Lines Matching +full:wake +full:- +full:pins
1 // SPDX-License-Identifier: BSD-3-Clause
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/gpio-keys.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
15 #include "x1e80100-pmics.dtsi"
19 compatible = "lenovo,thinkpad-t14s", "qcom,x1e78100", "qcom,x1e80100";
20 chassis-type = "laptop";
22 wcd938x: audio-codec {
23 compatible = "qcom,wcd9385-codec";
25 pinctrl-0 = <&wcd_default>;
26 pinctrl-names = "default";
28 qcom,micbias1-microvolt = <1800000>;
29 qcom,micbias2-microvolt = <1800000>;
30 qcom,micbias3-microvolt = <1800000>;
31 qcom,micbias4-microvolt = <1800000>;
32 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
33 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
34 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
35 qcom,rx-device = <&wcd_rx>;
36 qcom,tx-device = <&wcd_tx>;
38 reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
40 vdd-buck-supply = <&vreg_l15b_1p8>;
41 vdd-rxtx-supply = <&vreg_l15b_1p8>;
42 vdd-io-supply = <&vreg_l15b_1p8>;
43 vdd-mic-bias-supply = <&vreg_bob1>;
45 #sound-dai-cells = <1>;
48 gpio-keys {
49 compatible = "gpio-keys";
51 pinctrl-0 = <&hall_int_n_default>;
52 pinctrl-names = "default";
54 switch-lid {
56 linux,input-type = <EV_SW>;
58 wakeup-source;
59 wakeup-event-action = <EV_ACT_DEASSERTED>;
63 pmic-glink {
64 compatible = "qcom,x1e80100-pmic-glink",
65 "qcom,sm8550-pmic-glink",
66 "qcom,pmic-glink";
67 orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
69 #address-cells = <1>;
70 #size-cells = <0>;
72 /* Display-adjacent port */
74 compatible = "usb-c-connector";
76 power-role = "dual";
77 data-role = "dual";
80 #address-cells = <1>;
81 #size-cells = <0>;
87 remote-endpoint = <&usb_1_ss0_dwc3_hs>;
95 remote-endpoint = <&usb_1_ss0_qmpphy_out>;
101 /* User-adjacent port */
103 compatible = "usb-c-connector";
105 power-role = "dual";
106 data-role = "dual";
109 #address-cells = <1>;
110 #size-cells = <0>;
116 remote-endpoint = <&usb_1_ss1_dwc3_hs>;
124 remote-endpoint = <&usb_1_ss1_qmpphy_out>;
131 reserved-memory {
133 compatible = "shared-dma-pool";
136 linux,cma-default;
140 vreg_edp_3p3: regulator-edp-3p3 {
141 compatible = "regulator-fixed";
143 regulator-name = "VREG_EDP_3P3";
144 regulator-min-microvolt = <3300000>;
145 regulator-max-microvolt = <3300000>;
148 enable-active-high;
150 pinctrl-0 = <&edp_reg_en>;
151 pinctrl-names = "default";
153 regulator-boot-on;
156 vreg_nvme: regulator-nvme {
157 compatible = "regulator-fixed";
159 regulator-name = "VREG_NVME_3P3";
160 regulator-min-microvolt = <3300000>;
161 regulator-max-microvolt = <3300000>;
164 enable-active-high;
166 pinctrl-0 = <&nvme_reg_en>;
167 pinctrl-names = "default";
169 regulator-boot-on;
172 vph_pwr: regulator-vph-pwr {
173 compatible = "regulator-fixed";
175 regulator-name = "vph_pwr";
176 regulator-min-microvolt = <3700000>;
177 regulator-max-microvolt = <3700000>;
179 regulator-always-on;
180 regulator-boot-on;
184 compatible = "qcom,x1e80100-sndcard";
185 model = "X1E80100-LENOVO-Thinkpad-T14s";
186 audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
197 wcd-playback-dai-link {
198 link-name = "WCD Playback";
201 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
205 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
209 sound-dai = <&q6apm>;
213 wcd-capture-dai-link {
214 link-name = "WCD Capture";
217 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
221 sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
225 sound-dai = <&q6apm>;
229 wsa-dai-link {
230 link-name = "WSA Playback";
