Lines Matching +full:vdd +full:- +full:io
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
9 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
10 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
11 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
12 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
13 #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
24 compatible = "qcom,sm8450-hdk", "qcom,sm8450";
25 chassis-type = "embedded";
31 wcd938x: audio-codec {
32 compatible = "qcom,wcd9385-codec";
34 pinctrl-names = "default";
35 pinctrl-0 = <&wcd_default>;
37 qcom,micbias1-microvolt = <1800000>;
38 qcom,micbias2-microvolt = <1800000>;
39 qcom,micbias3-microvolt = <1800000>;
40 qcom,micbias4-microvolt = <1800000>;
41 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
42 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
43 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
44 qcom,rx-device = <&wcd_rx>;
45 qcom,tx-device = <&wcd_tx>;
47 reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
49 vdd-buck-supply = <&vreg_s10b_1p8>;
50 vdd-rxtx-supply = <&vreg_s10b_1p8>;
51 vdd-io-supply = <&vreg_s10b_1p8>;
52 vdd-mic-bias-supply = <&vreg_bob>;
54 #sound-dai-cells = <1>;
58 stdout-path = "serial0:115200n8";
61 hdmi-out {
62 compatible = "hdmi-connector";
67 remote-endpoint = <<9611_out>;
72 lt9611_1v2: lt9611-vdd12-regulator {
73 compatible = "regulator-fixed";
74 regulator-name = "LT9611_1V2";
76 vin-supply = <&vph_pwr>;
77 regulator-min-microvolt = <1200000>;
78 regulator-max-microvolt = <1200000>;
80 enable-active-high;
83 lt9611_3v3: lt9611-3v3-regulator {
84 compatible = "regulator-fixed";
85 regulator-name = "LT9611_3V3";
87 vin-supply = <&vreg_bob>;
89 regulator-min-microvolt = <3300000>;
90 regulator-max-microvolt = <3300000>;
91 enable-active-high;
94 pmic-glink {
95 compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
96 #address-cells = <1>;
97 #size-cells = <0>;
98 orientation-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
101 compatible = "usb-c-connector";
103 power-role = "dual";
104 data-role = "dual";
107 #address-cells = <1>;
108 #size-cells = <0>;
114 remote-endpoint = <&usb_1_dwc3_hs>;
122 remote-endpoint = <&usb_1_qmpphy_out>;
130 remote-endpoint = <&fsa4480_sbu_mux>;
138 thermal-zones {
139 camera-thermal {
140 polling-delay-passive = <250>;
142 thermal-sensors = <&pmk8350_adc_tm 2>;
145 active-config0 {
153 rear-tof-thermal {
154 polling-delay-passive = <250>;
156 thermal-sensors = <&pmk8350_adc_tm 5>;
159 active-config0 {
167 skin-msm-thermal {
168 polling-delay-passive = <250>;
170 thermal-sensors = <&pmk8350_adc_tm 1>;
173 active-config0 {
181 therm1-thermal {
182 polling-delay-passive = <250>;
184 thermal-sensors = <&pmk8350_adc_tm 3>;
187 active-config0 {
195 therm2-thermal {
196 polling-delay-passive = <250>;
198 thermal-sensors = <&pmk8350_adc_tm 6>;
201 active-config0 {
209 usb-conn-thermal {
210 polling-delay-passive = <250>;
212 thermal-sensors = <&pmk8350_adc_tm 7>;
215 active-config0 {
223 wide-rfc-thermal {
224 polling-delay-passive = <250>;
226 thermal-sensors = <&pmk8350_adc_tm 4>;
229 active-config0 {
237 xo-thermal {
238 thermal-sensors = <&pmk8350_adc_tm 0>;
241 active-config0 {
250 vph_pwr: vph-pwr-regulator {
251 compatible = "regulator-fixed";
252 regulator-name = "vph_pwr";
253 regulator-min-microvolt = <3700000>;
254 regulator-max-microvolt = <3700000>;
