Lines Matching +full:vdd +full:- +full:io
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/gpio-keys.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
14 #include "x1e80100-pmics.dtsi"
18 compatible = "qcom,x1e80100-crd", "qcom,x1e80100";
24 wcd938x: audio-codec {
25 compatible = "qcom,wcd9385-codec";
27 pinctrl-names = "default";
28 pinctrl-0 = <&wcd_default>;
30 qcom,micbias1-microvolt = <1800000>;
31 qcom,micbias2-microvolt = <1800000>;
32 qcom,micbias3-microvolt = <1800000>;
33 qcom,micbias4-microvolt = <1800000>;
34 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
35 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
36 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
37 qcom,rx-device = <&wcd_rx>;
38 qcom,tx-device = <&wcd_tx>;
40 reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
42 vdd-buck-supply = <&vreg_l15b_1p8>;
43 vdd-rxtx-supply = <&vreg_l15b_1p8>;
44 vdd-io-supply = <&vreg_l15b_1p8>;
45 vdd-mic-bias-supply = <&vreg_bob1>;
47 #sound-dai-cells = <1>;
51 stdout-path = "serial0:115200n8";
54 gpio-keys {
55 compatible = "gpio-keys";
57 pinctrl-0 = <&hall_int_n_default>;
58 pinctrl-names = "default";
60 switch-lid {
62 linux,input-type = <EV_SW>;
64 wakeup-source;
65 wakeup-event-action = <EV_ACT_DEASSERTED>;
69 pmic-glink {
70 compatible = "qcom,x1e80100-pmic-glink",
71 "qcom,sm8550-pmic-glink",
72 "qcom,pmic-glink";
73 #address-cells = <1>;
74 #size-cells = <0>;
75 orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
79 /* Left-side rear port */
81 compatible = "usb-c-connector";
83 power-role = "dual";
84 data-role = "dual";
87 #address-cells = <1>;
88 #size-cells = <0>;
94 remote-endpoint = <&usb_1_ss0_dwc3_hs>;
102 remote-endpoint = <&usb_1_ss0_qmpphy_out>;
108 /* Left-side front port */
110 compatible = "usb-c-connector";
112 power-role = "dual";
113 data-role = "dual";
116 #address-cells = <1>;
117 #size-cells = <0>;
123 remote-endpoint = <&usb_1_ss1_dwc3_hs>;
131 remote-endpoint = <&usb_1_ss1_qmpphy_out>;
137 /* Right-side port */
139 compatible = "usb-c-connector";
141 power-role = "dual";
142 data-role = "dual";
145 #address-cells = <1>;
146 #size-cells = <0>;
152 remote-endpoint = <&usb_1_ss2_dwc3_hs>;
160 remote-endpoint = <&usb_1_ss2_qmpphy_out>;
167 reserved-memory {
169 compatible = "shared-dma-pool";
172 linux,cma-default;
177 compatible = "qcom,x1e80100-sndcard";
178 model = "X1E80100-CRD";
179 audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
196 wcd-playback-dai-link {
197 link-name = "WCD Playback";
200 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
204 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
208 sound-dai = <&q6apm>;
212 wcd-capture-dai-link {
213 link-name = "WCD Capture";
216 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
220 sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
224 sound-dai = <&q6apm>;
228 wsa-dai-link {
229 link-name = "WSA Playback";
232 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
236 sound-dai = <&left_woofer>, <&left_tweeter>,
243 sound-dai = <&q6apm>;
247 va-dai-link {
248 link-name = "VA Capture";
251 sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
255 sound-dai = <&lpass_vamacro 0>;
259 sound-dai = <&q6apm>;
264 vph_pwr: vph-pwr-regulator {
265 compatible = "regulator-fixed";
267 regulator-name = "vph_pwr";
268 regulator-min-microvolt = <3700000>;
269 regulator-max-microvolt = <3700000>;
271 regulator-always-on;
272 regulator-boot-on;
275 vreg_edp_3p3: regulator-edp-3p3 {
276 compatible = "regulator-fixed";
278 regulator-name = "VREG_EDP_3P3";
279 regulator-min-microvolt = <3300000>;
280 regulator-max-microvolt = <3300000>;
283 enable-active-high;
285 pinctrl-0 = <&edp_reg_en>;
286 pinctrl-names = "default";
288 regulator-boot-on;
291 vreg_nvme: regulator-nvme {
292 compatible = "regulator-fixed";
294 regulator-name = "VREG_NVME_3P3";
295 regulator-min-microvolt = <3300000>;