233 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
237 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
241 sound-dai = <&q6apm>;
245 va-dai-link {
246 link-name = "VA Capture";
249 sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
253 sound-dai = <&lpass_vamacro 0>;
257 sound-dai = <&q6apm>;
264 regulators-0 {
265 compatible = "qcom,pm8550-rpmh-regulators";
266 qcom,pmic-id = "b";
268 vdd-bob1-supply = <&vph_pwr>;
269 vdd-bob2-supply = <&vph_pwr>;
270 vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
271 vdd-l2-l13-l14-supply = <&vreg_bob1>;
272 vdd-l5-l16-supply = <&vreg_bob1>;
273 vdd-l6-l7-supply = <&vreg_bob2>;
274 vdd-l8-l9-supply = <&vreg_bob1>;
275 vdd-l12-supply = <&vreg_s5j_1p2>;
276 vdd-l15-supply = <&vreg_s4c_1p8>;
277 vdd-l17-supply = <&vreg_bob2>;
280 regulator-name = "vreg_bob1";
281 regulator-min-microvolt = <3008000>;
282 regulator-max-microvolt = <3960000>;
283 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
287 regulator-name = "vreg_bob2";
288 regulator-min-microvolt = <2504000>;
289 regulator-max-microvolt = <3008000>;
290 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
294 regulator-name = "vreg_l1b_1p8";
295 regulator-min-microvolt = <1800000>;
296 regulator-max-microvolt = <1800000>;
297 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
301 regulator-name = "vreg_l2b_3p0";
302 regulator-min-microvolt = <3072000>;
303 regulator-max-microvolt = <3072000>;
304 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
308 regulator-name = "vreg_l4b_1p8";
309 regulator-min-microvolt = <1800000>;
310 regulator-max-microvolt = <1800000>;
311 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
315 regulator-name = "vreg_l6b_1p8";
316 regulator-min-microvolt = <1800000>;
317 regulator-max-microvolt = <2960000>;
318 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
322 regulator-name = "vreg_l8b_3p0";
323 regulator-min-microvolt = <3072000>;
324 regulator-max-microvolt = <3072000>;
325 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
329 regulator-name = "vreg_l9b_2p9";
330 regulator-min-microvolt = <2960000>;
331 regulator-max-microvolt = <2960000>;
332 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
336 regulator-name = "vreg_l10b_1p8";
337 regulator-min-microvolt = <1800000>;
338 regulator-max-microvolt = <1800000>;
339 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
343 regulator-name = "vreg_l12b_1p2";
344 regulator-min-microvolt = <1200000>;
345 regulator-max-microvolt = <1200000>;
346 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
350 regulator-name = "vreg_l13b_3p0";
351 regulator-min-microvolt = <3072000>;
352 regulator-max-microvolt = <3072000>;
353 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
357 regulator-name = "vreg_l14b_3p0";
358 regulator-min-microvolt = <3072000>;
359 regulator-max-microvolt = <3072000>;
360 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
364 regulator-name = "vreg_l15b_1p8";
365 regulator-min-microvolt = <1800000>;
366 regulator-max-microvolt = <1800000>;
367 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
371 regulator-name = "vreg_l17b_2p5";
372 regulator-min-microvolt = <2504000>;
373 regulator-max-microvolt = <2504000>;
374 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
378 regulators-1 {
379 compatible = "qcom,pm8550ve-rpmh-regulators";
380 qcom,pmic-id = "c";
382 vdd-l1-supply = <&vreg_s5j_1p2>;
383 vdd-l2-supply = <&vreg_s1f_0p7>;
384 vdd-l3-supply = <&vreg_s1f_0p7>;
385 vdd-s4-supply = <&vph_pwr>;
388 regulator-name = "vreg_s4c_1p8";
389 regulator-min-microvolt = <1856000>;
