Lines Matching +full:ldo2 +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
22 compatible = "qcom,sm8550-mtp", "qcom,sm8550";
23 chassis-type = "handset";
29 wcd938x: audio-codec {
30 compatible = "qcom,wcd9385-codec";
32 pinctrl-names = "default";
33 pinctrl-0 = <&wcd_default>;
35 qcom,micbias1-microvolt = <1800000>;
36 qcom,micbias2-microvolt = <1800000>;
37 qcom,micbias3-microvolt = <1800000>;
38 qcom,micbias4-microvolt = <1800000>;
39 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
40 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
41 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
42 qcom,rx-device = <&wcd_rx>;
43 qcom,tx-device = <&wcd_tx>;
45 reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
47 vdd-buck-supply = <&vreg_l15b_1p8>;
48 vdd-rxtx-supply = <&vreg_l15b_1p8>;
49 vdd-io-supply = <&vreg_l15b_1p8>;
50 vdd-mic-bias-supply = <&vreg_bob1>;
52 #sound-dai-cells = <1>;
56 stdout-path = "serial0:115200n8";
59 pmic-glink {
60 compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
61 #address-cells = <1>;
62 #size-cells = <0>;
63 orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
66 compatible = "usb-c-connector";
68 power-role = "dual";
69 data-role = "dual";
72 #address-cells = <1>;
73 #size-cells = <0>;
79 remote-endpoint = <&usb_1_dwc3_hs>;
87 remote-endpoint = <&usb_dp_qmpphy_out>;
95 remote-endpoint = <&fsa4480_sbu_mux>;
103 compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
104 model = "SM8550-MTP";
105 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
125 wcd-playback-dai-link {
126 link-name = "WCD Playback";
129 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
133 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
137 sound-dai = <&q6apm>;
141 wcd-capture-dai-link {
142 link-name = "WCD Capture";
145 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
149 sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
153 sound-dai = <&q6apm>;
157 wsa-dai-link {
158 link-name = "WSA Playback";
161 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
165 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
169 sound-dai = <&q6apm>;
173 va-dai-link {
174 link-name = "VA Capture";
177 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
181 sound-dai = <&lpass_vamacro 0>;
185 sound-dai = <&q6apm>;
190 vph_pwr: vph-pwr-regulator {
191 compatible = "regulator-fixed";
192 regulator-name = "vph_pwr";
193 regulator-min-microvolt = <3700000>;
194 regulator-max-microvolt = <3700000>;
196 regulator-always-on;
197 regulator-boot-on;
202 regulators-0 {
203 compatible = "qcom,pm8550-rpmh-regulators";
204 qcom,pmic-id = "b";
206 vdd-bob1-supply = <&vph_pwr>;
207 vdd-bob2-supply = <&vph_pwr>;
208 vdd-l1-l4-l10-supply = <&vreg_s6g_1p8>;
209 vdd-l2-l13-l14-supply = <&vreg_bob1>;
210 vdd-l3-supply = <&vreg_s4g_1p3>;
211 vdd-l5-l16-supply = <&vreg_bob1>;
212 vdd-l6-l7-supply = <&vreg_bob1>;
213 vdd-l8-l9-supply = <&vreg_bob1>;
214 vdd-l11-supply = <&vreg_s4g_1p3>;
215 vdd-l12-supply = <&vreg_s6g_1p8>;
216 vdd-l15-supply = <&vreg_s6g_1p8>;
217 vdd-l17-supply = <&vreg_bob2>;
220 regulator-name = "vreg_bob1";
221 regulator-min-microvolt = <3296000>;
222 regulator-max-microvolt = <3960000>;
223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
227 regulator-name = "vreg_bob2";
228 regulator-min-microvolt = <2720000>;
229 regulator-max-microvolt = <3960000>;
230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
234 regulator-name = "vreg_l1b_1p8";
235 regulator-min-microvolt = <1800000>;
236 regulator-max-microvolt = <1800000>;
