1 // SPDX-License-Identifier: GPL-2.0+
188 /* RGMII to 1000BASE-X */
190 /* RGMII to 100BASE-FX */
390 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {  in marvell_config_intr()
454 	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);  in marvell_config_aneg()
469 	if (phydev->autoneg != AUTONEG_ENABLE || changed) {  in marvell_config_aneg()
519  * marvell,reg-init property stored in the of_node for the phydev.
521  * marvell,reg-init = <reg-page reg mask value>,...;
523  * There may be one or more sets of <reg-page reg mask value>:
525  * reg-page: which register bank to use.
527  * mask: if non-zero, ANDed with existing register value.
536 	if (!phydev->mdio.dev.of_node)  in marvell_of_reg_init()
539 	paddr = of_get_property(phydev->mdio.dev.of_node,  in marvell_of_reg_init()
540 				"marvell,reg-init", &len);  in marvell_of_reg_init()
550 	for (i = 0; i < len - 3; i += 4) {  in marvell_of_reg_init()
593 	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)  in m88e1121_config_aneg_rgmii_delays()
596 	else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)  in m88e1121_config_aneg_rgmii_delays()
598 	else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)  in m88e1121_config_aneg_rgmii_delays()
621 	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);  in m88e1121_config_aneg()
631 	if (phydev->autoneg != AUTONEG_ENABLE || changed) {  in m88e1121_config_aneg()
662  * register for fiber link.
683  * marvell_config_aneg_fiber - restart auto-negotiation or write BMCR
686  * Description: If auto-negotiation is enabled, we configure the
687  *   advertising, and then restart auto-negotiation.  If it is not
688  *   enabled, then we write the BMCR. Adapted for fiber link in
697 	if (phydev->autoneg != AUTONEG_ENABLE)  in marvell_config_aneg_fiber()
701 	linkmode_and(phydev->advertising, phydev->advertising,  in marvell_config_aneg_fiber()
702 		     phydev->supported);  in marvell_config_aneg_fiber()
704 	adv = linkmode_adv_to_fiber_adv_t(phydev->advertising);  in marvell_config_aneg_fiber()
706 	/* Setup fiber advertisement */  in marvell_config_aneg_fiber()
730 	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&  in m88e1111_config_aneg()
744 	/* Then the fiber link */  in m88e1111_config_aneg()
749 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII)  in m88e1111_config_aneg()
750 		/* Do not touch the fiber advertisement if we're in copper->sgmii mode.  in m88e1111_config_aneg()
751 		 * Just ensure that SGMII-side autonegotiation is enabled.  in m88e1111_config_aneg()
752 		 * If we switched from some other mode to SGMII it may not be.  in m88e1111_config_aneg()
780 	/* Do not touch the fiber page if we're in copper->sgmii mode */  in m88e1510_config_aneg()
781 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII)  in m88e1510_config_aneg()
784 	/* Then the fiber link */  in m88e1510_config_aneg()
805 	switch (MARVELL_PHY_FAMILY_ID(phydev->phy_id)) {  in marvell_config_led()
817 		if (phydev->dev_flags & MARVELL_PHY_LED0_LINK_LED1_ACTIVE)  in marvell_config_led()
837 	/* Set registers from marvell,reg-init DT property */  in marvell_config_init()
845 	/* Enable Scrambler and Auto-Crossover */  in m88e3016_config_init()
856 					   u16 mode,  in m88e1111_config_init_hwcfg_mode()  argument
860 		mode |= MII_M1111_HWCFG_FIBER_COPPER_AUTO;  in m88e1111_config_init_hwcfg_mode()
866 			  mode);  in m88e1111_config_init_hwcfg_mode()
873 	switch (phydev->interface) {  in m88e1111_config_init_rgmii_delays()
960 	int err, mode;  in m88e1111_config_init_1000basex()  local
965 	/* If using copper mode, ensure 1000BaseX auto-negotiation is enabled.  in m88e1111_config_init_1000basex()
966 	 * FIXME: this does not actually enable 1000BaseX auto-negotiation if  in m88e1111_config_init_1000basex()
967 	 * it was previously disabled in the Fiber BMCR!  in m88e1111_config_init_1000basex()
969 	mode = extsr & MII_M1111_HWCFG_MODE_MASK;  in m88e1111_config_init_1000basex()
970 	if (mode == MII_M1111_HWCFG_MODE_COPPER_1000X_NOAN) {  in m88e1111_config_init_1000basex()
992 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {  in m88e1111_config_init()
998 	if (phydev->interface == PHY_INTERFACE_MODE_RTBI) {  in m88e1111_config_init()
1004 	if (phydev->interface == PHY_INTERFACE_MODE_1000BASEX) {  in m88e1111_config_init()
1018 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {  in m88e1111_config_init()