256 regulator-always-on;
257 regulator-boot-on;
262 regulators-0 {
263 compatible = "qcom,pm8350-rpmh-regulators";
264 qcom,pmic-id = "b";
266 vdd-s1-supply = <&vph_pwr>;
267 vdd-s2-supply = <&vph_pwr>;
268 vdd-s3-supply = <&vph_pwr>;
269 vdd-s4-supply = <&vph_pwr>;
270 vdd-s5-supply = <&vph_pwr>;
271 vdd-s6-supply = <&vph_pwr>;
272 vdd-s7-supply = <&vph_pwr>;
273 vdd-s8-supply = <&vph_pwr>;
274 vdd-s9-supply = <&vph_pwr>;
275 vdd-s10-supply = <&vph_pwr>;
276 vdd-s11-supply = <&vph_pwr>;
277 vdd-s12-supply = <&vph_pwr>;
279 vdd-l1-l4-supply = <&vreg_s11b_0p95>;
280 vdd-l2-l7-supply = <&vreg_bob>;
281 vdd-l3-l5-supply = <&vreg_bob>;
282 vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
283 vdd-l8-supply = <&vreg_s2h_0p95>;
286 regulator-name = "vreg_s10b_1p8";
287 regulator-min-microvolt = <1800000>;
288 regulator-max-microvolt = <1800000>;
292 regulator-name = "vreg_s11b_0p95";
293 regulator-min-microvolt = <966000>;
294 regulator-max-microvolt = <1104000>;
298 regulator-name = "vreg_s12b_1p25";
299 regulator-min-microvolt = <1350000>;
300 regulator-max-microvolt = <1400000>;
304 regulator-name = "vreg_l1b_0p91";
305 regulator-min-microvolt = <912000>;
306 regulator-max-microvolt = <920000>;
307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
311 regulator-name = "vreg_l2b_3p07";
312 regulator-min-microvolt = <3072000>;
313 regulator-max-microvolt = <3072000>;
314 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
318 regulator-name = "vreg_l3b_0p9";
319 regulator-min-microvolt = <904000>;
320 regulator-max-microvolt = <904000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
325 regulator-name = "vreg_l5b_0p88";
326 regulator-min-microvolt = <880000>;
327 regulator-max-microvolt = <888000>;
328 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
332 regulator-name = "vreg_l6b_1p2";
333 regulator-min-microvolt = <1200000>;
334 regulator-max-microvolt = <1200000>;
335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
339 regulator-name = "vreg_l7b_2p5";
340 regulator-min-microvolt = <2504000>;
341 regulator-max-microvolt = <2504000>;
342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
346 regulator-name = "vreg_l9b_1p2";
347 regulator-min-microvolt = <1200000>;
348 regulator-max-microvolt = <1200000>;
349 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
353 regulators-1 {
354 compatible = "qcom,pm8350c-rpmh-regulators";
355 qcom,pmic-id = "c";
357 vdd-s1-supply = <&vph_pwr>;
358 vdd-s2-supply = <&vph_pwr>;
359 vdd-s3-supply = <&vph_pwr>;
360 vdd-s4-supply = <&vph_pwr>;
361 vdd-s5-supply = <&vph_pwr>;
362 vdd-s6-supply = <&vph_pwr>;
363 vdd-s7-supply = <&vph_pwr>;
364 vdd-s8-supply = <&vph_pwr>;
365 vdd-s9-supply = <&vph_pwr>;
366 vdd-s10-supply = <&vph_pwr>;
368 vdd-l1-l12-supply = <&vreg_bob>;
369 vdd-l2-l8-supply = <&vreg_bob>;
370 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
371 vdd-l6-l9-l11-supply = <&vreg_bob>;
372 vdd-l10-supply = <&vreg_s12b_1p25>;
374 vdd-bob-supply = <&vph_pwr>;
377 regulator-name = "vreg_s1c_1p86";
378 regulator-min-microvolt = <1800000>;
379 regulator-max-microvolt = <2024000>;
383 regulator-name = "vreg_s10c_1p05";
384 regulator-min-microvolt = <1000000>;
385 regulator-max-microvolt = <1100000>;
389 regulator-name = "vreg_bob";
390 regulator-min-microvolt = <3008000>;
391 regulator-max-microvolt = <3960000>;
392 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
396 regulator-name = "vreg_l1c_1p8";
