set_key_cmd - key command
2314  * enum ieee80211_sta_state - station state
2333  * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
2355  * struct ieee80211_sta_rates - station rate selection table
2359  *	Overriding entries per-packet is possible by using cb tx control.
2373  * struct ieee80211_sta_txpwr - station txpower configuration
2391  * struct ieee80211_sta_aggregates - info that is aggregated from active links
2393  * Used for any per-link data that needs to be aggregated and updated in the
2396  * @max_amsdu_len: indicates the maximal length of an A-MSDU in bytes.
2401  *	  A-MSDU maximal size is min(max_amsdu_len, 4065) bytes.
2402  *	* If the skb is not part of a BA agreement, the A-MSDU maximal
2406  * driver. This is defined by the spec (IEEE 802.11-2012 section
2408  * @max_rc_amsdu_len: Maximum A-MSDU size in bytes recommended by rate control.
2409  * @max_tid_amsdu_len: Maximum A-MSDU size in bytes for this TID
2419  * struct ieee80211_link_sta - station Link specific info
2424  * @addr: MAC address of the Link STA. For non-MLO STA this is same as the addr
2436  * @agg: per-link data for multi-link aggregation
2468  * struct ieee80211_sta - station table entry
2471  * communicating with. Since stations are RCU-managed in
2499  *	A-MSDU. Taken from the Extended Capabilities element. 0 means
2506  * @txq: per-TID data TX queues; note that the last entry (%IEEE80211_NUM_TIDS)
2507  *	is used for non-data frames
2519  * @valid_links: bitmap of valid links, or 0 for non-MLO
2520  * @spp_amsdu: indicates whether the STA uses SPP A-MSDU or not.
2562 	rcu_dereference_protected((sta)->link[link_id],		\
2566 	rcu_dereference_check((sta)->link[link_id],		\
2570 	for (link_id = 0; link_id < ARRAY_SIZE((sta)->link); link_id++)		\
2571 		if ((!(vif)->active_links ||					\
2572 		     (vif)->active_links & BIT(link_id)) &&			\
2576  * enum sta_notify_cmd - sta notify command
2589  * struct ieee80211_tx_control - TX control data
2599  * struct ieee80211_txq - Software intermediate tx queue
2602  * @sta: station table entry, %NULL for per-vif queue
2603  * @tid: the TID for this queue (unused for per-vif queue),
2604  *	%IEEE80211_NUM_TIDS for non-data (if enabled)
2606  * @drv_priv: driver private area, sized by hw->txq_data_size
2622  * enum ieee80211_hw_flags - hardware flags
2670  *	Hardware supports 11n A-MPDU aggregation.
2691  *	periodic keep-alives to the AP and probing the AP on beacon loss.
2698  *	per-station GTKs as used by IBSS RSN or during fast transition. If
2699  *	the device doesn't support per-station GTKs, but can be asked not
2711  * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
2725  *	be created.  It is expected user-space will create vifs as
2729  *	crypto algorithms can be done in software - so don't automatically
2734  * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit,
2738  * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
2757  * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
2771  * @IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU: The driver supports receiving A-MSDUs
2772  *	within A-MPDU.
2788  *	which implies using per-CPU station statistics.
2791  *	A-MSDU frames. Requires software tx queueing and fast-xmit support.
2793  *	limit the maximum A-MSDU size based on the current tx rate by setting
2797  *	skbs, needed for zero-copy software A-MSDU.
2812  *	support QoS NDP for AP probing - that's most likely a driver bug.
2820  *	but if the rate control is built-in then it must be set by the driver.
2823  * @IEEE80211_HW_STA_MMPDU_TXQ: use the extra non-TID per-station TXQ for all
2827  * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU
2837  *	A-MPDU sessions active while rekeying with Extended Key ID.
2936  * struct ieee80211_hw - hardware information and state
2983  * @max_rates: maximum number of alternate rate retry stages the hw
2985  * @max_report_rates: maximum number of alternate rate retry stages
2990  *	sub-frames) to be used for A-MPDU block ack receiver
3003  * @max_tx_fragments: maximum number of tx buffers per (A)-MSDU, sum
3004  *	of 1 + skb_shinfo(skb)->nr_frags for each skb in the frag_list.
