Lines Matching +full:vdd10 +full:- +full:supply
1 // SPDX-License-Identifier: GPL-2.0
11 /dts-v1/;
13 #include <dt-bindings/clock/samsung,s2mps11.h>
14 #include <dt-bindings/gpio/gpio.h>
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/interrupt-controller/irq.h>
17 #include <dt-bindings/sound/samsung-i2s.h>
48 stdout-path = &serial_1;
56 gpio-keys {
57 compatible = "gpio-keys";
59 power-key {
63 debounce-interval = <10>;
66 volume-up-key {
69 label = "volume-up key";
70 debounce-interval = <10>;
73 volume-down-key {
76 label = "volume-down key";
77 debounce-interval = <10>;
80 homepage-key {
84 debounce-interval = <10>;
88 i2c_max98504: i2c-gpio-0 {
89 compatible = "i2c-gpio";
90 sda-gpios = <&gpd0 1 GPIO_ACTIVE_HIGH>;
91 scl-gpios = <&gpd0 0 GPIO_ACTIVE_HIGH>;
92 i2c-gpio,delay-us = <2>;
93 #address-cells = <1>;
94 #size-cells = <0>;
100 DIOVDD-supply = <&ldo3_reg>;
101 DVDD-supply = <&ldo3_reg>;
102 PVDD-supply = <&vph_pwr_regulator>;
106 vph_pwr_regulator: regulator-vph-pwr {
107 compatible = "regulator-fixed";
108 regulator-name = "VPH_PWR";
109 regulator-min-microvolt = <4200000>;
110 regulator-max-microvolt = <4200000>;
113 irda_regulator: regulator-irda {
114 compatible = "regulator-fixed";
115 enable-active-high;
117 regulator-name = "irda_regulator";
121 compatible = "samsung,tm2-audio";
122 audio-codec = <&wm5110>, <&hdmi>;
123 i2s-controller = <&i2s0 0>, <&i2s1 0>;
124 audio-amplifier = <&max98504>;
125 mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
127 audio-routing = /* Headphone */
143 vdd-supply = <&ldo3_reg>;
146 thermistor-ap {
148 pullup-uv = <1800000>;
149 pullup-ohm = <100000>;
150 pulldown-ohm = <0>;
151 io-channels = <&adc 0>;
154 thermistor-battery {
156 pullup-uv = <1800000>;
157 pullup-ohm = <100000>;
158 pulldown-ohm = <0>;
159 io-channels = <&adc 1>;
160 #thermal-sensor-cells = <0>;
163 thermistor-charger {
165 pullup-uv = <1800000>;
166 pullup-ohm = <100000>;
167 pulldown-ohm = <0>;
168 io-channels = <&adc 2>;
173 devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
174 vdd-supply = <&buck4_reg>;
175 exynos,saturation-ratio = <10>;
225 assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>,
246 assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>,
255 assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
262 assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
272 assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
280 assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
285 assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
287 assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
292 assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
293 assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