237 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
240 vreg_l2b_3p0: ldo2 {
241 regulator-name = "vreg_l2b_3p0";
242 regulator-min-microvolt = <3008000>;
243 regulator-max-microvolt = <3008000>;
244 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
248 regulator-name = "vreg_l5b_3p1";
249 regulator-min-microvolt = <3104000>;
250 regulator-max-microvolt = <3104000>;
251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
255 regulator-name = "vreg_l6b_1p8";
256 regulator-min-microvolt = <1800000>;
257 regulator-max-microvolt = <3008000>;
258 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
262 regulator-name = "vreg_l7b_1p8";
263 regulator-min-microvolt = <1800000>;
264 regulator-max-microvolt = <3008000>;
265 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
269 regulator-name = "vreg_l8b_1p8";
270 regulator-min-microvolt = <1800000>;
271 regulator-max-microvolt = <3008000>;
272 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
276 regulator-name = "vreg_l9b_2p9";
277 regulator-min-microvolt = <2960000>;
278 regulator-max-microvolt = <3008000>;
279 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
283 regulator-name = "vreg_l11b_1p2";
284 regulator-min-microvolt = <1200000>;
285 regulator-max-microvolt = <1504000>;
286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
290 regulator-name = "vreg_l12b_1p8";
291 regulator-min-microvolt = <1800000>;
292 regulator-max-microvolt = <1800000>;
293 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
297 regulator-name = "vreg_l13b_3p0";
298 regulator-min-microvolt = <3000000>;
299 regulator-max-microvolt = <3000000>;
300 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
304 regulator-name = "vreg_l14b_3p2";
305 regulator-min-microvolt = <3200000>;
306 regulator-max-microvolt = <3200000>;
307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
311 regulator-name = "vreg_l15b_1p8";
312 regulator-min-microvolt = <1800000>;
313 regulator-max-microvolt = <1800000>;
314 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
318 regulator-name = "vreg_l16b_2p8";
319 regulator-min-microvolt = <2800000>;
320 regulator-max-microvolt = <2800000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
325 regulator-name = "vreg_l17b_2p5";
326 regulator-min-microvolt = <2504000>;
327 regulator-max-microvolt = <2504000>;
328 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
332 regulators-1 {
333 compatible = "qcom,pm8550vs-rpmh-regulators";
334 qcom,pmic-id = "c";
336 vdd-l3-supply = <&vreg_s4e_0p9>;
339 regulator-name = "vreg_l3c_0p9";
340 regulator-min-microvolt = <880000>;
341 regulator-max-microvolt = <912000>;
342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
346 regulators-2 {
347 compatible = "qcom,pm8550vs-rpmh-regulators";
348 qcom,pmic-id = "d";
350 vdd-l1-supply = <&vreg_s4e_0p9>;
353 regulator-name = "vreg_l1d_0p88";
354 regulator-min-microvolt = <880000>;
355 regulator-max-microvolt = <920000>;
356 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
360 regulators-3 {
361 compatible = "qcom,pm8550vs-rpmh-regulators";
362 qcom,pmic-id = "e";
364 vdd-l1-supply = <&vreg_s4e_0p9>;
365 vdd-l2-supply = <&vreg_s4e_0p9>;
366 vdd-l3-supply = <&vreg_s4g_1p3>;
367 vdd-s4-supply = <&vph_pwr>;
368 vdd-s5-supply = <&vph_pwr>;
371 regulator-name = "vreg_s4e_0p9";
372 regulator-min-microvolt = <904000>;
373 regulator-max-microvolt = <984000>;
374 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
378 regulator-name = "vreg_s5e_1p1";
379 regulator-min-microvolt = <1080000>;
380 regulator-max-microvolt = <1120000>;
