Lines Matching +full:vddl +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/gpio-keys.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
15 #include "x1e80100-pmics.dtsi"
19 compatible = "qcom,x1e80100-crd", "qcom,x1e80100";
25 wcd938x: audio-codec {
26 compatible = "qcom,wcd9385-codec";
28 pinctrl-names = "default";
29 pinctrl-0 = <&wcd_default>;
31 qcom,micbias1-microvolt = <1800000>;
32 qcom,micbias2-microvolt = <1800000>;
33 qcom,micbias3-microvolt = <1800000>;
34 qcom,micbias4-microvolt = <1800000>;
35 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
36 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
37 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
38 qcom,rx-device = <&wcd_rx>;
39 qcom,tx-device = <&wcd_tx>;
41 reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
43 vdd-buck-supply = <&vreg_l15b_1p8>;
44 vdd-rxtx-supply = <&vreg_l15b_1p8>;
45 vdd-io-supply = <&vreg_l15b_1p8>;
46 vdd-mic-bias-supply = <&vreg_bob1>;
48 #sound-dai-cells = <1>;
52 stdout-path = "serial0:115200n8";
55 gpio-keys {
56 compatible = "gpio-keys";
58 pinctrl-0 = <&hall_int_n_default>;
59 pinctrl-names = "default";
61 switch-lid {
63 linux,input-type = <EV_SW>;
65 wakeup-source;
66 wakeup-event-action = <EV_ACT_DEASSERTED>;
70 pmic-glink {
71 compatible = "qcom,x1e80100-pmic-glink",
72 "qcom,sm8550-pmic-glink",
73 "qcom,pmic-glink";
74 #address-cells = <1>;
75 #size-cells = <0>;
76 orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
80 /* Left-side rear port */
82 compatible = "usb-c-connector";
84 power-role = "dual";
85 data-role = "dual";
88 #address-cells = <1>;
89 #size-cells = <0>;
95 remote-endpoint = <&usb_1_ss0_dwc3_hs>;
103 remote-endpoint = <&usb_1_ss0_qmpphy_out>;
109 /* Left-side front port */
111 compatible = "usb-c-connector";
113 power-role = "dual";
114 data-role = "dual";
117 #address-cells = <1>;
118 #size-cells = <0>;
124 remote-endpoint = <&usb_1_ss1_dwc3_hs>;
132 remote-endpoint = <&usb_1_ss1_qmpphy_out>;
138 /* Right-side port */
140 compatible = "usb-c-connector";
142 power-role = "dual";
143 data-role = "dual";
146 #address-cells = <1>;
147 #size-cells = <0>;
153 remote-endpoint = <&usb_1_ss2_dwc3_hs>;
161 remote-endpoint = <&usb_1_ss2_qmpphy_out>;
168 reserved-memory {
170 compatible = "shared-dma-pool";
173 linux,cma-default;
178 compatible = "qcom,x1e80100-sndcard";
179 model = "X1E80100-CRD";
180 audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
197 wcd-playback-dai-link {
198 link-name = "WCD Playback";
201 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
205 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
209 sound-dai = <&q6apm>;
213 wcd-capture-dai-link {
214 link-name = "WCD Capture";
217 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
221 sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
225 sound-dai = <&q6apm>;
229 wsa-dai-link {
230 link-name = "WSA Playback";
233 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
237 sound-dai = <&left_woofer>, <&left_tweeter>,
244 sound-dai = <&q6apm>;
248 va-dai-link {
249 link-name = "VA Capture";
252 sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
256 sound-dai = <&lpass_vamacro 0>;
260 sound-dai = <&q6apm>;
265 vreg_edp_3p3: regulator-edp-3p3 {
266 compatible = "regulator-fixed";
268 regulator-name = "VREG_EDP_3P3";
269 regulator-min-microvolt = <3300000>;
270 regulator-max-microvolt = <3300000>;
