Lines Matching +full:vdddig +full:- +full:supply
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/leds/common.h>
9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
22 compatible = "qcom,sm8550-hdk", "qcom,sm8550";
23 chassis-type = "embedded";
30 wcd938x: audio-codec {
31 compatible = "qcom,wcd9385-codec";
33 pinctrl-names = "default";
34 pinctrl-0 = <&wcd_default>;
36 qcom,micbias1-microvolt = <1800000>;
37 qcom,micbias2-microvolt = <1800000>;
38 qcom,micbias3-microvolt = <1800000>;
39 qcom,micbias4-microvolt = <1800000>;
40 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
41 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
42 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
43 qcom,rx-device = <&wcd_rx>;
44 qcom,tx-device = <&wcd_tx>;
46 reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
48 vdd-buck-supply = <&vreg_l15b_1p8>;
49 vdd-rxtx-supply = <&vreg_l15b_1p8>;
50 vdd-io-supply = <&vreg_l15b_1p8>;
51 vdd-mic-bias-supply = <&vreg_bob1>;
53 #sound-dai-cells = <1>;
57 stdout-path = "serial0:115200n8";
60 hdmi-out {
61 compatible = "hdmi-connector";
66 remote-endpoint = <<9611_out>;
71 gpio-keys {
72 compatible = "gpio-keys";
74 pinctrl-0 = <&volume_up_n>;
75 pinctrl-names = "default";
77 key-volume-up {
81 debounce-interval = <15>;
82 linux,can-disable;
83 wakeup-source;
88 compatible = "gpio-leds";
90 led-0 {
94 linux,default-trigger = "bluetooth-power";
95 default-state = "off";
98 led-1 {
102 default-state = "off";
103 panic-indicator;
106 led-2 {
110 linux,default-trigger = "phy0tx";
111 default-state = "off";
115 pmic-glink {
116 compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
117 #address-cells = <1>;
118 #size-cells = <0>;
119 orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
122 compatible = "usb-c-connector";
124 power-role = "dual";
125 data-role = "dual";
128 #address-cells = <1>;
129 #size-cells = <0>;
135 remote-endpoint = <&usb_1_dwc3_hs>;
143 remote-endpoint = <&usb_dp_qmpphy_out>;
151 remote-endpoint = <&fsa4480_sbu_mux>;
158 lt9611_1v2: regulator-lt9611-1v2 {
159 compatible = "regulator-fixed";
161 regulator-name = "LT9611_1V2";
162 regulator-min-microvolt = <1200000>;
163 regulator-max-microvolt = <1200000>;
165 vin-supply = <&vph_pwr>;
168 enable-active-high;
171 lt9611_3v3: regulator-lt9611-3v3 {
172 compatible = "regulator-fixed";
174 regulator-name = "LT9611_3V3";
175 regulator-min-microvolt = <3300000>;
176 regulator-max-microvolt = <3300000>;
178 vin-supply = <&vreg_bob_3v3>;
181 enable-active-high;
184 vph_pwr: regulator-vph-pwr {
185 compatible = "regulator-fixed";
187 regulator-name = "vph_pwr";
188 regulator-min-microvolt = <3700000>;
189 regulator-max-microvolt = <3700000>;
190 regulator-always-on;
191 regulator-boot-on;
194 vreg_bob_3v3: regulator-vreg-bob-3v3 {
195 compatible = "regulator-fixed";
197 regulator-name = "VREG_BOB_3P3";
198 regulator-min-microvolt = <3300000>;
199 regulator-max-microvolt = <3300000>;
201 vin-supply = <&vph_pwr>;
205 compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
206 model = "SM8550-HDK";
207 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
218 wcd-playback-dai-link {
219 link-name = "WCD Playback";
222 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
226 sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
230 sound-dai = <&q6apm>;
234 wcd-capture-dai-link {
235 link-name = "WCD Capture";
238 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
242 sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
246 sound-dai = <&q6apm>;
250 wsa-dai-link {
251 link-name = "WSA Playback";
254 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
258 sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
262 sound-dai = <&q6apm>;
266 va-dai-link {
267 link-name = "VA Capture";
270 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
274 sound-dai = <&lpass_vamacro 0>;
278 sound-dai = <&q6apm>;
283 wcn7850-pmu {
284 compatible = "qcom,wcn7850-pmu";
286 pinctrl-names = "default";
