Lines Matching +full:vph +full:- +full:supply
1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/gpio/gpio.h>
3 #include <dt-bindings/input/input.h>
4 #include <dt-bindings/leds/common.h>
5 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
6 #include "qcom-msm8974.dtsi"
10 /delete-node/ &mpss_region;
14 compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
23 stdout-path = "serial0:115200n8";
26 gpio-keys {
27 compatible = "gpio-keys";
30 pinctrl-0 = <&msm_keys_default>;
31 pinctrl-names = "default";
33 button-volup {
39 button-general {
46 reserved-memory {
49 no-map;
53 vreg_boost: vreg-boost {
54 compatible = "regulator-fixed";
56 regulator-name = "vreg-boost";
57 regulator-min-microvolt = <3150000>;
58 regulator-max-microvolt = <3150000>;
60 regulator-always-on;
61 regulator-boot-on;
64 enable-active-high;
66 pinctrl-names = "default";
67 pinctrl-0 = <&boost_bypass_n_pin>;
70 vreg_vph_pwr: vreg-vph-pwr {
71 compatible = "regulator-fixed";
72 regulator-name = "vph-pwr";
74 regulator-min-microvolt = <3600000>;
75 regulator-max-microvolt = <3600000>;
77 regulator-always-on;
86 qcom,controlled-remotely;
91 clock-frequency = <200000>;
97 read-only;
110 vdda-supply = <&pm8941_l2>;
111 vdd-supply = <&pm8941_l22>;
112 vddio-supply = <&pm8941_l12>;
117 compatible = "sharp,ls043t1le01-qhd";
120 avdd-supply = <&pm8941_l22>;
122 reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>;
126 remote-endpoint = <&mdss_dsi0_out>;
133 remote-endpoint = <&panel_in>;
134 data-lanes = <0 1 2 3>;
140 vddio-supply = <&pm8941_l12>;
152 msm_keys_default: pm8941-gpio-keys-state {
155 input-enable;
156 drive-push-pull;
157 bias-pull-up;
158 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
159 power-source = <PM8941_GPIO_S3>; /* 1.8V */
164 qcom,power-source = <1>;
192 qcom,cs-out;
193 qcom,switching-freq = <3200>;
195 qcom,num-strings = <1>;
201 cx-supply = <&pm8841_s2>;
203 firmware-name = "qcom/apq8074/adsp.mbn";
209 cx-supply = <&pm8841_s2>;
210 mss-supply = <&pm8841_s3>;
211 mx-supply = <&pm8841_s1>;
212 pll-supply = <&pm8941_l12>;
214 firmware-name = "qcom/apq8074/mba.mbn", "qcom/apq8074/modem.mbn";
220 regulators-0 {
221 compatible = "qcom,rpm-pm8841-regulators";
224 regulator-min-microvolt = <675000>;
225 regulator-max-microvolt = <1050000>;
229 regulator-min-microvolt = <500000>;
230 regulator-max-microvolt = <1050000>;
234 regulator-min-microvolt = <500000>;
235 regulator-max-microvolt = <1050000>;
239 regulator-min-microvolt = <500000>;
240 regulator-max-microvolt = <1050000>;
244 regulators-1 {
245 compatible = "qcom,rpm-pm8941-regulators";
247 vdd_l1_l3-supply = <&pm8941_s1>;
248 vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
249 vdd_l4_l11-supply = <&pm8941_s1>;
250 vdd_l5_l7-supply = <&pm8941_s2>;
251 vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
252 vin_5vs-supply = <&pm8941_5v>;
255 regulator-min-microvolt = <1300000>;
256 regulator-max-microvolt = <1300000>;
257 regulator-always-on;
258 regulator-boot-on;
262 regulator-min-microvolt = <2150000>;
263 regulator-max-microvolt = <2150000>;
264 regulator-boot-on;
268 regulator-min-microvolt = <1800000>;
269 regulator-max-microvolt = <1800000>;
270 regulator-always-on;
271 regulator-boot-on;
275 regulator-min-microvolt = <1225000>;
