Lines Matching +full:drdy +full:- +full:int +full:- +full:pin
1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/irq.h>
11 #include <dt-bindings/sound/apq8016-lpass.h>
21 stdout-path = "serial0";
24 reserved-memory {
26 tz-apps@85500000 {
28 no-map;
32 gpio-keys {
33 compatible = "gpio-keys";
35 pinctrl-0 = <&gpio_keys_default>;
36 pinctrl-names = "default";
40 volume-up-button {
46 home-button {
53 gpio-hall-sensor {
54 compatible = "gpio-keys";
56 pinctrl-0 = <&gpio_hall_sensor_default>;
57 pinctrl-names = "default";
61 hall-sensor-switch {
64 linux,input-type = <EV_SW>;
66 linux,can-disable;
74 light-sensor@10 {
83 vdd-supply = <&pm8916_l17>;
84 vddio-supply = <&pm8916_l5>;
86 interrupt-parent = <&tlmm>;
89 st,drdy-int-pin = <1>;
90 mount-matrix = "0", "1", "0",
91 "-1", "0", "0",
94 pinctrl-0 = <&accel_int_default>;
95 pinctrl-names = "default";
103 compatible = "maxim,max77849-battery";
106 maxim,rsns-microohm = <10000>;
107 maxim,over-heat-temp = <600>;
108 maxim,over-volt = <4400>;
110 interrupt-parent = <&tlmm>;
113 pinctrl-0 = <&fuelgauge_int_default>;
114 pinctrl-names = "default";
135 dai-link@3 {
137 qcom,playback-sd-lines = <1>;
152 regulator-min-microvolt = <2850000>;
153 regulator-max-microvolt = <2850000>;
165 qcom,sd-lines = <1>;
174 pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
175 pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
176 pinctrl-names = "default", "sleep";
178 cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
184 audio-routing =
189 sound_link_backend2: backend2-dai-link {
190 link-name = "Quaternary MI2S";
193 sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
196 sound-dai = <&q6routing>;
199 sound-dai = <&speaker_codec>;
236 accel_int_default: accel-int-default-state {
239 drive-strength = <2>;
240 bias-disable;
243 fuelgauge_int_default: fuelgauge-int-default-state {
246 drive-strength = <2>;
247 bias-disable;
250 gpio_keys_default: gpio-keys-default-state {
253 drive-strength = <2>;
254 bias-pull-up;
257 gpio_hall_sensor_default: gpio-hall-sensor-default-state {
260 drive-strength = <2>;
261 bias-disable;
264 sdc2_cd_default: sdc2-cd-default-state {
267 drive-strength = <2>;
268 bias-disable;