Lines Matching +full:v +full:- +full:amic1 +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/leds/common.h>
9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
21 compatible = "qcom,sm8650-hdk", "qcom,sm8650";
22 chassis-type = "embedded";
30 stdout-path = "serial0:115200n8";
33 hdmi-out {
34 compatible = "hdmi-connector";
39 remote-endpoint = <<9611_out>;
44 gpio-keys {
45 compatible = "gpio-keys";
47 pinctrl-0 = <&volume_up_n>;
48 pinctrl-names = "default";
50 key-volume-up {
54 debounce-interval = <15>;
55 linux,can-disable;
56 wakeup-source;
61 compatible = "gpio-leds";
63 led-0 {
67 linux,default-trigger = "bluetooth-power";
68 default-state = "off";
71 led-1 {
75 default-state = "off";
76 panic-indicator;
79 led-2 {
83 linux,default-trigger = "phy0tx";
84 default-state = "off";
88 pmic-glink {
89 compatible = "qcom,sm8650-pmic-glink",
90 "qcom,sm8550-pmic-glink",
91 "qcom,pmic-glink";
92 #address-cells = <1>;
93 #size-cells = <0>;
94 orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
97 compatible = "usb-c-connector";
100 power-role = "dual";
101 data-role = "dual";
104 #address-cells = <1>;
105 #size-cells = <0>;
111 remote-endpoint = <&usb_1_dwc3_hs>;
119 remote-endpoint = <&usb_dp_qmpphy_out>;
127 remote-endpoint = <&wcd_usbss_sbu_mux>;
134 lt9611_1v2: regulator-lt9611-1v2 {
135 compatible = "regulator-fixed";
137 regulator-name = "LT9611_1V2";
138 regulator-min-microvolt = <1200000>;
139 regulator-max-microvolt = <1200000>;
141 vin-supply = <&vph_pwr>;
144 enable-active-high;
147 lt9611_3v3: regulator-lt9611-3v3 {
148 compatible = "regulator-fixed";
150 regulator-name = "LT9611_3V3";
151 regulator-min-microvolt = <3300000>;
152 regulator-max-microvolt = <3300000>;
154 vin-supply = <&vreg_bob_3v3>;
157 enable-active-high;
161 compatible = "qcom,sm8650-sndcard", "qcom,sm8450-sndcard";
162 model = "SM8650-HDK";
163 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
167 "AMIC1", "MIC BIAS1",
174 wcd-playback-dai-link {
175 link-name = "WCD Playback";
178 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
182 sound-dai = <&wcd939x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
186 sound-dai = <&q6apm>;
190 wcd-capture-dai-link {
191 link-name = "WCD Capture";
194 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
198 sound-dai = <&wcd939x 1>, <&swr2 0>, <&lpass_txmacro 0>;
202 sound-dai = <&q6apm>;
206 wsa-dai-link {
207 link-name = "WSA Playback";
210 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
214 sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
218 sound-dai = <&q6apm>;
223 vph_pwr: regulator-vph-pwr {
224 compatible = "regulator-fixed";
226 regulator-name = "vph_pwr";
227 regulator-min-microvolt = <3700000>;
228 regulator-max-microvolt = <3700000>;
230 regulator-always-on;
231 regulator-boot-on;
234 vreg_bob_3v3: regulator-vreg-bob-3v3 {
235 compatible = "regulator-fixed";
237 regulator-name = "VREG_BOB_3P3";
238 regulator-min-microvolt = <3300000>;
239 regulator-max-microvolt = <3300000>;
241 vin-supply = <&vph_pwr>;
244 wcd939x: audio-codec {
245 compatible = "qcom,wcd9395-codec", "qcom,wcd9390-codec";
247 pinctrl-0 = <&wcd_default>;
248 pinctrl-names = "default";
250 qcom,micbias1-microvolt = <1800000>;
251 qcom,micbias2-microvolt = <1800000>;
252 qcom,micbias3-microvolt = <1800000>;
253 qcom,micbias4-microvolt = <1800000>;
254 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
255 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
256 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
257 qcom,rx-device = <&wcd_rx>;
258 qcom,tx-device = <&wcd_tx>;
260 reset-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
262 vdd-buck-supply = <&vreg_l15b_1p8>;
263 vdd-rxtx-supply = <&vreg_l15b_1p8>;
264 vdd-io-supply = <&vreg_l15b_1p8>;
265 vdd-mic-bias-supply = <&vreg_bob1>;
267 #sound-dai-cells = <1>;