287 pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
289 wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
290 bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
292 vdd-supply = <&vreg_s5g_0p85>;
293 vddio-supply = <&vreg_l15b_1p8>;
294 vddaon-supply = <&vreg_s2g_0p85>;
295 vdddig-supply = <&vreg_s4e_0p95>;
296 vddrfa1p2-supply = <&vreg_s4g_1p25>;
297 vddrfa1p8-supply = <&vreg_s6g_1p86>;
301 regulator-name = "vreg_pmu_rfa_cmn";
305 regulator-name = "vreg_pmu_aon_0p59";
309 regulator-name = "vreg_pmu_wlcx_0p8";
313 regulator-name = "vreg_pmu_wlmx_0p85";
317 regulator-name = "vreg_pmu_btcmx_0p85";
321 regulator-name = "vreg_pmu_rfa_0p8";
325 regulator-name = "vreg_pmu_rfa_1p2";
329 regulator-name = "vreg_pmu_rfa_1p8";
333 regulator-name = "vreg_pmu_pcie_0p9";
337 regulator-name = "vreg_pmu_pcie_1p8";
344 regulators-0 {
345 compatible = "qcom,pm8550-rpmh-regulators";
347 vdd-bob1-supply = <&vph_pwr>;
348 vdd-bob2-supply = <&vph_pwr>;
349 vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
350 vdd-l2-l13-l14-supply = <&vreg_bob1>;
351 vdd-l3-supply = <&vreg_s4g_1p25>;
352 vdd-l5-l16-supply = <&vreg_bob1>;
353 vdd-l6-l7-supply = <&vreg_bob1>;
354 vdd-l8-l9-supply = <&vreg_bob1>;
355 vdd-l11-supply = <&vreg_s4g_1p25>;
356 vdd-l12-supply = <&vreg_s6g_1p86>;
357 vdd-l15-supply = <&vreg_s6g_1p86>;
358 vdd-l17-supply = <&vreg_bob2>;
360 qcom,pmic-id = "b";
363 regulator-name = "vreg_bob1";
364 regulator-min-microvolt = <3296000>;
365 regulator-max-microvolt = <3960000>;
366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
370 regulator-name = "vreg_bob2";
371 regulator-min-microvolt = <2720000>;
372 regulator-max-microvolt = <3960000>;
373 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
377 regulator-name = "vreg_l1b_1p8";
378 regulator-min-microvolt = <1800000>;
379 regulator-max-microvolt = <1800000>;
380 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
381 regulator-allow-set-load;
382 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
387 regulator-name = "vreg_l2b_3p0";
388 regulator-min-microvolt = <3008000>;
389 regulator-max-microvolt = <3008000>;
390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
391 regulator-allow-set-load;
392 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
397 regulator-name = "vreg_l5b_3p1";
398 regulator-min-microvolt = <3104000>;
399 regulator-max-microvolt = <3104000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
401 regulator-allow-set-load;
402 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
407 regulator-name = "vreg_l6b_1p8";
408 regulator-min-microvolt = <1800000>;
409 regulator-max-microvolt = <3008000>;
410 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
411 regulator-allow-set-load;
412 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
417 regulator-name = "vreg_l7b_1p8";
418 regulator-min-microvolt = <1800000>;
419 regulator-max-microvolt = <3008000>;
420 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
421 regulator-allow-set-load;
422 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
427 regulator-name = "vreg_l8b_1p8";
428 regulator-min-microvolt = <1800000>;
429 regulator-max-microvolt = <3008000>;
430 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
431 regulator-allow-set-load;
432 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
437 regulator-name = "vreg_l9b_2p9";
438 regulator-min-microvolt = <2960000>;
439 regulator-max-microvolt = <3008000>;
440 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
441 regulator-allow-set-load;
442 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
447 regulator-name = "vreg_l11b_1p2";
448 regulator-min-microvolt = <1200000>;
449 regulator-max-microvolt = <1504000>;
450 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
451 regulator-allow-set-load;
452 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
457 regulator-name = "vreg_l12b_1p8";
458 regulator-min-microvolt = <1800000>;
459 regulator-max-microvolt = <1800000>;
460 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