297 assigned-clocks = <&cmu_mif CLK_MOUT_SCLK_DSD_A>, <&cmu_mif CLK_DIV_SCLK_DSD>;
298 assigned-clock-parents = <&cmu_mif CLK_MOUT_MFC_PLL_DIV2>;
299 assigned-clock-rates = <0>, <333000000>;
303 assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
307 assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
314 assigned-clocks = <&cmu_top CLK_FOUT_AUD_PLL>;
315 assigned-clock-rates = <196608001>;
319 cpu-supply = <&buck3_reg>;
323 cpu-supply = <&buck2_reg>;
334 #address-cells = <1>;
335 #size-cells = <0>;
340 remote-endpoint = <&hdmi_to_tv>;
348 vddcore-supply = <&ldo6_reg>;
349 vddio-supply = <&ldo7_reg>;
350 samsung,burst-clock-frequency = <512000000>;
351 samsung,esc-clock-frequency = <16000000>;
352 samsung,pll-clock-frequency = <24000000>;
353 pinctrl-names = "default";
354 pinctrl-0 = <&te_irq>;
358 mali-supply = <&buck6_reg>;
363 hpd-gpios = <&gpa3 0 GPIO_ACTIVE_HIGH>;
365 vdd-supply = <&ldo6_reg>;
366 vdd_osc-supply = <&ldo7_reg>;
367 vdd_pll-supply = <&ldo6_reg>;
370 #address-cells = <1>;
371 #size-cells = <0>;
376 remote-endpoint = <&tv_to_hdmi>;
383 remote-endpoint = <&mhl_to_hdmi>;
391 clock-frequency = <2500000>;
394 compatible = "samsung,s2mps13-pmic";
395 interrupt-parent = <&gpa0>;
398 samsung,s2mps11-wrstbi-ground;
399 wakeup-source;
402 compatible = "samsung,s2mps13-clk";
403 #clock-cells = <1>;
404 clock-output-names = "s2mps13_ap", "s2mps13_cp",
410 regulator-name = "VDD_ALIVE_0.9V_AP";
411 regulator-min-microvolt = <900000>;
412 regulator-max-microvolt = <900000>;
413 regulator-always-on;
417 regulator-name = "VDDQ_MMC2_2.8V_AP";
418 regulator-min-microvolt = <2800000>;
419 regulator-max-microvolt = <2800000>;
420 regulator-always-on;
421 regulator-state-mem {
422 regulator-off-in-suspend;
427 regulator-name = "VDD1_E_1.8V_AP";
428 regulator-min-microvolt = <1800000>;
429 regulator-max-microvolt = <1800000>;
430 regulator-always-on;
434 regulator-name = "VDD10_MIF_PLL_1.0V_AP";
435 regulator-min-microvolt = <1300000>;
436 regulator-max-microvolt = <1300000>;
437 regulator-always-on;
438 regulator-state-mem {
439 regulator-off-in-suspend;
444 regulator-name = "VDD10_DPLL_1.0V_AP";
445 regulator-min-microvolt = <1000000>;
446 regulator-max-microvolt = <1000000>;
447 regulator-always-on;
448 regulator-state-mem {
449 regulator-off-in-suspend;
454 regulator-name = "VDD10_MIPI2L_1.0V_AP";
455 regulator-min-microvolt = <1000000>;
456 regulator-max-microvolt = <1000000>;
457 regulator-state-mem {
458 regulator-off-in-suspend;
463 regulator-name = "VDD18_MIPI2L_1.8V_AP";
464 regulator-min-microvolt = <1800000>;
465 regulator-max-microvolt = <1800000>;
466 regulator-always-on;
467 regulator-state-mem {
468 regulator-off-in-suspend;
473 regulator-name = "VDD18_LLI_1.8V_AP";
474 regulator-min-microvolt = <1800000>;