1019 		/* If the HWCFG_MODE was changed from another mode (such as  in m88e1111_config_init()
1025 		linkmode_or(phydev->advertising, phydev->advertising,  in m88e1111_config_init()
1026 			    phydev->supported);  in m88e1111_config_init()
1052 		return -E2BIG;  in m88e1111_set_downshift()
1059 		val |= FIELD_PREP(MII_M1111_PHY_EXT_CR_DOWNSHIFT_MASK, cnt - 1);  in m88e1111_set_downshift()
1076 	switch (tuna->id) {  in m88e1111_get_tunable()
1080 		return -EOPNOTSUPP;  in m88e1111_get_tunable()
1087 	switch (tuna->id) {  in m88e1111_set_tunable()
1091 		return -EOPNOTSUPP;  in m88e1111_set_tunable()
1116 		return -E2BIG;  in m88e1011_set_downshift()
1123 		val |= FIELD_PREP(MII_M1011_PHY_SCR_DOWNSHIFT_MASK, cnt - 1);  in m88e1011_set_downshift()
1140 	switch (tuna->id) {  in m88e1011_get_tunable()
1144 		return -EOPNOTSUPP;  in m88e1011_get_tunable()
1151 	switch (tuna->id) {  in m88e1011_set_tunable()
1155 		return -EOPNOTSUPP;  in m88e1011_set_tunable()
1205 	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);  in m88e1116r_config_init()
1255 	/* As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/  in m88e1510_config_init()
1283 	/* SGMII-to-Copper mode initialization */  in m88e1510_config_init()
1284 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {  in m88e1510_config_init()
1290 		/* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */  in m88e1510_config_init()
1297 		/* PHY reset is necessary after changing MODE[2:0] */  in m88e1510_config_init()
1319 	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);  in m88e1118_config_aneg()
1348 	if (phydev->dev_flags & MARVELL_PHY_M1118_DNS323_LEDS)  in m88e1118_config_init()
1403 	if (phydev->dev_flags & MARVELL_PHY_M1145_FLAGS_RESISTANCE) {  in m88e1145_config_init_rgmii()
1451 	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {  in m88e1145_config_init()
1457 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {  in m88e1145_config_init()
1502 		return -EINVAL;  in m88e1540_get_fld()
1523 		return -EBUSY;  in m88e1540_set_fld()
1549 	switch (tuna->id) {  in m88e1540_get_tunable()
1555 		return -EOPNOTSUPP;  in m88e1540_get_tunable()
1562 	switch (tuna->id) {  in m88e1540_set_tunable()
1568 		return -EOPNOTSUPP;  in m88e1540_set_tunable()
1608  * @lpa: value of the MII_LPA register for fiber link
1624 				       int fiber, int status)  in marvell_read_status_page_an()  argument
1630 		phydev->link = 0;  in marvell_read_status_page_an()
1635 		phydev->duplex = DUPLEX_FULL;  in marvell_read_status_page_an()
1637 		phydev->duplex = DUPLEX_HALF;  in marvell_read_status_page_an()
1641 		phydev->speed = SPEED_1000;  in marvell_read_status_page_an()
1645 		phydev->speed = SPEED_100;  in marvell_read_status_page_an()
1649 		phydev->speed = SPEED_10;  in marvell_read_status_page_an()
1653 	if (!fiber) {  in marvell_read_status_page_an()
1664 		/* The fiber link is only 1000M capable */  in marvell_read_status_page_an()
1665 		fiber_lpa_mod_linkmode_lpa_t(phydev->lp_advertising, lpa);  in marvell_read_status_page_an()
1667 		if (phydev->duplex == DUPLEX_FULL) {  in marvell_read_status_page_an()
1669 				phydev->pause = 0;  in marvell_read_status_page_an()
1670 				phydev->asym_pause = 0;  in marvell_read_status_page_an()
1672 				phydev->pause = 1;  in marvell_read_status_page_an()
1673 				phydev->asym_pause = 1;  in marvell_read_status_page_an()
1675 				phydev->pause = 1;  in marvell_read_status_page_an()
1676 				phydev->asym_pause = 0;  in marvell_read_status_page_an()
1695 	int fiber;  in marvell_read_status_page()  local
1703 	 * and the PHY status register for fiber link status.  in marvell_read_status_page()
1706 		phydev->link = !!(status & MII_M1011_PHY_STATUS_LINK);  in marvell_read_status_page()
1714 		fiber = 1;  in marvell_read_status_page()
1716 		fiber = 0;  in marvell_read_status_page()
1718 	linkmode_zero(phydev->lp_advertising);  in marvell_read_status_page()
1719 	phydev->pause = 0;  in marvell_read_status_page()
1720 	phydev->asym_pause = 0;  in marvell_read_status_page()
1721 	phydev->speed = SPEED_UNKNOWN;  in marvell_read_status_page()
1722 	phydev->duplex = DUPLEX_UNKNOWN;  in marvell_read_status_page()
1723 	phydev->port = fiber ? PORT_FIBRE : PORT_TP;  in marvell_read_status_page()
1725 	if (phydev->autoneg == AUTONEG_ENABLE)  in marvell_read_status_page()
1726 		err = marvell_read_status_page_an(phydev, fiber, status);  in marvell_read_status_page()
1735  * Some Marvell's phys have two modes: fiber and copper.