296 regulator-max-microvolt = <3300000>;
299 enable-active-high;
301 pinctrl-names = "default";
302 pinctrl-0 = <&nvme_reg_en>;
304 regulator-boot-on;
307 vreg_wwan: regulator-wwan {
308 compatible = "regulator-fixed";
310 regulator-name = "SDX_VPH_PWR";
311 regulator-min-microvolt = <3300000>;
312 regulator-max-microvolt = <3300000>;
315 enable-active-high;
317 pinctrl-0 = <&wwan_sw_en>;
318 pinctrl-names = "default";
320 regulator-boot-on;
325 regulators-0 {
326 compatible = "qcom,pm8550-rpmh-regulators";
327 qcom,pmic-id = "b";
329 vdd-bob1-supply = <&vph_pwr>;
330 vdd-bob2-supply = <&vph_pwr>;
331 vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
332 vdd-l2-l13-l14-supply = <&vreg_bob1>;
333 vdd-l5-l16-supply = <&vreg_bob1>;
334 vdd-l6-l7-supply = <&vreg_bob2>;
335 vdd-l8-l9-supply = <&vreg_bob1>;
336 vdd-l12-supply = <&vreg_s5j_1p2>;
337 vdd-l15-supply = <&vreg_s4c_1p8>;
338 vdd-l17-supply = <&vreg_bob2>;
341 regulator-name = "vreg_bob1";
342 regulator-min-microvolt = <3008000>;
343 regulator-max-microvolt = <3960000>;
344 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
348 regulator-name = "vreg_bob2";
349 regulator-min-microvolt = <2504000>;
350 regulator-max-microvolt = <3008000>;
351 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
355 regulator-name = "vreg_l1b_1p8";
356 regulator-min-microvolt = <1800000>;
357 regulator-max-microvolt = <1800000>;
358 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
362 regulator-name = "vreg_l2b_3p0";
363 regulator-min-microvolt = <3072000>;
364 regulator-max-microvolt = <3100000>;
365 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
369 regulator-name = "vreg_l4b_1p8";
370 regulator-min-microvolt = <1800000>;
371 regulator-max-microvolt = <1800000>;
372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
376 regulator-name = "vreg_l5b_3p0";
377 regulator-min-microvolt = <3000000>;
378 regulator-max-microvolt = <3000000>;
379 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
383 regulator-name = "vreg_l6b_1p8";
384 regulator-min-microvolt = <1800000>;
385 regulator-max-microvolt = <2960000>;
386 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
390 regulator-name = "vreg_l7b_2p8";
391 regulator-min-microvolt = <2800000>;
392 regulator-max-microvolt = <2800000>;
393 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
397 regulator-name = "vreg_l8b_3p0";
398 regulator-min-microvolt = <3072000>;
399 regulator-max-microvolt = <3072000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
404 regulator-name = "vreg_l9b_2p9";
405 regulator-min-microvolt = <2960000>;
406 regulator-max-microvolt = <2960000>;
407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
411 regulator-name = "vreg_l10b_1p8";
412 regulator-min-microvolt = <1800000>;
413 regulator-max-microvolt = <1800000>;
414 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
418 regulator-name = "vreg_l12b_1p2";
419 regulator-min-microvolt = <1200000>;
420 regulator-max-microvolt = <1200000>;
421 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
425 regulator-name = "vreg_l13b_3p0";
426 regulator-min-microvolt = <3072000>;
427 regulator-max-microvolt = <3100000>;
428 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
432 regulator-name = "vreg_l14b_3p0";
433 regulator-min-microvolt = <3072000>;
434 regulator-max-microvolt = <3072000>;
435 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
439 regulator-name = "vreg_l15b_1p8";
440 regulator-min-microvolt = <1800000>;
441 regulator-max-microvolt = <1800000>;
442 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
446 regulator-name = "vreg_l16b_2p9";
447 regulator-min-microvolt = <2912000>;
448 regulator-max-microvolt = <2912000>;
449 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
453 regulator-name = "vreg_l17b_2p5";
454 regulator-min-microvolt = <2504000>;
455 regulator-max-microvolt = <2504000>;