397 regulator-min-microvolt = <1800000>;
398 regulator-max-microvolt = <1800000>;
399 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
403 regulator-name = "vreg_l3c_3p0";
404 regulator-min-microvolt = <3296000>;
405 regulator-max-microvolt = <3304000>;
406 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
410 regulator-name = "vreg_l4c_1p8";
411 regulator-min-microvolt = <1704000>;
412 regulator-max-microvolt = <3000000>;
413 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
417 regulator-name = "vreg_l5c_1p8";
418 regulator-min-microvolt = <1704000>;
419 regulator-max-microvolt = <3000000>;
420 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
424 regulator-name = "vreg_l6c_1p8";
425 regulator-min-microvolt = <1800000>;
426 regulator-max-microvolt = <3008000>;
427 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
431 regulator-name = "vreg_l7c_3p0";
432 regulator-min-microvolt = <3008000>;
433 regulator-max-microvolt = <3008000>;
434 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
438 regulator-name = "vreg_l8c_1p8";
439 regulator-min-microvolt = <1800000>;
440 regulator-max-microvolt = <1800000>;
441 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
445 regulator-name = "vreg_l9c_2p96";
446 regulator-min-microvolt = <2960000>;
447 regulator-max-microvolt = <3008000>;
448 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
452 regulator-name = "vreg_l12c_1p8";
453 regulator-min-microvolt = <1800000>;
454 regulator-max-microvolt = <1968000>;
455 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
459 regulator-name = "vreg_l13c_3p0";
460 regulator-min-microvolt = <3000000>;
461 regulator-max-microvolt = <3000000>;
462 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
466 regulators-2 {
467 compatible = "qcom,pm8450-rpmh-regulators";
468 qcom,pmic-id = "h";
470 vdd-s1-supply = <&vph_pwr>;
471 vdd-s2-supply = <&vph_pwr>;
472 vdd-s3-supply = <&vph_pwr>;
473 vdd-s4-supply = <&vph_pwr>;
474 vdd-s5-supply = <&vph_pwr>;
475 vdd-s6-supply = <&vph_pwr>;
477 vdd-l2-supply = <&vreg_bob>;
478 vdd-l3-supply = <&vreg_bob>;
479 vdd-l4-supply = <&vreg_bob>;
482 regulator-name = "vreg_s2h_0p95";
483 regulator-min-microvolt = <848000>;
484 regulator-max-microvolt = <1104000>;
488 regulator-name = "vreg_s3h_0p5";
489 regulator-min-microvolt = <500000>;
490 regulator-max-microvolt = <500000>;
494 regulator-name = "vreg_l2h_0p91";
495 regulator-min-microvolt = <880000>;
496 regulator-max-microvolt = <912000>;
497 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
501 regulator-name = "vreg_l3h_0p91";
502 regulator-min-microvolt = <912000>;
503 regulator-max-microvolt = <912000>;
504 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
508 regulators-3 {
509 compatible = "qcom,pmr735a-rpmh-regulators";
510 qcom,pmic-id = "e";
512 vdd-s1-supply = <&vph_pwr>;
513 vdd-s2-supply = <&vph_pwr>;
514 vdd-s3-supply = <&vph_pwr>;
516 vdd-l1-l2-supply = <&vreg_s2e_0p85>;
517 vdd-l3-supply = <&vreg_s1e_1p25>;
518 vdd-l4-supply = <&vreg_s1c_1p86>;
519 vdd-l5-l6-supply = <&vreg_s1c_1p86>;
520 vdd-l7-bob-supply = <&vreg_bob>;
523 regulator-name = "vreg_s1e_1p25";
524 regulator-min-microvolt = <1200000>;
525 regulator-max-microvolt = <1296000>;
529 regulator-name = "vreg_s2e_0p85";
530 regulator-min-microvolt = <500000>;
531 regulator-max-microvolt = <1040000>;
535 regulator-name = "vreg_l1e_0p8";
536 regulator-min-microvolt = <800000>;