475 regulator-max-microvolt = <1800000>;
476 regulator-always-on;
477 regulator-state-mem {
478 regulator-off-in-suspend;
483 regulator-name = "VDD18_ABB_ETC_1.8V_AP";
484 regulator-min-microvolt = <1800000>;
485 regulator-max-microvolt = <1800000>;
486 regulator-always-on;
487 regulator-state-mem {
488 regulator-off-in-suspend;
493 regulator-name = "VDD33_USB30_3.0V_AP";
494 regulator-min-microvolt = <3000000>;
495 regulator-max-microvolt = <3000000>;
496 regulator-state-mem {
497 regulator-off-in-suspend;
502 regulator-name = "VDD_INT_M_1.0V_AP";
503 regulator-min-microvolt = <1000000>;
504 regulator-max-microvolt = <1000000>;
505 regulator-always-on;
506 regulator-state-mem {
507 regulator-off-in-suspend;
512 regulator-name = "VDD_KFC_M_1.1V_AP";
513 regulator-min-microvolt = <800000>;
514 regulator-max-microvolt = <1350000>;
515 regulator-always-on;
519 regulator-name = "VDD_G3D_M_0.95V_AP";
520 regulator-min-microvolt = <950000>;
521 regulator-max-microvolt = <950000>;
522 regulator-always-on;
523 regulator-state-mem {
524 regulator-off-in-suspend;
529 regulator-name = "VDDQ_M1_LDO_1.2V_AP";
530 regulator-min-microvolt = <1200000>;
531 regulator-max-microvolt = <1200000>;
532 regulator-always-on;
533 regulator-state-mem {
534 regulator-off-in-suspend;
539 regulator-name = "VDDQ_M2_LDO_1.2V_AP";
540 regulator-min-microvolt = <1200000>;
541 regulator-max-microvolt = <1200000>;
542 regulator-always-on;
543 regulator-state-mem {
544 regulator-off-in-suspend;
549 regulator-name = "VDDQ_EFUSE";
550 regulator-min-microvolt = <1400000>;
551 regulator-max-microvolt = <3400000>;
552 regulator-always-on;
556 regulator-name = "V_TFLASH_2.8V_AP";
557 regulator-min-microvolt = <2800000>;
558 regulator-max-microvolt = <2800000>;
562 regulator-name = "V_CODEC_1.8V_AP";
563 regulator-min-microvolt = <1800000>;
564 regulator-max-microvolt = <1800000>;
568 regulator-name = "VDDA_1.8V_COMP";
569 regulator-min-microvolt = <1800000>;
570 regulator-max-microvolt = <1800000>;
571 regulator-always-on;
575 regulator-name = "VCC_2.8V_AP";
576 regulator-min-microvolt = <2800000>;
577 regulator-max-microvolt = <2800000>;
578 regulator-always-on;
582 regulator-name = "VT_CAM_1.8V";
583 regulator-min-microvolt = <1800000>;
584 regulator-max-microvolt = <1800000>;
588 regulator-name = "CAM_IO_1.8V_AP";
589 regulator-min-microvolt = <1800000>;
590 regulator-max-microvolt = <1800000>;
594 regulator-name = "CAM_SEN_CORE_1.05V_AP";
595 regulator-min-microvolt = <1050000>;
596 regulator-max-microvolt = <1050000>;
600 regulator-name = "VT_CAM_1.2V";
601 regulator-min-microvolt = <1200000>;
602 regulator-max-microvolt = <1200000>;
606 regulator-name = "UNUSED_LDO25";
607 regulator-min-microvolt = <2800000>;
608 regulator-max-microvolt = <2800000>;