456 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
460 regulators-1 {
461 compatible = "qcom,pm8550ve-rpmh-regulators";
462 qcom,pmic-id = "c";
464 vdd-l1-supply = <&vreg_s5j_1p2>;
465 vdd-l2-supply = <&vreg_s1f_0p7>;
466 vdd-l3-supply = <&vreg_s1f_0p7>;
467 vdd-s4-supply = <&vph_pwr>;
470 regulator-name = "vreg_s4c_1p8";
471 regulator-min-microvolt = <1856000>;
472 regulator-max-microvolt = <2000000>;
473 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
477 regulator-name = "vreg_l1c_1p2";
478 regulator-min-microvolt = <1200000>;
479 regulator-max-microvolt = <1200000>;
480 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
484 regulator-name = "vreg_l2c_0p8";
485 regulator-min-microvolt = <880000>;
486 regulator-max-microvolt = <920000>;
487 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
491 regulator-name = "vreg_l3c_0p8";
492 regulator-min-microvolt = <880000>;
493 regulator-max-microvolt = <920000>;
494 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
498 regulators-2 {
499 compatible = "qcom,pmc8380-rpmh-regulators";
500 qcom,pmic-id = "d";
502 vdd-l1-supply = <&vreg_s1f_0p7>;
503 vdd-l2-supply = <&vreg_s1f_0p7>;
504 vdd-l3-supply = <&vreg_s4c_1p8>;
505 vdd-s1-supply = <&vph_pwr>;
508 regulator-name = "vreg_l1d_0p8";
509 regulator-min-microvolt = <880000>;
510 regulator-max-microvolt = <920000>;
511 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
515 regulator-name = "vreg_l2d_0p9";
516 regulator-min-microvolt = <912000>;
517 regulator-max-microvolt = <920000>;
518 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
522 regulator-name = "vreg_l3d_1p8";
523 regulator-min-microvolt = <1800000>;
524 regulator-max-microvolt = <1800000>;
525 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
529 regulators-3 {
530 compatible = "qcom,pmc8380-rpmh-regulators";
531 qcom,pmic-id = "e";
533 vdd-l2-supply = <&vreg_s1f_0p7>;
534 vdd-l3-supply = <&vreg_s5j_1p2>;
537 regulator-name = "vreg_l2e_0p8";
538 regulator-min-microvolt = <880000>;
539 regulator-max-microvolt = <920000>;
540 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
544 regulator-name = "vreg_l3e_1p2";
545 regulator-min-microvolt = <1200000>;
546 regulator-max-microvolt = <1200000>;
547 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
551 regulators-4 {
552 compatible = "qcom,pmc8380-rpmh-regulators";
553 qcom,pmic-id = "f";
555 vdd-l1-supply = <&vreg_s5j_1p2>;
556 vdd-l2-supply = <&vreg_s5j_1p2>;
557 vdd-l3-supply = <&vreg_s5j_1p2>;
558 vdd-s1-supply = <&vph_pwr>;
561 regulator-name = "vreg_s1f_0p7";
562 regulator-min-microvolt = <700000>;
563 regulator-max-microvolt = <1100000>;
564 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
568 regulator-name = "vreg_l1f_1p0";
569 regulator-min-microvolt = <1024000>;
570 regulator-max-microvolt = <1024000>;
571 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
575 regulator-name = "vreg_l2f_1p0";
576 regulator-min-microvolt = <1024000>;
577 regulator-max-microvolt = <1024000>;
578 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
582 regulator-name = "vreg_l3f_1p0";
583 regulator-min-microvolt = <1024000>;
584 regulator-max-microvolt = <1024000>;
585 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
589 regulators-6 {
590 compatible = "qcom,pm8550ve-rpmh-regulators";
591 qcom,pmic-id = "i";
593 vdd-l1-supply = <&vreg_s4c_1p8>;
594 vdd-l2-supply = <&vreg_s5j_1p2>;
595 vdd-l3-supply = <&vreg_s1f_0p7>;
596 vdd-s1-supply = <&vph_pwr>;
597 vdd-s2-supply = <&vph_pwr>;
600 regulator-name = "vreg_s1i_0p9";
601 regulator-min-microvolt = <900000>;
602 regulator-max-microvolt = <920000>;
603 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
607 regulator-name = "vreg_s2i_1p0";
608 regulator-min-microvolt = <1000000>;
609 regulator-max-microvolt = <1100000>;
610 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
614 regulator-name = "vreg_l1i_1p8";
615 regulator-min-microvolt = <1800000>;