381 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
385 regulator-name = "vreg_l1e_0p88";
386 regulator-min-microvolt = <880000>;
387 regulator-max-microvolt = <880000>;
388 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
391 vreg_l2e_0p9: ldo2 {
392 regulator-name = "vreg_l2e_0p9";
393 regulator-min-microvolt = <904000>;
394 regulator-max-microvolt = <970000>;
395 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
399 regulator-name = "vreg_l3e_1p2";
400 regulator-min-microvolt = <1200000>;
401 regulator-max-microvolt = <1200000>;
402 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
406 regulators-4 {
407 compatible = "qcom,pm8550ve-rpmh-regulators";
408 qcom,pmic-id = "f";
410 vdd-l1-supply = <&vreg_s4e_0p9>;
411 vdd-l2-supply = <&vreg_s4e_0p9>;
412 vdd-l3-supply = <&vreg_s4e_0p9>;
413 vdd-s4-supply = <&vph_pwr>;
416 regulator-name = "vreg_s4f_0p5";
417 regulator-min-microvolt = <500000>;
418 regulator-max-microvolt = <700000>;
419 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
423 regulator-name = "vreg_l1f_0p9";
424 regulator-min-microvolt = <912000>;
425 regulator-max-microvolt = <912000>;
426 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
429 vreg_l2f_0p88: ldo2 {
430 regulator-name = "vreg_l2f_0p88";
431 regulator-min-microvolt = <880000>;
432 regulator-max-microvolt = <912000>;
433 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
437 regulator-name = "vreg_l3f_0p91";
438 regulator-min-microvolt = <880000>;
439 regulator-max-microvolt = <912000>;
440 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
444 regulators-5 {
445 compatible = "qcom,pm8550vs-rpmh-regulators";
446 qcom,pmic-id = "g";
448 vdd-l1-supply = <&vreg_s4g_1p3>;
449 vdd-l2-supply = <&vreg_s4g_1p3>;
450 vdd-l3-supply = <&vreg_s4g_1p3>;
451 vdd-s1-supply = <&vph_pwr>;
452 vdd-s2-supply = <&vph_pwr>;
453 vdd-s3-supply = <&vph_pwr>;
454 vdd-s4-supply = <&vph_pwr>;
455 vdd-s5-supply = <&vph_pwr>;
456 vdd-s6-supply = <&vph_pwr>;
459 regulator-name = "vreg_s1g_1p2";
460 regulator-min-microvolt = <1200000>;
461 regulator-max-microvolt = <1300000>;
462 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
466 regulator-name = "vreg_s2g_0p8";
467 regulator-min-microvolt = <800000>;
468 regulator-max-microvolt = <1000000>;
469 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
473 regulator-name = "vreg_s3g_0p7";
474 regulator-min-microvolt = <300000>;
475 regulator-max-microvolt = <1004000>;
476 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
480 regulator-name = "vreg_s4g_1p3";
481 regulator-min-microvolt = <1200000>;
482 regulator-max-microvolt = <1352000>;
483 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
487 regulator-name = "vreg_s5g_0p8";
488 regulator-min-microvolt = <500000>;
489 regulator-max-microvolt = <1004000>;
490 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
494 regulator-name = "vreg_s6g_1p8";
495 regulator-min-microvolt = <1800000>;
496 regulator-max-microvolt = <2000000>;
497 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
501 regulator-name = "vreg_l1g_1p2";
502 regulator-min-microvolt = <1200000>;
503 regulator-max-microvolt = <1200000>;
504 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
507 vreg_l2g_1p2: ldo2 {
508 regulator-name = "vreg_l2g_1p2";
509 regulator-min-microvolt = <1200000>;
510 regulator-max-microvolt = <1200000>;
511 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
515 regulator-name = "vreg_l3g_1p2";
516 regulator-min-microvolt = <1200000>;
517 regulator-max-microvolt = <1200000>;
518 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