273 enable-active-high;
275 pinctrl-0 = <&edp_reg_en>;
276 pinctrl-names = "default";
278 regulator-boot-on;
281 vreg_misc_3p3: regulator-misc-3p3 {
282 compatible = "regulator-fixed";
284 regulator-name = "VREG_MISC_3P3";
285 regulator-min-microvolt = <3300000>;
286 regulator-max-microvolt = <3300000>;
289 enable-active-high;
291 pinctrl-names = "default";
292 pinctrl-0 = <&misc_3p3_reg_en>;
294 regulator-boot-on;
295 regulator-always-on;
298 vreg_nvme: regulator-nvme {
299 compatible = "regulator-fixed";
301 regulator-name = "VREG_NVME_3P3";
302 regulator-min-microvolt = <3300000>;
303 regulator-max-microvolt = <3300000>;
306 enable-active-high;
308 pinctrl-names = "default";
309 pinctrl-0 = <&nvme_reg_en>;
311 regulator-boot-on;
314 vph_pwr: regulator-vph-pwr {
315 compatible = "regulator-fixed";
317 regulator-name = "vph_pwr";
318 regulator-min-microvolt = <3700000>;
319 regulator-max-microvolt = <3700000>;
321 regulator-always-on;
322 regulator-boot-on;
325 vreg_wwan: regulator-wwan {
326 compatible = "regulator-fixed";
328 regulator-name = "SDX_VPH_PWR";
329 regulator-min-microvolt = <3300000>;
330 regulator-max-microvolt = <3300000>;
333 enable-active-high;
335 pinctrl-0 = <&wwan_sw_en>;
336 pinctrl-names = "default";
338 regulator-boot-on;
343 regulators-0 {
344 compatible = "qcom,pm8550-rpmh-regulators";
345 qcom,pmic-id = "b";
347 vdd-bob1-supply = <&vph_pwr>;
348 vdd-bob2-supply = <&vph_pwr>;
349 vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
350 vdd-l2-l13-l14-supply = <&vreg_bob1>;
351 vdd-l5-l16-supply = <&vreg_bob1>;
352 vdd-l6-l7-supply = <&vreg_bob2>;
353 vdd-l8-l9-supply = <&vreg_bob1>;
354 vdd-l12-supply = <&vreg_s5j_1p2>;
355 vdd-l15-supply = <&vreg_s4c_1p8>;
356 vdd-l17-supply = <&vreg_bob2>;
359 regulator-name = "vreg_bob1";
360 regulator-min-microvolt = <3008000>;
361 regulator-max-microvolt = <3960000>;
362 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
366 regulator-name = "vreg_bob2";
367 regulator-min-microvolt = <2504000>;
368 regulator-max-microvolt = <3008000>;
369 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
373 regulator-name = "vreg_l1b_1p8";
374 regulator-min-microvolt = <1800000>;
375 regulator-max-microvolt = <1800000>;
376 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
380 regulator-name = "vreg_l2b_3p0";
381 regulator-min-microvolt = <3072000>;
382 regulator-max-microvolt = <3100000>;
383 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
387 regulator-name = "vreg_l4b_1p8";
388 regulator-min-microvolt = <1800000>;
389 regulator-max-microvolt = <1800000>;
390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
394 regulator-name = "vreg_l5b_3p0";
395 regulator-min-microvolt = <3000000>;
396 regulator-max-microvolt = <3000000>;
397 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
401 regulator-name = "vreg_l6b_1p8";
402 regulator-min-microvolt = <1800000>;
403 regulator-max-microvolt = <2960000>;
404 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
408 regulator-name = "vreg_l7b_2p8";
409 regulator-min-microvolt = <2800000>;
410 regulator-max-microvolt = <2800000>;
411 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
415 regulator-name = "vreg_l8b_3p0";
416 regulator-min-microvolt = <3072000>;
417 regulator-max-microvolt = <3072000>;
418 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