616 regulator-max-microvolt = <1800000>;
617 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
621 regulator-name = "vreg_l2i_1p2";
622 regulator-min-microvolt = <1200000>;
623 regulator-max-microvolt = <1200000>;
624 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
628 regulator-name = "vreg_l3i_0p8";
629 regulator-min-microvolt = <880000>;
630 regulator-max-microvolt = <920000>;
631 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
635 regulators-7 {
636 compatible = "qcom,pm8550ve-rpmh-regulators";
637 qcom,pmic-id = "j";
639 vdd-l1-supply = <&vreg_s1f_0p7>;
640 vdd-l2-supply = <&vreg_s5j_1p2>;
641 vdd-l3-supply = <&vreg_s1f_0p7>;
642 vdd-s5-supply = <&vph_pwr>;
645 regulator-name = "vreg_s5j_1p2";
646 regulator-min-microvolt = <1256000>;
647 regulator-max-microvolt = <1304000>;
648 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
652 regulator-name = "vreg_l1j_0p8";
653 regulator-min-microvolt = <880000>;
654 regulator-max-microvolt = <920000>;
655 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
659 regulator-name = "vreg_l2j_1p2";
660 regulator-min-microvolt = <1200000>;
661 regulator-max-microvolt = <1200000>;
662 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
666 regulator-name = "vreg_l3j_0p8";
667 regulator-min-microvolt = <880000>;
668 regulator-max-microvolt = <920000>;
669 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
677 zap-shader {
678 firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
683 clock-frequency = <400000>;
688 compatible = "hid-over-i2c";
691 hid-descr-addr = <0x1>;
692 interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
694 pinctrl-0 = <&tpad_default>;
695 pinctrl-names = "default";
697 wakeup-source;
701 compatible = "hid-over-i2c";
704 hid-descr-addr = <0x1>;
705 interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
707 pinctrl-0 = <&kybd_default>;
708 pinctrl-names = "default";
710 wakeup-source;
715 clock-frequency = <400000>;
720 compatible = "hid-over-i2c";
723 hid-descr-addr = <0x1>;
724 interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
726 pinctrl-0 = <&ts0_default>;
727 pinctrl-names = "default";
732 spkr_01_sd_n_active: spkr-01-sd-n-active-state {
735 drive-strength = <16>;
736 bias-disable;
737 output-low;
740 spkr_23_sd_n_active: spkr-23-sd-n-active-state {
743 drive-strength = <16>;
744 bias-disable;
745 output-low;
750 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
751 pinctrl-names = "default";
753 vdd-micb-supply = <&vreg_l1b_1p8>;
754 qcom,dmic-sample-rate = <4800000>;
762 compatible = "qcom,x1e80100-dp";
763 /delete-property/ #sound-dai-cells;
767 aux-bus {
770 enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
771 power-supply = <&vreg_edp_3p3>;
773 pinctrl-0 = <&edp_bl_en>;
774 pinctrl-names = "default";
778 remote-endpoint = <&mdss_dp3_out>;
788 data-lanes = <0 1 2 3>;
789 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
791 remote-endpoint = <&edp_panel_in>;
798 vdda-phy-supply = <&vreg_l3j_0p8>;
799 vdda-pll-supply = <&vreg_l2j_1p2>;
805 perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
806 wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
808 pinctrl-0 = <&pcie4_default>;
809 pinctrl-names = "default";
815 vdda-phy-supply = <&vreg_l3i_0p8>;
816 vdda-pll-supply = <&vreg_l3e_1p2>;
822 perst-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
823 wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
825 vddpe-3v3-supply = <&vreg_wwan>;
827 pinctrl-0 = <&pcie5_default>;
828 pinctrl-names = "default";
834 vdda-phy-supply = <&vreg_l3i_0p8>;
835 vdda-pll-supply = <&vreg_l3e_1p2>;
841 perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
842 wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
844 vddpe-3v3-supply = <&vreg_nvme>;
846 pinctrl-names = "default";
847 pinctrl-0 = <&pcie6a_default>;
853 vdda-phy-supply = <&vreg_l1d_0p8>;
854 vdda-pll-supply = <&vreg_l2j_1p2>;