390 regulator-max-microvolt = <2000000>;
391 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
395 regulator-name = "vreg_l1c_1p2";
396 regulator-min-microvolt = <1200000>;
397 regulator-max-microvolt = <1200000>;
398 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
402 regulator-name = "vreg_l2c_0p8";
403 regulator-min-microvolt = <880000>;
404 regulator-max-microvolt = <880000>;
405 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
409 regulator-name = "vreg_l3c_0p8";
410 regulator-min-microvolt = <912000>;
411 regulator-max-microvolt = <912000>;
412 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
416 regulators-2 {
417 compatible = "qcom,pmc8380-rpmh-regulators";
418 qcom,pmic-id = "d";
420 vdd-l1-supply = <&vreg_s1f_0p7>;
421 vdd-l2-supply = <&vreg_s1f_0p7>;
422 vdd-l3-supply = <&vreg_s4c_1p8>;
423 vdd-s1-supply = <&vph_pwr>;
426 regulator-name = "vreg_l1d_0p8";
427 regulator-min-microvolt = <880000>;
428 regulator-max-microvolt = <880000>;
429 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
433 regulator-name = "vreg_l2d_0p9";
434 regulator-min-microvolt = <912000>;
435 regulator-max-microvolt = <912000>;
436 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
440 regulator-name = "vreg_l3d_1p8";
441 regulator-min-microvolt = <1800000>;
442 regulator-max-microvolt = <1800000>;
443 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
447 regulators-3 {
448 compatible = "qcom,pmc8380-rpmh-regulators";
449 qcom,pmic-id = "e";
451 vdd-l2-supply = <&vreg_s1f_0p7>;
452 vdd-l3-supply = <&vreg_s5j_1p2>;
455 regulator-name = "vreg_l2e_0p8";
456 regulator-min-microvolt = <880000>;
457 regulator-max-microvolt = <880000>;
458 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
462 regulator-name = "vreg_l3e_1p2";
463 regulator-min-microvolt = <1200000>;
464 regulator-max-microvolt = <1200000>;
465 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
469 regulators-4 {
470 compatible = "qcom,pmc8380-rpmh-regulators";
471 qcom,pmic-id = "f";
473 vdd-l1-supply = <&vreg_s5j_1p2>;
474 vdd-l2-supply = <&vreg_s5j_1p2>;
475 vdd-l3-supply = <&vreg_s5j_1p2>;
476 vdd-s1-supply = <&vph_pwr>;
479 regulator-name = "vreg_s1f_0p7";
480 regulator-min-microvolt = <700000>;
481 regulator-max-microvolt = <1100000>;
482 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
486 regulators-6 {
487 compatible = "qcom,pm8550ve-rpmh-regulators";
488 qcom,pmic-id = "i";
490 vdd-l1-supply = <&vreg_s4c_1p8>;
491 vdd-l2-supply = <&vreg_s5j_1p2>;
492 vdd-l3-supply = <&vreg_s1f_0p7>;
493 vdd-s1-supply = <&vph_pwr>;
494 vdd-s2-supply = <&vph_pwr>;
497 regulator-name = "vreg_l1i_1p8";
498 regulator-min-microvolt = <1800000>;
499 regulator-max-microvolt = <1800000>;
500 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
504 regulator-name = "vreg_l2i_1p2";
505 regulator-min-microvolt = <1200000>;
506 regulator-max-microvolt = <1200000>;
507 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
511 regulator-name = "vreg_l3i_0p8";
512 regulator-min-microvolt = <880000>;
513 regulator-max-microvolt = <880000>;
514 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
518 regulators-7 {
519 compatible = "qcom,pm8550ve-rpmh-regulators";
520 qcom,pmic-id = "j";
522 vdd-l1-supply = <&vreg_s1f_0p7>;
523 vdd-l2-supply = <&vreg_s5j_1p2>;
524 vdd-l3-supply = <&vreg_s1f_0p7>;
525 vdd-s5-supply = <&vph_pwr>;
528 regulator-name = "vreg_s5j_1p2";
529 regulator-min-microvolt = <1256000>;
530 regulator-max-microvolt = <1304000>;
531 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
535 regulator-name = "vreg_l1j_0p8";
536 regulator-min-microvolt = <912000>;