422 regulator-name = "vreg_l9b_2p9";
423 regulator-min-microvolt = <2960000>;
424 regulator-max-microvolt = <2960000>;
425 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
429 regulator-name = "vreg_l10b_1p8";
430 regulator-min-microvolt = <1800000>;
431 regulator-max-microvolt = <1800000>;
432 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
436 regulator-name = "vreg_l12b_1p2";
437 regulator-min-microvolt = <1200000>;
438 regulator-max-microvolt = <1200000>;
439 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
443 regulator-name = "vreg_l13b_3p0";
444 regulator-min-microvolt = <3072000>;
445 regulator-max-microvolt = <3100000>;
446 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
450 regulator-name = "vreg_l14b_3p0";
451 regulator-min-microvolt = <3072000>;
452 regulator-max-microvolt = <3072000>;
453 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
457 regulator-name = "vreg_l15b_1p8";
458 regulator-min-microvolt = <1800000>;
459 regulator-max-microvolt = <1800000>;
460 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
464 regulator-name = "vreg_l16b_2p9";
465 regulator-min-microvolt = <2912000>;
466 regulator-max-microvolt = <2912000>;
467 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
471 regulator-name = "vreg_l17b_2p5";
472 regulator-min-microvolt = <2504000>;
473 regulator-max-microvolt = <2504000>;
474 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
478 regulators-1 {
479 compatible = "qcom,pm8550ve-rpmh-regulators";
480 qcom,pmic-id = "c";
482 vdd-l1-supply = <&vreg_s5j_1p2>;
483 vdd-l2-supply = <&vreg_s1f_0p7>;
484 vdd-l3-supply = <&vreg_s1f_0p7>;
485 vdd-s4-supply = <&vph_pwr>;
488 regulator-name = "vreg_s4c_1p8";
489 regulator-min-microvolt = <1856000>;
490 regulator-max-microvolt = <2000000>;
491 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
495 regulator-name = "vreg_l1c_1p2";
496 regulator-min-microvolt = <1200000>;
497 regulator-max-microvolt = <1200000>;
498 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
502 regulator-name = "vreg_l2c_0p8";
503 regulator-min-microvolt = <880000>;
504 regulator-max-microvolt = <920000>;
505 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
509 regulator-name = "vreg_l3c_0p8";
510 regulator-min-microvolt = <880000>;
511 regulator-max-microvolt = <920000>;
512 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
516 regulators-2 {
517 compatible = "qcom,pmc8380-rpmh-regulators";
518 qcom,pmic-id = "d";
520 vdd-l1-supply = <&vreg_s1f_0p7>;
521 vdd-l2-supply = <&vreg_s1f_0p7>;
522 vdd-l3-supply = <&vreg_s4c_1p8>;
523 vdd-s1-supply = <&vph_pwr>;
526 regulator-name = "vreg_l1d_0p8";
527 regulator-min-microvolt = <880000>;
528 regulator-max-microvolt = <920000>;
529 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
533 regulator-name = "vreg_l2d_0p9";
534 regulator-min-microvolt = <912000>;
535 regulator-max-microvolt = <920000>;
536 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
540 regulator-name = "vreg_l3d_1p8";
541 regulator-min-microvolt = <1800000>;
542 regulator-max-microvolt = <1800000>;
543 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
547 regulators-3 {
548 compatible = "qcom,pmc8380-rpmh-regulators";
549 qcom,pmic-id = "e";
551 vdd-l2-supply = <&vreg_s1f_0p7>;
552 vdd-l3-supply = <&vreg_s5j_1p2>;
555 regulator-name = "vreg_l2e_0p8";
556 regulator-min-microvolt = <880000>;