461 regulator-allow-set-load;
462 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
467 regulator-name = "vreg_l13b_3p0";
468 regulator-min-microvolt = <3000000>;
469 regulator-max-microvolt = <3000000>;
470 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
471 regulator-allow-set-load;
472 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
477 regulator-name = "vreg_l14b_3p2";
478 regulator-min-microvolt = <3200000>;
479 regulator-max-microvolt = <3200000>;
480 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
481 regulator-allow-set-load;
482 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
487 regulator-name = "vreg_l15b_1p8";
488 regulator-min-microvolt = <1800000>;
489 regulator-max-microvolt = <1800000>;
490 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
491 regulator-allow-set-load;
492 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
497 regulator-name = "vreg_l16b_2p8";
498 regulator-min-microvolt = <2800000>;
499 regulator-max-microvolt = <2800000>;
500 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
501 regulator-allow-set-load;
502 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
507 regulator-name = "vreg_l17b_2p5";
508 regulator-min-microvolt = <2504000>;
509 regulator-max-microvolt = <2504000>;
510 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
511 regulator-allow-set-load;
512 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
517 regulators-1 {
518 compatible = "qcom,pm8550vs-rpmh-regulators";
520 vdd-l1-supply = <&vreg_s4g_1p25>;
521 vdd-l2-supply = <&vreg_s4e_0p95>;
522 vdd-l3-supply = <&vreg_s4e_0p95>;
524 qcom,pmic-id = "c";
527 regulator-name = "vreg_l3c_0p9";
528 regulator-min-microvolt = <880000>;
529 regulator-max-microvolt = <912000>;
530 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
531 regulator-allow-set-load;
532 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
537 regulators-2 {
538 compatible = "qcom,pm8550vs-rpmh-regulators";
540 vdd-l1-supply = <&vreg_s4e_0p95>;
541 vdd-l2-supply = <&vreg_s4e_0p95>;
542 vdd-l3-supply = <&vreg_s4e_0p95>;
544 qcom,pmic-id = "d";
547 regulator-name = "vreg_l1d_0p88";
548 regulator-min-microvolt = <880000>;
549 regulator-max-microvolt = <920000>;
550 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
551 regulator-allow-set-load;
552 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
559 regulators-3 {
560 compatible = "qcom,pm8550vs-rpmh-regulators";
562 vdd-l1-supply = <&vreg_s4e_0p95>;
563 vdd-l2-supply = <&vreg_s4e_0p95>;
564 vdd-l3-supply = <&vreg_s4g_1p25>;
565 vdd-s4-supply = <&vph_pwr>;
566 vdd-s5-supply = <&vph_pwr>;
568 qcom,pmic-id = "e";
571 regulator-name = "vreg_s4e_0p95";
572 regulator-min-microvolt = <904000>;
573 regulator-max-microvolt = <984000>;
574 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
578 regulator-name = "vreg_s5e_1p08";
579 regulator-min-microvolt = <1080000>;
580 regulator-max-microvolt = <1120000>;
581 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
585 regulator-name = "vreg_l1e_0p88";
586 regulator-min-microvolt = <880000>;
587 regulator-max-microvolt = <880000>;
588 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
589 regulator-allow-set-load;
590 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
595 regulator-name = "vreg_l2e_0p9";
596 regulator-min-microvolt = <904000>;
597 regulator-max-microvolt = <970000>;
598 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
599 regulator-allow-set-load;
600 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
605 regulator-name = "vreg_l3e_1p2";
606 regulator-min-microvolt = <1200000>;
607 regulator-max-microvolt = <1200000>;
608 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
609 regulator-allow-set-load;
610 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
615 regulators-4 {
616 compatible = "qcom,pm8550ve-rpmh-regulators";
618 vdd-l1-supply = <&vreg_s4e_0p95>;
619 vdd-l2-supply = <&vreg_s4e_0p95>;
620 vdd-l3-supply = <&vreg_s4e_0p95>;
621 vdd-s4-supply = <&vph_pwr>;