3019  *	@units_pos member is set to a non-negative value then the timestamp
3025  * @radiotap_timestamp.accuracy: If non-negative, fills the accuracy in the
3033  *	for each access category if it is uAPSD trigger-enabled and delivery-
3036  *	that corresponding AC is both trigger- and delivery-enabled. '0' means
3103 	return test_bit(flg, hw->flags);  in _ieee80211_hw_check()
3110 	return __set_bit(flg, hw->flags);  in _ieee80211_hw_set()
3115  * struct ieee80211_scan_request - hw scan request
3128  * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters
3130  * @sta: peer this TDLS channel-switch request/response came from
3131  * @chandef: channel referenced in a TDLS channel-switch request
3133  * @status: channel-switch response status
3135  * @switch_time: switch-timing parameter received in the frame
3136  * @switch_timeout: switch-timing parameter received in the frame
3137  * @tmpl_skb: TDLS switch-channel response template
3138  * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb
3153  * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
3159  * structure can then access it via hw->priv. Note that mac802111 drivers should
3168  * SET_IEEE80211_DEV - set device for 802.11 hardware
3175 	set_wiphy_dev(hw->wiphy, dev);  in SET_IEEE80211_DEV()
3179  * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
3186 	memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);  in SET_IEEE80211_PERM_ADDR()
3193 	if (WARN_ON_ONCE(c->control.rates[0].idx < 0))  in ieee80211_get_tx_rate()
3195 	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];  in ieee80211_get_tx_rate()
3202 	if (c->control.rts_cts_rate_idx < 0)  in ieee80211_get_rts_cts_rate()
3204 	return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];  in ieee80211_get_rts_cts_rate()
3211 	if (c->control.rates[idx + 1].idx < 0)  in ieee80211_get_alt_retry_rate()
3213 	return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];  in ieee80211_get_alt_retry_rate()
3217  * ieee80211_free_txskb - free TX skb
3227  * ieee80211_purge_tx_queue - purge TX skb queue
3258  * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
3294  * when they are able to replace in-use PTK keys according to the following
3299       at the time of the key deletion (including re-transmits),
3322  * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
3340  * hardware stays awake for a user-specified period of time after sending a
3357  * Driver informs U-APSD client support by enabling
3361  * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
3364  * Note: U-APSD client mode is not yet supported with
3395  *  - a list of information element IDs
3396  *  - a list of OUIs for the vendor information element
3410  * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
3434  * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
3498  * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
3502  * will not poll with PS-Poll and trigger with uAPSD at the same time.
3513  * handle PS-Poll/uAPSD.
3522  * cause mac80211 to retry the frame when the station wakes up. The
3527  * it can PS-Poll, or it can possibly start a uAPSD service period.
3530  * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
3535  * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
3541  * Additionally, non-bufferable MMPDUs can also be transmitted by
3549  * transmitted to a certain station is out-of-band communication to
3567  * there is more data on other TIDs -- the TIDs to release frames
3572  * shorten service periods (or abort PS-Poll responses), it must
3574  * are buffered in the driver -- those must remain buffered to avoid
3585  * Note that if the driver ever buffers frames other than QoS-data
3586  * frames, it must take care to never send a non-QoS-data frame as
3587  * the last frame in a service period, adding a QoS-nulldata frame
3588  * after a non-QoS-data frame if needed.
3595  * assignment of per-interface AC software queues to hardware queues. This
3597  * 1) off-channel transmissions might get stuck behind other frames
3599  * 3) after-DTIM frames could get stuck behind other frames
3623  * after-DTIM queue for AP:   8
3624  * off-channel queue:         9
3635  * and the second virtual interface with 4-7.
3647  * enum ieee80211_filter_flags - hardware filter flags
3694  * enum ieee80211_ampdu_mlme_action - A-MPDU actions
3739  * struct ieee80211_ampdu_params - AMPDU action parameters
3750  * @amsdu: indicates the peer's ability to receive A-MSDU within A-MPDU.
3766  * enum ieee80211_frame_release_type - frame release reason
3767  * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
3769  *	frame received on trigger-enabled AC
3777  * enum ieee80211_rate_control_changed - flags to indicate what changed
3781  *	information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
3798  * enum ieee80211_roc_type - remain on channel type
3816  * enum ieee80211_reconfig_type - reconfig type
3832  * struct ieee80211_prep_tx_info - prepare TX information
3833  * @duration: if non-zero, hint about the required duration,
3842  *	0 for a non-MLO connection.
3852  * struct ieee80211_ops - callbacks from mac80211 to the driver
3860  *	The low-level driver should send the frame out based on
3871  *	to avoid acknowledging frames before a non-monitor device
3955  *	non-MLO connections.
3996  *	offloading. The index can be 0-3, or -1 for unsetting it.
4005  *	at all but just send them after the SSID -- mac80211 includes the
4017  * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
4022  *	scan_work after the low-level driver was already suspended.
4044  * @get_stats: Return low-level statistics.
4049  *	IV/PN assignment then this callback should be provided to read the
4050  *	IV/PN for the given key from hardware.
4079  *	For non-MLO the callback will be called once for the default bss_conf
4091  *	For non-MLO the callback will be called once for the deflink with the
4108  *	isn't safe to use the pointer, not even RCU protected - no RCU grace
4133  *	let the driver pre-fill the statistics. The driver can fill most of
4135  *	all of them make sense - see the source for which ones are possible.
4141  *	accurate, so let the driver pre-fill the statistics. The driver can
4143  *	bitmap), but not all of them make sense - see the source for which
4178  *	Returns non-zero if this device sent the last beacon.
4181  * @get_survey: Return per-channel survey information
4184  *	need to set wiphy->rfkill_poll to %true before registration,
4189  *	in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
4190  *	accordingly; coverage class equals to -1 to enable ACK timeout
4217  *	reject TX/RX mask combinations they cannot support by returning -EINVAL
4222  * @remain_on_channel: Starts an off-channel period on the given channel, must
4225  *	offload. Frames to transmit on the off-channel channel are transmitted
4227  *	duration (which will always be non-zero) expires, the driver must call
4232  * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
4252  *	to release some frames, either for PS-poll or uAPSD.
4255  *	the frames being released then it must still set the more-data bit in
4257  *	more-data bit must always be set.
4259  *	from, for PS-poll it will always have only a single bit set.
4260  *	In the case this is used for a PS-poll initiated release, the
4263  *	on the TX status (and must report TX status) so that the PS-poll
4265  *	responses for a retried PS-poll frame.
4288  * @get_et_sset_count:  Ethtool API to get string-set count.
4295  *	and perhaps other supported types of ethtool data-sets.
4300  *	before associated. In multi-channel scenarios, a virtual interface is
4321  *	a TDLS discovery-request, we expect a reply to arrive on the AP's
4323  *	setup-response is a direct packet not buffered by the AP.
4325  *	discovery-request. The recommended period of protection is at least
4379  *	gets a CSA or a userspace initiated channel-switch), allowing
4402  * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
4403  *	is responsible for continually initiating channel-switching operations
4405  *	driver receives a channel-switch request template and the location of
4406  *	the switch-timing IE within the template as part of the invocation.
4408  *	optionally copy the skb for further re-use.
4409  * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
4411  * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or
4414  *	an ongoing channel-switch operation. In addition, a channel-switch
4416  *	switch-timing IE within the template. The skb can only be used within
4440  *	aggregating two specific frames in the same A-MSDU. The relation
4442  *	skb is always a real frame, head may or may not be an A-MSDU.
4454  *	4-address mode
4480  *	new links bitmaps may be 0 if going from/to a non-MLO situation.
4489  *	i.e. passed to @sta_add/@sta_state with sta->valid_links not zero.
4499  *	if the requested TID-To-Link mapping can be accepted or not.
4501  *	modify @ttlm parameter with the suggested TID-to-Link mapping.
4640 		       const struct ieee80211_tx_queue_params *params);
4655 	 * Perform a certain A-MPDU action.
4665 	 * - ``TX: 1.....7``
4666 	 * - ``RX:  2....7`` (lost frame #1)
4667 	 * - ``TX:        8..1...``
4669 	 * which is invalid since #1 was now re-transmitted well past the
4672 	 * - ``TX:        1   or``
4673 	 * - ``TX:        18  or``
4674 	 * - ``TX:        81``
4686 			    struct ieee80211_ampdu_params *params);
4821 					 struct ieee80211_tdls_ch_sw_params *params);
4906  * ieee80211_alloc_hw_nm - Allocate a new hardware device
4926  * ieee80211_alloc_hw - Allocate a new hardware device
4947  * ieee80211_register_hw - Register hardware device
4960  * struct ieee80211_tpt_blink - throughput blink description
4971  * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
4995  * ieee80211_get_tx_led_name - get name of TX LED
5016  * ieee80211_get_rx_led_name - get name of RX LED
5037  * ieee80211_get_assoc_led_name - get name of association LED
5058  * ieee80211_get_radio_led_name - get name of radio LED
5079  * ieee80211_create_tpt_led_trigger - create throughput LED trigger
5082  * @blink_table: the blink table -- needs to be ordered by throughput
5104  * ieee80211_unregister_hw - Unregister a hardware device
5114  * ieee80211_free_hw - free hardware descriptor
5125  * ieee80211_restart_hw - restart hardware completely
5131  * calling the ->start() operation. The driver will need to reset all
5139  * ieee80211_rx_list - receive frame and store processed skbs in a list
5164  * ieee80211_rx_napi - receive frame from NAPI context
5189  * ieee80211_rx - receive frame
5214  * ieee80211_rx_irqsafe - receive frame
5229  * ieee80211_rx_ni - receive frame (in process context)
5250  * ieee80211_sta_ps_transition - PS transition for connected sta
5264  * Return: 0 on success. -EINVAL when the requested PS mode is already set.
5269  * ieee80211_sta_ps_transition_ni - PS transition for connected sta
5294  * ieee80211_sta_pspoll - PS-Poll frame received
5298  * use this function to inform mac80211 that a PS-Poll frame from a
5307  * ieee80211_sta_uapsd_trigger - (potential) U-APSD trigger frame received
5331  * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
5345  * If all frames are released to the station (due to PS-poll or uAPSD)
5362  * ieee80211_get_tx_rates - get the selected transmit rates for a packet
5364  * Call this function in a driver with per-packet rate selection support
5371  * @dest: buffer for extracted rate/retry information
5381  * ieee80211_tx_rate_update - transmit rate update callback
5383  * Drivers should call this functions with a non-NULL pub sta
5396  * ieee80211_tx_status_skb - transmit status callback
5415  * ieee80211_tx_status_ext - extended transmit status callback
5432  * ieee80211_tx_status_noskb - transmit status callback without skb
5460  * ieee80211_tx_status_ni - transmit status callback (in process context)
5480  * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
5495  * ieee80211_report_low_ack - report non-responding station
5497  * When operating in AP-mode, call this function to report a non-responding
5500  * @sta: the non-responding connected sta
5508  * struct ieee80211_mutable_offsets - mutable beacon offsets
5525  * ieee80211_beacon_get_template - beacon template generation function
5552  * ieee80211_beacon_get_template_ema_index - EMA beacon template generation
5557  * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP).
5573  * struct ieee80211_ema_beacons - List of EMA beacons
5590  * ieee80211_beacon_get_template_ema_list - EMA beacon template generation
5593  * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP)
5611  * ieee80211_beacon_free_ema_list - free an EMA beacon template list
5620  * ieee80211_beacon_get_tim - beacon generation function
5624  *	Set to 0 if invalid (in non-AP modes).
5627  *	Set to 0 if invalid (in non-AP modes).
5636  * frame from mac80211 -- it is responsible for calling this function exactly
5649  * ieee80211_beacon_get - beacon generation function
5667  * ieee80211_beacon_update_cntdwn - request mac80211 to decrement the beacon countdown
5669  * @link_id: valid link_id during MLO or 0 for non-MLO
5683  * ieee80211_beacon_set_cntdwn - request mac80211 to set beacon countdown
5696  * ieee80211_csa_finish - notify mac80211 about channel switch
5698  * @link_id: valid link_id during MLO or 0 for non-MLO
5707  * ieee80211_beacon_cntdwn_is_complete - find out if countdown reached 1
5709  * @link_id: valid link_id during MLO or 0 for non-MLO
5717  * ieee80211_color_change_finish - notify mac80211 about color change
5719  * @link_id: valid link_id during MLO or 0 for non-MLO
5728  * ieee80211_proberesp_get - retrieve a Probe Response template
5743  * ieee80211_pspoll_get - retrieve a PS Poll template
5760  * ieee80211_nullfunc_get - retrieve a nullfunc template
5786  * ieee80211_probereq_get - retrieve a Probe Request template
5804  * ieee80211_rts_get - RTS frame generation function
5813  * hardware/firmware), the low-level driver uses this function to receive
5814  * the next RTS frame from the 802.11 code. The low-level is responsible
5823  * ieee80211_rts_duration - Get the duration field for an RTS frame
5830  * the duration field, the low-level driver uses this function to receive
5831  * the duration field value in little-endian byteorder.
5840  * ieee80211_ctstoself_get - CTS-to-self frame generation function
5843  * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
5846  * @cts: The buffer where to store the CTS-to-self frame.
5848  * If the CTS-to-self frames are generated by the host system (i.e., not in
5849  * hardware/firmware), the low-level driver uses this function to receive
5850  * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
5851  * for calling this function before and CTS-to-self frame is needed.
5860  * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
5863  * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
5866  * If the CTS-to-self is generated in firmware, but the host system must provide
5867  * the duration field, the low-level driver uses this function to receive
5868  * the duration field value in little-endian byteorder.
5878  * ieee80211_generic_frame_duration - Calculate the duration field for a frame
5897  * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
5904  * memory. The low-level driver uses this function to fetch next buffered
5911  * generated with ieee80211_beacon_get() and the low-level driver must thus
5913  * NULL if the previous generated beacon was not DTIM, so the low-level driver
5921  * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
5933  * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
5946 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;  in ieee80211_get_tkip_p1k()
5947 	const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);  in ieee80211_get_tkip_p1k()
5954  * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
5968  * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
5982  * ieee80211_tkip_add_iv - write TKIP IV and Ext. IV to pos
5986  * @pn: PN to add
5994 u8 *ieee80211_tkip_add_iv(u8 *pos, struct ieee80211_key_conf *keyconf, u64 pn);
5997  * ieee80211_get_key_rx_seq - get key RX sequence counter
6000  * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
6001  *	the value on TID 0 is also used for non-QoS frames. For
6016  * ieee80211_set_key_rx_seq - set key RX sequence counter
6019  * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
6020  *	the value on TID 0 is also used for non-QoS frames. For
6036  * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
6042  * @link_id: the link id of the key or -1 for non-MLO
6050  * mac80211-owned memory. In case of errors, the function returns an
6072  * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
6082  * ieee80211_key_mic_failure - increment MIC failure counter for the key
6092  * ieee80211_key_replay - increment replay counter for the key
6102  * ieee80211_wake_queue - wake specific queue
6111  * ieee80211_stop_queue - stop specific queue
6120  * ieee80211_queue_stopped - test status of the queue
6132  * ieee80211_stop_queues - stop all queues
6140  * ieee80211_wake_queues - wake all queues
6148  * ieee80211_scan_completed - completed hardware scan
6162  * ieee80211_sched_scan_results - got results from scheduled scan
6172  * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
6184  * enum ieee80211_interface_iteration_flags - interface iteration flags
6189  *	haven't been re-added to the driver yet.
6191  *	interfaces, even if they haven't been re-added to the driver yet.
6205  * ieee80211_iterate_interfaces - iterate interfaces
6223  * ieee80211_iterate_active_interfaces - iterate active interfaces
6249  * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
6270  * ieee80211_iterate_active_interfaces_mtx - iterate active interfaces
6289  * ieee80211_iterate_stations_atomic - iterate stations
6306  * ieee80211_iterate_stations_mtx - iterate stations
6323  * ieee80211_queue_work - add work onto the mac80211 workqueue
6334  * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
6348  * ieee80211_refresh_tx_agg_session_timer - Refresh a tx agg session timer.
6362  * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
6377  * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
6390  * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
6403  * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
6416  * ieee80211_find_sta - find a station
6430  * ieee80211_find_sta_by_ifaddr - find a station on hardware
6434  * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
6456  * ieee80211_find_sta_by_link_addrs - find STA by link addresses
6474  * ieee80211_sta_block_awake - block station from waking up
6485  * This function allows implementing this mode in a race-free
6495  * cause mac80211 to be able to send ps-poll responses, and if
6506  * ieee80211_sta_eosp - notify mac80211 about end of SP
6512  * This applies for PS-Poll as well as uAPSD.
