Lines Matching +full:input +full:- +full:enable
9 * Released under the terms of 3-clause BSD License
13 /dts-v1/;
18 #include "dt-bindings/input/input.h"
19 #include "dt-bindings/gpio/gpio.h"
23 compatible = "hitex,lpc4350-eval-board", "nxp,lpc4350";
33 stdout-path = &uart0;
42 compatible = "gpio-keys-polled";
43 poll-interval = <100>;
97 compatible = "gpio-leds";
102 linux,default-trigger = "heartbeat";
122 compatible = "regulator-fixed";
123 regulator-name = "3v3io";
124 regulator-min-microvolt = <3300000>;
125 regulator-max-microvolt = <3300000>;
130 adc1_pins: adc1-pins {
134 input-disable;
135 bias-disable;
139 emc_pins: emc-pins {
148 slew-rate = <1>;
149 bias-disable;
150 input-enable;
151 input-schmitt-disable;
160 slew-rate = <1>;
161 bias-disable;
162 input-enable;
163 input-schmitt-disable;
169 slew-rate = <1>;
170 bias-disable;
171 input-enable;
172 input-schmitt-disable;
178 slew-rate = <1>;
179 bias-disable;
180 input-enable;
181 input-schmitt-disable;
187 slew-rate = <1>;
188 bias-disable;
189 input-enable;
190 input-schmitt-disable;
196 slew-rate = <1>;
197 bias-disable;
198 input-enable;
199 input-schmitt-disable;
205 slew-rate = <1>;
206 bias-disable;
207 input-enable;
208 input-schmitt-disable;
214 slew-rate = <1>;
215 bias-disable;
216 input-enable;
217 input-schmitt-disable;
223 slew-rate = <1>;
224 bias-disable;
225 input-enable;
226 input-schmitt-disable;
232 slew-rate = <1>;
233 bias-disable;
234 input-enable;
235 input-schmitt-disable;
239 enet_mii_pins: enet-mii-pins {
243 bias-disable;
244 input-enable;
250 bias-disable;
256 bias-disable;
257 input-enable;
263 bias-disable;
264 input-enable;
270 bias-disable;
271 input-enable;
277 bias-disable;
278 input-enable;
284 bias-disable;
288 i2c0_pins: i2c0-pins {
292 input-enable;
296 spifi_pins: spifi-pins {
300 slew-rate = <1>;
301 bias-disable;
302 input-enable;
303 input-schmitt-disable;
309 slew-rate = <1>;
310 bias-disable;
311 input-enable;
312 input-schmitt-disable;
318 slew-rate = <1>;
319 bias-disable;
320 input-enable;
321 input-schmitt-disable;
325 uart0_pins: uart0-pins {
329 input-schmitt-disable;
330 bias-disable;
331 input-enable;
337 bias-pull-down;
344 vref-supply = <&vcc>;
345 pinctrl-names = "default";
346 pinctrl-0 = <&adc1_pins>;
351 pinctrl-names = "default";
352 pinctrl-0 = <&emc_pins>;
355 #address-cells = <2>;
356 #size-cells = <1>;
360 mpmc,memory-width = <16>;
361 mpmc,byte-lane-low;
362 mpmc,write-enable-delay = <0>;
363 mpmc,output-enable-delay = <0>;
364 mpmc,read-access-delay = <70>;
365 mpmc,page-mode-read-delay = <70>;
368 compatible = "sst,sst39vf320", "cfi-flash";
370 bank-width = <2>;
371 #address-cells = <1>;
372 #size-cells = <1>;
392 #address-cells = <2>;
393 #size-cells = <1>;
397 mpmc,memory-width = <16>;
398 mpmc,byte-lane-low;
399 mpmc,write-enable-delay = <0>;
400 mpmc,output-enable-delay = <30>;
401 mpmc,read-access-delay = <90>;
402 mpmc,page-mode-read-delay = <55>;
403 mpmc,write-access-delay = <55>;
404 mpmc,turn-round-delay = <55>;
407 compatible = "mmio-sram";
414 clock-frequency = <25000000>;
419 pinctrl-names = "default";
420 pinctrl-0 = <&i2c0_pins>;
421 clock-frequency = <400000>;
425 compatible = "nxp,se97", "jedec,jc-42.4-temp";
437 gpio-controller;
438 #gpio-cells = <2>;
444 phy-mode = "mii";
445 pinctrl-names = "default";
446 pinctrl-0 = <&enet_mii_pins>;
451 pinctrl-names = "default";
452 pinctrl-0 = <&spifi_pins>;
455 compatible = "jedec,spi-nor";
456 spi-rx-bus-width = <4>;
457 #address-cells = <1>;
458 #size-cells = <1>;
479 pinctrl-names = "default";
480 pinctrl-0 = <&uart0_pins>;