1738  *   First, check the fiber link and status.
1739  *   If the fiber link is down, check the copper link and status which
1746 	/* Check the fiber mode first */  in marvell_read_status()
1748 			      phydev->supported) &&  in marvell_read_status()
1749 	    phydev->interface != PHY_INTERFACE_MODE_SGMII) {  in marvell_read_status()
1758 		/* If the fiber link is up, it is the selected and  in marvell_read_status()
1760 		 * fiber page. Please to be careful about that, avoid  in marvell_read_status()
1762 		 * could break the behaviour for some fiber phy like  in marvell_read_status()
1765 		if (phydev->link)  in marvell_read_status()
1768 		/* If fiber link is down, check and save copper mode state */  in marvell_read_status()
1783  * Some Marvell's phys have two modes: fiber and copper.
1790 	/* Suspend the fiber mode first */  in marvell_suspend()
1792 			      phydev->supported)) {  in marvell_suspend()
1818  * Some Marvell's phys have two modes: fiber and copper.
1825 	/* Resume the fiber mode first */  in marvell_resume()
1827 			      phydev->supported)) {  in marvell_resume()
1863 	wol->supported = WAKE_MAGIC | WAKE_PHY;  in m88e1318_get_wol()
1864 	wol->wolopts = 0;  in m88e1318_get_wol()
1872 		wol->wolopts |= WAKE_MAGIC;  in m88e1318_get_wol()
1875 		wol->wolopts |= WAKE_PHY;  in m88e1318_get_wol()
1887 	if (wol->wolopts & (WAKE_MAGIC | WAKE_PHY)) {  in m88e1318_set_wol()
1921 	if (wol->wolopts & WAKE_MAGIC) {  in m88e1318_set_wol()
1928 				((phydev->attached_dev->dev_addr[5] << 8) |  in m88e1318_set_wol()
1929 				 phydev->attached_dev->dev_addr[4]));  in m88e1318_set_wol()
1933 				((phydev->attached_dev->dev_addr[3] << 8) |  in m88e1318_set_wol()
1934 				 phydev->attached_dev->dev_addr[2]));  in m88e1318_set_wol()
1938 				((phydev->attached_dev->dev_addr[1] << 8) |  in m88e1318_set_wol()
1939 				 phydev->attached_dev->dev_addr[0]));  in m88e1318_set_wol()
1962 	if (wol->wolopts & WAKE_PHY) {  in m88e1318_set_wol()
1993 			      phydev->supported))  in marvell_get_sset_count()
1996 		return ARRAY_SIZE(marvell_hw_stats) - NB_FIBER_STATS;  in marvell_get_sset_count()
2029 	struct marvell_priv *priv = phydev->priv;  in marvell_get_stat()
2037 		val = val & ((1 << stat.bits) - 1);  in marvell_get_stat()
2038 		priv->stats[i] += val;  in marvell_get_stat()
2039 		ret = priv->stats[i];  in marvell_get_stat()
2048 	struct marvell_priv *priv = phydev->priv;  in marvell_get_stat_simple()
2056 		val = val & ((1 << stat.bits) - 1);  in marvell_get_stat_simple()
2057 		priv->stats[i] += val;  in marvell_get_stat_simple()
2058 		ret = priv->stats[i];  in marvell_get_stat_simple()
2091 		bmcr_ctl = mii_bmcr_encode_fixed(phydev->speed, phydev->duplex);  in m88e1510_loopback()
2097 		if (phydev->speed == SPEED_1000)  in m88e1510_loopback()
2099 		else if (phydev->speed == SPEED_100)  in m88e1510_loopback()
2118 			 * into/out-of loopback mode.  in m88e1510_loopback()
2147 	return -ETIMEDOUT;  in marvell_vct5_wait_complete()
2166 		amplitude = -amplitude;  in marvell_vct5_amplitude()
2220 	struct marvell_priv *priv = phydev->priv;  in marvell_vct5_amplitude_graph()