612 regulator-name = "CAM_AF_2.8V_AP";
613 regulator-min-microvolt = <2800000>;
614 regulator-max-microvolt = <2800000>;
618 regulator-name = "VCC_3.0V_LCD_AP";
619 regulator-min-microvolt = <3000000>;
620 regulator-max-microvolt = <3000000>;
624 regulator-name = "VCC_1.8V_LCD_AP";
625 regulator-min-microvolt = <1800000>;
626 regulator-max-microvolt = <1800000>;
630 regulator-name = "VT_CAM_2.8V";
631 regulator-min-microvolt = <3000000>;
632 regulator-max-microvolt = <3000000>;
636 regulator-name = "TSP_AVDD_3.3V_AP";
637 regulator-min-microvolt = <3300000>;
638 regulator-max-microvolt = <3300000>;
649 regulator-name = "VTOUCH_1.8V_AP";
650 regulator-min-microvolt = <1800000>;
651 regulator-max-microvolt = <1800000>;
655 regulator-name = "VTOUCH_LED_3.3V";
656 regulator-min-microvolt = <2500000>;
657 regulator-max-microvolt = <3300000>;
658 regulator-ramp-delay = <12500>;
662 regulator-name = "VCC_1.8V_MHL_AP";
663 regulator-min-microvolt = <1000000>;
664 regulator-max-microvolt = <2100000>;
668 regulator-name = "OIS_VM_2.8V";
669 regulator-min-microvolt = <1800000>;
670 regulator-max-microvolt = <2800000>;
674 regulator-name = "VSIL_1.0V";
675 regulator-min-microvolt = <1000000>;
676 regulator-max-microvolt = <1000000>;
680 regulator-name = "VF_1.8V";
681 regulator-min-microvolt = <1800000>;
682 regulator-max-microvolt = <1800000>;
693 regulator-name = "V_HRM_1.8V";
694 regulator-min-microvolt = <1800000>;
695 regulator-max-microvolt = <1800000>;
699 regulator-name = "V_HRM_3.3V";
700 regulator-min-microvolt = <3300000>;
701 regulator-max-microvolt = <3300000>;
705 regulator-name = "VDD_MIF_0.9V_AP";
706 regulator-min-microvolt = <600000>;
707 regulator-max-microvolt = <1500000>;
708 regulator-always-on;
709 regulator-state-mem {
710 regulator-off-in-suspend;
715 regulator-name = "VDD_EGL_1.0V_AP";
716 regulator-min-microvolt = <900000>;
717 regulator-max-microvolt = <1300000>;
718 regulator-always-on;
719 regulator-state-mem {
720 regulator-off-in-suspend;
725 regulator-name = "VDD_KFC_1.0V_AP";
726 regulator-min-microvolt = <800000>;
727 regulator-max-microvolt = <1200000>;
728 regulator-always-on;
729 regulator-state-mem {
730 regulator-off-in-suspend;
735 regulator-name = "VDD_INT_0.95V_AP";
736 regulator-min-microvolt = <600000>;
737 regulator-max-microvolt = <1500000>;
738 regulator-always-on;
739 regulator-state-mem {
740 regulator-off-in-suspend;
745 regulator-name = "VDD_DISP_CAM0_0.9V_AP";
746 regulator-min-microvolt = <600000>;
747 regulator-max-microvolt = <1500000>;
748 regulator-always-on;
749 regulator-state-mem {
750 regulator-off-in-suspend;
755 regulator-name = "VDD_G3D_0.9V_AP";
756 regulator-min-microvolt = <600000>;
757 regulator-max-microvolt = <1500000>;