270 wcn7850-pmu {
271 compatible = "qcom,wcn7850-pmu";
273 pinctrl-names = "default";
274 pinctrl-0 = <&wlan_en>, <&bt_default>;
276 wlan-enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
277 bt-enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
279 vdd-supply = <&vreg_s4i_0p85>;
280 vddio-supply = <&vreg_l15b_1p8>;
281 vddio1p2-supply = <&vreg_l3c_1p2>;
282 vddaon-supply = <&vreg_s2c_0p8>;
283 vdddig-supply = <&vreg_s3c_0p9>;
284 vddrfa1p2-supply = <&vreg_s1c_1p2>;
285 vddrfa1p8-supply = <&vreg_s6c_1p8>;
291 regulator-name = "vreg_pmu_rfa_cmn";
295 regulator-name = "vreg_pmu_aon_0p59";
299 regulator-name = "vreg_pmu_wlcx_0p8";
303 regulator-name = "vreg_pmu_wlmx_0p85";
307 regulator-name = "vreg_pmu_btcmx_0p85";
311 regulator-name = "vreg_pmu_rfa_0p8";
315 regulator-name = "vreg_pmu_rfa_1p2";
319 regulator-name = "vreg_pmu_rfa_1p8";
323 regulator-name = "vreg_pmu_pcie_0p9";
327 regulator-name = "vreg_pmu_pcie_1p8";
334 regulators-0 {
335 compatible = "qcom,pm8550-rpmh-regulators";
337 vdd-bob1-supply = <&vph_pwr>;
338 vdd-bob2-supply = <&vph_pwr>;
339 vdd-l2-l13-l14-supply = <&vreg_bob1>;
340 vdd-l3-supply = <&vreg_s1c_1p2>;
341 vdd-l5-l16-supply = <&vreg_bob1>;
342 vdd-l6-l7-supply = <&vreg_bob1>;
343 vdd-l8-l9-supply = <&vreg_bob1>;
344 vdd-l11-supply = <&vreg_s1c_1p2>;
345 vdd-l12-supply = <&vreg_s6c_1p8>;
346 vdd-l15-supply = <&vreg_s6c_1p8>;
347 vdd-l17-supply = <&vreg_bob2>;
349 qcom,pmic-id = "b";
352 regulator-name = "vreg_bob1";
353 regulator-min-microvolt = <3296000>;
354 regulator-max-microvolt = <3960000>;
355 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
359 regulator-name = "vreg_bob2";
360 regulator-min-microvolt = <2720000>;
361 regulator-max-microvolt = <3008000>;
362 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
366 regulator-name = "vreg_l2b_3p0";
367 regulator-min-microvolt = <3008000>;
368 regulator-max-microvolt = <3008000>;
369 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
370 regulator-allow-set-load;
371 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
376 regulator-name = "vreg_l5b_3p1";
377 regulator-min-microvolt = <3104000>;
378 regulator-max-microvolt = <3104000>;
379 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
380 regulator-allow-set-load;
381 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
386 regulator-name = "vreg_l6b_1p8";
387 regulator-min-microvolt = <1800000>;
388 regulator-max-microvolt = <3008000>;
389 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
390 regulator-allow-set-load;
391 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
396 regulator-name = "vreg_l7b_1p8";
397 regulator-min-microvolt = <1800000>;
398 regulator-max-microvolt = <3008000>;
399 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
403 regulator-name = "vreg_l8b_1p8";
404 regulator-min-microvolt = <1800000>;
405 regulator-max-microvolt = <3008000>;
406 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
407 regulator-allow-set-load;
408 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
413 regulator-name = "vreg_l9b_2p9";
414 regulator-min-microvolt = <2960000>;
415 regulator-max-microvolt = <3008000>;
416 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
417 regulator-allow-set-load;
418 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
423 regulator-name = "vreg_l11b_1p2";
424 regulator-min-microvolt = <1200000>;
425 regulator-max-microvolt = <1504000>;
426 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
427 regulator-allow-set-load;
428 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
433 regulator-name = "vreg_l12b_1p8";
434 regulator-min-microvolt = <1800000>;
435 regulator-max-microvolt = <1800000>;
436 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
437 regulator-allow-set-load;
438 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