2227 	if (priv->first <= TDR_SHORT_CABLE_LENGTH)  in marvell_vct5_amplitude_graph()
2251 	for (distance = priv->first;  in marvell_vct5_amplitude_graph()
2252 	     distance <= priv->last;  in marvell_vct5_amplitude_graph()
2253 	     distance += priv->step) {  in marvell_vct5_amplitude_graph()
2255 						      priv->pair);  in marvell_vct5_amplitude_graph()
2279 	/* If auto-negotiation is enabled, but not complete, the cable  in marvell_cable_test_start_common()
2280 	 * test never completes. So disable auto-neg.  in marvell_cable_test_start_common()
2309 	struct marvell_priv *priv = phydev->priv;  in marvell_vct7_cable_test_start()
2316 	priv->cable_test_tdr = false;  in marvell_vct7_cable_test_start()
2344 	struct marvell_priv *priv = phydev->priv;  in marvell_vct5_cable_test_tdr_start()
2347 	priv->cable_test_tdr = true;  in marvell_vct5_cable_test_tdr_start()
2348 	priv->first = marvell_vct5_cm2distance(cfg->first);  in marvell_vct5_cable_test_tdr_start()
2349 	priv->last = marvell_vct5_cm2distance(cfg->last);  in marvell_vct5_cable_test_tdr_start()
2350 	priv->step = marvell_vct5_cm2distance(cfg->step);  in marvell_vct5_cable_test_tdr_start()
2351 	priv->pair = cfg->pair;  in marvell_vct5_cable_test_tdr_start()
2353 	if (priv->first > MII_VCT5_SAMPLE_POINT_DISTANCE_MAX)  in marvell_vct5_cable_test_tdr_start()
2354 		return -EINVAL;  in marvell_vct5_cable_test_tdr_start()
2356 	if (priv->last > MII_VCT5_SAMPLE_POINT_DISTANCE_MAX)  in marvell_vct5_cable_test_tdr_start()
2357 		return -EINVAL;  in marvell_vct5_cable_test_tdr_start()
2374 				     marvell_vct5_distance2cm(priv->first),  in marvell_vct5_cable_test_tdr_start()
2375 				     marvell_vct5_distance2cm(priv->last),  in marvell_vct5_cable_test_tdr_start()
2376 				     marvell_vct5_distance2cm(priv->step));  in marvell_vct5_cable_test_tdr_start()
2482 	struct marvell_priv *priv = phydev->priv;  in marvell_vct7_cable_test_get_status()
2485 	if (priv->cable_test_tdr) {  in marvell_vct7_cable_test_get_status()
2510 	struct marvell_priv *priv = phydev->priv;  in m88e3082_vct_cable_test_start()
2523 	if (priv->vct_phase == M88E3082_VCT_PHASE1) {  in m88e3082_vct_cable_test_start()
2550 	if (priv->vct_phase == M88E3082_VCT_OFF) {  in m88e3082_vct_cable_test_start()
2551 		priv->vct_phase = M88E3082_VCT_PHASE1;  in m88e3082_vct_cable_test_start()
2552 		priv->pair = 0;  in m88e3082_vct_cable_test_start()
2565 	priv->vct_phase = M88E3082_VCT_PHASE2;  in m88e3082_vct_cable_test_start()
2591 	/* Original function for meters: y = 0.7861x - 18.862 */  in m88e3082_vct_distrfln_2_cm()
2592 	return (7861 * distrfln - 188620) / 100;  in m88e3082_vct_distrfln_2_cm()
2599 	struct marvell_priv *priv = phydev->priv;  in m88e3082_vct_cable_test_get_status()
2625 	switch (priv->vct_phase) {  in m88e3082_vct_cable_test_get_status()
2639 			priv->pair |= M88E3082_PAIR_A;  in m88e3082_vct_cable_test_get_status()
2649 			priv->pair |= M88E3082_PAIR_B;  in m88e3082_vct_cable_test_get_status()
2659 		if (priv->pair & M88E3082_PAIR_A &&  in m88e3082_vct_cable_test_get_status()
2667 		if (priv->pair & M88E3082_PAIR_B &&  in m88e3082_vct_cable_test_get_status()
