Lines Matching +full:adc +full:- +full:use +full:- +full:res
1 # SPDX-License-Identifier: GPL-2.0-only
17 tristate "ADC Ladder Buttons"
21 to an ADC using a resistor ladder.
23 Say Y here if your device has such buttons connected to an ADC. Your
24 board-specific setup logic must also provide a configuration data
38 be called adp5520-keys.
47 Say Y here if you want to use a ADP5588/87 attached to your
51 module will be called adp5588-keys.
57 Say Y here if you want to use a ADP5585/ADP5589 attached to your
61 module will be called adp5589-keys.
111 Say Y here if you want to use a standard AT or PS/2 keyboard. Usually
122 bool "Use HP keyboard scancodes"
126 Say Y here if you have a PA-RISC machine and want to use an AT or
128 PA-RISC keyboards.
130 Say N if you use a standard keyboard.
133 bool "Use PrecisionBook keyboard scancodes"
137 If you have an RDI PrecisionBook, say Y here if you want to use its
138 built-in keyboard (as opposed to an external keyboard).
151 If you say N here, and use the PrecisionBook keyboard, then each key
152 in the left-hand column will be interpreted as the corresponding key
153 in the right-hand column.
155 If you say Y here, and use an external keyboard, then each key in the
156 right-hand column will be interpreted as the key shown in the
157 left-hand column.
164 Say Y here if you want to use Microchip AT42QT1050 QTouch
174 Say Y here if you want to use Atmel AT42QT1070 QTouch
199 module will be called clps711x-keypad.
202 tristate "D-Link DIR-685 touchkeys support"
206 If you say yes here you get support for the D-Link DIR-685
210 module will be called dlink-dir685-touchkeys.
216 Say Y here if you want to use a LK201 or LK401 style serial
242 directly to such GPIO pins. Your board-specific
257 directly to such GPIO pins. Your board-specific
272 TCA6416/TCA6408A IO expander. Your board-specific setup logic
273 must also provide pin-mask details(of which TCA6416 pins
314 The "Human Interface Loop" is a older, 8-channel USB-like
334 The "Human Interface Loop" is a older, 8-channel USB-like
336 This driver implements support for HIL-keyboards and pointing
345 support the built-in keyboard.
355 support the built-in keyboard.
396 Say Y here if you want to use NXP LPC32XX SoC key scanner interface,
400 module will be called lpc32xx-keys.
466 module will be called scmi-imx-bbm-key.
488 tristate "TI-NSPIRE built-in keyboard"
492 Say Y here if you want to use the built-in keypad on TI-NSPIRE.
495 module will be called nspire-keypad.
502 Say Y here if you want to use a matrix keyboard connected directly
506 module will be called tegra-kbc.
512 Say Y here if you want to use the OpenCores Keyboard Controller
516 module will be called opencores-kbd.
526 https://megous.com/git/pinephone-keyboard/
529 module will be called pinephone-keyboard.
548 to support up to 18x8 matrix-based keypad design.
551 be called pmic8xxx-keypad.
558 Say Y here if you want to use the keypad on your Samsung mobile
562 module will be called samsung-keypad.
572 module will be called goldfish-events.
579 Stowaway compatible keyboards like Dicota Input-PDA keyboard
590 Say Y here if you want to use a keypad attached to the keyscan block
594 module will be called st-keyscan.
600 Say Y here if you want to use a Sun Type 4 or Type 5 keyboard,
602 (RS-232) port via a simple adapter.
611 Say Y here if you want to use a keypad attached to the KEYSC block
623 Say Y here if you want to use the keypad controller on STMPE I/O
627 called stmpe-keypad.
630 tristate "Allwinner sun4i low res adc attached tablet keys support"
633 This selects support for the Allwinner low res adc attached tablet
637 module will be called sun4i-lradc-keys.
647 module will be called ipaq-micro-keys.
654 IQS621, IQS622, IQS624 and IQS625 multi-function sensors.
657 be called iqs62x-keys.
664 Say Y here if you want to use the OMAP keypad.
667 module will be called omap-keypad.
674 Say Y here if you want to use the OMAP4+ keypad.
677 module will be called omap4-keypad.
684 Say Y here if you want to use the SPEAR keyboard.
687 module will be called spear-keyboard.
694 Say Y here if you want to use the keypad controller on
698 module will be called tc3589x-keypad.
705 Say Y here to enable device driver for tm2-touchkey with
709 module will be called tm2-touchkey.
716 Say Y here if your board use the keypad controller on
718 even on boards that don't use the keypad controller.
727 Say Y here if you want to use the old IBM PC/XT keyboard (or
743 (CROS_EC_I2C or CROS_EC_SPI) to use this.
764 Say Y here if you want to use Broadcom keypad.
767 module will be called bcm-keypad.
775 Say Y here if you want to use the keypad on MediaTek SoCs.
779 module will be called mt6779-keypad.
785 Say Y here if you want to use the pmic keys (powerkey/homekey).
788 module will be called pmic-keys.
798 module will be called cypress-sf.