557 regulator-max-microvolt = <920000>;
558 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
562 regulator-name = "vreg_l3e_1p2";
563 regulator-min-microvolt = <1200000>;
564 regulator-max-microvolt = <1200000>;
565 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
569 regulators-4 {
570 compatible = "qcom,pmc8380-rpmh-regulators";
571 qcom,pmic-id = "f";
573 vdd-l1-supply = <&vreg_s5j_1p2>;
574 vdd-l2-supply = <&vreg_s5j_1p2>;
575 vdd-l3-supply = <&vreg_s5j_1p2>;
576 vdd-s1-supply = <&vph_pwr>;
579 regulator-name = "vreg_s1f_0p7";
580 regulator-min-microvolt = <700000>;
581 regulator-max-microvolt = <1100000>;
582 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
586 regulator-name = "vreg_l1f_1p0";
587 regulator-min-microvolt = <1024000>;
588 regulator-max-microvolt = <1024000>;
589 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
593 regulator-name = "vreg_l2f_1p0";
594 regulator-min-microvolt = <1024000>;
595 regulator-max-microvolt = <1024000>;
596 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
600 regulator-name = "vreg_l3f_1p0";
601 regulator-min-microvolt = <1024000>;
602 regulator-max-microvolt = <1024000>;
603 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
607 regulators-6 {
608 compatible = "qcom,pm8550ve-rpmh-regulators";
609 qcom,pmic-id = "i";
611 vdd-l1-supply = <&vreg_s4c_1p8>;
612 vdd-l2-supply = <&vreg_s5j_1p2>;
613 vdd-l3-supply = <&vreg_s1f_0p7>;
614 vdd-s1-supply = <&vph_pwr>;
615 vdd-s2-supply = <&vph_pwr>;
618 regulator-name = "vreg_s1i_0p9";
619 regulator-min-microvolt = <900000>;
620 regulator-max-microvolt = <920000>;
621 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
625 regulator-name = "vreg_s2i_1p0";
626 regulator-min-microvolt = <1000000>;
627 regulator-max-microvolt = <1100000>;
628 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
632 regulator-name = "vreg_l1i_1p8";
633 regulator-min-microvolt = <1800000>;
634 regulator-max-microvolt = <1800000>;
635 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
639 regulator-name = "vreg_l2i_1p2";
640 regulator-min-microvolt = <1200000>;
641 regulator-max-microvolt = <1200000>;
642 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
646 regulator-name = "vreg_l3i_0p8";
647 regulator-min-microvolt = <880000>;
648 regulator-max-microvolt = <920000>;
649 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
653 regulators-7 {
654 compatible = "qcom,pm8550ve-rpmh-regulators";
655 qcom,pmic-id = "j";
657 vdd-l1-supply = <&vreg_s1f_0p7>;
658 vdd-l2-supply = <&vreg_s5j_1p2>;
659 vdd-l3-supply = <&vreg_s1f_0p7>;
660 vdd-s5-supply = <&vph_pwr>;
663 regulator-name = "vreg_s5j_1p2";
664 regulator-min-microvolt = <1256000>;
665 regulator-max-microvolt = <1304000>;
666 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
670 regulator-name = "vreg_l1j_0p8";
671 regulator-min-microvolt = <880000>;
672 regulator-max-microvolt = <920000>;
673 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
677 regulator-name = "vreg_l2j_1p2";
678 regulator-min-microvolt = <1200000>;
679 regulator-max-microvolt = <1200000>;
680 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
684 regulator-name = "vreg_l3j_0p8";
685 regulator-min-microvolt = <880000>;
686 regulator-max-microvolt = <920000>;
687 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
695 zap-shader {
696 firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