443 regulator-name = "vreg_l13b_3p0";
444 regulator-min-microvolt = <3000000>;
445 regulator-max-microvolt = <3000000>;
446 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
447 regulator-allow-set-load;
448 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
453 regulator-name = "vreg_l14b_3p2";
454 regulator-min-microvolt = <3200000>;
455 regulator-max-microvolt = <3200000>;
456 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
457 regulator-allow-set-load;
458 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
463 regulator-name = "vreg_l15b_1p8";
464 regulator-min-microvolt = <1800000>;
465 regulator-max-microvolt = <1800000>;
466 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
467 regulator-allow-set-load;
468 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
473 regulator-name = "vreg_l16b_2p8";
474 regulator-min-microvolt = <2800000>;
475 regulator-max-microvolt = <2800000>;
476 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
477 regulator-allow-set-load;
478 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
483 regulator-name = "vreg_l17b_2p5";
484 regulator-min-microvolt = <2504000>;
485 regulator-max-microvolt = <2504000>;
486 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
487 regulator-allow-set-load;
488 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
493 regulators-1 {
494 compatible = "qcom,pm8550vs-rpmh-regulators";
496 vdd-l1-supply = <&vreg_s1c_1p2>;
497 vdd-l2-supply = <&vreg_s1c_1p2>;
498 vdd-l3-supply = <&vreg_s1c_1p2>;
499 vdd-s1-supply = <&vph_pwr>;
500 vdd-s2-supply = <&vph_pwr>;
501 vdd-s3-supply = <&vph_pwr>;
502 vdd-s4-supply = <&vph_pwr>;
503 vdd-s5-supply = <&vph_pwr>;
504 vdd-s6-supply = <&vph_pwr>;
506 qcom,pmic-id = "c";
509 regulator-name = "vreg_s1c_1p2";
510 regulator-min-microvolt = <1256000>;
511 regulator-max-microvolt = <1348000>;
512 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
516 regulator-name = "vreg_s2c_0p8";
517 regulator-min-microvolt = <852000>;
518 regulator-max-microvolt = <1036000>;
519 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
523 regulator-name = "vreg_s3c_0p9";
524 regulator-min-microvolt = <976000>;
525 regulator-max-microvolt = <1064000>;
526 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
530 regulator-name = "vreg_s4c_1p2";
531 regulator-min-microvolt = <1224000>;
532 regulator-max-microvolt = <1280000>;
533 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
537 regulator-name = "vreg_s5c_0p7";
538 regulator-min-microvolt = <752000>;
539 regulator-max-microvolt = <900000>;
540 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
544 regulator-name = "vreg_s6c_1p8";
545 regulator-min-microvolt = <1856000>;
546 regulator-max-microvolt = <2000000>;
547 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
551 regulator-name = "vreg_l1c_1p2";
552 regulator-min-microvolt = <1200000>;
553 regulator-max-microvolt = <1200000>;
554 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
555 regulator-allow-set-load;
556 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
561 regulator-name = "vreg_l3c_1p2";
562 regulator-min-microvolt = <1200000>;
563 regulator-max-microvolt = <1200000>;
564 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
565 regulator-allow-set-load;
566 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
571 regulators-2 {
572 compatible = "qcom,pm8550vs-rpmh-regulators";
574 vdd-l1-supply = <&vreg_s3c_0p9>;
576 qcom,pmic-id = "d";
579 regulator-name = "vreg_l1d_0p88";
580 regulator-min-microvolt = <912000>;
581 regulator-max-microvolt = <920000>;
582 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
583 regulator-allow-set-load;
584 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
589 regulators-3 {
590 compatible = "qcom,pm8550vs-rpmh-regulators";
592 vdd-l3-supply = <&vreg_s3c_0p9>;