522 regulators-6 {
523 compatible = "qcom,pm8010-rpmh-regulators";
524 qcom,pmic-id = "m";
526 vdd-l1-l2-supply = <&vreg_s4g_1p3>;
527 vdd-l3-l4-supply = <&vreg_bob2>;
528 vdd-l5-supply = <&vreg_s6g_1p8>;
529 vdd-l6-supply = <&vreg_s6g_1p8>;
530 vdd-l7-supply = <&vreg_bob1>;
533 regulator-name = "vreg_l1m_1p056";
534 regulator-min-microvolt = <1056000>;
535 regulator-max-microvolt = <1056000>;
536 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
539 vreg_l2m_1p056: ldo2 {
540 regulator-name = "vreg_l2m_1p056";
541 regulator-min-microvolt = <1056000>;
542 regulator-max-microvolt = <1056000>;
543 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
547 regulator-name = "vreg_l3m_2p8";
548 regulator-min-microvolt = <2800000>;
549 regulator-max-microvolt = <2800000>;
550 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
554 regulator-name = "vreg_l4m_2p8";
555 regulator-min-microvolt = <2800000>;
556 regulator-max-microvolt = <2800000>;
557 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
561 regulator-name = "vreg_l5m_1p8";
562 regulator-min-microvolt = <1800000>;
563 regulator-max-microvolt = <1800000>;
564 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
568 regulator-name = "vreg_l6m_1p8";
569 regulator-min-microvolt = <1800000>;
570 regulator-max-microvolt = <1800000>;
571 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
575 regulator-name = "vreg_l7m_2p9";
576 regulator-min-microvolt = <2800000>;
577 regulator-max-microvolt = <2904000>;
578 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
582 regulators-7 {
583 compatible = "qcom,pm8010-rpmh-regulators";
584 qcom,pmic-id = "n";
586 vdd-l1-l2-supply = <&vreg_s4g_1p3>;
587 vdd-l3-l4-supply = <&vreg_bob2>;
588 vdd-l5-supply = <&vreg_s6g_1p8>;
589 vdd-l6-supply = <&vreg_bob1>;
590 vdd-l7-supply = <&vreg_bob1>;
593 regulator-name = "vreg_l1n_1p1";
594 regulator-min-microvolt = <1104000>;
595 regulator-max-microvolt = <1200000>;
596 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
599 vreg_l2n_1p1: ldo2 {
600 regulator-name = "vreg_l2n_1p1";
601 regulator-min-microvolt = <1104000>;
602 regulator-max-microvolt = <1200000>;
603 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
607 regulator-name = "vreg_l3n_2p8";
608 regulator-min-microvolt = <2800000>;
609 regulator-max-microvolt = <3000000>;
610 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
614 regulator-name = "vreg_l4n_2p8";
615 regulator-min-microvolt = <2800000>;
616 regulator-max-microvolt = <3300000>;
617 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
621 regulator-name = "vreg_l5n_1p8";
622 regulator-min-microvolt = <1800000>;
623 regulator-max-microvolt = <1800000>;
624 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
628 regulator-name = "vreg_l6n_3p3";
629 regulator-min-microvolt = <2800000>;
630 regulator-max-microvolt = <3304000>;
631 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
635 regulator-name = "vreg_l7n_2p96";
636 regulator-min-microvolt = <2800000>;
637 regulator-max-microvolt = <2960000>;
638 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
646 zap-shader {
647 firmware-name = "qcom/sm8550/a740_zap.mbn";
658 typec-mux@42 {
662 vcc-supply = <&vreg_bob1>;
664 mode-switch;
665 orientation-switch;
669 remote-endpoint = <&pmic_glink_sbu>;
676 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
679 drive-strength = <16>;
680 bias-disable;
681 output-low;
684 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
687 drive-strength = <16>;
688 bias-disable;
689 output-low;
698 vdda-supply = <&vreg_l3e_1p2>;
