Lines Matching +full:vbus +full:- +full:divider
1 // SPDX-License-Identifier: (GPL-2.0-only OR MIT)
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/interrupt-controller/irq.h>
21 stdout-path = &uart2;
24 gpio-keys {
25 compatible = "gpio-keys";
27 user-pb {
33 user-pb1x {
36 interrupt-parent = <&gsc>;
40 key-erased {
41 label = "key-erased";
43 interrupt-parent = <&gsc>;
47 eeprom-wp {
50 interrupt-parent = <&gsc>;
57 interrupt-parent = <&gsc>;
61 switch-hold {
64 interrupt-parent = <&gsc>;
70 compatible = "gpio-leds";
71 pinctrl-names = "default";
72 pinctrl-0 = <&pinctrl_gpio_leds>;
74 led0: led-user1 {
77 default-state = "on";
78 linux,default-trigger = "heartbeat";
81 led1: led-user2 {
84 default-state = "off";
94 compatible = "pps-gpio";
95 pinctrl-names = "default";
96 pinctrl-0 = <&pinctrl_pps>;
101 reg_5p0v: regulator-5p0v {
102 compatible = "regulator-fixed";
103 regulator-name = "5P0V";
104 regulator-min-microvolt = <5000000>;
105 regulator-max-microvolt = <5000000>;
106 regulator-always-on;
109 reg_usb_otg_vbus: regulator-usb-otg-vbus {
110 compatible = "regulator-fixed";
111 regulator-name = "usb_otg_vbus";
112 regulator-min-microvolt = <5000000>;
113 regulator-max-microvolt = <5000000>;
115 enable-active-high;
120 pinctrl-names = "default";
121 pinctrl-0 = <&pinctrl_gpmi_nand>;
126 pinctrl-names = "default";
127 pinctrl-0 = <&pinctrl_hdmi>;
128 ddc-i2c-bus = <&i2c3>;
133 clock-frequency = <100000>;
134 pinctrl-names = "default";
135 pinctrl-0 = <&pinctrl_i2c1>;
141 interrupt-parent = <&gpio1>;
143 interrupt-controller;
144 #interrupt-cells = <1>;
145 #size-cells = <0>;
148 compatible = "gw,gsc-adc";
149 #address-cells = <1>;
150 #size-cells = <0>;
229 gpio-controller;
230 #gpio-cells = <2>;
231 interrupt-parent = <&gsc>;
266 clock-frequency = <100000>;
267 pinctrl-names = "default";
268 pinctrl-0 = <&pinctrl_i2c2>;
272 compatible = "st,lsm9ds1-magn";
274 pinctrl-names = "default";
275 pinctrl-0 = <&pinctrl_mag>;
276 interrupt-parent = <&gpio1>;
281 compatible = "st,lsm9ds1-imu";
283 st,drdy-int-pin = <1>;
284 pinctrl-names = "default";
285 pinctrl-0 = <&pinctrl_imu>;
286 interrupt-parent = <&gpio7>;
293 pinctrl-names = "default";
294 pinctrl-0 = <&pinctrl_pmic>;
295 interrupt-parent = <&gpio1>;
301 regulator-name = "vddsoc";
302 regulator-min-microvolt = <674400>;
303 regulator-max-microvolt = <1308000>;
304 lltc,fb-voltage-divider = <127000 200000>;
305 regulator-ramp-delay = <7000>;
306 regulator-boot-on;
307 regulator-always-on;
312 regulator-name = "vddddr";
313 regulator-min-microvolt = <868310>;
314 regulator-max-microvolt = <1684000>;
315 lltc,fb-voltage-divider = <221000 200000>;
316 regulator-ramp-delay = <7000>;
317 regulator-boot-on;
318 regulator-always-on;
323 regulator-name = "vddarm";
324 regulator-min-microvolt = <674400>;
325 regulator-max-microvolt = <1308000>;
326 lltc,fb-voltage-divider = <127000 200000>;
327 regulator-ramp-delay = <7000>;
328 regulator-boot-on;
329 regulator-always-on;
334 regulator-name = "vdd3p3";
335 regulator-min-microvolt = <1880000>;
336 regulator-max-microvolt = <3647000>;
337 lltc,fb-voltage-divider = <200000 56200>;
338 regulator-ramp-delay = <7000>;
339 regulator-boot-on;
340 regulator-always-on;
345 regulator-name = "vdd1p8a";
346 regulator-min-microvolt = <1816125>;
347 regulator-max-microvolt = <1816125>;
348 lltc,fb-voltage-divider = <301000 200000>;
349 regulator-boot-on;
350 regulator-always-on;
355 regulator-name = "vdd1p8b";
356 regulator-min-microvolt = <1800000>;
357 regulator-max-microvolt = <1800000>;
358 regulator-boot-on;
363 regulator-name = "vdd3p0";
364 regulator-min-microvolt = <3023250>;
365 regulator-max-microvolt = <3023250>;
366 lltc,fb-voltage-divider = <634000 200000>;
367 regulator-boot-on;
368 regulator-always-on;
375 clock-frequency = <100000>;
376 pinctrl-names = "default";
377 pinctrl-0 = <&pinctrl_i2c3>;
382 pinctrl-names = "default";
383 pinctrl-0 = <&pinctrl_adv7180>;
385 powerdown-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
386 interrupt-parent = <&gpio5>;
391 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
392 bus-width = <8>;
399 bus-width = <8>;
403 remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
404 bus-width = <8>;
408 pinctrl-names = "default";
409 pinctrl-0 = <&pinctrl_ipu1_csi0>;
413 pinctrl-names = "default";
414 pinctrl-0 = <&pinctrl_pcie>;
415 reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
420 pinctrl-names = "default";
421 pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
426 pinctrl-names = "default";
427 pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
432 pinctrl-names = "default";
433 pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
438 pinctrl-names = "default";
439 pinctrl-0 = <&pinctrl_uart2>;
444 pinctrl-names = "default";
445 pinctrl-0 = <&pinctrl_uart3>;
450 pinctrl-names = "default";
451 pinctrl-0 = <&pinctrl_uart4>;
456 pinctrl-names = "default";
457 pinctrl-0 = <&pinctrl_uart5>;
466 vbus-supply = <®_usb_otg_vbus>;
467 pinctrl-names = "default";
468 pinctrl-0 = <&pinctrl_usbotg>;
469 disable-over-current;
474 pinctrl-names = "default", "state_100mhz", "state_200mhz";
475 pinctrl-0 = <&pinctrl_usdhc3>;
476 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
477 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
478 cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
483 pinctrl-names = "default";
484 pinctrl-0 = <&pinctrl_wdog>;
485 fsl,ext-reset-output;
665 pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
678 pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {