Lines Matching refs:rsi_dbg
180 rsi_dbg(ERR_ZONE, "%s: Reset failed : %d\n", __func__, ret); in rsi_reset_card()
224 rsi_dbg(ERR_ZONE, "%s: CMD0 failed : %d\n", __func__, err); in rsi_reset_card()
230 rsi_dbg(ERR_ZONE, "%s: CMD5 failed : %d\n", in rsi_reset_card()
239 rsi_dbg(ERR_ZONE, "%s: CMD5 failed : %d\n", in rsi_reset_card()
250 rsi_dbg(ERR_ZONE, "%s: card in not ready : %d %d\n", in rsi_reset_card()
262 rsi_dbg(ERR_ZONE, "%s: CMD3 failed : %d\n", __func__, err); in rsi_reset_card()
276 rsi_dbg(ERR_ZONE, "%s: CMD7 failed : %d\n", __func__, err); in rsi_reset_card()
282 rsi_dbg(ERR_ZONE, "%s: Set high speed mode\n", __func__); in rsi_reset_card()
285 rsi_dbg(ERR_ZONE, "%s: CCCR speed reg read failed: %d\n", in rsi_reset_card()
292 rsi_dbg(ERR_ZONE, in rsi_reset_card()
321 rsi_dbg(ERR_ZONE, "%s: Set bus mode failed : %d\n", in rsi_reset_card()
361 rsi_dbg(INIT_ZONE, "%s: Setting the block length\n", __func__); in rsi_setblocklength()
367 rsi_dbg(INFO_ZONE, in rsi_setblocklength()
388 rsi_dbg(ERR_ZONE, in rsi_setupcard()
472 rsi_dbg(ERR_ZONE, "%s: unable to send ack\n", __func__); in rsi_sdio_ack_intr()
504 rsi_dbg(ERR_ZONE, "%s: Synch Cmd53 read failed\n", __func__); in rsi_sdio_read_register_multiple()
527 rsi_dbg(ERR_ZONE, "%s: Stopping card writes\n", __func__); in rsi_sdio_write_register_multiple()
534 rsi_dbg(ERR_ZONE, "%s: Continue card writes\n", __func__); in rsi_sdio_write_register_multiple()
547 rsi_dbg(ERR_ZONE, "%s: Synch Cmd53 write failed %d\n", in rsi_sdio_write_register_multiple()
570 rsi_dbg(INFO_ZONE, "ins_size: %d, num_blocks: %d\n", in rsi_sdio_load_data_master_write()
580 rsi_dbg(ERR_ZONE, "%s: Unable to set ms word reg\n", __func__); in rsi_sdio_load_data_master_write()
592 rsi_dbg(ERR_ZONE, "%s: failed to write\n", __func__); in rsi_sdio_load_data_master_write()
595 rsi_dbg(INFO_ZONE, "%s: loading block: %d\n", __func__, i); in rsi_sdio_load_data_master_write()
605 rsi_dbg(ERR_ZONE, in rsi_sdio_load_data_master_write()
625 rsi_dbg(INFO_ZONE, in rsi_sdio_load_data_master_write()
651 rsi_dbg(ERR_ZONE, in rsi_sdio_master_reg_read()
671 rsi_dbg(ERR_ZONE, "%s: AHB register read failed\n", __func__); in rsi_sdio_master_reg_read()
724 rsi_dbg(ERR_ZONE, in rsi_sdio_master_reg_write()
738 rsi_dbg(ERR_ZONE, in rsi_sdio_master_reg_write()
780 rsi_dbg(ERR_ZONE, "%s: Unable to write onto the card: %d\n", in rsi_sdio_host_intf_write_pkt()
782 rsi_dbg(DATA_TX_ZONE, "%s: Successfully written onto card\n", __func__); in rsi_sdio_host_intf_write_pkt()
802 rsi_dbg(ERR_ZONE, "%s: Pkt size is zero\n", __func__); in rsi_sdio_host_intf_read_pkt()
812 rsi_dbg(ERR_ZONE, "%s: Failed to read frame: %d\n", __func__, in rsi_sdio_host_intf_read_pkt()
842 rsi_dbg(ERR_ZONE, "%s: Failed to enable interface\n", __func__); in rsi_init_sdio_interface()
847 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); in rsi_init_sdio_interface()
856 rsi_dbg(ERR_ZONE, "%s: Failed to setup card\n", __func__); in rsi_init_sdio_interface()
860 rsi_dbg(INIT_ZONE, "%s: Setup card successfully\n", __func__); in rsi_init_sdio_interface()
864 rsi_dbg(ERR_ZONE, "%s: Failed to init slave regs\n", __func__); in rsi_init_sdio_interface()
920 rsi_dbg(ERR_ZONE, in rsi_sdio_ta_reset()
925 rsi_dbg(INIT_ZONE, "%s: Bring TA out of reset\n", __func__); in rsi_sdio_ta_reset()
932 rsi_dbg(ERR_ZONE, "Unable to hold TA threads\n"); in rsi_sdio_ta_reset()
942 rsi_dbg(ERR_ZONE, "Unable to get TA out of reset\n"); in rsi_sdio_ta_reset()
952 rsi_dbg(ERR_ZONE, "Unable to Reset TA PC value\n"); in rsi_sdio_ta_reset()
963 rsi_dbg(ERR_ZONE, "Unable to release TA threads\n"); in rsi_sdio_ta_reset()
969 rsi_dbg(ERR_ZONE, "Unable to set ms word to common reg\n"); in rsi_sdio_ta_reset()
972 rsi_dbg(INIT_ZONE, "***** TA Reset done *****\n"); in rsi_sdio_ta_reset()
1008 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); in rsi_probe()
1012 rsi_dbg(ERR_ZONE, "%s: Failed to init os intf ops\n", in rsi_probe()
1020 rsi_dbg(ERR_ZONE, "%s: Failed to init sdio interface\n", in rsi_probe()
1027 rsi_dbg(ERR_ZONE, "%s: 9113 module detected\n", __func__); in rsi_probe()
1030 rsi_dbg(ERR_ZONE, "%s: 9116 module detected\n", __func__); in rsi_probe()
1033 rsi_dbg(ERR_ZONE, in rsi_probe()
1044 rsi_dbg(ERR_ZONE, "%s: Unable to init rx thrd\n", __func__); in rsi_probe()
1050 rsi_dbg(ERR_ZONE, "%s: Failed to request IRQ\n", __func__); in rsi_probe()
1056 rsi_dbg(INIT_ZONE, "%s: Registered Interrupt handler\n", __func__); in rsi_probe()
1059 rsi_dbg(ERR_ZONE, "%s: Failed in device init\n", __func__); in rsi_probe()
1063 rsi_dbg(INFO_ZONE, "===> RSI Device Init Done <===\n"); in rsi_probe()
1066 rsi_dbg(ERR_ZONE, "%s: Unable to set ms word reg\n", __func__); in rsi_probe()
1087 rsi_dbg(ERR_ZONE, "%s: Failed in probe...Exiting\n", __func__); in rsi_probe()
1117 rsi_dbg(INFO_ZONE, "Writing disable to wakeup register\n"); in rsi_reset_chip()
1120 rsi_dbg(ERR_ZONE, in rsi_reset_chip()
1128 rsi_dbg(ERR_ZONE, "%s: Failed to Read Intr Status Register\n", in rsi_reset_chip()
1132 rsi_dbg(INFO_ZONE, "%s: Intr Status Register value = %d\n", in rsi_reset_chip()
1137 rsi_dbg(ERR_ZONE, in rsi_reset_chip()
1147 rsi_dbg(ERR_ZONE, in rsi_reset_chip()
1174 rsi_dbg(ERR_ZONE, "Failed to write to intr timer\n"); in rsi_reset_chip()
1180 rsi_dbg(ERR_ZONE, in rsi_reset_chip()
1187 rsi_dbg(ERR_ZONE, in rsi_reset_chip()
1190 rsi_dbg(ERR_ZONE, "***** Watch Dog Reset Successful *****\n"); in rsi_reset_chip()
1242 rsi_dbg(ERR_ZONE, "##### RSI SDIO device disconnected #####\n"); in rsi_disconnect()
1255 rsi_dbg(ERR_ZONE, "Set sdio keep pwr flag failed: %d\n", ret); in rsi_set_sdio_pm_caps()
1267 rsi_dbg(INFO_ZONE, "Waiting for interrupts to be cleared.."); in rsi_sdio_disable_interrupts()
1272 rsi_dbg(INFO_ZONE, "."); in rsi_sdio_disable_interrupts()
1274 rsi_dbg(INFO_ZONE, "Interrupts cleared\n"); in rsi_sdio_disable_interrupts()
1279 rsi_dbg(ERR_ZONE, in rsi_sdio_disable_interrupts()
1288 rsi_dbg(ERR_ZONE, in rsi_sdio_disable_interrupts()
1295 rsi_dbg(ERR_ZONE, in rsi_sdio_disable_interrupts()
1300 rsi_dbg(INFO_ZONE, "int enable reg content = %x\n", data); in rsi_sdio_disable_interrupts()
1317 rsi_dbg(ERR_ZONE, in rsi_sdio_enable_interrupts()
1326 rsi_dbg(ERR_ZONE, in rsi_sdio_enable_interrupts()
1334 rsi_dbg(ERR_ZONE, in rsi_sdio_enable_interrupts()
1339 rsi_dbg(ERR_ZONE, in rsi_sdio_enable_interrupts()
1343 rsi_dbg(INFO_ZONE, "int enable reg content = %x\n", data); in rsi_sdio_enable_interrupts()
1358 rsi_dbg(ERR_ZONE, "Device is not ready\n"); in rsi_suspend()
1366 rsi_dbg(INFO_ZONE, in rsi_suspend()
1393 rsi_dbg(INFO_ZONE, "SDIO Bus freeze ===>\n"); in rsi_freeze()
1396 rsi_dbg(ERR_ZONE, "Device is not ready\n"); in rsi_freeze()
1404 rsi_dbg(ERR_ZONE, in rsi_freeze()
1416 rsi_dbg(INFO_ZONE, "###### Device is not ready #######\n"); in rsi_freeze()
1420 rsi_dbg(INFO_ZONE, "Setting power management caps failed\n"); in rsi_freeze()
1422 rsi_dbg(INFO_ZONE, "***** RSI module freezed *****\n"); in rsi_freeze()
1433 rsi_dbg(ERR_ZONE, "SDIO Bus thaw =====>\n"); in rsi_thaw()
1441 rsi_dbg(INFO_ZONE, "***** RSI module thaw done *****\n"); in rsi_thaw()
1453 rsi_dbg(ERR_ZONE, "SDIO Bus shutdown =====>\n"); in rsi_shutdown()
1457 rsi_dbg(ERR_ZONE, "Failed to configure WoWLAN\n"); in rsi_shutdown()
1469 rsi_dbg(INFO_ZONE, "###### Device is not ready #######\n"); in rsi_shutdown()
1471 rsi_dbg(INFO_ZONE, "***** RSI module shut down *****\n"); in rsi_shutdown()
1480 rsi_dbg(INFO_ZONE, "SDIO Bus restore ======>\n"); in rsi_restore()
1491 rsi_dbg(INFO_ZONE, "RSI module restored\n"); in rsi_restore()