Lines Matching +full:lvds +full:- +full:decoder
1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Ebisu/Ebisu-4D board
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
33 stdout-path = "serial0:115200n8";
36 audio_clkout: audio-clkout {
39 * but needed to avoid cs2000/rcar_sound probe dead-lock
41 compatible = "fixed-clock";
42 #clock-cells = <0>;
43 clock-frequency = <11289600>;
47 compatible = "pwm-backlight";
50 brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
51 default-brightness-level = <10>;
53 power-supply = <®_12p0v>;
56 cvbs-in {
57 compatible = "composite-video-connector";
62 remote-endpoint = <&adv7482_ain7>;
67 hdmi-in {
68 compatible = "hdmi-connector";
74 remote-endpoint = <&adv7482_hdmi>;
79 hdmi-out {
80 compatible = "hdmi-connector";
85 remote-endpoint = <&adv7511_out>;
91 compatible = "gpio-keys";
93 pinctrl-0 = <&keys_pins>;
94 pinctrl-names = "default";
96 key-1 {
99 label = "SW4-1";
100 wakeup-source;
101 debounce-interval = <20>;
103 key-2 {
106 label = "SW4-2";
107 wakeup-source;
108 debounce-interval = <20>;
110 key-3 {
113 label = "SW4-3";
114 wakeup-source;
115 debounce-interval = <20>;
117 key-4 {
120 label = "SW4-4";
121 wakeup-source;
122 debounce-interval = <20>;
126 lvds-decoder {
128 vcc-supply = <®_3p3v>;
131 #address-cells = <1>;
132 #size-cells = <0>;
137 remote-endpoint = <&lvds0_out>;
144 remote-endpoint = <&adv7511_in>;
156 reg_1p8v: regulator-1p8v {
157 compatible = "regulator-fixed";
158 regulator-name = "fixed-1.8V";
159 regulator-min-microvolt = <1800000>;
160 regulator-max-microvolt = <1800000>;
161 regulator-boot-on;
162 regulator-always-on;
165 reg_3p3v: regulator-3p3v {
166 compatible = "regulator-fixed";
167 regulator-name = "fixed-3.3V";
168 regulator-min-microvolt = <3300000>;
169 regulator-max-microvolt = <3300000>;
170 regulator-boot-on;
171 regulator-always-on;
174 reg_12p0v: regulator-12p0v {
175 compatible = "regulator-fixed";
176 regulator-name = "D12.0V";
177 regulator-min-microvolt = <12000000>;
178 regulator-max-microvolt = <12000000>;
179 regulator-boot-on;
180 regulator-always-on;
184 compatible = "simple-audio-card";
186 simple-audio-card,name = "rsnd-ak4613";
187 simple-audio-card,format = "left_j";
188 simple-audio-card,bitclock-master = <&sndcpu>;
189 simple-audio-card,frame-master = <&sndcpu>;
191 sndcodec: simple-audio-card,codec {
192 sound-dai = <&ak4613>;
195 sndcpu: simple-audio-card,cpu {
196 sound-dai = <&rcar_sound>;
200 vbus0_usb2: regulator-vbus0-usb2 {
201 compatible = "regulator-fixed";
203 regulator-name = "USB20_VBUS_CN";
204 regulator-min-microvolt = <5000000>;
205 regulator-max-microvolt = <5000000>;
208 enable-active-high;
211 vcc_sdhi0: regulator-vcc-sdhi0 {
212 compatible = "regulator-fixed";
214 regulator-name = "SDHI0 Vcc";
215 regulator-min-microvolt = <3300000>;
216 regulator-max-microvolt = <3300000>;
219 enable-active-high;
222 vccq_sdhi0: regulator-vccq-sdhi0 {
223 compatible = "regulator-gpio";
225 regulator-name = "SDHI0 VccQ";
226 regulator-min-microvolt = <1800000>;
227 regulator-max-microvolt = <3300000>;
230 gpios-states = <1>;
234 vcc_sdhi1: regulator-vcc-sdhi1 {
235 compatible = "regulator-fixed";
237 regulator-name = "SDHI1 Vcc";
238 regulator-min-microvolt = <3300000>;
239 regulator-max-microvolt = <3300000>;
242 enable-active-high;
245 vccq_sdhi1: regulator-vccq-sdhi1 {
246 compatible = "regulator-gpio";
248 regulator-name = "SDHI1 VccQ";
249 regulator-min-microvolt = <1800000>;
250 regulator-max-microvolt = <3300000>;
253 gpios-states = <1>;
258 compatible = "vga-connector";
262 remote-endpoint = <&adv7123_out>;
267 vga-encoder {
271 #address-cells = <1>;
272 #size-cells = <0>;
277 remote-endpoint = <&du_out_rgb>;
283 remote-endpoint = <&vga_in>;
290 compatible = "fixed-clock";
291 #clock-cells = <0>;
292 clock-frequency = <24576000>;
296 compatible = "fixed-clock";
297 #clock-cells = <0>;
298 clock-frequency = <74250000>;
303 clock-frequency = <22579200>;
307 pinctrl-0 = <&avb_pins>;
308 pinctrl-names = "default";
309 phy-handle = <&phy0>;
312 phy0: ethernet-phy@0 {
313 compatible = "ethernet-phy-id0022.1622",
314 "ethernet-phy-ieee802.3-c22";
315 rxc-skew-ps = <1500>;
317 interrupt-parent = <&gpio2>;