758 regulator-always-on;
759 regulator-state-mem {
760 regulator-off-in-suspend;
765 regulator-name = "VDD_MEM1_1.2V_AP";
766 regulator-min-microvolt = <1200000>;
767 regulator-max-microvolt = <1200000>;
768 regulator-always-on;
772 regulator-name = "VDD_LLDO_1.35V_AP";
773 regulator-min-microvolt = <1350000>;
774 regulator-max-microvolt = <3300000>;
775 regulator-always-on;
779 regulator-name = "VDD_MLDO_2.0V_AP";
780 regulator-min-microvolt = <1350000>;
781 regulator-max-microvolt = <3300000>;
782 regulator-always-on;
786 regulator-name = "vdd_mem2";
787 regulator-min-microvolt = <550000>;
788 regulator-max-microvolt = <1500000>;
789 regulator-always-on;
799 compatible = "samsung,s3fwrn5-i2c";
801 interrupt-parent = <&gpa1>;
803 en-gpios = <&gpf1 4 GPIO_ACTIVE_LOW>;
804 wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;
814 interrupt-parent = <&gpa1>;
816 avdd-supply = <&ldo30_reg>;
817 vdd-supply = <&ldo31_reg>;
823 clock-frequency = <1000000>;
828 cvcc10-supply = <&ldo36_reg>;
829 iovcc18-supply = <&ldo34_reg>;
830 interrupt-parent = <&gpf0>;
832 reset-gpios = <&gpv7 0 GPIO_ACTIVE_LOW>;
834 clock-names = "xtal";
837 #address-cells = <1>;
838 #size-cells = <0>;
843 remote-endpoint = <&hdmi_to_mhl>;
850 remote-endpoint = <&musb_con_to_mhl>;
862 interrupt-parent = <&gpa1>;
867 compatible = "maxim,max77843-muic";
870 compatible = "samsung,usb-connector-11pin",
871 "usb-b-connector";
872 label = "micro-USB";
876 #address-cells = <1>;
877 #size-cells = <0>;
893 remote-endpoint = <&mhl_to_musb_con>;
902 remote-endpoint = <&usb_to_muic>;
909 compatible = "maxim,max77843-regulator";
911 regulator-name = "SAFEOUT1";
912 regulator-min-microvolt = <3300000>;
913 regulator-max-microvolt = <4950000>;
917 regulator-name = "SAFEOUT2";
918 regulator-min-microvolt = <3300000>;
919 regulator-max-microvolt = <4950000>;
923 regulator-name = "CHARGER";
924 regulator-min-microamp = <100000>;
925 regulator-max-microamp = <3150000>;
929 haptic: motor-driver {
930 compatible = "maxim,max77843-haptic";
931 haptic-supply = <&ldo38_reg>;
946 assigned-clocks = <&i2s1 CLK_I2S_RCLK_SRC>;
947 assigned-clock-parents = <&cmu_peric CLK_SCLK_I2S1>;
953 mmc-ddr-1_8v;
954 mmc-hs200-1_8v;
955 mmc-hs400-1_8v;
956 cap-mmc-highspeed;
957 non-removable;
958 card-detect-delay = <200>;
959 samsung,dw-mshc-ciu-div = <3>;
960 samsung,dw-mshc-sdr-timing = <0 4>;
961 samsung,dw-mshc-ddr-timing = <0 2>;
962 samsung,dw-mshc-hs400-timing = <0 3>;
963 samsung,read-strobe-delay = <90>;
964 fifo-depth = <0x80>;
965 pinctrl-names = "default";
966 pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
968 bus-width = <8>;
969 assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
970 assigned-clock-rates = <800000000>;
975 cap-sd-highspeed;
976 disable-wp;