594 qcom,pmic-id = "e";
597 regulator-name = "vreg_l3e_0p9";
598 regulator-min-microvolt = <880000>;
599 regulator-max-microvolt = <920000>;
600 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
601 regulator-allow-set-load;
602 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
607 regulators-4 {
608 compatible = "qcom,pm8550vs-rpmh-regulators";
610 vdd-l1-supply = <&vreg_s3c_0p9>;
611 vdd-l3-supply = <&vreg_s3c_0p9>;
613 qcom,pmic-id = "g";
616 regulator-name = "vreg_l1g_0p91";
617 regulator-min-microvolt = <912000>;
618 regulator-max-microvolt = <920000>;
619 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
620 regulator-allow-set-load;
621 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
626 regulator-name = "vreg_l3g_0p91";
627 regulator-min-microvolt = <880000>;
628 regulator-max-microvolt = <912000>;
629 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
630 regulator-allow-set-load;
631 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
636 regulators-5 {
637 compatible = "qcom,pm8550ve-rpmh-regulators";
639 vdd-l1-supply = <&vreg_s3c_0p9>;
640 vdd-l2-supply = <&vreg_s3c_0p9>;
641 vdd-l3-supply = <&vreg_s1c_1p2>;
642 vdd-s4-supply = <&vph_pwr>;
644 qcom,pmic-id = "i";
647 regulator-name = "vreg_s4i_0p85";
648 regulator-min-microvolt = <852000>;
649 regulator-max-microvolt = <1004000>;
650 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
654 regulator-name = "vreg_l1i_0p88";
655 regulator-min-microvolt = <880000>;
656 regulator-max-microvolt = <912000>;
657 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
658 regulator-allow-set-load;
659 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
664 regulator-name = "vreg_l2i_0p88";
665 regulator-min-microvolt = <880000>;
666 regulator-max-microvolt = <912000>;
667 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
668 regulator-allow-set-load;
669 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
674 regulator-name = "vreg_l3i_0p91";
675 regulator-min-microvolt = <1200000>;
676 regulator-max-microvolt = <1200000>;
677 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
678 regulator-allow-set-load;
679 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
684 regulators-6 {
685 compatible = "qcom,pm8010-rpmh-regulators";
686 qcom,pmic-id = "m";
688 vdd-l1-l2-supply = <&vreg_s1c_1p2>;
689 vdd-l3-l4-supply = <&vreg_bob2>;
690 vdd-l5-supply = <&vreg_s6c_1p8>;
691 vdd-l6-supply = <&vreg_bob1>;
692 vdd-l7-supply = <&vreg_bob1>;
695 regulator-name = "vreg_l1m_1p1";
696 regulator-min-microvolt = <1104000>;
697 regulator-max-microvolt = <1104000>;
698 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
699 regulator-allow-set-load;
700 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
705 regulator-name = "vreg_l2m_1p056";
706 regulator-min-microvolt = <1056000>;
707 regulator-max-microvolt = <1056000>;
708 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
709 regulator-allow-set-load;
710 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
715 regulator-name = "vreg_l3m_2p8";
716 regulator-min-microvolt = <2800000>;
717 regulator-max-microvolt = <2800000>;
718 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
722 regulator-name = "vreg_l4m_2p8";
723 regulator-min-microvolt = <2800000>;
724 regulator-max-microvolt = <2800000>;
725 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
729 regulator-name = "vreg_l5m_1p8";
730 regulator-min-microvolt = <1800000>;
731 regulator-max-microvolt = <1800000>;
732 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
736 regulator-name = "vreg_l6m_2p8";
737 regulator-min-microvolt = <2800000>;
738 regulator-max-microvolt = <2800000>;
739 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
743 regulator-name = "vreg_l7m_2p96";
744 regulator-min-microvolt = <2960000>;
745 regulator-max-microvolt = <2960000>;