276 regulator-max-microvolt = <1225000>;
277 regulator-always-on;
278 regulator-boot-on;
282 regulator-min-microvolt = <1200000>;
283 regulator-max-microvolt = <1200000>;
287 regulator-min-microvolt = <1225000>;
288 regulator-max-microvolt = <1225000>;
292 regulator-min-microvolt = <1225000>;
293 regulator-max-microvolt = <1225000>;
297 regulator-min-microvolt = <1800000>;
298 regulator-max-microvolt = <1800000>;
302 regulator-min-microvolt = <1800000>;
303 regulator-max-microvolt = <1800000>;
304 regulator-boot-on;
308 regulator-min-microvolt = <1800000>;
309 regulator-max-microvolt = <1800000>;
310 regulator-boot-on;
314 regulator-min-microvolt = <1800000>;
315 regulator-max-microvolt = <1800000>;
319 regulator-min-microvolt = <1800000>;
320 regulator-max-microvolt = <2950000>;
324 regulator-min-microvolt = <1800000>;
325 regulator-max-microvolt = <1800000>;
326 regulator-always-on;
330 regulator-min-microvolt = <1300000>;
331 regulator-max-microvolt = <1300000>;
335 regulator-min-microvolt = <1800000>;
336 regulator-max-microvolt = <1800000>;
337 regulator-always-on;
338 regulator-boot-on;
342 regulator-min-microvolt = <1800000>;
343 regulator-max-microvolt = <2950000>;
344 regulator-boot-on;
348 regulator-min-microvolt = <1800000>;
349 regulator-max-microvolt = <1800000>;
353 regulator-min-microvolt = <2050000>;
354 regulator-max-microvolt = <2050000>;
358 regulator-min-microvolt = <2700000>;
359 regulator-max-microvolt = <2700000>;
363 regulator-min-microvolt = <2700000>;
364 regulator-max-microvolt = <2700000>;
368 regulator-min-microvolt = <2850000>;
369 regulator-max-microvolt = <2850000>;
373 regulator-min-microvolt = <3300000>;
374 regulator-max-microvolt = <3300000>;
375 regulator-always-on;
379 regulator-min-microvolt = <2950000>;
380 regulator-max-microvolt = <2950000>;
381 regulator-system-load = <200000>;
382 regulator-allow-set-load;
383 regulator-boot-on;
387 regulator-min-microvolt = <2950000>;
388 regulator-max-microvolt = <2950000>;
389 regulator-boot-on;
393 regulator-min-microvolt = <3000000>;
394 regulator-max-microvolt = <3000000>;
398 regulator-min-microvolt = <3000000>;
399 regulator-max-microvolt = <3000000>;
403 regulator-min-microvolt = <3075000>;
404 regulator-max-microvolt = <3075000>;
405 regulator-boot-on;
413 vmmc-supply = <&pm8941_l20>;
414 vqmmc-supply = <&pm8941_s3>;
416 pinctrl-names = "default", "sleep";
417 pinctrl-0 = <&sdc1_on>;
418 pinctrl-1 = <&sdc1_off>;
424 cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
425 vmmc-supply = <&pm8941_l21>;
426 vqmmc-supply = <&pm8941_l13>;
428 pinctrl-names = "default", "sleep";
429 pinctrl-0 = <&sdc2_on>;
430 pinctrl-1 = <&sdc2_off>;
438 sdc1_on: sdc1-on-state {
439 clk-pins {
441 drive-strength = <16>;
442 bias-disable;
445 cmd-data-pins {
447 drive-strength = <10>;
448 bias-pull-up;
452 sdc2_on: sdc2-on-state {
453 clk-pins {
455 drive-strength = <10>;
456 bias-disable;
459 cmd-data-pins {
461 drive-strength = <6>;
462 bias-pull-up;
465 cd-pins {
468 drive-strength = <2>;
469 bias-disable;
478 phy-select = <&tcsr 0xb000 1>;
480 vbus-supply = <&chg_otg>;
481 hnp-disable;
482 srp-disable;
483 adp-disable;
488 v3p3-supply = <&pm8941_l24>;
489 v1p8-supply = <&pm8941_l6>;
491 qcom,init-seq = /bits/ 8 <0x1 0x63>;