977 cd-gpios = <&gpa2 4 GPIO_ACTIVE_LOW>;
978 card-detect-delay = <200>;
979 samsung,dw-mshc-ciu-div = <3>;
980 samsung,dw-mshc-sdr-timing = <0 4>;
981 samsung,dw-mshc-ddr-timing = <0 2>;
982 fifo-depth = <0x80>;
983 pinctrl-names = "default";
984 pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
985 bus-width = <4>;
990 pinctrl-names = "default";
991 pinctrl-0 = <&pcie_bus &pcie_wlanen>;
992 vdd10-supply = <&ldo6_reg>;
993 vdd18-supply = <&ldo7_reg>;
994 assigned-clocks = <&cmu_fsys CLK_MOUT_SCLK_PCIE_100_USER>,
996 assigned-clock-parents = <&cmu_top CLK_SCLK_PCIE_100_FSYS>,
998 assigned-clock-rates = <0>, <100000000>;
999 interrupt-map-mask = <0 0 0 0>;
1000 interrupt-map = <0 0 0 0 &gic GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
1010 ppmu_event0_d0_general: ppmu-event0-d0-general {
1011 event-name = "ppmu-event0-d0-general";
1019 ppmu_event0_d1_general: ppmu-event0-d1-general {
1020 event-name = "ppmu-event0-d1-general";
1026 pinctrl-names = "default";
1027 pinctrl-0 = <&initial_alive>;
1029 initial_alive: initial-state {
1030 PIN_IN(gpa0-0, DOWN, FAST_SR1);
1031 PIN_IN(gpa0-1, NONE, FAST_SR1);
1032 PIN_IN(gpa0-2, DOWN, FAST_SR1);
1033 PIN_IN(gpa0-3, NONE, FAST_SR1);
1034 PIN_IN(gpa0-4, NONE, FAST_SR1);
1035 PIN_IN(gpa0-5, DOWN, FAST_SR1);
1036 PIN_IN(gpa0-6, NONE, FAST_SR1);
1037 PIN_IN(gpa0-7, NONE, FAST_SR1);
1039 PIN_IN(gpa1-0, UP, FAST_SR1);
1040 PIN_IN(gpa1-1, UP, FAST_SR1);
1041 PIN_IN(gpa1-2, NONE, FAST_SR1);
1042 PIN_IN(gpa1-3, DOWN, FAST_SR1);
1043 PIN_IN(gpa1-4, DOWN, FAST_SR1);
1044 PIN_IN(gpa1-5, NONE, FAST_SR1);
1045 PIN_IN(gpa1-6, NONE, FAST_SR1);
1046 PIN_IN(gpa1-7, NONE, FAST_SR1);
1048 PIN_IN(gpa2-0, NONE, FAST_SR1);
1049 PIN_IN(gpa2-1, NONE, FAST_SR1);
1050 PIN_IN(gpa2-2, NONE, FAST_SR1);
1051 PIN_IN(gpa2-3, DOWN, FAST_SR1);
1052 PIN_IN(gpa2-4, NONE, FAST_SR1);
1053 PIN_IN(gpa2-5, DOWN, FAST_SR1);
1054 PIN_IN(gpa2-6, DOWN, FAST_SR1);
1055 PIN_IN(gpa2-7, NONE, FAST_SR1);
1057 PIN_IN(gpa3-0, DOWN, FAST_SR1);
1058 PIN_IN(gpa3-1, DOWN, FAST_SR1);
1059 PIN_IN(gpa3-2, NONE, FAST_SR1);
1060 PIN_IN(gpa3-3, DOWN, FAST_SR1);
1061 PIN_IN(gpa3-4, NONE, FAST_SR1);
1062 PIN_IN(gpa3-5, DOWN, FAST_SR1);
1063 PIN_IN(gpa3-6, DOWN, FAST_SR1);
1064 PIN_IN(gpa3-7, DOWN, FAST_SR1);
1066 PIN_IN(gpf1-0, NONE, FAST_SR1);
1067 PIN_IN(gpf1-1, NONE, FAST_SR1);
1068 PIN_IN(gpf1-2, DOWN, FAST_SR1);
1069 PIN_IN(gpf1-4, UP, FAST_SR1);
1070 PIN_OT(gpf1-5, NONE, FAST_SR1);
1071 PIN_IN(gpf1-6, DOWN, FAST_SR1);
1072 PIN_IN(gpf1-7, DOWN, FAST_SR1);
1074 PIN_IN(gpf2-0, DOWN, FAST_SR1);
1075 PIN_IN(gpf2-1, DOWN, FAST_SR1);
1076 PIN_IN(gpf2-2, DOWN, FAST_SR1);
1077 PIN_IN(gpf2-3, DOWN, FAST_SR1);
1079 PIN_IN(gpf3-0, DOWN, FAST_SR1);
1080 PIN_IN(gpf3-1, DOWN, FAST_SR1);
1081 PIN_IN(gpf3-2, NONE, FAST_SR1);