705 pinctrl-names = "default", "sleep";
706 pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
707 pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
709 vddio-supply = <&vreg_l12b_1p8>;
710 vci-supply = <&vreg_l13b_3p0>;
711 vdd-supply = <&vreg_l11b_1p2>;
713 reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
717 remote-endpoint = <&mdss_dsi0_out>;
724 remote-endpoint = <&panel0_in>;
725 data-lanes = <0 1 2 3>;
729 vdds-supply = <&vreg_l1e_0p88>;
738 data-lanes = <0 1>;
742 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
743 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
745 pinctrl-names = "default";
746 pinctrl-0 = <&pcie0_default_state>;
752 vdda-phy-supply = <&vreg_l1e_0p88>;
753 vdda-pll-supply = <&vreg_l3e_1p2>;
759 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
760 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
762 pinctrl-names = "default";
763 pinctrl-0 = <&pcie1_default_state>;
769 vdda-phy-supply = <&vreg_l3c_0p91>;
770 vdda-pll-supply = <&vreg_l3e_1p2>;
771 vdda-qref-supply = <&vreg_l1e_0p88>;
777 sdc2_card_det_n: sdc2-card-det-state {
780 input-enable;
781 output-disable;
782 bias-pull-up;
783 power-source = <1>; /* 1.8 V */
788 vdd18-supply = <&vreg_l15b_1p8>;
789 vdd3-supply = <&vreg_l5b_3p1>;
797 firmware-name = "qcom/sm8550/adsp.mbn",
803 firmware-name = "qcom/sm8550/cdsp.mbn",
809 firmware-name = "qcom/sm8550/modem.mbn",
815 cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
816 pinctrl-names = "default", "sleep";
817 pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
818 pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
819 vmmc-supply = <&vreg_l9b_2p9>;
820 vqmmc-supply = <&vreg_l8b_1p8>;
821 bus-width = <4>;
822 no-sdio;
823 no-mmc;
828 clock-frequency = <32000>;
838 pinctrl-names = "default";
839 pinctrl-0 = <&spkr_1_sd_n_active>;
840 powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>;
841 #sound-dai-cells = <0>;
842 sound-name-prefix = "SpkrLeft";
843 vdd-1p8-supply = <&vreg_l15b_1p8>;
844 vdd-io-supply = <&vreg_l3g_1p2>;
845 qcom,port-mapping = <1 2 3 7 10 13>;
852 pinctrl-names = "default";
853 pinctrl-0 = <&spkr_2_sd_n_active>;
854 powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>;
855 #sound-dai-cells = <0>;
856 sound-name-prefix = "SpkrRight";
857 vdd-1p8-supply = <&vreg_l15b_1p8>;
858 vdd-io-supply = <&vreg_l3g_1p2>;
859 qcom,port-mapping = <4 5 6 7 11 13>;
870 qcom,rx-port-mapping = <1 2 3 4 5>;
881 qcom,tx-port-mapping = <2 2 3 4>;
886 gpio-reserved-ranges = <32 8>;
888 sde_dsi_active: sde-dsi-active-state {
891 drive-strength = <8>;
892 bias-disable;
895 sde_dsi_suspend: sde-dsi-suspend-state {
898 drive-strength = <2>;
899 bias-pull-down;
902 sde_te_active: sde-te-active-state {
905 drive-strength = <2>;
906 bias-pull-down;
909 sde_te_suspend: sde-te-suspend-state {
912 drive-strength = <2>;
913 bias-pull-down;
916 wcd_default: wcd-reset-n-active-state {
919 drive-strength = <16>;
920 bias-disable;
921 output-low;
930 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
931 vcc-supply = <&vreg_l17b_2p5>;
932 vcc-max-microamp = <1300000>;
933 vccq-supply = <&vreg_l1g_1p2>;
934 vccq-max-microamp = <1200000>;
935 vdd-hba-supply = <&vreg_l3g_1p2>;
941 vdda-phy-supply = <&vreg_l1d_0p88>;
942 vdda-pll-supply = <&vreg_l3e_1p2>;
952 remote-endpoint = <&pmic_glink_hs_in>;
956 vdd-supply = <&vreg_l1e_0p88>;
957 vdda12-supply = <&vreg_l3e_1p2>;
965 vdda-phy-supply = <&vreg_l3e_1p2>;
966 vdda-pll-supply = <&vreg_l3f_0p91>;
972 remote-endpoint = <&pmic_glink_ss_in>;
976 clock-frequency = <76800000>;