6515  * not mix calls to irqsafe/non-irqsafe versions, this function
6517  * all non-irqsafe, don't mix!
6527  * ieee80211_send_eosp_nullfunc - ask mac80211 to send NDP with EOSP
6540  * will be sent despite the station being in power-save.
6549  * ieee80211_sta_recalc_aggregates - recalculate aggregate data after a change
6552  * Call this function after changing a per-link aggregate data as referenced in
6562  * ieee80211_sta_register_airtime - register airtime usage for a sta/tid
6590  * ieee80211_txq_airtime_check - check if a txq can send frame to device
6602  * ieee80211_iter_keys - iterate keys programmed into the device
6629  * ieee80211_iter_keys_rcu - iterate keys programmed into the device
6653  * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
6668  * found while iterating, whether they've been re-added already
6679  * ieee80211_iter_chan_contexts_mtx - iterate channel contexts
6693  * found while iterating, whether they've been re-added already
6704  * ieee80211_ap_probereq_get - retrieve a Probe Request template
6721  * ieee80211_beacon_loss - inform hardware does not receive beacons
6732  * ieee80211_connection_loss - inform hardware has lost connection to the AP
6748  * ieee80211_disconnect - request disconnection
6759  * ieee80211_resume_disconnect - disconnect from AP after resume
6782  * ieee80211_hw_restart_disconnect - disconnect from AP after
6792  * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
6810  * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss
6818  * ieee80211_radar_detected - inform that a radar was detected
6822  *	pass a valid pointer during MLO. For non-MLO %NULL can be passed
6828  * ieee80211_chswitch_done - Complete channel switch process
6834  * Complete the channel switch post-process: set the new operational channel
6841  * ieee80211_channel_switch_disconnect - disconnect due to channel switch error
6851  * ieee80211_request_smps - request SM PS transition
6864  * ieee80211_ready_on_channel - notification of remain-on-channel start
6870  * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
6876  * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
6883  * therefore prevent the peer device to use a-mpdu aggregation.
6893  * ieee80211_mark_rx_ba_filtered_frames - move RX BA window and mark filtered
6912  * ieee80211_send_bar - send a BlockAckReq frame
6925  * ieee80211_manage_rx_ba_offl - helper to queue an RX BA work
6934  * ieee80211_start_rx_ba_session_offl - start a Rx BA session
6956  * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session
6978  * ieee80211_rx_ba_timer_expired - stop a Rx BA session due to timeout
6995  * struct ieee80211_tx_rate_control - rate control information for/from RC algo
7007  * @short_preamble: whether mac80211 will request short-preamble transmission
7009  * @rate_idx_mask: user-requested (legacy) rate mask
7010  * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
7026  * enum rate_control_capabilities - rate control capabilities
7039 	 * mac80211 should start A-MPDU sessions on tx
7082 	return (sta == NULL || sta->deflink.supp_rates[band] & BIT(index));  in rate_supported()
7091 	for (i = 0; i < sband->n_bitrates; i++)  in rate_lowest_index()
7092 		if (rate_supported(sta, sband->band, i))  in rate_lowest_index()
7108 	for (i = 0; i < sband->n_bitrates; i++)  in rate_usable_index_exists()
7109 		if (rate_supported(sta, sband->band, i))  in rate_usable_index_exists()
7115  * rate_control_set_rates - pass the sta rate selection to mac80211/driver
7138 	return conf->chandef.width == NL80211_CHAN_WIDTH_20;  in conf_is_ht20()
7144 	return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&  in conf_is_ht40_minus()
7145 	       conf->chandef.center_freq1 < conf->chandef.chan->center_freq;  in conf_is_ht40_minus()
7151 	return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&  in conf_is_ht40_plus()
7152 	       conf->chandef.center_freq1 > conf->chandef.chan->center_freq;  in conf_is_ht40_plus()
7158 	return conf->chandef.width == NL80211_CHAN_WIDTH_40;  in conf_is_ht40()
7164 	return (conf->chandef.width != NL80211_CHAN_WIDTH_5) &&  in conf_is_ht()