1082 PIN_IN(gpf3-3, DOWN, FAST_SR1);
1084 PIN_IN(gpf4-0, DOWN, FAST_SR1);
1085 PIN_IN(gpf4-1, DOWN, FAST_SR1);
1086 PIN_IN(gpf4-2, DOWN, FAST_SR1);
1087 PIN_IN(gpf4-3, DOWN, FAST_SR1);
1088 PIN_IN(gpf4-4, DOWN, FAST_SR1);
1089 PIN_IN(gpf4-5, DOWN, FAST_SR1);
1090 PIN_IN(gpf4-6, DOWN, FAST_SR1);
1091 PIN_IN(gpf4-7, DOWN, FAST_SR1);
1093 PIN_IN(gpf5-0, DOWN, FAST_SR1);
1094 PIN_IN(gpf5-1, DOWN, FAST_SR1);
1095 PIN_IN(gpf5-2, DOWN, FAST_SR1);
1096 PIN_IN(gpf5-3, DOWN, FAST_SR1);
1097 PIN_OT(gpf5-4, NONE, FAST_SR1);
1098 PIN_IN(gpf5-5, DOWN, FAST_SR1);
1099 PIN_IN(gpf5-6, DOWN, FAST_SR1);
1100 PIN_IN(gpf5-7, DOWN, FAST_SR1);
1103 te_irq: te-irq-pins {
1104 samsung,pins = "gpf1-3";
1105 samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
1110 pinctrl-names = "default";
1111 pinctrl-0 = <&initial_cpif>;
1113 initial_cpif: initial-state {
1114 PIN_IN(gpv6-0, DOWN, FAST_SR1);
1115 PIN_IN(gpv6-1, DOWN, FAST_SR1);
1120 pinctrl-names = "default";
1121 pinctrl-0 = <&initial_ese>;
1123 pcie_wlanen: pcie-wlanen-pins {
1124 samsung,pins = "gpj2-0";
1125 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
1126 samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
1127 samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
1130 initial_ese: initial-state {
1131 PIN_IN(gpj2-1, DOWN, FAST_SR1);
1132 PIN_IN(gpj2-2, DOWN, FAST_SR1);
1137 pinctrl-names = "default";
1138 pinctrl-0 = <&initial_fsys>;
1140 initial_fsys: initial-state {
1141 PIN_IN(gpr3-0, NONE, FAST_SR1);
1142 PIN_IN(gpr3-1, DOWN, FAST_SR1);
1143 PIN_IN(gpr3-2, DOWN, FAST_SR1);
1144 PIN_IN(gpr3-3, DOWN, FAST_SR1);
1145 PIN_IN(gpr3-7, NONE, FAST_SR1);
1150 pinctrl-names = "default";
1151 pinctrl-0 = <&initial_imem>;
1153 initial_imem: initial-state {
1154 PIN_IN(gpf0-0, UP, FAST_SR1);
1155 PIN_IN(gpf0-1, UP, FAST_SR1);
1156 PIN_IN(gpf0-2, DOWN, FAST_SR1);
1157 PIN_IN(gpf0-3, UP, FAST_SR1);
1158 PIN_IN(gpf0-4, DOWN, FAST_SR1);
1159 PIN_IN(gpf0-5, NONE, FAST_SR1);
1160 PIN_IN(gpf0-6, DOWN, FAST_SR1);
1161 PIN_IN(gpf0-7, UP, FAST_SR1);
1166 pinctrl-names = "default";
1167 pinctrl-0 = <&initial_nfc>;
1169 initial_nfc: initial-state {
1170 PIN_IN(gpj0-2, DOWN, FAST_SR1);
1175 pinctrl-names = "default";
1176 pinctrl-0 = <&initial_peric>;
1178 initial_peric: initial-state {
1179 PIN_IN(gpv7-0, DOWN, FAST_SR1);
1180 PIN_IN(gpv7-1, DOWN, FAST_SR1);
1181 PIN_IN(gpv7-2, NONE, FAST_SR1);
1182 PIN_IN(gpv7-3, DOWN, FAST_SR1);
1183 PIN_IN(gpv7-4, DOWN, FAST_SR1);
1184 PIN_IN(gpv7-5, DOWN, FAST_SR1);
1186 PIN_IN(gpb0-4, DOWN, FAST_SR1);
1188 PIN_IN(gpc0-2, DOWN, FAST_SR1);
1189 PIN_IN(gpc0-5, DOWN, FAST_SR1);
1190 PIN_IN(gpc0-7, DOWN, FAST_SR1);
1192 PIN_IN(gpc1-1, DOWN, FAST_SR1);
1194 PIN_IN(gpc3-4, NONE, FAST_SR1);
1195 PIN_IN(gpc3-5, NONE, FAST_SR1);