746 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
750 regulators-7 {
751 compatible = "qcom,pm8010-rpmh-regulators";
752 qcom,pmic-id = "n";
754 vdd-l1-l2-supply = <&vreg_s1c_1p2>;
755 vdd-l3-l4-supply = <&vreg_s6c_1p8>;
756 vdd-l5-supply = <&vreg_bob2>;
757 vdd-l6-supply = <&vreg_bob2>;
758 vdd-l7-supply = <&vreg_bob1>;
761 regulator-name = "vreg_l1n_1p1";
762 regulator-min-microvolt = <1104000>;
763 regulator-max-microvolt = <1104000>;
764 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
765 regulator-allow-set-load;
766 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
771 regulator-name = "vreg_l2n_1p056";
772 regulator-min-microvolt = <1056000>;
773 regulator-max-microvolt = <1056000>;
774 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
775 regulator-allow-set-load;
776 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
781 regulator-name = "vreg_l3n_1p8";
782 regulator-min-microvolt = <1800000>;
783 regulator-max-microvolt = <1800000>;
784 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
788 regulator-name = "vreg_l4n_1p8";
789 regulator-min-microvolt = <1800000>;
790 regulator-max-microvolt = <1800000>;
791 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
795 regulator-name = "vreg_l5n_2p8";
796 regulator-min-microvolt = <2800000>;
797 regulator-max-microvolt = <2800000>;
798 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
802 regulator-name = "vreg_l6n_2p8";
803 regulator-min-microvolt = <2800000>;
804 regulator-max-microvolt = <2800000>;
805 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
809 regulator-name = "vreg_l7n_3p3";
810 regulator-min-microvolt = <3304000>;
811 regulator-max-microvolt = <3304000>;
812 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
824 wcd_usbss: typec-mux@e {
825 compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
828 vdd-supply = <&vreg_l15b_1p8>;
829 reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
831 mode-switch;
832 orientation-switch;
835 #address-cells = <1>;
836 #size-cells = <0>;
842 remote-endpoint = <&pmic_glink_sbu>;
850 clock-frequency = <400000>;
853 lt9611_codec: hdmi-bridge@2b {
857 interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
859 reset-gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
861 vdd-supply = <<9611_1v2>;
862 vcc-supply = <<9611_3v3>;
864 pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>;
865 pinctrl-names = "default";
868 #address-cells = <1>;
869 #size-cells = <0>;
875 remote-endpoint = <&mdss_dsi0_out>;
883 remote-endpoint = <&hdmi_connector_out>;
891 qcom,gsi-loader = "self";
892 memory-region = <&ipa_fw_mem>;
893 firmware-name = "qcom/sm8650/ipa_fws.mbn";
900 zap-shader {
901 firmware-name = "qcom/sm8650/gen70900_zap.mbn";
906 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
909 drive-strength = <16>;
910 bias-disable;
911 output-low;
920 vdda-supply = <&vreg_l3i_1p2>;
926 remote-endpoint = <<9611_a>;
927 data-lanes = <0 1 2 3>;
931 vdds-supply = <&vreg_l1i_0p88>;
941 data-lanes = <0 1>;
945 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
946 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
948 pinctrl-0 = <&pcie0_default_state>;
949 pinctrl-names = "default";
959 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
960 vddaon-supply = <&vreg_pmu_aon_0p59>;
961 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
962 vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
963 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
964 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
965 vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
966 vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
967 vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
972 vdda-phy-supply = <&vreg_l1i_0p88>;
973 vdda-pll-supply = <&vreg_l3i_1p2>;