623 qcom,pmic-id = "f";
626 regulator-name = "vreg_s4f_0p5";
627 regulator-min-microvolt = <500000>;
628 regulator-max-microvolt = <700000>;
629 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
633 regulator-name = "vreg_l1f_0p9";
634 regulator-min-microvolt = <912000>;
635 regulator-max-microvolt = <912000>;
636 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
637 regulator-allow-set-load;
638 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
643 regulator-name = "vreg_l2f_0p88";
644 regulator-min-microvolt = <880000>;
645 regulator-max-microvolt = <912000>;
646 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
647 regulator-allow-set-load;
648 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
653 regulator-name = "vreg_l3f_0p88";
654 regulator-min-microvolt = <880000>;
655 regulator-max-microvolt = <912000>;
656 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
657 regulator-allow-set-load;
658 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
663 regulators-5 {
664 compatible = "qcom,pm8550vs-rpmh-regulators";
666 vdd-l1-supply = <&vreg_s4g_1p25>;
667 vdd-l2-supply = <&vreg_s4g_1p25>;
668 vdd-l3-supply = <&vreg_s4g_1p25>;
669 vdd-s1-supply = <&vph_pwr>;
670 vdd-s2-supply = <&vph_pwr>;
671 vdd-s3-supply = <&vph_pwr>;
672 vdd-s4-supply = <&vph_pwr>;
673 vdd-s5-supply = <&vph_pwr>;
674 vdd-s6-supply = <&vph_pwr>;
676 qcom,pmic-id = "g";
679 regulator-name = "vreg_s1g_1p25";
680 regulator-min-microvolt = <1200000>;
681 regulator-max-microvolt = <1300000>;
682 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
686 regulator-name = "vreg_s2g_0p85";
687 regulator-min-microvolt = <800000>;
688 regulator-max-microvolt = <1000000>;
689 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
693 regulator-name = "vreg_s3g_0p8";
694 regulator-min-microvolt = <300000>;
695 regulator-max-microvolt = <1004000>;
696 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
700 regulator-name = "vreg_s4g_1p25";
701 regulator-min-microvolt = <1200000>;
702 regulator-max-microvolt = <1352000>;
703 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
707 regulator-name = "vreg_s5g_0p85";
708 regulator-min-microvolt = <500000>;
709 regulator-max-microvolt = <1004000>;
710 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
714 regulator-name = "vreg_s6g_1p86";
715 regulator-min-microvolt = <1800000>;
716 regulator-max-microvolt = <2000000>;
717 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
721 regulator-name = "vreg_l1g_1p2";
722 regulator-min-microvolt = <1200000>;
723 regulator-max-microvolt = <1200000>;
724 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
725 regulator-allow-set-load;
726 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
731 regulator-name = "vreg_l3g_1p2";
732 regulator-min-microvolt = <1200000>;
733 regulator-max-microvolt = <1200000>;
734 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
735 regulator-allow-set-load;
736 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
741 regulators-6 {
742 compatible = "qcom,pm8010-rpmh-regulators";
744 vdd-l1-l2-supply = <&vreg_s4g_1p25>;
745 vdd-l3-l4-supply = <&vreg_bob2>;
746 vdd-l5-supply = <&vreg_s6g_1p86>;
747 vdd-l6-supply = <&vreg_s6g_1p86>;
748 vdd-l7-supply = <&vreg_bob1>;
750 qcom,pmic-id = "m";
753 regulator-name = "vreg_l1m_1p056";
754 regulator-min-microvolt = <1056000>;
755 regulator-max-microvolt = <1056000>;
756 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
757 regulator-allow-set-load;
758 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
763 regulator-name = "vreg_l2m_1p056";
764 regulator-min-microvolt = <1056000>;
765 regulator-max-microvolt = <1056000>;
766 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
767 regulator-allow-set-load;
768 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
773 regulator-name = "vreg_l3m_2p8";
774 regulator-min-microvolt = <2800000>;
775 regulator-max-microvolt = <2800000>;
776 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
780 regulator-name = "vreg_l4m_2p8";