1196 PIN_IN(gpc3-6, NONE, FAST_SR1);
1197 PIN_IN(gpc3-7, NONE, FAST_SR1);
1199 PIN_OT(gpg0-0, NONE, FAST_SR1);
1200 PIN_F2(gpg0-1, DOWN, FAST_SR1);
1202 PIN_IN(gpd2-5, DOWN, FAST_SR1);
1204 PIN_IN(gpd4-0, NONE, FAST_SR1);
1205 PIN_IN(gpd4-1, DOWN, FAST_SR1);
1206 PIN_IN(gpd4-2, DOWN, FAST_SR1);
1207 PIN_IN(gpd4-3, DOWN, FAST_SR1);
1208 PIN_IN(gpd4-4, DOWN, FAST_SR1);
1210 PIN_IN(gpd6-3, DOWN, FAST_SR1);
1212 PIN_IN(gpd8-1, UP, FAST_SR1);
1214 PIN_IN(gpg1-0, DOWN, FAST_SR1);
1215 PIN_IN(gpg1-1, DOWN, FAST_SR1);
1216 PIN_IN(gpg1-2, DOWN, FAST_SR1);
1217 PIN_IN(gpg1-3, DOWN, FAST_SR1);
1218 PIN_IN(gpg1-4, DOWN, FAST_SR1);
1220 PIN_IN(gpg2-0, DOWN, FAST_SR1);
1221 PIN_IN(gpg2-1, DOWN, FAST_SR1);
1223 PIN_IN(gpg3-0, DOWN, FAST_SR1);
1224 PIN_IN(gpg3-1, DOWN, FAST_SR1);
1225 PIN_IN(gpg3-5, DOWN, FAST_SR1);
1230 pinctrl-names = "default";
1231 pinctrl-0 = <&initial_touch>;
1233 initial_touch: initial-state {
1234 PIN_IN(gpj1-2, DOWN, FAST_SR1);
1239 pinctrl-0 = <&pwm0_out>;
1240 pinctrl-names = "default";
1249 assigned-clocks = <&pmu_system_controller 0>;
1250 assigned-clock-parents = <&xxti>;
1261 compatible = "brcm,bcm43438-bt";
1262 max-speed = <3000000>;
1263 shutdown-gpios = <&gpd4 0 GPIO_ACTIVE_HIGH>;
1264 device-wakeup-gpios = <&gpr3 7 GPIO_ACTIVE_HIGH>;
1265 host-wakeup-gpios = <&gpa2 2 GPIO_ACTIVE_HIGH>;
1267 clock-names = "extclk";
1272 cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
1275 wm5110: audio-codec@0 {
1278 spi-max-frequency = <20000000>;
1279 interrupt-parent = <&gpa0>;
1283 clock-names = "mclk1", "mclk2";
1285 gpio-controller;
1286 #gpio-cells = <2>;
1287 interrupt-controller;
1288 #interrupt-cells = <2>;
1290 wlf,micd-detect-debounce = <300>;
1291 wlf,micd-bias-start-time = <0x1>;
1292 wlf,micd-rate = <0x7>;
1293 wlf,micd-dbtime = <0x2>;
1294 wlf,micd-force-micbias;
1295 wlf,micd-configs = <0x0 1 0>;
1296 wlf,hpdet-channel = <1>;
1304 AVDD-supply = <&ldo18_reg>;
1305 DBVDD1-supply = <&ldo18_reg>;
1306 CPVDD-supply = <&ldo18_reg>;
1307 DBVDD2-supply = <&ldo18_reg>;
1308 DBVDD3-supply = <&ldo18_reg>;
1309 SPKVDDL-supply = <&vph_pwr_regulator>;
1310 SPKVDDR-supply = <&vph_pwr_regulator>;
1312 controller-data {
1313 samsung,spi-feedback-delay = <0>;
1320 no-cs-readback;
1323 compatible = "ir-spi-led";
1325 spi-max-frequency = <5000000>;
1326 power-supply = <&irda_regulator>;
1327 duty-cycle = /bits/ 8 <60>;
1328 led-active-low;
1330 controller-data {
1331 samsung,spi-feedback-delay = <0>;
1337 clock-frequency = <24000000>;
1341 vtmu-supply = <&ldo3_reg>;
1346 vtmu-supply = <&ldo3_reg>;
1351 vtmu-supply = <&ldo3_reg>;
1356 vdd33-supply = <&ldo10_reg>;
1357 vdd10-supply = <&ldo6_reg>;
1366 vbus-supply = <&safeout1_reg>;
1371 remote-endpoint = <&muic_to_usb>;
1377 clock-frequency = <24000000>;