7165 		(conf->chandef.width != NL80211_CHAN_WIDTH_10) &&  in conf_is_ht()
7166 		(conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT);  in conf_is_ht()
7188 	return ieee80211_iftype_p2p(vif->type, vif->p2p);  in ieee80211_vif_type_p2p()
7192  * ieee80211_get_he_iftype_cap_vif - return HE capabilities for sband/vif
7206  * ieee80211_get_he_6ghz_capa_vif - return HE 6 GHz capabilities
7220  * ieee80211_get_eht_iftype_cap_vif - return ETH capabilities for sband/vif
7234  * ieee80211_update_mu_groups - set the VHT MU-MIMO groud data
7238  * @membership: 64 bits array - a bit is set if station is member of the group
7256  * ieee80211_ave_rssi - report the average RSSI for the specified interface
7259  * @link_id: the link ID for MLO, or -1 for non-MLO
7269  * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
7281  * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
7297  * ieee80211_parse_tx_radiotap - Sanity-check and parse the radiotap header
7313  * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
7340  * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
7352  * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
7360  * ieee80211_tdls_oper_request - request userspace to perform a TDLS operation
7374  * ieee80211_reserve_tid - request to reserve a specific TID
7395  * ieee80211_unreserve_tid - request to unreserve a specific TID
7411  * ieee80211_tx_dequeue - dequeue a packet from a software tx queue
7421  * skb->cb, e.g. the key pointer, are protected by RCU and thus the
7434  * ieee80211_tx_dequeue_ni - dequeue a packet from a software tx queue
7459  * ieee80211_handle_wake_tx_queue - mac80211 handler for wake_tx_queue callback
7471  * ieee80211_next_txq - get next tx queue to pull packets from
7483  * ieee80211_txq_schedule_start - start new scheduling round for TXQs
7502  * ieee80211_schedule_txq - schedule a TXQ for transmission
7520  * ieee80211_return_txq - return a TXQ previously acquired by ieee80211_next_txq()
7537  * ieee80211_txq_may_transmit - check whether TXQ is allowed to transmit
7551  * aligned against driver's own round-robin scheduler list. i.e it rotates
7566  * ieee80211_txq_get_depth - get pending frame/byte count of given txq
7569  * txq state can change half-way of this function and the caller may end up
7570  * with "new" frame_cnt and "old" byte_cnt or vice-versa.
7581  * ieee80211_nan_func_terminated - notify about NAN function termination.
7597  * ieee80211_nan_func_match - notify about NAN function match event.
7612  * ieee80211_calc_rx_airtime - calculate estimated transmission airtime for RX.
7629  * ieee80211_calc_tx_airtime - calculate estimated transmission airtime for TX.
7644  * ieee80211_get_fils_discovery_tmpl - Get FILS discovery template.
7656  * ieee80211_get_unsol_bcast_probe_resp_tmpl - Get unsolicited broadcast
7670  * ieee80211_obss_color_collision_notify - notify userland about a BSS color
7672  * @link_id: valid link_id during MLO or 0 for non-MLO
7683  * ieee80211_is_tx_data - check if frame is a data frame
7695 	struct ieee80211_hdr *hdr = (void *) skb->data;  in ieee80211_is_tx_data()
7697 	return info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP ||  in ieee80211_is_tx_data()
7698 	       ieee80211_is_data(hdr->frame_control);  in ieee80211_is_tx_data()
7702  * ieee80211_set_active_links - set active links in client mode
7717  *  - change_vif_links(0x11)
7718  *  - unassign_vif_chanctx(link_id=0)
7719  *  - assign_vif_chanctx(link_id=4)
7720  *  - change_sta_links(0x11) for each affected STA (the AP)
7722  *  - remove group keys on the old link (link_id 0)
7723  *  - add new group keys (GTK/IGTK/BIGTK) on the new link (link_id 4)
7724  *  - change_sta_links(0x10) for each affected STA (the AP)
7725  *  - change_vif_links(0x10)
7732  * ieee80211_set_active_links_async - asynchronously set active links
7745  * ieee80211_send_teardown_neg_ttlm - tear down a negotiated TTLM request
7754  * ieee80211_chan_width_to_rx_bw - convert channel width to STA RX bandwidth
7781  * ieee80211_prepare_rx_omi_bw - prepare for sending BW RX OMI
7816  * ieee80211_finalize_rx_omi_bw - finalize BW RX OMI update
7824 /* for older drivers - let's not document these ... */