2678 		return -EINVAL;  in m88e3082_vct_cable_test_get_status()
2686 		priv->vct_phase = M88E3082_VCT_OFF;  in m88e3082_vct_cable_test_get_status()
2737 	/* Original function for meters: y = 0.8018x - 28.751 */  in m88e1111_vct_distrfln_2_cm()
2738 	return (8018 * distrfln - 287510) / 100;  in m88e1111_vct_distrfln_2_cm()
2749 	/* Each pair use one page: A-0, B-1, C-2, D-3 */  in m88e1111_vct_cable_test_get_status()
2788 	return phydev->drv->driver_data;  in to_marvell_hwmon_ops()
2828 	*temp = ((val & MII_88E1121_MISC_TEST_TEMP_MASK) - 5) * 5000;  in m88e1121_get_temp()
2845 	*temp = ((ret & MII_88E1510_TEMP_SENSOR_MASK) - 25) * 1000;  in m88e1510_get_temp()
2862 		  MII_88E1510_MISC_TEST_TEMP_THRESHOLD_SHIFT) * 5) - 25;  in m88e1510_get_temp_critical()
2935 	*temp = (sum  - 75) * 1000;  in m88e6390_get_temp()
2962 	*temp -= 50000;  in m88e6393_get_temp()
2979 		  MII_88E6393_TEMP_SENSOR_THRESHOLD_SHIFT) - 75) * 1000;  in m88e6393_get_temp_critical()
3017 	int err = -EOPNOTSUPP;  in marvell_hwmon_read()
3021 		if (ops->get_temp)  in marvell_hwmon_read()
3022 			err = ops->get_temp(phydev, temp);  in marvell_hwmon_read()
3025 		if (ops->get_temp_critical)  in marvell_hwmon_read()
3026 			err = ops->get_temp_critical(phydev, temp);  in marvell_hwmon_read()
3029 		if (ops->get_temp_alarm)  in marvell_hwmon_read()
3030 			err = ops->get_temp_alarm(phydev, temp);  in marvell_hwmon_read()
3042 	int err = -EOPNOTSUPP;  in marvell_hwmon_write()
3046 		if (ops->set_temp_critical)  in marvell_hwmon_write()
3047 			err = ops->set_temp_critical(phydev, temp);  in marvell_hwmon_write()
3066 		return ops->get_temp ? 0444 : 0;  in marvell_hwmon_is_visible()
3068 		return ops->get_temp_alarm ? 0444 : 0;  in marvell_hwmon_is_visible()
3070 		return (ops->get_temp_critical ? 0444 : 0) |  in marvell_hwmon_is_visible()
3071 		       (ops->set_temp_critical ? 0200 : 0);  in marvell_hwmon_is_visible()
3120 	struct marvell_priv *priv = phydev->priv;  in marvell_hwmon_name()
3121 	struct device *dev = &phydev->mdio.dev;  in marvell_hwmon_name()
3126 	priv->hwmon_name = devm_kzalloc(dev, len, GFP_KERNEL);  in marvell_hwmon_name()
3127 	if (!priv->hwmon_name)  in marvell_hwmon_name()
3128 		return -ENOMEM;  in marvell_hwmon_name()
3132 			priv->hwmon_name[j++] = devname[i];  in marvell_hwmon_name()
3141 	struct marvell_priv *priv = phydev->priv;  in marvell_hwmon_probe()
3142 	struct device *dev = &phydev->mdio.dev;  in marvell_hwmon_probe()
3152 	priv->hwmon_dev = devm_hwmon_device_register_with_info(  in marvell_hwmon_probe()
3153 		dev, priv->hwmon_name, phydev, &marvell_hwmon_chip_info, NULL);  in marvell_hwmon_probe()
3154 	if (IS_ERR(priv->hwmon_dev))  in marvell_hwmon_probe()
3155 		return PTR_ERR(priv->hwmon_dev);  in marvell_hwmon_probe()
3157 	if (ops->config)  in marvell_hwmon_probe()
3158 		err = ops->config(phydev);  in marvell_hwmon_probe()
3219 		return -EINVAL;  in m88e1318_led_brightness_set()
3248 		return -EINVAL;  in m88e1318_led_blink_set()
3256 	int mode;  member
3262 		.mode = 0,
3266 		.mode = 1,
3272 		.mode = 3,
3277 		.mode = 4,
3282 		.mode = 5,