701 clock-frequency = <400000>;
706 compatible = "hid-over-i2c";
709 hid-descr-addr = <0x1>;
710 interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
712 vdd-supply = <&vreg_misc_3p3>;
713 vddl-supply = <&vreg_l12b_1p2>;
715 pinctrl-0 = <&tpad_default>;
716 pinctrl-names = "default";
718 wakeup-source;
722 compatible = "hid-over-i2c";
725 hid-descr-addr = <0x1>;
726 interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
728 vdd-supply = <&vreg_misc_3p3>;
729 vddl-supply = <&vreg_l12b_1p2>;
731 pinctrl-0 = <&kybd_default>;
732 pinctrl-names = "default";
734 wakeup-source;
739 clock-frequency = <400000>;
744 compatible = "hid-over-i2c";
747 hid-descr-addr = <0x1>;
748 interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
750 vdd-supply = <&vreg_misc_3p3>;
751 vddl-supply = <&vreg_l15b_1p8>;
753 pinctrl-0 = <&ts0_default>;
754 pinctrl-names = "default";
759 spkr_01_sd_n_active: spkr-01-sd-n-active-state {
762 drive-strength = <16>;
763 bias-disable;
764 output-low;
767 spkr_23_sd_n_active: spkr-23-sd-n-active-state {
770 drive-strength = <16>;
771 bias-disable;
772 output-low;
777 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
778 pinctrl-names = "default";
780 vdd-micb-supply = <&vreg_l1b_1p8>;
781 qcom,dmic-sample-rate = <4800000>;
789 compatible = "qcom,x1e80100-dp";
790 /delete-property/ #sound-dai-cells;
794 aux-bus {
797 enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
798 power-supply = <&vreg_edp_3p3>;
800 pinctrl-0 = <&edp_bl_en>;
801 pinctrl-names = "default";
805 remote-endpoint = <&mdss_dp3_out>;
815 data-lanes = <0 1 2 3>;
816 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
818 remote-endpoint = <&edp_panel_in>;
825 vdda-phy-supply = <&vreg_l3j_0p8>;
826 vdda-pll-supply = <&vreg_l2j_1p2>;
832 perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
833 wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
835 pinctrl-0 = <&pcie4_default>;
836 pinctrl-names = "default";
842 vdda-phy-supply = <&vreg_l3i_0p8>;
843 vdda-pll-supply = <&vreg_l3e_1p2>;
849 perst-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
850 wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
852 vddpe-3v3-supply = <&vreg_wwan>;
854 pinctrl-0 = <&pcie5_default>;
855 pinctrl-names = "default";
861 vdda-phy-supply = <&vreg_l3i_0p8>;
862 vdda-pll-supply = <&vreg_l3e_1p2>;
868 perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
869 wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
871 vddpe-3v3-supply = <&vreg_nvme>;
873 pinctrl-names = "default";
874 pinctrl-0 = <&pcie6a_default>;
880 vdda-phy-supply = <&vreg_l1d_0p8>;
881 vdda-pll-supply = <&vreg_l2j_1p2>;
887 misc_3p3_reg_en: misc-3p3-reg-en-state {
890 bias-disable;
891 input-disable;
892 output-enable;
893 drive-push-pull;
894 power-source = <1>; /* 1.8 V */
895 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
900 edp_bl_en: edp-bl-en-state {
903 power-source = <1>; /* 1.8V */
904 input-disable;
905 output-enable;
922 firmware-name = "qcom/x1e80100/adsp.mbn",
929 firmware-name = "qcom/x1e80100/cdsp.mbn",
936 vdd18-supply = <&vreg_l3d_1p8>;
937 vdd3-supply = <&vreg_l2b_3p0>;
941 vdd18-supply = <&vreg_l3d_1p8>;
942 vdd3-supply = <&vreg_l14b_3p0>;
950 vdd18-supply = <&vreg_l3d_1p8>;
951 vdd3-supply = <&vreg_l8b_3p0>;
957 pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
958 pinctrl-names = "default";