319 reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
324 * isn't supported on R-Car E3(e). Thus, limit speed to
327 max-speed = <100>;
332 pinctrl-0 = <&canfd0_pins>;
333 pinctrl-names = "default";
347 clock-lanes = <0>;
348 data-lanes = <1 2>;
349 remote-endpoint = <&adv7482_txa>;
356 pinctrl-0 = <&du_pins>;
357 pinctrl-names = "default";
363 clock-names = "du.0", "du.1", "dclkin.0";
368 remote-endpoint = <&adv7123_in>;
380 clock-frequency = <48000000>;
394 gpio-controller;
395 #gpio-cells = <2>;
396 interrupt-parent = <&gpio2>;
400 hdmi-encoder@39 {
403 interrupt-parent = <&gpio1>;
406 avdd-supply = <®_1p8v>;
407 dvdd-supply = <®_1p8v>;
408 pvdd-supply = <®_1p8v>;
409 dvdd-3v-supply = <®_3p3v>;
410 bgvdd-supply = <®_1p8v>;
412 adi,input-depth = <8>;
413 adi,input-colorspace = "rgb";
414 adi,input-clock = "1x";
417 #address-cells = <1>;
418 #size-cells = <0>;
423 remote-endpoint = <&thc63lvd1024_out>;
430 remote-endpoint = <&hdmi_con_out>;
436 video-receiver@70 {
440 interrupt-parent = <&gpio0>;
441 interrupt-names = "intrq1", "intrq2";
446 #address-cells = <1>;
447 #size-cells = <0>;
453 remote-endpoint = <&cvbs_con>;
461 remote-endpoint = <&hdmi_in_con>;
469 clock-lanes = <0>;
470 data-lanes = <1 2>;
471 remote-endpoint = <&csi40_in>;
482 compatible = "asahi-kasei,ak4613";
483 #sound-dai-cells = <0>;
487 asahi-kasei,in1-single-end;
488 asahi-kasei,in2-single-end;
489 asahi-kasei,out1-single-end;
490 asahi-kasei,out2-single-end;
491 asahi-kasei,out3-single-end;
492 asahi-kasei,out4-single-end;
493 asahi-kasei,out5-single-end;
494 asahi-kasei,out6-single-end;
497 cs2000: clk-multiplier@4f {
498 #clock-cells = <0>;
499 compatible = "cirrus,cs2000-cp";
502 clock-names = "clk_in", "ref_clk";
504 assigned-clocks = <&cs2000>;
505 assigned-clock-rates = <24576000>; /* 1/1 divide */
512 clock-frequency = <400000>;
515 pinctrl-0 = <&irq0_pins>;
516 pinctrl-names = "default";
520 interrupt-parent = <&intc_ex>;
522 interrupt-controller;
523 #interrupt-cells = <2>;
524 gpio-controller;
525 #gpio-cells = <2>;
526 rohm,ddr-backup-power = <0x1>;
527 rohm,rstbmode-level;
543 clock-names = "fck", "dclkin.0", "extal";
548 remote-endpoint = <&thc63lvd1024_in>;
565 clock-names = "fck", "dclkin.0", "extal";
574 clock-frequency = <100000000>;
604 bias-pull-up;
631 power-source = <3300>;
637 power-source = <1800>;
643 power-source = <3300>;
649 power-source = <1800>;
655 power-source = <1800>;
681 pinctrl-0 = <&pwm3_pins>;
682 pinctrl-names = "default";
688 pinctrl-0 = <&pwm5_pins>;
689 pinctrl-names = "default";
695 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
696 pinctrl-names = "default";
699 #sound-dai-cells = <0>;
702 #clock-cells = <1>;
703 clock-frequency = <12288000 11289600>;
735 pinctrl-0 = <&rpc_pins>;
736 pinctrl-names = "default";
741 compatible = "cypress,hyperflash", "cfi-flash";
745 compatible = "fixed-partitions";
746 #address-cells = <1>;
747 #size-cells = <1>;
751 read-only;
755 read-only;
759 read-only;
763 read-only;
767 read-only;
771 read-only;
787 timeout-sec = <60>;
792 pinctrl-0 = <&scif2_pins>;
793 pinctrl-names = "default";
799 pinctrl-0 = <&sdhi0_pins>;
800 pinctrl-1 = <&sdhi0_pins_uhs>;
801 pinctrl-names = "default", "state_uhs";
803 vmmc-supply = <&vcc_sdhi0>;
804 vqmmc-supply = <&vccq_sdhi0>;
805 cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
806 wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
807 bus-width = <4>;
808 sd-uhs-sdr50;
809 sd-uhs-sdr104;
814 pinctrl-0 = <&sdhi1_pins>;
815 pinctrl-1 = <&sdhi1_pins_uhs>;
816 pinctrl-names = "default", "state_uhs";
818 vmmc-supply = <&vcc_sdhi1>;
819 vqmmc-supply = <&vccq_sdhi1>;
820 cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
821 bus-width = <4>;
822 sd-uhs-sdr50;
823 sd-uhs-sdr104;
828 /* used for on-board 8bit eMMC */
829 pinctrl-0 = <&sdhi3_pins>;
830 pinctrl-1 = <&sdhi3_pins>;
831 pinctrl-names = "default", "state_uhs";
833 vmmc-supply = <®_3p3v>;
834 vqmmc-supply = <®_1p8v>;
835 mmc-hs200-1_8v;
836 mmc-hs400-1_8v;
837 bus-width = <8>;
838 no-sd;
839 no-sdio;
840 non-removable;
841 full-pwr-cycle-in-suspend;
846 shared-pin;
850 pinctrl-0 = <&usb0_pins>;
851 pinctrl-names = "default";
853 vbus-supply = <&vbus0_usb2>;
871 pinctrl-0 = <&usb30_pins>;
872 pinctrl-names = "default";