781 regulator-min-microvolt = <2800000>;
782 regulator-max-microvolt = <2800000>;
783 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
787 regulator-name = "vreg_l5m_1p8";
788 regulator-min-microvolt = <1800000>;
789 regulator-max-microvolt = <1800000>;
790 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
794 regulator-name = "vreg_l6m_1p8";
795 regulator-min-microvolt = <1800000>;
796 regulator-max-microvolt = <1800000>;
797 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
801 regulator-name = "vreg_l7m_2p9";
802 regulator-min-microvolt = <2800000>;
803 regulator-max-microvolt = <2904000>;
804 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
808 regulators-7 {
809 compatible = "qcom,pm8010-rpmh-regulators";
811 vdd-l1-l2-supply = <&vreg_s4g_1p25>;
812 vdd-l3-l4-supply = <&vreg_bob2>;
813 vdd-l5-supply = <&vreg_s6g_1p86>;
814 vdd-l6-supply = <&vreg_bob1>;
815 vdd-l7-supply = <&vreg_bob1>;
817 qcom,pmic-id = "n";
820 regulator-name = "vreg_l1n_1p1";
821 regulator-min-microvolt = <1104000>;
822 regulator-max-microvolt = <1200000>;
823 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
824 regulator-allow-set-load;
825 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
830 regulator-name = "vreg_l2n_1p1";
831 regulator-min-microvolt = <1104000>;
832 regulator-max-microvolt = <1200000>;
833 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
834 regulator-allow-set-load;
835 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
840 regulator-name = "vreg_l3n_2p8";
841 regulator-min-microvolt = <2800000>;
842 regulator-max-microvolt = <3000000>;
843 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
847 regulator-name = "vreg_l4n_2p8";
848 regulator-min-microvolt = <2800000>;
849 regulator-max-microvolt = <3300000>;
850 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
854 regulator-name = "vreg_l5n_1p8";
855 regulator-min-microvolt = <1800000>;
856 regulator-max-microvolt = <1800000>;
857 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
861 regulator-name = "vreg_l6n_3p3";
862 regulator-min-microvolt = <2800000>;
863 regulator-max-microvolt = <3304000>;
864 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
868 regulator-name = "vreg_l7n_2p96";
869 regulator-min-microvolt = <2800000>;
870 regulator-max-microvolt = <2960000>;
871 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
877 clock-frequency = <400000>;
880 lt9611_codec: hdmi-bridge@2b {
884 interrupts-extended = <&tlmm 8 IRQ_TYPE_EDGE_FALLING>;
886 reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
888 vdd-supply = <<9611_1v2>;
889 vcc-supply = <<9611_3v3>;
891 pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>;
892 pinctrl-names = "default";
895 #address-cells = <1>;
896 #size-cells = <0>;
902 remote-endpoint = <&mdss_dsi0_out>;
910 remote-endpoint = <&hdmi_connector_out>;
920 typec-mux@42 {
924 vcc-supply = <&vreg_bob1>;
926 mode-switch;
927 orientation-switch;
931 remote-endpoint = <&pmic_glink_sbu>;
942 qcom,gsi-loader = "self";
943 memory-region = <&ipa_fw_mem>;
944 firmware-name = "qcom/sm8550/ipa_fws.mbn";
955 zap-shader {
956 firmware-name = "qcom/sm8550/a740_zap.mbn";
961 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
964 drive-strength = <16>;
965 bias-disable;
966 output-low;
969 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
972 drive-strength = <16>;
973 bias-disable;
974 output-low;
983 vdda-supply = <&vreg_l3e_1p2>;
988 remote-endpoint = <<9611_a>;
989 data-lanes = <0 1 2 3>;
993 vdds-supply = <&vreg_l1e_0p88>;
1002 data-lanes = <0 1>;
1006 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
1007 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
1009 pinctrl-0 = <&pcie0_default_state>;
1010 pinctrl-names = "default";
1020 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
1021 vddaon-supply = <&vreg_pmu_aon_0p59>;
1022 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
1023 vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
1024 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