964 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
965 #sound-dai-cells = <0>;
966 sound-name-prefix = "WooferLeft";
967 vdd-1p8-supply = <&vreg_l15b_1p8>;
968 vdd-io-supply = <&vreg_l12b_1p2>;
969 qcom,port-mapping = <1 2 3 7 10 13>;
976 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
977 #sound-dai-cells = <0>;
978 sound-name-prefix = "TweeterLeft";
979 vdd-1p8-supply = <&vreg_l15b_1p8>;
980 vdd-io-supply = <&vreg_l12b_1p2>;
981 qcom,port-mapping = <4 5 6 7 11 13>;
992 qcom,rx-port-mapping = <1 2 3 4 5>;
1003 qcom,tx-port-mapping = <2 2 3 4>;
1010 pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
1011 pinctrl-names = "default";
1017 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
1018 #sound-dai-cells = <0>;
1019 sound-name-prefix = "WooferRight";
1020 vdd-1p8-supply = <&vreg_l15b_1p8>;
1021 vdd-io-supply = <&vreg_l12b_1p2>;
1022 qcom,port-mapping = <1 2 3 7 10 13>;
1029 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
1030 #sound-dai-cells = <0>;
1031 sound-name-prefix = "TweeterRight";
1032 vdd-1p8-supply = <&vreg_l15b_1p8>;
1033 vdd-io-supply = <&vreg_l12b_1p2>;
1034 qcom,port-mapping = <4 5 6 7 11 13>;
1039 gpio-reserved-ranges = <34 2>, /* Unused */
1043 edp_reg_en: edp-reg-en-state {
1046 drive-strength = <16>;
1047 bias-disable;
1050 hall_int_n_default: hall-int-n-state {
1053 bias-disable;
1056 kybd_default: kybd-default-state {
1059 bias-disable;
1062 nvme_reg_en: nvme-reg-en-state {
1065 drive-strength = <2>;
1066 bias-disable;
1069 pcie4_default: pcie4-default-state {
1070 clkreq-n-pins {
1073 drive-strength = <2>;
1074 bias-pull-up;
1077 perst-n-pins {
1080 drive-strength = <2>;
1081 bias-disable;
1084 wake-n-pins {
1087 drive-strength = <2>;
1088 bias-pull-up;
1092 pcie5_default: pcie5-default-state {
1093 clkreq-n-pins {
1096 drive-strength = <2>;
1097 bias-pull-up;
1100 perst-n-pins {
1103 drive-strength = <2>;
1104 bias-disable;
1107 wake-n-pins {
1110 drive-strength = <2>;
1111 bias-pull-up;
1115 pcie6a_default: pcie6a-default-state {
1116 clkreq-n-pins {
1119 drive-strength = <2>;
1120 bias-pull-up;
1123 perst-n-pins {
1126 drive-strength = <2>;
1127 bias-disable;
1130 wake-n-pins {
1133 drive-strength = <2>;
1134 bias-pull-up;
1138 tpad_default: tpad-default-state {
1141 bias-disable;
1144 ts0_default: ts0-default-state {
1145 int-n-pins {
1148 bias-disable;
1151 reset-n-pins {
1154 output-high;
1155 drive-strength = <16>;
1159 wcd_default: wcd-reset-n-active-state {
1162 drive-strength = <16>;
1163 bias-disable;
1164 output-low;
1167 wwan_sw_en: wwan-sw-en-state {
1170 drive-strength = <4>;
1171 bias-disable;
1176 compatible = "qcom,geni-debug-uart";
1181 vdd-supply = <&vreg_l3j_0p8>;
1182 vdda12-supply = <&vreg_l2j_1p2>;
1190 vdda-phy-supply = <&vreg_l3e_1p2>;
1191 vdda-pll-supply = <&vreg_l1j_0p8>;
1201 remote-endpoint = <&pmic_glink_ss0_hs_in>;
1205 remote-endpoint = <&pmic_glink_ss0_ss_in>;
1209 vdd-supply = <&vreg_l3j_0p8>;
1210 vdda12-supply = <&vreg_l2j_1p2>;
1218 vdda-phy-supply = <&vreg_l3e_1p2>;
1219 vdda-pll-supply = <&vreg_l2d_0p9>;
1229 remote-endpoint = <&pmic_glink_ss1_hs_in>;
1233 remote-endpoint = <&pmic_glink_ss1_ss_in>;
1237 vdd-supply = <&vreg_l3j_0p8>;
1238 vdda12-supply = <&vreg_l2j_1p2>;
1246 vdda-phy-supply = <&vreg_l3e_1p2>;
1247 vdda-pll-supply = <&vreg_l2d_0p9>;
1257 remote-endpoint = <&pmic_glink_ss2_hs_in>;
1261 remote-endpoint = <&pmic_glink_ss2_ss_in>;