537 regulator-max-microvolt = <800000>;
541 regulator-name = "vreg_l2e_0p8";
542 regulator-min-microvolt = <800000>;
543 regulator-max-microvolt = <800000>;
547 regulator-name = "vreg_l3e_1p2";
548 regulator-min-microvolt = <1200000>;
549 regulator-max-microvolt = <1200000>;
553 regulator-name = "vreg_l4e_1p7";
554 regulator-min-microvolt = <1776000>;
555 regulator-max-microvolt = <1776000>;
559 regulator-name = "vreg_l5e_0p88";
560 regulator-min-microvolt = <880000>;
561 regulator-max-microvolt = <880000>;
565 regulator-name = "vreg_l6e_1p2";
566 regulator-min-microvolt = <1200000>;
567 regulator-max-microvolt = <1200000>;
571 regulator-name = "vreg_l7e_2p8";
572 regulator-min-microvolt = <2800000>;
573 regulator-max-microvolt = <2800000>;
585 zap-shader {
586 firmware-name = "qcom/sm8450/a730_zap.mbn";
591 clock-frequency = <400000>;
594 lt9611_codec: hdmi-bridge@2b {
598 interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
600 reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
602 vdd-supply = <<9611_1v2>;
603 vcc-supply = <<9611_3v3>;
605 pinctrl-names = "default";
606 pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
609 #address-cells = <1>;
610 #size-cells = <0>;
616 remote-endpoint = <&mdss_dsi0_out>;
624 remote-endpoint = <&hdmi_connector_out>;
632 clock-frequency = <100000>;
636 typec-mux@42 {
640 interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;
642 vcc-supply = <&vreg_bob>;
643 mode-switch;
644 orientation-switch;
648 remote-endpoint = <&pmic_glink_sbu>;
659 vdda-supply = <&vreg_l6b_1p2>;
664 remote-endpoint = <<9611_a>;
665 data-lanes = <0 1 2 3>;
669 vdds-supply = <&vreg_l5b_0p88>;
678 data-lanes = <0 1>;
683 max-link-speed = <2>;
688 vdda-phy-supply = <&vreg_l5b_0p88>;
689 vdda-pll-supply = <&vreg_l6b_1p2>;
698 vdda-phy-supply = <&vreg_l2h_0p91>;
699 vdda-pll-supply = <&vreg_l6b_1p2>;
703 io-channels = <&pmk8350_vadc PM8350_ADC7_DIE_TEMP(1)>;
704 io-channel-names = "thermal";
708 io-channels = <&pmk8350_vadc PM8350B_ADC7_DIE_TEMP>;
709 io-channel-names = "thermal";
713 io-channels = <&pmk8350_vadc PMR735A_ADC7_DIE_TEMP>;
714 io-channel-names = "thermal";
720 xo-therm@0 {
722 io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
724 qcom,hw-settle-time-us = <200>;
727 skin-msm-therm@1 {
729 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
731 qcom,hw-settle-time-us = <200>;
734 camera-therm@2 {
736 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
738 qcom,hw-settle-time-us = <200>;
741 therm1-therm@3 {
743 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
745 qcom,hw-settle-time-us = <200>;
748 wide-rfc-therm@4 {
750 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
752 qcom,hw-settle-time-us = <200>;
755 rear-tof-therm@5 {
757 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
759 qcom,hw-settle-time-us = <200>;
762 therm2-therm@6 {
764 io-channels = <&pmk8350_vadc PM8350_ADC7_GPIO3_100K_PU(1)>;
766 qcom,hw-settle-time-us = <200>;
769 usb-conn-therm@7 {
771 io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM5_100K_PU>;
773 qcom,hw-settle-time-us = <200>;
787 qcom,hw-settle-time = <200>;
799 qcom,hw-settle-time = <200>;
806 qcom,hw-settle-time = <200>;
813 qcom,hw-settle-time = <200>;
820 qcom,hw-settle-time = <200>;
827 qcom,hw-settle-time = <200>;
834 qcom,hw-settle-time = <200>;
846 qcom,hw-settle-time = <200>;
858 qcom,hw-settle-time = <200>;
865 qcom,hw-settle-time = <200>;