860 edp_bl_en: edp-bl-en-state {
863 power-source = <1>; /* 1.8V */
864 input-disable;
865 output-enable;
882 firmware-name = "qcom/x1e80100/adsp.mbn",
889 firmware-name = "qcom/x1e80100/cdsp.mbn",
896 vdd18-supply = <&vreg_l3d_1p8>;
897 vdd3-supply = <&vreg_l2b_3p0>;
901 vdd18-supply = <&vreg_l3d_1p8>;
902 vdd3-supply = <&vreg_l14b_3p0>;
910 vdd18-supply = <&vreg_l3d_1p8>;
911 vdd3-supply = <&vreg_l8b_3p0>;
917 pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
918 pinctrl-names = "default";
924 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
925 #sound-dai-cells = <0>;
926 sound-name-prefix = "WooferLeft";
927 vdd-1p8-supply = <&vreg_l15b_1p8>;
928 vdd-io-supply = <&vreg_l12b_1p2>;
929 qcom,port-mapping = <1 2 3 7 10 13>;
936 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
937 #sound-dai-cells = <0>;
938 sound-name-prefix = "TweeterLeft";
939 vdd-1p8-supply = <&vreg_l15b_1p8>;
940 vdd-io-supply = <&vreg_l12b_1p2>;
941 qcom,port-mapping = <4 5 6 7 11 13>;
952 qcom,rx-port-mapping = <1 2 3 4 5>;
963 qcom,tx-port-mapping = <2 2 3 4>;
970 pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
971 pinctrl-names = "default";
977 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
978 #sound-dai-cells = <0>;
979 sound-name-prefix = "WooferRight";
980 vdd-1p8-supply = <&vreg_l15b_1p8>;
981 vdd-io-supply = <&vreg_l12b_1p2>;
982 qcom,port-mapping = <1 2 3 7 10 13>;
989 reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
990 #sound-dai-cells = <0>;
991 sound-name-prefix = "TweeterRight";
992 vdd-1p8-supply = <&vreg_l15b_1p8>;
993 vdd-io-supply = <&vreg_l12b_1p2>;
994 qcom,port-mapping = <4 5 6 7 11 13>;
999 gpio-reserved-ranges = <34 2>, /* Unused */
1003 edp_reg_en: edp-reg-en-state {
1006 drive-strength = <16>;
1007 bias-disable;
1010 hall_int_n_default: hall-int-n-state {
1013 bias-disable;
1016 kybd_default: kybd-default-state {
1019 bias-disable;
1022 nvme_reg_en: nvme-reg-en-state {
1025 drive-strength = <2>;
1026 bias-disable;
1029 pcie4_default: pcie4-default-state {
1030 clkreq-n-pins {
1033 drive-strength = <2>;
1034 bias-pull-up;
1037 perst-n-pins {
1040 drive-strength = <2>;
1041 bias-disable;
1044 wake-n-pins {
1047 drive-strength = <2>;
1048 bias-pull-up;
1052 pcie5_default: pcie5-default-state {
1053 clkreq-n-pins {
1056 drive-strength = <2>;
1057 bias-pull-up;
1060 perst-n-pins {
1063 drive-strength = <2>;
1064 bias-disable;
1067 wake-n-pins {
1070 drive-strength = <2>;
1071 bias-pull-up;
1075 pcie6a_default: pcie6a-default-state {
1076 clkreq-n-pins {
1079 drive-strength = <2>;
1080 bias-pull-up;
1083 perst-n-pins {
1086 drive-strength = <2>;
1087 bias-disable;
1090 wake-n-pins {
1093 drive-strength = <2>;
1094 bias-pull-up;
1098 tpad_default: tpad-default-state {
1101 bias-disable;
1104 ts0_default: ts0-default-state {
1105 int-n-pins {
1108 bias-disable;
1111 reset-n-pins {
1114 output-high;
1115 drive-strength = <16>;
1119 wcd_default: wcd-reset-n-active-state {
1122 drive-strength = <16>;
1123 bias-disable;
1124 output-low;
1127 wwan_sw_en: wwan-sw-en-state {
1130 drive-strength = <4>;
1131 bias-disable;
1136 compatible = "qcom,geni-debug-uart";
1141 vdd-supply = <&vreg_l3j_0p8>;
1142 vdda12-supply = <&vreg_l2j_1p2>;
1150 vdda-phy-supply = <&vreg_l3e_1p2>;
1151 vdda-pll-supply = <&vreg_l1j_0p8>;
1165 remote-endpoint = <&pmic_glink_ss0_hs_in>;
1169 remote-endpoint = <&pmic_glink_ss0_ss_in>;
1173 vdd-supply = <&vreg_l3j_0p8>;
1174 vdda12-supply = <&vreg_l2j_1p2>;
1182 vdda-phy-supply = <&vreg_l3e_1p2>;
1183 vdda-pll-supply = <&vreg_l2d_0p9>;
1197 remote-endpoint = <&pmic_glink_ss1_hs_in>;
1201 remote-endpoint = <&pmic_glink_ss1_ss_in>;
1205 vdd-supply = <&vreg_l3j_0p8>;
1206 vdda12-supply = <&vreg_l2j_1p2>;
1214 vdda-phy-supply = <&vreg_l3e_1p2>;
1215 vdda-pll-supply = <&vreg_l2d_0p9>;
1229 remote-endpoint = <&pmic_glink_ss2_hs_in>;
1233 remote-endpoint = <&pmic_glink_ss2_ss_in>;