3286 		.mode = 6,
3290 		.mode = 7,
3294 		.mode = 8,
3301 		.mode = 1,
3307 		.mode = 2,
3312 		.mode = 3,
3317 		.mode = 4,
3322 		.mode = 6,
3327 		.mode = 7,
3331 		.mode = 8,
3338 		.mode = 0,
3342 		.mode = 1,
3348 		.mode = 3,
3353 		.mode = 4,
3358 		.mode = 5,
3362 		.mode = 6,
3367 		.mode = 7,
3371 		.mode = 8,
3379 				 int *mode)  in marvell_find_led_mode()  argument
3385 			*mode = marvell_rules[i].mode;  in marvell_find_led_mode()
3389 	return -EOPNOTSUPP;  in marvell_find_led_mode()
3392 static int marvell_get_led_mode(u8 index, unsigned long rules, int *mode)  in marvell_get_led_mode()  argument
3399 					    ARRAY_SIZE(marvell_led0), mode);  in marvell_get_led_mode()
3403 					    ARRAY_SIZE(marvell_led1), mode);  in marvell_get_led_mode()
3407 					    ARRAY_SIZE(marvell_led2), mode);  in marvell_get_led_mode()
3410 		ret = -EINVAL;  in marvell_get_led_mode()
3419 				  int mode)  in marvell_find_led_rules()  argument
3424 		if (marvell_rules[i].mode == mode) {  in marvell_find_led_rules()
3429 	return -EOPNOTSUPP;  in marvell_find_led_rules()
3432 static int marvell_get_led_rules(u8 index, unsigned long *rules, int mode)  in marvell_get_led_rules()  argument
3439 					     ARRAY_SIZE(marvell_led0), mode);  in marvell_get_led_rules()
3443 					     ARRAY_SIZE(marvell_led1), mode);  in marvell_get_led_rules()
3447 					     ARRAY_SIZE(marvell_led2), mode);  in marvell_get_led_rules()
3450 		ret = -EOPNOTSUPP;  in marvell_get_led_rules()
3459 	int mode, ret;  in m88e1318_led_hw_is_supported()  local
3465 		ret = marvell_get_led_mode(index, rules, &mode);  in m88e1318_led_hw_is_supported()
3468 		ret = -EINVAL;  in m88e1318_led_hw_is_supported()
3477 	int mode, ret, reg;  in m88e1318_led_hw_control_set()  local
3483 		ret = marvell_get_led_mode(index, rules, &mode);  in m88e1318_led_hw_control_set()
3486 		ret = -EINVAL;  in m88e1318_led_hw_control_set()
3498 	reg |= mode << (4 * index);  in m88e1318_led_hw_control_set()
3506 	int mode, reg;  in m88e1318_led_hw_control_get()  local
3509 		return -EINVAL;  in m88e1318_led_hw_control_get()
3516 	mode = (reg >> (4 * index)) & 0xf;  in m88e1318_led_hw_control_get()
3518 	return marvell_get_led_rules(index, rules, mode);  in m88e1318_led_hw_control_get()
3525 	priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);  in marvell_probe()
3527 		return -ENOMEM;  in marvell_probe()
3529 	phydev->priv = priv;  in marvell_probe()
3542 	u16 mode;  in m88e1510_sfp_insert()  local
3546 	dev = &phydev->mdio.dev;  in m88e1510_sfp_insert()
3548 	sfp_parse_support(phydev->sfp_bus, id, supported, interfaces);  in m88e1510_sfp_insert()
3549 	interface = sfp_select_interface(phydev->sfp_bus, supported);  in m88e1510_sfp_insert()
3555 		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X;  in m88e1510_sfp_insert()
3559 		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX;  in m88e1510_sfp_insert()
3563 		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII;  in m88e1510_sfp_insert()
3569 		return -EINVAL;  in m88e1510_sfp_insert()
3577 			   MII_88E1510_GEN_CTRL_REG_1_MODE_MASK, mode);  in m88e1510_sfp_insert()