873 firmware-name = "qcom/sm8450/adsp.mbn";
878 firmware-name = "qcom/sm8450/cdsp.mbn";
883 firmware-name = "qcom/sm8450/modem.mbn";
888 firmware-name = "qcom/sm8450/slpi.mbn";
900 cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
901 pinctrl-names = "default", "sleep";
902 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
903 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
904 vmmc-supply = <&vreg_l9c_2p96>;
905 vqmmc-supply = <&vreg_l6c_1p8>;
906 no-sdio;
907 no-mmc;
912 compatible = "qcom,sm8450-sndcard";
913 model = "SM8450-HDK";
914 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
936 wcd-playback-dai-link {
937 link-name = "WCD Playback";
940 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
944 sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
948 sound-dai = <&q6apm>;
952 wcd-capture-dai-link {
953 link-name = "WCD Capture";
956 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
960 sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
964 sound-dai = <&q6apm>;
968 wsa-dai-link {
969 link-name = "WSA Playback";
972 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
976 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
980 sound-dai = <&q6apm>;
984 va-dai-link {
985 link-name = "VA Capture";
988 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
992 sound-dai = <&vamacro 0>;
996 sound-dai = <&q6apm>;
1007 pinctrl-names = "default";
1008 pinctrl-0 = <&spkr_1_sd_n_active>;
1009 powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
1010 #sound-dai-cells = <0>;
1011 sound-name-prefix = "SpkrLeft";
1012 #thermal-sensor-cells = <0>;
1013 vdd-supply = <&vreg_s10b_1p8>;
1019 pinctrl-names = "default";
1020 pinctrl-0 = <&spkr_2_sd_n_active>;
1021 powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
1022 #sound-dai-cells = <0>;
1023 sound-name-prefix = "SpkrRight";
1024 #thermal-sensor-cells = <0>;
1025 vdd-supply = <&vreg_s10b_1p8>;
1035 qcom,rx-port-mapping = <1 2 3 4 5>;
1045 qcom,tx-port-mapping = <1 1 2 3>;
1050 gpio-reserved-ranges = <28 4>, <36 4>;
1052 lt9611_irq_pin: lt9611-irq-state {
1055 bias-disable;
1058 lt9611_rst_pin: lt9611-rst-state {
1061 output-high;
1064 sdc2_card_det_n: sd-card-det-n-state {
1067 drive-strength = <2>;
1068 bias-pull-up;
1079 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1081 vcc-supply = <&vreg_l7b_2p5>;
1082 vcc-max-microamp = <1100000>;
1083 vccq-supply = <&vreg_l9b_1p2>;
1084 vccq-max-microamp = <1200000>;
1085 vdd-hba-supply = <&vreg_l9b_1p2>;
1091 vdda-phy-supply = <&vreg_l5b_0p88>;
1092 vdda-pll-supply = <&vreg_l6b_1p2>;
1101 usb-role-switch;
1105 remote-endpoint = <&pmic_glink_hs_in>;
1111 vdda-pll-supply = <&vreg_l5b_0p88>;
1112 vdda18-supply = <&vreg_l1c_1p8>;
1113 vdda33-supply = <&vreg_l2b_3p07>;
1119 vdda-phy-supply = <&vreg_l6b_1p2>;
1120 vdda-pll-supply = <&vreg_l1b_0p91>;
1124 remote-endpoint = <&pmic_glink_ss_in>;
1128 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
1129 pinctrl-names = "default";
1130 vdd-micb-supply = <&vreg_s10b_1p8>;
1131 qcom,dmic-sample-rate = <600000>;
1137 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
1140 drive-strength = <16>;
1141 bias-disable;
1142 output-low;
1145 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
1148 drive-strength = <16>;
1149 bias-disable;
1150 output-low;
1153 wcd_default: wcd-reset-n-active-state {
1156 drive-strength = <16>;
1157 bias-disable;
1158 output-low;