537 regulator-max-microvolt = <912000>;
538 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
542 regulator-name = "vreg_l2j_1p2";
543 regulator-min-microvolt = <1256000>;
544 regulator-max-microvolt = <1256000>;
545 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
549 regulator-name = "vreg_l3j_0p8";
550 regulator-min-microvolt = <880000>;
551 regulator-max-microvolt = <880000>;
552 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
560 zap-shader {
561 firmware-name = "qcom/x1e80100/LENOVO/21N1/qcdxkmsuc8380.mbn";
566 clock-frequency = <400000>;
568 pinctrl-0 = <&qup_i2c0_data_clk>, <&tpad_default>;
569 pinctrl-names = "default";
575 compatible = "hid-over-i2c";
578 hid-descr-addr = <0x1>;
579 interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
581 wakeup-source;
586 compatible = "hid-over-i2c";
589 hid-descr-addr = <0x20>;
590 interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
592 wakeup-source;
597 compatible = "hid-over-i2c";
600 hid-descr-addr = <0x1>;
601 interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
603 pinctrl-0 = <&kybd_default>;
604 pinctrl-names = "default";
606 wakeup-source;
611 clock-frequency = <400000>;
618 #phy-cells = <0>;
620 vdd3v3-supply = <&vreg_l13b_3p0>;
621 vdd1v8-supply = <&vreg_l4b_1p8>;
623 reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
625 pinctrl-0 = <&eusb5_reset_n>;
626 pinctrl-names = "default";
632 #phy-cells = <0>;
634 vdd3v3-supply = <&vreg_l13b_3p0>;
635 vdd1v8-supply = <&vreg_l4b_1p8>;
637 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
639 pinctrl-0 = <&eusb3_reset_n>;
640 pinctrl-names = "default";
646 #phy-cells = <0>;
648 vdd3v3-supply = <&vreg_l13b_3p0>;
649 vdd1v8-supply = <&vreg_l4b_1p8>;
651 reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
653 pinctrl-0 = <&eusb6_reset_n>;
654 pinctrl-names = "default";
659 clock-frequency = <400000>;
665 compatible = "hid-over-i2c";
668 hid-descr-addr = <0x1>;
669 interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
671 pinctrl-0 = <&ts0_default>;
672 pinctrl-names = "default";
675 /* TODO: second-sourced touchscreen @ 0x41 */
679 spkr_01_sd_n_active: spkr-01-sd-n-active-state {
680 pins = "gpio12";
682 drive-strength = <16>;
683 bias-disable;
684 output-low;
689 pinctrl-0 = <&dmic01_default>;
690 pinctrl-names = "default";
692 vdd-micb-supply = <&vreg_l1b_1p8>;
693 qcom,dmic-sample-rate = <4800000>;
701 compatible = "qcom,x1e80100-dp";
702 /delete-property/ #sound-dai-cells;
706 aux-bus {
708 compatible = "edp-panel";
709 enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
710 power-supply = <&vreg_edp_3p3>;
712 pinctrl-0 = <&edp_bl_en>;
713 pinctrl-names = "default";
717 remote-endpoint = <&mdss_dp3_out>;
728 data-lanes = <0 1 2 3>;
729 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
731 remote-endpoint = <&edp_panel_in>;
738 vdda-phy-supply = <&vreg_l3j_0p8>;
739 vdda-pll-supply = <&vreg_l2j_1p2>;
745 perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
746 wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
748 pinctrl-0 = <&pcie4_default>;
749 pinctrl-names = "default";
755 vdda-phy-supply = <&vreg_l3i_0p8>;
756 vdda-pll-supply = <&vreg_l3e_1p2>;
762 perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
763 wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
765 vddpe-3v3-supply = <&vreg_nvme>;
767 pinctrl-0 = <&pcie6a_default>;
768 pinctrl-names = "default";
774 vdda-phy-supply = <&vreg_l1d_0p8>;
775 vdda-pll-supply = <&vreg_l2j_1p2>;
781 edp_bl_en: edp-bl-en-state {
782 pins = "gpio4";
784 power-source = <1>;
785 input-disable;
