Lines Matching +full:lvds +full:- +full:decoder
1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Eagle board with R-Car V3M
5 * Copyright (C) 2016-2017 Renesas Electronics Corp.
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
29 stdout-path = "serial0:115200n8";
32 d1p8: regulator-fixed {
33 compatible = "regulator-fixed";
34 regulator-name = "fixed-1.8V";
35 regulator-min-microvolt = <1800000>;
36 regulator-max-microvolt = <1800000>;
37 regulator-boot-on;
38 regulator-always-on;
41 d3p3: regulator-fixed {
42 compatible = "regulator-fixed";
43 regulator-name = "fixed-3.3V";
44 regulator-min-microvolt = <3300000>;
45 regulator-max-microvolt = <3300000>;
46 regulator-boot-on;
47 regulator-always-on;
50 hdmi-out {
51 compatible = "hdmi-connector";
56 remote-endpoint = <&adv7511_out>;
61 lvds-decoder {
64 vcc-supply = <&d3p3>;
67 #address-cells = <1>;
68 #size-cells = <0>;
73 remote-endpoint = <&lvds0_out>;
80 remote-endpoint = <&adv7511_in>;
92 x1_clk: x1-clock {
93 compatible = "fixed-clock";
94 #clock-cells = <0>;
95 clock-frequency = <148500000>;
100 pinctrl-0 = <&avb_pins>;
101 pinctrl-names = "default";
103 renesas,no-ether-link;
104 phy-handle = <&phy0>;
105 rx-internal-delay-ps = <1800>;
106 tx-internal-delay-ps = <2000>;
109 phy0: ethernet-phy@0 {
110 compatible = "ethernet-phy-id0022.1622",
111 "ethernet-phy-ieee802.3-c22";
112 rxc-skew-ps = <1500>;
114 interrupt-parent = <&gpio1>;
116 reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
121 pinctrl-0 = <&canfd0_pins>;
122 pinctrl-names = "default";
136 clock-lanes = <0>;
137 data-lanes = <1 2 3 4>;
138 remote-endpoint = <&max9286_out0>;
146 clock-names = "du.0", "dclkin.0";
151 clock-frequency = <16666666>;
155 clock-frequency = <32768>;
159 pinctrl-0 = <&i2c0_pins>;
160 pinctrl-names = "default";
163 clock-frequency = <400000>;
168 gpio-controller;
169 #gpio-cells = <2>;
175 interrupt-parent = <&gpio1>;
178 avdd-supply = <&d1p8>;
179 dvdd-supply = <&d1p8>;
180 pvdd-supply = <&d1p8>;
181 dvdd-3v-supply = <&d3p3>;
182 bgvdd-supply = <&d1p8>;
184 adi,input-depth = <8>;
185 adi,input-colorspace = "rgb";
186 adi,input-clock = "1x";
189 #address-cells = <1>;
190 #size-cells = <0>;
195 remote-endpoint = <&thc63lvd1024_out>;
202 remote-endpoint = <&hdmi_con_out>;
210 pinctrl-0 = <&i2c3_pins>;
211 pinctrl-names = "default";
214 clock-frequency = <400000>;
216 gmsl0: gmsl-deserializer@48 {
220 maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
221 enable-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
224 #address-cells = <1>;
225 #size-cells = <0>;
246 clock-lanes = <0>;
247 data-lanes = <1 2 3 4>;
248 remote-endpoint = <&csi40_in>;
253 i2c-mux {
254 #address-cells = <1>;
255 #size-cells = <0>;
258 #address-cells = <1>;
259 #size-cells = <0>;
266 #address-cells = <1>;
267 #size-cells = <0>;
274 #address-cells = <1>;
275 #size-cells = <0>;
282 #address-cells = <1>;
283 #size-cells = <0>;
298 remote-endpoint = <&thc63lvd1024_in>;
305 pinctrl-0 = <&scif_clk_pins>;
306 pinctrl-names = "default";
345 pinctrl-0 = <&qspi0_pins>;
346 pinctrl-names = "default";
351 compatible = "spansion,s25fs512s", "jedec,spi-nor";
353 spi-max-frequency = <50000000>;
354 spi-rx-bus-width = <4>;
357 compatible = "fixed-partitions";
358 #address-cells = <1>;
359 #size-cells = <1>;
363 read-only;
367 read-only;
371 read-only;
375 read-only;
379 read-only;
383 read-only;
387 read-only;
389 uboot-env@700000 {
391 read-only;
407 timeout-sec = <60>;
412 pinctrl-0 = <&scif0_pins>;
413 pinctrl-names = "default";
419 clock-frequency = <14745600>;