1025 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
1026 vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
1027 vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
1028 vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
1033 vdda-phy-supply = <&vreg_l1e_0p88>;
1034 vdda-pll-supply = <&vreg_l3e_1p2>;
1040 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
1041 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
1043 pinctrl-0 = <&pcie1_default_state>;
1044 pinctrl-names = "default";
1050 vdda-phy-supply = <&vreg_l3c_0p9>;
1051 vdda-pll-supply = <&vreg_l3e_1p2>;
1052 vdda-qref-supply = <&vreg_l1e_0p88>;
1058 sdc2_card_det_n: sdc2-card-det-state {
1061 input-enable;
1062 output-disable;
1063 bias-pull-up;
1064 power-source = <1>; /* 1.8 V */
1067 volume_up_n: volume-up-n-state {
1070 power-source = <1>;
1071 bias-pull-up;
1072 input-enable;
1078 #address-cells = <1>;
1079 #size-cells = <0>;
1087 default-state = "off";
1094 default-state = "off";
1101 default-state = "off";
1106 vdd18-supply = <&vreg_l15b_1p8>;
1107 vdd3-supply = <&vreg_l5b_3p1>;
1121 pmk8550_sleep_clk: sleep-clk-state {
1124 input-disable;
1125 output-enable;
1126 bias-disable;
1127 power-source = <0>;
1140 firmware-name = "qcom/sm8550/adsp.mbn",
1146 firmware-name = "qcom/sm8550/cdsp.mbn",
1152 firmware-name = "qcom/sm8550/modem.mbn",
1158 cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
1160 pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
1161 pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
1162 pinctrl-names = "default", "sleep";
1164 vmmc-supply = <&vreg_l9b_2p9>;
1165 vqmmc-supply = <&vreg_l8b_1p8>;
1167 bus-width = <4>;
1168 no-sdio;
1169 no-mmc;
1175 clock-frequency = <32000>;
1186 pinctrl-0 = <&spkr_1_sd_n_active>;
1187 pinctrl-names = "default";
1189 powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>;
1191 vdd-1p8-supply = <&vreg_l15b_1p8>;
1192 vdd-io-supply = <&vreg_l15b_1p8>;
1194 #sound-dai-cells = <0>;
1195 sound-name-prefix = "SpkrLeft";
1196 qcom,port-mapping = <1 2 3 7 10 13>;
1204 pinctrl-0 = <&spkr_2_sd_n_active>;
1205 pinctrl-names = "default";
1207 powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>;
1209 vdd-1p8-supply = <&vreg_l15b_1p8>;
1210 vdd-io-supply = <&vreg_l15b_1p8>;
1212 #sound-dai-cells = <0>;
1213 sound-name-prefix = "SpkrRight";
1214 qcom,port-mapping = <4 5 6 7 11 13>;
1233 qcom,rx-port-mapping = <1 2 3 4 5>;
1251 qcom,tx-port-mapping = <2 2 3 4>;
1257 gpio-reserved-ranges = <32 8>;
1259 bt_default: bt-default-state {
1260 bt-en-pins {
1263 drive-strength = <16>;
1264 bias-disable;
1267 sw-ctrl-pins {
1270 bias-pull-down;
1274 lt9611_irq_pin: lt9611-irq-state {
1277 bias-disable;
1280 lt9611_rst_pin: lt9611-rst-state {
1283 output-high;
1286 wcd_default: wcd-reset-n-active-state {
1289 drive-strength = <16>;
1290 bias-disable;
1291 output-low;
1294 wlan_en: wlan-en-state {
1297 drive-strength = <8>;
1298 bias-pull-down;
1310 compatible = "qcom,wcn7850-bt";
1312 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
1313 vddaon-supply = <&vreg_pmu_aon_0p59>;
1314 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
1315 vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
1316 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
1317 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
1318 vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
1320 max-speed = <3200000>;
1325 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1327 vcc-supply = <&vreg_l17b_2p5>;
1328 vcc-max-microamp = <1300000>;
1329 vccq-supply = <&vreg_l1g_1p2>;
1330 vccq-max-microamp = <1200000>;
1331 vdd-hba-supply = <&vreg_l3g_1p2>;
1337 vdda-phy-supply = <&vreg_l1d_0p88>;
1338 vdda-pll-supply = <&vreg_l3e_1p2>;
1348 remote-endpoint = <&pmic_glink_hs_in>;
1352 vdd-supply = <&vreg_l1e_0p88>;
1353 vdda12-supply = <&vreg_l3e_1p2>;
1361 vdda-phy-supply = <&vreg_l3e_1p2>;
1362 vdda-pll-supply = <&vreg_l3f_0p88>;
1368 remote-endpoint = <&pmic_glink_ss_in>;
1372 clock-frequency = <76800000>;