786 output-enable;
803 firmware-name = "qcom/x1e80100/LENOVO/21N1/qcadsp8380.mbn",
810 firmware-name = "qcom/x1e80100/LENOVO/21N1/qccdsp8380.mbn",
821 vdd18-supply = <&vreg_l3d_1p8>;
822 vdd3-supply = <&vreg_l2b_3p0>;
830 vdd18-supply = <&vreg_l3d_1p8>;
831 vdd3-supply = <&vreg_l14b_3p0>;
837 pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
838 pinctrl-names = "default";
844 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
845 #sound-dai-cells = <0>;
846 sound-name-prefix = "SpkrLeft";
847 vdd-1p8-supply = <&vreg_l15b_1p8>;
848 vdd-io-supply = <&vreg_l12b_1p2>;
849 qcom,port-mapping = <1 2 3 7 10 13>;
856 reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
857 #sound-dai-cells = <0>;
858 sound-name-prefix = "SpkrRight";
859 vdd-1p8-supply = <&vreg_l15b_1p8>;
860 vdd-io-supply = <&vreg_l12b_1p2>;
861 qcom,port-mapping = <4 5 6 7 11 13>;
872 qcom,rx-port-mapping = <1 2 3 4 5>;
883 qcom,tx-port-mapping = <2 2 3 4>;
888 gpio-reserved-ranges = <34 2>, /* Unused */
893 eusb3_reset_n: eusb3-reset-n-state {
894 pins = "gpio6";
896 drive-strength = <2>;
897 bias-disable;
898 output-low;
901 eusb5_reset_n: eusb5-reset-n-state {
902 pins = "gpio7";
904 drive-strength = <2>;
905 bias-disable;
906 output-low;
909 eusb6_reset_n: eusb6-reset-n-state {
910 pins = "gpio184";
912 drive-strength = <2>;
913 bias-disable;
914 output-low;
917 tpad_default: tpad-default-state {
918 pins = "gpio3";
920 bias-pull-up;
923 nvme_reg_en: nvme-reg-en-state {
924 pins = "gpio18";
926 drive-strength = <2>;
927 bias-disable;
930 ts0_default: ts0-default-state {
931 reset-n-pins {
932 pins = "gpio48";
934 output-high;
935 drive-strength = <16>;
938 int-n-pins {
939 pins = "gpio51";
941 bias-disable;
945 kybd_default: kybd-default-state {
946 pins = "gpio67";
948 bias-disable;
951 edp_reg_en: edp-reg-en-state {
952 pins = "gpio70";
954 drive-strength = <16>;
955 bias-disable;
958 hall_int_n_default: hall-int-n-state {
959 pins = "gpio92";
961 bias-disable;
964 pcie4_default: pcie4-default-state {
965 clkreq-n-pins {
966 pins = "gpio147";
968 drive-strength = <2>;
969 bias-pull-up;
972 perst-n-pins {
973 pins = "gpio146";
975 drive-strength = <2>;
976 bias-disable;
979 wake-n-pins {
980 pins = "gpio148";
982 drive-strength = <2>;
983 bias-pull-up;
987 pcie6a_default: pcie6a-default-state {
988 clkreq-n-pins {
989 pins = "gpio153";
991 drive-strength = <2>;
992 bias-pull-up;
995 perst-n-pins {
996 pins = "gpio152";
998 drive-strength = <2>;
999 bias-disable;
1002 wake-n-pins {
1003 pins = "gpio154";
1005 drive-strength = <2>;
1006 bias-pull-up;
1010 wcd_default: wcd-reset-n-active-state {
1011 pins = "gpio191";
1013 drive-strength = <16>;
1014 bias-disable;
1015 output-low;
1020 vdd-supply = <&vreg_l3j_0p8>;
1021 vdda12-supply = <&vreg_l2j_1p2>;
1029 vdda-phy-supply = <&vreg_l2j_1p2>;
1030 vdda-pll-supply = <&vreg_l1j_0p8>;
1044 remote-endpoint = <&pmic_glink_ss0_hs_in>;
1048 remote-endpoint = <&pmic_glink_ss0_ss_in>;
1052 vdd-supply = <&vreg_l3j_0p8>;
1053 vdda12-supply = <&vreg_l2j_1p2>;
1061 vdda-phy-supply = <&vreg_l2j_1p2>;
1062 vdda-pll-supply = <&vreg_l2d_0p9>;
1076 remote-endpoint = <&pmic_glink_ss1_hs_in>;
1080 remote-endpoint = <&pmic_glink_ss1_ss_in>;
1092 vdd-supply = <&vreg_l2e_0p8>;
1093 vdda12-supply = <&vreg_l3e_1p2>;
1105 vdd-supply = <&vreg_l2e_0p8>;
1106 vdda12-supply = <&vreg_l3e_1p2>;
1114 vdd-supply = <&vreg_l2e_0p8>;
1115 vdda12-supply = <&vreg_l3e_1p2>;
1123 vdda-phy-supply = <&vreg_l3e_1p2>;
1124 vdda-pll-supply = <&vreg_l3c_0p8>;
1130 vdda-phy-supply = <&vreg_l3e_1p2>;
1131 vdda-pll-supply = <&vreg_l3c_0p8>;