Lines Matching +full:shutdown +full:- +full:gpios

1 // SPDX-License-Identifier: GPL-2.0+
3  * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
9 /dts-v1/;
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/leds/common.h>
15 #include "cn9130-sr-som.dtsi"
16 #include "cn9130-cf.dtsi"
20 	compatible = "solidrun,cn9130-clearfog-base",
21 		     "solidrun,cn9130-sr-som", "marvell,cn9130";
23 	gpio-keys {
24 		compatible = "gpio-keys";
25 		pinctrl-0 = <&rear_button_pins>;
26 		pinctrl-names = "default";
28 		button-0 {
31 			gpios = <&cp0_gpio1 31 GPIO_ACTIVE_LOW>;
32 			linux,can-disable;
37 	rfkill-m2-gnss {
38 		compatible = "rfkill-gpio";
40 		radio-type = "gps";
41 		/* rfkill-gpio inverts internally */
42 		shutdown-gpios = <&expander0 9 GPIO_ACTIVE_HIGH>;
45 	/* M.2 is B-keyed, so w-disable is for WWAN */
46 	rfkill-m2-wwan {
47 		compatible = "rfkill-gpio";
49 		radio-type = "wwan";
50 		/* rfkill-gpio inverts internally */
51 		shutdown-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
55 /* SRDS #3 - SGMII 1GE */
59 	phy-mode = "sgmii";
66 	 * - LED[0]: link/activity: On/blink (green)
67 	 * - LED[1]: link is 100/1000Mbps: On (yellow)
68 	 * - LED[2]: high impedance (floating)
70 	marvell,reg-init = <3 16 0xf000 0x0a61>;
73 		#address-cells = <1>;
74 		#size-cells = <0>;
80 			default-state = "keep";
87 			default-state = "keep";
93 	sim-select-hog {
94 		gpio-hog;
95 		gpios = <27 GPIO_ACTIVE_HIGH>;
96 		output-high;
97 		line-name = "sim-select";
102 	phy1: ethernet-phy@1 {
106 		 * - LED[0]: link/activity: On/blink (green)
107 		 * - LED[1]: link is 100/1000Mbps: On (yellow)
108 		 * - LED[2]: high impedance (floating)
111 		 * - on-state: low
112 		 * - off-state: high (not hi-z, to avoid residual glow)
114 		marvell,reg-init = <3 16 0xf000 0x0a61>,
118 			#address-cells = <1>;
119 			#size-cells = <0>;
125 				default-state = "keep";
132 				default-state = "keep";
139 	pinctrl-0 = <&sim_select_pins>;
140 	pintrl-names = "default";
142 	rear_button_pins: cp0-rear-button-pins {
147 	sim_select_pins: cp0-sim-select-pins {
154  * SRDS #4 - USB 3.0 host on M.2 connector
155  * USB-2.0 Host on Type-A connector
159 	phy-names = "comphy", "utmi";
165 	m2-full-card-power-off-hog {
166 		gpio-hog;
167 		gpios = <2 GPIO_ACTIVE_LOW>;
168 		output-low;
169 		line-name = "m2-full-card-power-off";
172 	m2-reset-hog {
173 		gpio-hog;
174 		gpios = <10 GPIO_ACTIVE_LOW>;
175 		output-low;
176 		line-name = "m2-reset";