979 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
980 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
982 pinctrl-0 = <&pcie1_default_state>;
983 pinctrl-names = "default";
989 vdda-phy-supply = <&vreg_l3e_0p9>;
990 vdda-pll-supply = <&vreg_l3i_1p2>;
991 vdda-qref-supply = <&vreg_l1i_0p88>;
997 sdc2_card_det_n: sdc2-card-det-state {
1000 bias-pull-up;
1001 input-enable;
1002 output-disable;
1003 power-source = <1>; /* 1.8 V */
1006 volume_up_n: volume-up-n-state {
1009 bias-pull-up;
1010 input-enable;
1011 power-source = <1>;
1017 #address-cells = <1>;
1018 #size-cells = <0>;
1026 default-state = "off";
1033 default-state = "off";
1040 default-state = "off";
1045 vdd18-supply = <&vreg_l15b_1p8>;
1046 vdd3-supply = <&vreg_l5b_3p1>;
1064 /* Use internal I2C pull-up */
1065 bias-pull-up = <2200>;
1079 firmware-name = "qcom/sm8650/adsp.mbn",
1086 firmware-name = "qcom/sm8650/cdsp.mbn",
1093 firmware-name = "qcom/sm8650/modem.mbn",
1100 cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
1102 vmmc-supply = <&vreg_l9b_2p9>;
1103 vqmmc-supply = <&vreg_l8b_1p8>;
1104 bus-width = <4>;
1105 no-sdio;
1106 no-mmc;
1108 pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
1109 pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
1110 pinctrl-names = "default", "sleep";
1116 clock-frequency = <32000>;
1126 pinctrl-0 = <&spkr_1_sd_n_active>;
1127 pinctrl-names = "default";
1128 powerdown-gpios = <&lpass_tlmm 21 GPIO_ACTIVE_LOW>;
1129 #sound-dai-cells = <0>;
1130 sound-name-prefix = "SpkrLeft";
1131 vdd-1p8-supply = <&vreg_l15b_1p8>;
1132 vdd-io-supply = <&vreg_l3c_1p2>;
1142 qcom,port-mapping = <1 2 3 7 10 13>;
1149 pinctrl-0 = <&spkr_2_sd_n_active>;
1150 pinctrl-names = "default";
1151 powerdown-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
1152 #sound-dai-cells = <0>;
1153 sound-name-prefix = "SpkrRight";
1154 vdd-1p8-supply = <&vreg_l15b_1p8>;
1155 vdd-io-supply = <&vreg_l3c_1p2>;
1165 qcom,port-mapping = <4 5 6 7 11 13>;
1185 qcom,rx-port-mapping = <1 2 3 4 5 9>;
1203 qcom,tx-port-mapping = <2 2 3 4>;
1209 gpio-reserved-ranges = <32 8>, <74 1>;
1211 bt_default: bt-default-state {
1212 bt-en-pins {
1215 drive-strength = <16>;
1216 bias-disable;
1219 sw-ctrl-pins {
1222 bias-pull-down;
1226 lt9611_irq_pin: lt9611-irq-state {
1229 bias-disable;
1232 lt9611_rst_pin: lt9611-rst-state {
1235 output-high;
1238 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
1241 drive-strength = <16>;
1242 bias-disable;
1243 output-low;
1246 wcd_default: wcd-reset-n-active-state {
1249 drive-strength = <16>;
1250 bias-disable;
1251 output-low;
1254 wlan_en: wlan-en-state {
1257 drive-strength = <8>;
1258 bias-pull-down;
1266 compatible = "qcom,wcn7850-bt";
1268 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
1269 vddaon-supply = <&vreg_pmu_aon_0p59>;
1270 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
1271 vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
1272 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
1273 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
1274 vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
1276 max-speed = <3200000>;
1285 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1287 vcc-supply = <&vreg_l17b_2p5>;
1288 vcc-max-microamp = <1300000>;
1289 vccq-supply = <&vreg_l1c_1p2>;
1290 vccq-max-microamp = <1200000>;
1296 vdda-phy-supply = <&vreg_l1d_0p88>;
1297 vdda-pll-supply = <&vreg_l3i_1p2>;
1303 * DPAUX -> WCD9395 -> USB_SBU -> USB-C
1304 * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C
1305 * USB SS -> USB-C
1314 usb-role-switch;
1318 remote-endpoint = <&pmic_glink_hs_in>;
1322 vdd-supply = <&vreg_l1i_0p88>;
1323 vdda12-supply = <&vreg_l3i_1p2>;
1331 vdda-phy-supply = <&vreg_l3i_1p2>;
1332 vdda-pll-supply = <&vreg_l3g_0p91>;
1338 remote-endpoint = <&pmic_glink_ss_in>;
1342 clock-frequency = <76800000>;